Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “V(HO)2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

89 records · Page 5

23.4% monolithic epitaxial GaAsP/Si tandem solar cells and quantification of losses from threading dislocations

A 2-terminal, dual-junction, epitaxially integrated, GaAsP/Si tandem solar cell with an 3rd party certified efficiency of 23.4 % was fabricated via MOCVD growth on an ex-situ produced Si sub cell. The drastic efficiency improvement over the authors previous peer-reviewed demonstration of such a device architecture is examined. Critical advancements in top cell design to maximize short wavelength response were critical in enabling improved top cell response. An in-depth analysis of this champion tandem cell has identified key loss mechanisms which elucidate the pathway for further efficiency gains. First, voltage dependent collection efficiency in the GaAsP top cell is the primary cause of fill factor losses currently limiting efficiency. Analysis of spectrally resolved I–V measurements and analytical device modeling and indicate poor diffusion length due to elevated dislocation densities as the likely cause for the voltage dependent collection efficiency. Second, modeling for the GaAs 0.75 P 0.25 top cell, using experimental data at multiple dislocation densities, provides quantitative understanding of the current and voltage losses associated with threading dislocations providing a clear efficiency pathway with reduction in dislocation density. Finally, Si subcell modeling identifies the pathway for further Si subcell advances over the present, simplistic design, which has yet to employ the known benefits of rear surface texture or dielectric passivation.

14 SOLAR ENERGY↗

Detection of compact ultraviolet nuclear emission in liner galaxies

Low-ionization nuclear emission-line regions (LINERs), which exist in a large fraction of galaxies, may be the least luminous manifestation of quasar activity. As such, they may make possible the study of the active galactic nucleus (AGN) phenomenon in the nearest galaxies. The nature of LINERs has, however, remained controversial because an AGN-like nonstellar continuum source has not been directly observed in them. We report the detection of bright (greater than or approximately = 2 x 10(exp -16) ergs/s/sq cm/A), unresolved (full width at half maximum (FWHM) less than or approximately = 0.1 sec) point sources of UV (approximately 2300 A) emission in the nuclei of nine nearby galaxies. The galaxies were imaged using the Faint Object Camera (FOC) on the Hubble Space Telescope (HST), and seven of them are from a complete sample of 110 nearby galaxies that was observed with HST. Ground-based optical spectroscopy reveals that five of the nuclei are LINERs, three are starburst nuclei, and one is a Seyfert nucleus. The observed UV flux in each of the five LINERs implies an ionizing flux that is sufficient to account to the observed emission lines through photoionization. The detection of a strong UV continuum in the LINERs argues against shock excitation as the source of the observed emission lines, and supports the idea that photoionization excites the lines in at least some objects of this class. We have analyzed ground-based spectra for most of the northern-hemisphere galaxies in the HST sample and find that 26 of them are LINERs, among which only the above five LINERs have a detected nuclear UV source.

Maoz, Dan↗

Global and Regional Decreases in Tropospheric Oxidants from Photochemical Effects of Aerosols

We evaluate the sensitivity of tropospheric OH, O3, and O3 precursors to photochemical effects of aerosols not usually included in global models: (1) aerosol scattering and absorption of ultraviolet radiation and (2) reactive uptake of HO', NO2, and NO3. Our approach is to couple a global 3-D model of tropospheric chemistry (GEOS- CHEM) with aerosol fields from a global 3-D aerosol model (GOCART). Reactive uptake by aerosols is computed using reaction probabilities from a recent review (gamma(sub HO2) = 0.2, gamma(sub NO2) = 10(exp -4), gamma(sub NO3) = l0(exp -3). Aerosols decrease the O3 - O((sup 1)D) photolysis frequency by 5-20% at the surface throughout the Northern Hemisphere (largely due to mineral dust) and by a factor of 2 in biomass burning regions (largely due to black carbon). Aerosol uptake of HO2 accounts for 10-40% of total HOx radical ((triple bonds)OH + peroxy) loss in the boundary layer over polluted continental regions (largely due to sulfate and organic carbon) and for more than 70% over tropical biomass burning regions (largely due to organic carbon). Uptake of NO2 and NO3 accounts for 10-20% of total HNO3 production over biomass burning regions and less elsewhere. Annual mean OH concentrations decrease by 9% globally and by 5-35% in the boundary layer over the Northern Hemisphere. Simulated CO increases by 5- 15 ppbv in the remote Northern Hemisphere, improving agreement with observations. Simulated boundary layer O3 decreases by 15- 45 ppbv over India during the biomass burning season in March and by 5-9 ppbv over northern Europe in August, again improving comparison with observations. We find that particulate matter controls would increase surface O3 over Europe and other industrial regions.

Martin, Randall V.↗

Increased Ion Temperature and Neutron Yield Observed in Magnetized Indirectly Driven $\mathrm{D_2}$-Filled Capsule Implosions on the National Ignition Facility

Here, the application of an external 26 Tesla axial magnetic field to a D 2 gas-filled capsule indirectly driven on the National Ignition Facility is observed to increase the ion temperature by 40% and the neutron yield by a factor of 3.2 in a hot spot with areal density and temperature approaching what is required for fusion ignition. The improvements are determined from energy spectral measurements of the 2.45 MeV neutrons from the D(d, n) 3 He reaction, and the compressed central core B field is estimated to be ~4.9 kT using the 14.1 MeV secondary neutrons from the D(T, n) 4 He reactions. The experiments use a 30 kV pulsed-power system to deliver a ~ 3 μs current pulse to a solenoidal coil wrapped around a novel high-electrical-resistivity AuTa 4 hohlraum. Radiation magnetohydrodynamic simulations are consistent with the experiment

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Zwicky Transient Facility: System Overview, Performance, and First Results

The Zwicky Transient Facility (ZTF) is a new optical time-domain survey that uses the Palomar 48 inch Schmidt telescope. A custom-built wide-field camera provides a 47 deg ^(2) field of view and 8 s readout time, yielding more than an order of magnitude improvement in survey speed relative to its predecessor survey, the Palomar Transient Factory. We describe the design and implementation of the camera and observing system. The ZTF data system at the Infrared Processing and Analysis Center provides near-real-time reduction to identify moving and varying objects. We outline the analysis pipelines, data products, and associated archive. Finally, we present on-sky performance analysis and first scientific results from commissioning and the early survey. ZTF’s public alert stream will serve as a useful precursor for that of the Large Synoptic Survey Telescope.

Eric C. Bellm↗

Fluorescence imaging of individual ions and molecules in pressurized noble gases for barium tagging in 136Xe

Abstract The imaging of individual Ba 2+ ions in high pressure xenon gas is one possible way to attain background-free sensitivity to neutrinoless double beta decay and hence establish the Majorana nature of the neutrino. In this paper we demonstrate selective single Ba 2+ ion imaging inside a high-pressure xenon gas environment. Ba 2+ ions chelated with molecular chemosensors are resolved at the gas-solid interface using a diffraction-limited imaging system with scan area of 1 × 1 cm 2 located inside 10 bar of xenon gas. This form of microscopy represents key ingredient in the development of barium tagging for neutrinoless double beta decay searches in 136 Xe. This also provides a new tool for studying the photophysics of fluorescent molecules and chemosensors at the solid-gas interface to enable bottom-up design of catalysts and sensors.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A Sobering Examination of the Feasibility of Aqueous Aluminum Batteries

Recent reports on aqueous aluminum (Al) batteries boast encouraging metrics including high energy density, nonflammability, and low raw material cost. However, the poorly understood solvation environment around the trivalent aluminum ions (Al3+) raises uncertainty regarding their feasibility. Furthermore, the corrosiveness of the acidic solutions and degree of hydration of aluminum trifluoromethanesulfonate (Al(OTf)3) salt is routinely mischaracterized. This study provides a rigorous examination of aqueous Al electrolytes, with the first compelling evidence for a dynamic octahedral solvation structure around Al3+ dominated by labile water and OH-, without Al-OTf contact ion pairs, at high concentrations. This solvation behavior and the concomitant electrostatic hydrolysis differs greatly from previously reported water-in-salt electrolytes, and occurs due to the high charge density of the Lewis acidic Al3+. Nuclear magnetic resonance spectroscopy and other physicochemical measurements quantitatively reveal how species activity evolves with concentration. The high proton activity observed in transport and electrochemical measurements constitutes a prohibitive barrier to the feasibility of rechargeable aluminum batteries with aqueous electrolyte.

Pastel, Glenn R.↗

The luminous, slow-rising orphan afterglow AT2019pim as a candidate moderately relativistic outflow

ABSTRACT Classical gamma-ray bursts (GRBs) have two distinct emission episodes: prompt emission from ultrarelativistic ejecta and afterglow from shocked circumstellar material. While both components are extremely luminous in known GRBs, a variety of scenarios predict the existence of luminous afterglow emission with little or no associated high-energy prompt emission. We present AT 2019pim, the first spectroscopically confirmed afterglow with no observed high-energy emission to be identified. Serendipitously discovered during follow-up observations of a gravitational-wave trigger and located in a contemporaneous TESS sector, it is hallmarked by a fast-rising ($t \approx 2$ h), luminous ($M_{\rm UV,peak} \approx -24.4$ mag) optical transient with accompanying luminous X-ray and radio emission. No gamma-ray emission consistent with the time and location of the transient was detected by Fermi-GBM or by Konus, placing constraining limits on an accompanying GRB. We investigate several independent observational aspects of the afterglow in the context of constraints on relativistic motion and find all of them are consistent with an initial Lorentz factor of $\Gamma _0 \approx$ 10–30 for the on-axis material, significantly lower than in any well-observed GRB and consistent with the theoretically predicted ‘dirty fireball’ scenario in which the high-energy prompt emission is stifled by pair production. However, we cannot rule out a structured jet model in which only the line-of-sight material was ejected at low-$\Gamma$, off-axis from a classical high-$\Gamma$ jet core, and an on-axis GRB with below-average gamma-ray efficiency also remains a possibility. This event represents a milestone in orphan afterglow searches, demonstrating that luminous optical afterglows lacking detected GRB counterparts can be identified and spectroscopically confirmed in real time.

Perley, Daniel A. (ORCID:0000000184721996)↗

Study on the Carbon Nanostructures for Nanosized Si Electrodes

Silicon (Si) has been considered as a next-generation anode material due to natural abundance, low operating potential (<0.5 V vs. Li/Li+), and high theoretical specific capacity of 4200 mAh g-1.[1] However, the electrochemical alloying reaction of Si involves large volume changes of 400% during lithiation and delithiation, causing cracking and pulverization of Si.[1] In addition, solid electrolyte interface (SEI) of Si anode experiences constant changes due to unstable SEI reactivity.[2] Considerable efforts have been made to design nanostructured Si materials to address the issues because nanostructuring can relieve the mechanical strain.[3] However, when compared to micrometer-sized active materials having sufficient electrolyte pathway through interparticle space, the nanoparticle (NP)-based electrodes tend to be densely packed. As mass loading is higher and electrode is thicker, ion transport issue can become more severe in the densely packed electrodes.[4] In this work, we will present studies on engineered porosity impacts performance in Si NP electrodes by altering carbon nanostructures. We explore the extreme limit of effectively non-porous electrodes using quasi-spherical, Si NPs, which result in densely packed electrodes when slurry is prepared with conventional carbon black. We engineer porosity using carbon nanostructures including multi-walled carbon nanotubes and carbon nanorods in place of conventional carbon black to create pore structure in Si NP-based electrodes. These experiments provide a correlation between mass loading, porosity and silicon utilization in Si NP-based electrodes. References: [1] C. K. Chan, H. Peng, G. Liu, K. Mcllwrath, X. F. Zhang, R. A. Huggins, Y. Cui, "High-performance lithium battery anodes using silicon nanowires", Nat. Nanotechnol., 2008, 3, 31, [2] J. D. McBrayer, M.-T. F. Rodrigues, M. C. Schulze, D. P. Abraham, C. A. Apblett, I. Bloom, G. M. Carroll, A. M. Coclasure, C. Fang, K. L. Harrison, G. Liu, S. D. Minteer, N. R. Neale, G. M. Veith, C. S. Johnson, J. T. Vaughey, A. K. Burrel, B. Cunningham, "Calendar aging of silicon-containing batteries", Nat. Energy, 2021, 6, 1164, [3] H. Wu, G. Zheng, N. Liu, T. J. Carney, Y. Yang, Y. Cui, "Engineering Empty space between Si Nanoparticles for Lithium-Ion Battery Anodes", Nano Lett., 2012, 12, 904, [4] X. Zhang, Z. Ju, Y. Zhu, K. J. Takeuchi, E. S. Takeuchi, A. C. Marschilok, G. Yu, "Multiscale Understanding and Architecture Design of High Energy/Power Lithium-Ion Battery Electrodes", Adv. Energy Mater., 2021, 11, 2000808

carbon nanostructure↗

The Atacama Cosmology Telescope: A Catalog of >4000 Sunyaev–Zel’dovich Galaxy Clusters

Here, we present a catalog of 4195 optically confirmed Sunyaev–Zel’dovich (SZ) selected galaxy clusters detected with signal-to-noise ratio >4 in 13,211 deg 2 of sky surveyed by the Atacama Cosmology Telescope (ACT). Cluster candidates were selected by applying a multifrequency matched filter to 98 and 150 GHz maps constructed from ACT observations obtained from 2008 to 2018 and confirmed using deep, wide-area optical surveys. The clusters span the redshift range 0.04 < z < 1.91 (median z = 0.52). The catalog contains 222 z > 1 clusters, and a total of 868 systems are new discoveries. Assuming an SZ signal versus mass-scaling relation calibrated from X-ray observations, the sample has a 90% completeness mass limit of M 500 c > 3.8 × 10 14 M ⊙ , evaluated at z = 0.5, for clusters detected at signal-to-noise ratio >5 in maps filtered at an angular scale of 2.'4. The survey has a large overlap with deep optical weak-lensing surveys that are being used to calibrate the SZ signal mass-scaling relation, such as the Dark Energy Survey (4566 deg 2 ), the Hyper Suprime-Cam Subaru Strategic Program (469 deg 2 ), and the Kilo Degree Survey (825 deg 2 ). We highlight some noteworthy objects in the sample, including potentially projected systems, clusters with strong lensing features, clusters with active central galaxies or star formation, and systems of multiple clusters that may be physically associated. The cluster catalog will be a useful resource for future cosmological analyses and studying the evolution of the intracluster medium and galaxies in massive clusters over the past 10 Gyr.

79 ASTRONOMY AND ASTROPHYSICS↗

Trap-assisted Auger-Meitner recombination in GaN p-i-n diodes

Most properties of semiconductor devices are dominated by shallow impurities. However, deep defects often play an important role, for instance, in recombination processes or high field transport. While a variety of techniques are available to assess the density and energy levels of impurities, other properties, such as the recombination mechanisms of the defects, escape observation. We report on the direct measurement of hot electrons generated by trap-assisted Auger-Meitner recombination (TAAR) in GaN p-i-n diodes. By performing electron emission spectroscopy (EES) on diodes with surfaces activated to negative electron affinity by cesium, we observe the expected overflow electrons of p-i-n diodes under low current injection. However, when operating the devices at higher current densities, as low as ∼25 A/c⁢m 2 , we measure the emission of high-energy electrons. At variance with the observed hot electrons in light-emitting diodes (LEDs) using EES, the hot electrons generated in p-i-n diodes at our tested currents cannot be from eeh Auger-Meitner recombination due to the diodes' significantly lower carrier densities compared to those in LEDs. During our measurements, we observe the emission of accumulated electrons with energies ∼0.42 eV, ∼0.99 eV, ∼1.43 eV, and ∼2.32 eV above the conduction-band minimum (CBM) at various bias conditions, suggesting the existence of conduction-band features in GaN at these energies where electrons can be long-lived, such as satellite-valley minima and inflection points. We also measure incompletely relaxed hot electrons approaching energies 1.97 ± 0.13 eV and 2.94 ± 0.13 eV above the CBM, as the diodes are biased to high currents, suggesting at least some of the TAAR partaking defects have an energy level ≳1.97 eV and ≳2.94 eV away from either the conduction or valence band edges. Additionally, at our highest operating currents, we measure hot electrons with energies 3.28 ± 0.13 eV above the CBM, providing direct evidence of TAAR processes involving shallow impurities. This unexpected observation of TAAR in GaN p-i-n diodes spotlights the importance of further studies of defects in GaN and the necessity to incorporate the multi-phonon emission, radiative, and TAAR capture steps of defect-assisted recombination cycles into device modeling. Furthermore, this experiment demonstrates the applicability of the simplest semiconductor structures, p-i-n diodes, as a test bed to study the rich recombination physics of semiconductor materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Atacama Cosmology Telescope: DR4 maps and cosmological parameters

In this paper, we present new arcminute-resolution maps of the Cosmic Microwave Background temperature and polarization anisotropy from the Atacama Cosmology Telescope, using data taken from 2013–2016 at 98 and 150 GHz. The maps cover more than 17,000 deg 2 , the deepest 600 deg 2 with noise levels below 10µK-arcmin. We use the power spectrum derived from almost 6,000 deg 2 of these maps to constrain cosmology. The ACT data enable a measurement of the angular scale of features in both the divergence-like polarization and the temperature anisotropy, tracing both the velocity and density at last-scattering. From these one can derive the distance to the last-scattering surface and thus infer the local expansion rate, H 0 . By combining ACT data with large-scale information from WMAP we measure H 0 = 67.6±1.1 km/s/Mpc, at 68% confidence, in excellent agreement with the independently-measured Planck satellite estimate (from ACT alone we find H 0 = 67.9 ± 1.5 km/s/Mpc). The ΛCDM model provides a good fit to the ACT data, and we find no evidence for deviations: both the spatial curvature, and the departure from the standard lensing signal in the spectrum, are zero to within 1σ; the number of relativistic species, the primordial Helium fraction, and the running of the spectral index are consistent with ΛCDM predictions to within 1.5–2.2σ. We compare ACT, WMAP, and Planck at the parameter level and find good consistency; we investigate how the constraints on the correlated spectral index and baryon density parameters readjust when adding CMB large-scale information that ACT does not measure. The DR4 products presented here will be publicly released on the NASA Legacy Archive for Microwave Background Data Analysis.

60 APPLIED LIFE SCIENCES↗

The Atacama Cosmology Telescope: DR4 maps and cosmological parameters

We present new arcminute-resolution maps of the Cosmic Microwave Background temperature and polarization anisotropy from the Atacama Cosmology Telescope, using data taken from 2013{2016 at 98 and 150 GHz. The maps cover more than 17,000 deg(^2), the deepest 600 deg(^2) with noise levels below 10µK-arcmin. We use the power spectrum derived from almost 6,000 deg(^2) of these maps to constrain cosmology. The ACT data enable a measurement of the angular scale of features in both the divergence-like polarization and the temperature anisotropy, tracing both the velocity and density at last-scattering. From these one can derive the distance to the last-scattering surface and thus infer the local expansion rate, H0. By combining ACT data with large-scale information from WMAP we measure H0 = 67:6±1:1 km/s/Mpc, at 68% confidence, in excellent agreement with the independently measured Planck satellite estimate (from ACT alone we find H0 = 67:9± 1:5 km/s/Mpc). The ΛCDM model provides a good fit to the ACT data, and we find no evidence for deviations: both the spatial curvature, and the departure from the standard lensing signal in the spectrum, are zero to within 1σ; the number of relativistic species, the primordial Helium fraction, and the running of the spectral index are consistent with ΛCDM predictions to within 1.5{2.2σ. We compare ACT, WMAP, and Planck at the parameter level and find good consistency; we investigate how the constraints on the correlated spectral index and baryon density parameters readjust when adding CMB large-scale information that ACT does not measure. The DR4 products presented here will be publicly released on the NASA Legacy Archive for Microwave Background Data Analysis.

Simone Aiola↗

Soluble Organic Matter (SOM) analysis of the Hayabusa2 samples: The first results

The Hayabusa2 spacecraft successfully collected the surface and possible sub-surface materials of the asteroid 162173 Ryugu. Ryugu is a C-type asteroid characterized by a low-albedo surface probably consisting of hydrous minerals and carbonaceous materials. [1] The direct optical and spectral analysis of the returned samples indicates that Ryugu material is dominated by hydrous carbonaceous chondrite-like matter (similar to CI chondrites) [2]. Since carbonaceous chondrites have generally yielded various types of organic matter, the collected Ryugu grains are expected to contain diverse types of organic compounds including bio-related molecules. The occurrence of organic compounds in the Ryugu surface will provide clues to the evolution of prebiotic molecules and their preservations associated with aqueous alteration of the primitive asteroid. The initial analysis of soluble organic matter (SOM) of the Hayabusa2-returned samples has been performed by an international team consisting of 32 members. Because the sample amount available for comprehensive SOM analyses is limited, and because the SOM is expected to be present as a complex mixture of various types of organic compounds with very small concentrations of each compound, high-sensitivity and high-resolution analytical techniques have been developed using carbonaceous meteorites [e.g. 3]. Two aggregate samples of the Ryugu grains (A106 and C107) were allocated for the solvent extractions and bulk carbon (C), hydrogen (H), nitrogen (N), sulfur (S) and oxygen (O) measurements. The A106 sample was collected during the 1st sampling in February 2019 and the C107 sample was collected during the 2nd sampling in July 2019 after the Small Carry Impactor (SCI) operation. They consist mainly of particles smaller than 1 mm in diameter, and each sample mass was 38-39 mg. They were firstly investigated spectroscopically in the near infrared wavelength range by the Stone Team prior to the solvent extractions. Other small grains (A0080 and C0057) were also allocated for this study to investigate the spatial distribution of organic compounds on the sample surface. The extraction and analytical measurements implemented by the SOM Team are summarized in Figure 1. Each powder sample was extracted sequentially with non-polar to polar solvents, i.e., hexane, dichloromethane (DCM), methanol (MeOH) and H2O, for non-targeted analysis to reveal the compound composition. Each solvent extract was analyzed by solution state nuclear magnetic resonance (NMR) spectroscopy [4], Fourier transform- ion cyclotron resonance/mass spectrometry (FT-ICR/MS) with ESI and APPI ionization [5] and by high-resolution mass spectroscopy using Orbitrap MS coupled with nano-liquid chromatography (nanoLC/Orbitrap MS) [6], and using two dimensional gas chromatography/mass spectrometry (GC×GC/MS). The extracted residues were passed to the Chemistry Team for further inorganic element analysis. The other powder sample was subjected to the hot water extraction for amino acid analyses including chiral isomer separation, which was performed by three-dimensional (3D) high-performance liquid chromatography (HPLC) with high-sensitivity fluorescence detection (FD) [7] and by HPLC/FD coupled with quadrupole-time of flight/mass spectrometry (QToF/MS) [8]. After the hot water extraction, the residue was split into two halves. One half was further extracted with hydrochloric acid (HCl) to analyze for amino acids in bound-form. The other half was sequentially extracted with DCM/MeOH (1/1) to analyze semi-polar compounds such as polycyclic aromatic hydrocarbons (PAHs) by GC/MS, followed by further extraction with formic acid to analyze polar heterocyclic compounds, and subsequent extraction with HCl to detect bound-form polar compounds. The extracted residues were passed to the IOM Team for the analysis of insoluble organic matter (IOM). Compound-specific stable isotope analyses will be performed using GC/combustion/isotope ratio mass spectrometry (GC/C/IRMS) if the compound concentration is high enough to enable such an isotopic measurement. All extraction procedures were performed on an ISO 6 (Class 100) clean bench inside an ISO 5 (Class 1000) clean room. Baked serpentine powder was also analyzed as a procedural blank. In situ organic compound analysis with the molecular imaging was performed using desorption electrospray ionization (DESI) equipped with Orbitrap MS [9, 10], followed by spatial imaging of organic compounds using ToF/secondary ion mass spectrometry (ToF/SIMS) [11]. The bulk chemical and isotopic compositions of CNS and HO were determined using nano-elemental analysis/isotope ratio mass spectrometry (nanoEA/IRMS) [12] and EA/pyrolysis/IRMS, respectively. We have identified a variety of indigenous organic compounds in the extracts of both A106 and C107 samples. The Ryugu grains host organic molecules under the high-vacuum and cosmic-ray irradiation environment of the asteroid surface. The analysis of extracted molecules is in progress, and the first results will be presented at the symposium.

Hiroshi Naraoka↗

Measurement of the Full Shape of the Thermal Sunyaev–Zel’dovich Power Spectrum from the South Pole Telescope and Herschel–SPIRE Observations

We present a measurement of the full shape of the power spectrum of the thermal Sunyaev–Zel’dovich (tSZ) effect down to arcminute scales using cosmic microwave background (CMB) data from the South Pole Telescope (SPT) over a roughly 100 deg 2 field. The analysis incorporates data from the 2019–2020 seasons of the SPT-3G survey in bands centered at 95, 150, and 220 GHz; from the full SPTpol dataset at 150 GHz; and from the Herschel–SPIRE survey in bands centered at 600 and 857 GHz. We combine data from all the above bands using linear combination (LC) techniques to produce a tSZ or Compton-y map. We modify the LC weights to produce multiple versions of the Compton-y map, including minimum-variance (MV) and foreground-minimized (-min) maps. We measure the auto- and cross-power spectra of a subset of these maps in the range ℓ ∈ [500, 5000]. While this power spectrum includes contributions from signals other than tSZ, we present numerous checks to show that the most challenging foreground signal, the cosmic infrared background (CIB), is much lower than the desired tSZ signal in the scales of interest in this work. The final tSZ power spectrum is measured at 9.3σ with both the MV and CIB-min maps. Our results are consistent with those reported in other CMB surveys across the literature. Using the difference in the tSZ power spectrum from the MV and CIB-min maps, we reconstruct the scale-dependent tSZ–CIB cross correlation $ρ^{\textrm{tSZ}}_{ℓ}$ x CIB, finding 3.1σ evidence for a nonzero correlation coefficient that is positive on large scales and approaches zero for ℓ > 2500. This result represents the deepest tSZ maps ever produced and provides new constraints that can help refine astrophysical feedback mechanisms and models of the intracluster medium.

Raghunathan, S. [Univ. of California, Davis, CA (U↗

Key metrics of progress in the NIF ignition implosions and future challenges on the path to higher yields

Successful demonstration of an implosion that meets the physics metrics for ignition on the National Ignition Facility (NIF) in August 2021 and demonstration of target energy gain G > 1 in December 2022 represented the culmination of more than a decade of research on the NIF. An in-depth analysis of the key ignition metrics achieved on the NIF over the past decade shows sustained progress toward identifying and mitigating degradation effects. Ignition implosions on the NIF have progressed from early experiments whose compressed fuel conditions were degraded by a factor of 10–20 below the ignition threshold with yields of only 1%–2% of the laser energy, to current experiments that significantly exceed the ignition threshold and in the best experiments achieve yields greater than twice the laser energy. It is very likely that NIF can get more than 20 MJ of yield and possibly 50–70 MJ yields when fully optimized at an ultraviolet laser energy of 2.6 MJ following the completion of the NIF Extended Yield Capability Project. Achieving these higher yields will also require improvements to capsules at larger size and possibly with alternate materials, as well as an improved understanding of hohlraum and capsule physics. Now that NIF has achieved ignition, the design of a Next Generation High Energy Density Facility that could achieve the National Nuclear Security Administration long-term goal of substantially higher yields than the NIF can proceed with a more confident physics base. We evaluate these opportunities including possible applications for inertial fusion energy and likely challenges to achieving this level of performance over the next decade.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DESI DR2 results. II. Measurements of baryon acoustic oscillations and cosmological constraints

We present baryon acoustic oscillation (BAO) measurements from more than 14 million galaxies and quasars drawn from the Dark Energy Spectroscopic Instrument (DESI) Data Release 2 (DR2), based on three years of operation. For cosmology inference, these galaxy measurements are combined with DESI Lyman-𝛼 forest BAO results presented in a companion paper (M. Abdul-Karim et al., companion paper, Phys. Rev. D 112, 083514 2025.). The DR2 BAO results are consistent with DESI DR1 and the Sloan Digital Sky Survey, and their distance-redshift relationship matches those from recent compilations of supernovae (SNe) over the same redshift range. The results are well described by a flat Λ cold dark matter (Λ⁢CDM) model, but the parameters preferred by BAO are in mild, 2.3⁢𝜎 tension with those determined from the cosmic microwave background (CMB), although the DESI results are consistent with the acoustic angular scale 𝜃 * that is well measured by Planck. This tension is alleviated by dark energy with a time-evolving equation of state parametrized by 𝑤0 and 𝑤𝑎, which provides a better fit to the data, with a favored solution in the quadrant with 𝑤 0 >−1 and 𝑤 𝑎 <0. This solution is preferred over Λ ⁢CDM at 3.1⁢𝜎 for the combination of DESI BAO and CMB data. When also including SNe, the preference for a dynamical dark energy model over Λ⁢ CDM ranges from 2.8 − 4.2⁢𝜎 depending on which SNe sample is used. We present evidence from other data combinations which also favor the same behavior at high significance. From the combination of DESI and CMB we derive 95% upper limits on the sum of neutrino masses, finding ∑𝑚 𝜈 < 0.064 eV assuming Λ ⁢CDM and ∑𝑚 𝜈 < 0.16 eV in the 𝑤0⁢𝑤𝑎 model. Unless there is an unknown systematic error associated with one or more datasets, it is clear that Λ⁢ CDM is being challenged by the combination of DESI BAO with other measurements and that dynamical dark energy offers a possible solution.

Baryon acoustic oscillations↗