Results for “aerospace composites” — Page 5

NASA NTRS2002

Thermomechanical Response Variability of Stiffened Composite Panels

A significant numerical simulation capability now exists for studying the various phenomena associated with the response, failure, and performance of multilayered composite panels and shells subjected to combined pressure, mechanical, and thermal loads. The phenomena involved cover a wide range of length scales from local to global structural response. The modeling approaches used for multilayered panels include micromechanical models, three-dimensional continuum models, quasi-three-dimensional models, and two-dimensional plate and shell models. Within each category a number of models with several levels of sophistication has evolved. The four categories are described in review papers. Despite the extensive literature cited in the afore-mentioned references, only a few studies have been reported on the effects of stiffness discontinuities, such as those associated with an abrupt stiffener termination or dropped plies, on the response of composite panel. Stiffener termination is often necessary in composite aerospace structures to satisfy detailed design requirements, and therefore an understanding and a prediction of its effect on the response and failure of composite panels are desirable. Such a prediction must take into account the fact that current measurement technology does not allow the accurate determination of the material parameters that are used in the analytical models.

Noor, Ahmed K.↗

NASA NTRS1994

Society of the plastic industry process emission initiatives

At first view, plastics process emissions research may not seem to have much bearing on outgassing considerations relative to advanced composite materials; however, several parallel issues and cross currents are of mutual interest. The following topics are discussed: relevance of plastics industry research to aerospace composites; impact of clean air act amendment requirements; scope of the Society of the Plastics Industry, Inc. activities in thermoplastic process emissions and reinforced plastics/composites process emissions; and utility of SPI research for advanced polymer composites audiences.

Mcdermott, Joseph↗

NASA NTRS2013

Methodologies for Combined Loads Tests Using a Multi-Actuator Test Machine

The NASA Langley COmbined Loads Test System (COLTS) Facility was designed to accommodate a range of fuselage structures and wing sections and subject them to both quasistatic and cyclic loading conditions. Structural tests have been conducted in COLTS that address structural integrity issues of metallic and fiber reinforced composite aerospace structures in support of NASA Programs (i.e. the Aircraft Structural Integrity (ASIP) Program, High-Speed-Research program and the Supersonic Project, NASA Engineering and Safety Center (NESC) Composite Crew Module Project, and the Environmentally Responsible Aviation Program),. This paper presents experimental results for curved panels subjected to mechanical and internal pressure loads using a D-box test fixture. Also, results are presented that describe use of a checkout beam for development of testing procedures for a combined mechanical and pressure loading test of a Multi-bay box. The Multi-bay box test will be used to experimentally verify the structural performance of the Multi-bay box in support of the Environmentally Responsible Aviation Project at NASA Langley.

Rouse, Marshall↗

NASA NTRSDate not supplied

TPSAS-NF1676L-25778-DND

Testing required to design and certify aircraft structures has increased dramatically with the growth in use of composite materials, and the development time and cost have become an issue as industry looks towards the next generation of aircraft. To help address this challenge, NASA has formed an industry-spanning consortium with the goal of cutting by 30% today's 10-year timeline for developing and certifying composite aircraft structures. This goal is to be achieved by infusing leading edge, physics-based tools to improve the prediction of the response and failure of composite aerospace structures. The plan for the public-private partnership of NASA, the FAA, airframe manufacturers, aircraft engine manufacturers, and several universities is to conduct joint research under the five-year Advanced Composites Program (ACP). The emphasis of the ACP project is the development of damage prediction and non-destructive inspection methods capabilities that are sufficiently reliable to enable a reduction in the element and subcomponent testing necessary for design and certification. ACP also is expected to create rapid design tools to speed preliminary design and improve safety and performance. A critical element of this research concerns the residual strength of postbuckled stiffened panels with impact damage. This presentation will discuss different aspects of ongoing research on the prediction of structural collapse due to skin/stiffener separation. In particular, the presentation will examine issues that must be addressed in the analysis, such as R-curve toughening, delamination migration, bridging, as well as some unexpected effects of ply orientation.

Carlos G Davila↗

NASA NTRS2003

Colossal Tooling Design: 3D Simulation for Ergonomic Analysis

The application of high-level 3D simulation software to the design phase of colossal mandrel tooling for composite aerospace fuel tanks was accomplished to discover and resolve safety and human engineering problems. The analyses were conducted to determine safety, ergonomic and human engineering aspects of the disassembly process of the fuel tank composite shell mandrel. Three-dimensional graphics high-level software, incorporating various ergonomic analysis algorithms, was utilized to determine if the process was within safety and health boundaries for the workers carrying out these tasks. In addition, the graphical software was extremely helpful in the identification of material handling equipment and devices for the mandrel tooling assembly/disassembly process.

Hunter, Steve L.↗

NASA NTRS1984

Rapid adhesive bonding concepts for specimen and panel fabrication and field repair

The NASA Langley Research Center has developed bonding concepts for aerospace composite materials which employ induction heating to directly apply heat to the bond line and/or adherends without simultaneously heating the entire structure, supports, and fixtures of a bonding assembly. These methods have demonstrated bonding process time reductions of two to three orders of magnitude, by comparison with conventional press molding. Attention is presently given to rapid adhesive bonding for lap shear specimens for aerospace panel bonding or field repair, as well as for the field repair requirements of metallic and advanced polymeric matrix composite structures.

Stein, B. A.↗

NASA NTRS2012

Resin Systems and Chemistry-Degradation Mechanisms and Durability in Long-Term Durability of Polymeric Matrix Composites

In choosing a polymer-matrix composite material for a particular application, a number of factors need to be weighed. Among these are mechanical requirements, fabrication method (e.g. press-molding, resin infusion, filament winding, tape layup), and use conditions. Primary among the environmental exposures encountered in aerospace structures are moisture and elevated temperatures, but certain applications may require resistance to other fluids and solvents, alkaline agents, thermal cycling, radiation, or rapid, localized heating (for example, lightning strike). In this chapter, the main classes of polymer resin systems found in aerospace composites will be discussed. Within each class, their responses to environmental factors and the associated degradation mechanisms will be reviewed.

Hinkley, Jeffrey A.↗

NASA NTRS2017

Development of an Input Suite for an Orthotropic Composite Material Model

An orthotropic three-dimensional material model suitable for use in modeling impact tests has been developed that has three major components elastic and inelastic deformations, damage and failure. The material model has been implemented as MAT213 into a special version of LS-DYNA and uses tabulated data obtained from experiments. The prominent features of the constitutive model are illustrated using a widely-used aerospace composite the T800S3900-2B[P2352W-19] BMS8-276 Rev-H-Unitape fiber resin unidirectional composite. The input for the deformation model consists of experimental data from 12 distinct experiments at a known temperature and strain rate: tension and compression along all three principal directions, shear in all three principal planes, and off axis tension or compression tests in all three principal planes, along with other material constants. There are additional input associated with the damage and failure models. The steps in using this model are illustrated composite characterization tests, verification tests and a validation test. The results show that the developed and implemented model is stable and yields acceptably accurate results.

finite element method↗

NASA NTRS2012

Voluntary Consensus Organization Standards for Nondestructive Evaluation of Thin-Walled Metallic Liners and Composite Overwraps in Composite Overwrapped Pressure Vessels

NASA fracture control requirements outlined in NASA-STD-5009 and NASA-STD-5014 are predicated on the availability and use of sensitive nondestructive evaluation (NDE) methods that can detect and monitor defects, thereby providing data that can be used to predict failure or reduce the risk of failure in fracture critical components. However, in the case of composite materials and components, including composite overwrapped pressure vessels (COPVs), the effect of defects is poorly understood, the NDE methods used to evaluate locate and size defects are typically at lower technical readiness level than analogous NDE methods used for metals, and demonstration studies to verify the probability of detection (POD) are generally lacking or unavailable. These factors together make failure prediction of fracture critical composite materials and components based on size, quantity, or orientation of defects nearly impossible. Also, when inspecting metal liners in as-manufactured COPVs, sensitivity is lost and only the inner surface of the liner is accessible. Also, NDE of COPVs as applied during manufacturing varies significantly from manufacturer to manufacturer and has not yet been standardized. Although requirements exist to perform NDE immediately after manufacturing to establish initial integrity of the parts, procedural detail for NDE of composites is still nonexistent or under development. For example, in practice, only a visual inspection of COPVs is performed during manufacturing and service, leaving in question whether defects of concern, for example, bridging, overwrap winding anomalies, impact damage below visible threshold, out-of-family strain growth, and liner buckling have been adequately detected and monitored. To address these shortcomings, in 2005 the NASA Nondestructive Evaluation Working Group (NNWG) began funding work to develop and adopt standards for nondestructive evaluation of aerospace composites in collaboration with the American Society for Testing and Materials (ASTM) Committee E07 on Nondestructive Testing. Similarly, in 2006 the NASA Engineering and Safety Center (NESC) recommended that nondestructive evaluation methods that can predict composite failure in COPVs should be developed and verified, and integrated into the damage control plan for these vessels

Waller, Jess↗

NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

NASA NTRSDate not supplied

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

NASA NTRS2007

Recent Advances in Durability and Damage Tolerance Methodology at NASA Langley Research Center

Durability and damage tolerance (D&DT) issues are critical to the development of lighter, safer and more efficient aerospace vehicles. Durability is largely an economic life-cycle design consideration whereas damage tolerance directly addresses the structural airworthiness (safety) of the vehicle. Both D&DT methodologies must address the deleterious effects of changes in material properties and the initiation and growth of damage that may occur during the vehicle s service lifetime. The result of unanticipated D&DT response is often manifested in the form of catastrophic and potentially fatal accidents. As such, durability and damage tolerance requirements must be rigorously addressed for commercial transport aircraft and NASA spacecraft systems. This paper presents an overview of the recent and planned future research in durability and damage tolerance analytical and experimental methods for both metallic and composite aerospace structures at NASA Langley Research Center (LaRC).

Ransom, J. B.↗

NASA NTRS2020

A Review of LIBS for Real-Time Detection of Trace Silicone Contaminants on CFRP Surfaces

Laser ablation is the removal of material by laser pulses through photochemical, photothermal, or photophysical mechanisms, which is useful to prepare an adherend surface for adhesive bonding. Laser surface treatment is a method that has been under research for the past decade at NASA Langley Research Center (LaRC) to prepare surfaces for adhesive joining of aerospace composite materials and metallic alloys. Laser ablation of composite materials increases surface area and removes the surface contaminants introduced during material handling and fabrication processes. By adjustment of laser parameters, it is possible to obtain repeatable surface conditions, and superficial contaminants can be selectively and efficiently removed without damaging the underlying carbon fibers or the carbon fiber reinforced polymer (CFRP) substrate. Laser induced breakdown spectroscopy (LIBS) is a surface characterization and inspection technique that can be seamlessly integrated into the laser surface treatment process. At NASA LaRC, a single laser system has been used for both laser surface treatment and LIBS, which enables in-situ monitoring of surface contaminants. This work focuses on the advancements at LaRC using LIBS to detect surface silicone contaminants on aerospace CFRP materials and to provide surface quality control in adhesive bonding.

Rodolfo I Ledesma↗

NASA NTRS2020

A Review of LIBS for Real-Time Detection of Trace Silicone Contaminants on CFRP Surfaces

Laser ablation is the removal of material by laser pulses through photochemical, photothermal, or photophysical mechanisms, which is useful to prepare an adherend surface for adhesive bonding. Laser surface treatment is a method that has been under research for the past decade at NASA Langley Research Center (LaRC) to prepare surfaces for adhesive joining of aerospace composite materials and metallic alloys. Laser ablation of composite materials increases surface area and removes the surface contaminants introduced during material handling and fabrication processes. By adjustment of laser parameters, it is possible to obtain repeatable surface conditions, and superficial contaminants can be selectively and efficiently removed without damaging the underlying carbon fibers or the carbon fiber reinforced polymer (CFRP) substrate. Laser induced breakdown spectroscopy (LIBS) is a surface characterization and inspection technique that can be seamlessly integrated into the laser surface treatment process. At NASA LaRC, a single laser system has been used for both laser surface treatment and LIBS, which enables in-situ monitoring of surface contaminants. This work focuses on the advancements at LaRC using LIBS to detect surface silicone contaminants on aerospace CFRP materials and to provide surface quality control in adhesive bonding.

Rodolfo I Ledesma↗

NASA NTRS2016

Advances in In-Situ Inspection of Automated Fiber Placement Systems

The advent of Automated Fiber Placement (AFP) systems have aided the rapid manufacturing of composite aerospace structures. One of the challenges that AFP systems present is the uniformity of the deposited prepreg tape layers, which are prone to laps, gaps, overlaps and twists. The current detection modus operandi involves halting fabrication and performing a time consuming visual inspection of each tape layer. Typical AFP systems use a quartz lamp to heat the base layer to make the surface tacky as it deposits another tape layer. The idea was proposed to use the preheated base layer as a through transmission heat source and to inspect the newly added tape layer using a thermographic camera. As a preliminary study of this concept a laboratory proof of concept device was designed and constructed to simulate the through transmission heat source. Using the proof of concept device, we inspected an AFP-built uncured composite specimen with artificial manufacturing defects. This paper will discuss the results of this preliminary study and the implications involved with deploying a full-scale AFP inspection system.

Juarez, Peter D.↗

NASA NTRS2014

Challenges in Modelling of Lightning-Induced Delamination; Effect of Temperature-Dependent Interfacial Properties

Lightning is a major cause of damage in laminated composite aerospace structures during flight. Due to the dielectric nature of Carbon fiber reinforced polymers (CFRPs), the high energy induced by lightning strike transforms into extreme, localized surface temperature accompanied with a high-pressure shockwave resulting in extensive damage. It is crucial to develop a numerical tool capable of predicting the damage induced from a lightning strike to supplement extremely expensive lightning experiments. Delamination is one of the most significant failure modes resulting from a lightning strike. It can be extended well beyond the visible damage zone, and requires sophisticated techniques and equipment to detect. A popular technique used to model delamination is the cohesive zone approach. Since the loading induced from a lightning strike event is assumed to consist of extreme localized heating, the cohesive zone formulation should additionally account for temperature effects. However, the sensitivity to this dependency remains unknown. Therefore, the major focus point of this work is to investigate the importance of this dependency via defining various temperature dependency profiles for the cohesive zone properties, and analyzing the corresponding delamination area. Thus, a detailed numerical model consisting of multidirectional composite plies with temperature-dependent cohesive elements in between is subjected to lightning (excessive amount of heat and pressure) and delamination/damage expansion is studied under specified conditions.

interlaminar damage↗

NASA NTRS1985

Filament winding - Waking the sleeping giant

The use of filament winding (FW) in the production of aerospace composite structures is examined. The FW process applies spools of fiber and prepreg tow or prepreg tape to a male mandrel; the process is more efficient and cost effective than metallic construction. The fibers used in FW and the curing process are explained. The reduced storage and fabrication costs that result from FW are discussed. The use of FW to produce a filament-wound case for a solid rocket motor and the substructure and skin of an aircraft fuselage are described. Areas which require further development in order to expand the use of FW are listed and discussed.

Freeman, W. T., Jr.↗

NASA NTRS1985

Aerospace applications of PMR polyimide composites

The current status of the novel class of processable, addition-type polyimides known as PMR (for in situ polymerization of monomer reactants) polyimides, developed by NASA at the Lewis Research Center, is reviewed. Highlights of PMR technology studies conducted at NASA Lewis are presented. Several examples of industrial applications of PMR-15 polyimide composites to aerospace structural components are examined.

Serafini, T. T.↗