SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
High temperature creep studies on unaltered, and recrystallized nickel alloys
Extruded prealloyed powder evaluation for two nickel-base alloys
Stress corrosion cracking behavior in titanium, molybdenum, and aluminum alloys, and electrochemical kinetic studies
Weldability and thermal stability of refractory metal alloys
Effect of oxygen contamination on weldability of refractory metal alloys
Tungsten alloy fiber reinforced Ni-base superalloy composites evaluated for high temperature turbojet engine applications, considering stress-rupture strength, oxidation and impact resistance
Phase equilibrium of Fe-rich Fe-Al alloys using single crystal X ray diffraction
Fe rich Fe-Al alloys single crystals, determining three dimensional order and atomic displacements coefficients by X ray diffuse scattering
Long-time temperature stability of refractory metal alloys and weldability determinations
Weldability of tungsten base alloys and elevated temperature stability
Edge and surface modifications of niobium alloys were investigated prior to coating with Si-20Cr-20Fe and slurry composition modification for performance in a 1370 C ambient pressure slow cycle test. The best coating obtained was Si-20Cr-20Mn with an average life of 63 cycles, compared to 40 for Si-20Cr-20Fe on FS-85 (100 percent improvement in weight parity life). Edge beading extended the lives of Si-20Cr-20Fe-coated Cb-752 and FS-85 to 57 and 41 cycles respectively (50 and 20 percent improvements in weight parity life respectively). W, Al2O3 and ZrO2(CaO) surface modifications altered coating crack frequency and microstructure and increased life somewhat.
Edge and surface modification of niobium alloys prior to coating with Si-20Cr-20Fe and slurry composition modification were investigated to improve performance in a 1370 C, ambient pressure, slow-cycle test. The best coating obtained was Si-20Cr-20Mn with an average life of 63 cycles compared to 40 for Si-20Cr-20Fe on FS-85 (100 percent improvement in weight parity life). Edge beading extended the lives of Si-20Cr-20Fe coated Cb-752 and FS-85 to 57 and 41 cycles, respectively (50 and 20 percent improvements in weight parity life, respectively).
Correlation between differential scanning calorimetry and high temperature transmission electron microscopy for the characterization of preexisting matrix precipitates in the highest-strength and overaged tempers of 7075 aluminum was demonstrated. The solid state reactions undergone by these tempers in the 20-500 C temperature range were elucidated and expressed in terms of thermodynamic and kinetic parameters. The dissolution parameters for each phase are distinguishable and serve as guidelines for a rapid characterization of the matrix microstructure of these alloys.
Cyclic furnace and cyclic natural gas-oxygen torch rig tests were conducted to (1) identify a thermal-barrier system for a nickel-aluminum-molybdenum alloy, (2) study the oxidation of the bond coating, and (3) study the effect of the substrate coefficient of thermal expansion on thermal barrier system life. It is found that the latter is affected by the composition of the bond coating, yttria concentration in zirconia, and the coefficient of thermal expansion of the substrate material. In addition, small compositional changes in the bond and thermal barrier coatings have greater effect on thermal barrier system life than the 40% increase in the coefficient of thermal expansion of the substrate material. No simple relation exists between the weight gain caused by bond-coating oxidation with increasing yttria concentration in zirconia and increasing bond coating thickness on the one hand, and thermal barrier system life on the other.
Mechanical alloying is being investigated as a processing route for the production of aluminide intermetallics. This program involves powder production and characterization, consolidation and thermal treatments and determination of microstructure-property relationships. An attritor mill is being used to produce powder in lots up to 1000 grams and the processing parameters are being systematically varied to establish the optimum milling conditions. The mill is being instrumented to generate data related to the processing to provide a basis for theoretical modeling. Powder is being characterized using thermal analysis, optical and electron microscopy and X-ray diffraction. Particle size distributions and powder density are being determined. Consolidation of the powder is being approached in several different ways including, cold isostatic pressing, sintering, extrusion and hot pressing. The results of the program so far will be presented and future directions discussed.