Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thermoplastic composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Modeling of Response of Thermoplastic Composites Under High Energy Impact

This work investigates the response of a thermoplastic panel under high energy ballistic impact. The composite material system is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK3). Several high energy dynamic impact tests were performed where an aluminum projectile impacted various panels at different impact velocities. For this work, the test performed at an impact velocity of 73.2 m/s was investigated. The projectile rebounded upon impact, and the damage to the panel was characterized through ultrasonic and CT-scanning. Response of the panel under impact and the associated damage is discussed. Numerical simulation of the impact process was performed using the LS-DYNA® computer code [1] with a new material model MAT_COMPOSITE_DAMAGE_DGD (MAT 299), a modification over MAT 261 material model in terms of an improved representation of damage coupling and additional capability for strain rate effects. Delaminations were modeled using cohesive zone contact formulation in LS-DYNA®, wherein the mixed-mode fracture is captured via the Benzegaggh-Kenane (B-K) mode-dependent fracture energy interpolation law. Simulation of this impact test demonstrates a good match of results in terms of panel deflection and panel-projectile interactions. The overall extent of delaminations was under-predicted by the simulation. This work forms the basis to model tests performed at higher velocities, involving projectile penetration of panel.

Composite Materials↗
NASA NTRSDate not supplied

Thermal Response of Thermoplastic Composite Tape During In-situ Consolidation Automated Fiber Placement Using a Laser Heat Source

Composite materials have tremendous potential in the design and manufacture of commercial aircraft due to their high strength-to-weight and stiffness-to-weight properties. However, the use of composite materials is currently limited by high cost and long manufacturing time. The National Aeronautics and Space Administration (NASA) initiated the Hi-rate Composite Aircraft Manufacturing (HiCAM) project to investigate promising composite processing technologies with a goal of vastly improving composite commercial aircraft manufacturing rate (4-6x faster than current production rates). Laser assisted automated fiber placement (AFP) of thermoplastics is a key technology that could increase speed of composite manufacturing, but the technology has not been fully developed. In-situ consolidation AFP of thermoplastics (ICAT) could reduce time and cost even further by eliminating the time and equipment required for post-consolidation. In this work, the thermal response of laser heated ICAT was investigated using forward looking infrared (FLIR) and embedded thermocouples (TCs) to better understand fusion between layers (autohesion). Detailed explanation of the algorithm to combine FLIR and TC data will be presented. In addition, the effect of robot speed on time above melting temperature was quantified.

Laser Heating↗
NASA NTRSDate not supplied

High Energy Dynamic Impact Testing of APC AS4D/PEKK-FC and TC1225 LMPAEK T700G Thermoplastic Composite Materials

High energy dynamic impact tests were conducted on AS4/PEKK and TC1225 LMPAEK T700G thermoplastic quasi-isotropic laminated tape composite panels. The primary objective was to provide data for evaluation of computational composite impact models. Measurements include transient deformations, pre- and post-test characterization of delamination and energy threshold for onset of delamination and onset of penetration. Empirical results indicate an approximately 50% increase in penetration threshold velocity and over 100% increase in penetration energy threshold for the TC1225 LMPAEK T700G composite compared to the AS4/PEKK composite. The velocity required to produce NDE-detectable delamination in the TC1225 LMPAEK T700G composite was roughly twice that for the AS4/PEKK composite. Results will be compared with those from a thermoset composite system with a similar architecture. Because of differences in the chemical structure of the two resins, differences in the impact response are to be expected.

Impact↗
NASA NTRS1992

Characterization of damage modes in impacted thermoset and thermoplastic composites

Composite materials remain extremely vulnerable to out-of-plane impact loads, which may lead to severe losses in strength and stiffness. Impact induced damage is often a complex mixture of transverse cracks, delaminations and fiber failures. An experimental investigation was undertaken to quantify damage tolerance and resistance in composite materials impacted using the drop-weight method. Tests were conducted on laminates of several different carbon-fiber composite systems such as epoxies, modified epoxies, and amorphous and semicrystalline thermoplastics. In this paper, impacted composite specimens have been examined using destructive and nondestructive techniques to establish the characteristic damage states. Specifically, optical microscopy, ultrasonic and scanning electron microscopy techniques have been used to identify impact induced damage mechanisms. Damage propagation during post impact compression was also studied.

Srinivasan, K.↗
NASA NTRS1984

Solvent Resistant Thermoplastic Composite Matrices

The following approaches improved the solvent resistance and raised the Tg of thermoplastics: end-capping aligomers with ethynyl groups; incorporating ethynyl groups pendent along the polymer chain; and correcting polymers containing pendent ethynyl groups with a low molecular weight diethynyl compound. The following conclusions were reached: (1) film and composite properties off an ethynyl-terminated sulfone were better than those of UDEL (trademark); (2) fracture energy of an ethynyl-terminated sulfone was lower than that of UDEL (trademark); (3) residual palladium in the cured ethynyl-terminated sulfone lower the thermooxidative stability of the cured resin; (4) the properties of a phenoxy resin were altered considerably by placing pendent ethynyl groups along the polymer chain; and (5) property trade-offs must be considered when thermoplastics are modified via reactant groups.

Hergenrother, P. M.↗
NASA NTRS1984

Thermoplastic composite matrices with improved solvent resistance

In order to improve solvent resistance of aromatic thermoplastic polymers, ethynyl-terminated aromatic sulfone polymers (ETS), sulfone/ester polymers (SEPE) containing pendent ethynyl groups, and phenoxy resin containing pendent ethynyl groups are synthesized. Cured polysulfones and phenoxy resins containing ethynyl groups on the ends or pendent on the molecules exhibited systematic behavior in solvent resistance, film flexibility, and toughness as a function of crosslink density. The film and composite properties of a cured solvent-resistant ETS were better than those of a commercially available solvent sensitive polysulfone. The study was part of a NASA program to better understand the trade-offs between solvent resistance, processability and mechanical properties which may be useful in designing composite structures for aerospace vehicles.

Hergenrother, P. M.↗
NASA NTRSDate not supplied

Verification and Validation of Progressive Damage and Failure Analysis Methods for Intralaminar Failure Modes in Thermoplastic Composites

Current progressive damage and failure analysis (PDFA) methods were developed around thermoset material systems and their physical behavior. However, the applicability of these analysis methods has not been evaluated for use in modeling thermoplastic material systems. As part of the Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project sponsored by NASA, intralaminar failure characterization was completed on a thermoplastic material system, AS4D/PEKK-FC, with off-axis tension (OAT) and off-axis compression (OAC) testing. The experiments were able to capture matrix non-linear shear behavior and the failure envelope of the material system. Two PDFA methods, LS-DYNA MAT299 and NASA’s CompDam-DGD, were then employed to simulate individual coupon behavior and simulation results were compared to published verification and validation guidelines from the CMH-17 crashworthiness working group. The results found that the two modeling methods provided suitable representation of material behavior of thermoplastics.

PDFA↗
NASA NTRSDate not supplied

Verification and Validation of Progressive Damage and Failure Analysis Methods for Intralaminar Failure Modes in Thermoplastic Composites

Current progressive damage and failure analysis (PDFA) methods were developed around thermoset material systems and their physical behavior. However, the applicability of these analysis methods has not been evaluated for use in modeling thermoplastic material systems. As part of the Hi-Rate Composite Aircraft Manufacturing (HiCAM) Project sponsored by NASA, intralaminar failure characterization was completed on a thermoplastic material system, AS4D/PEKK-FC, with off-axis tension (OAT) and off-axis compression (OAC) testing. The experiments were able to capture matrix non-linear shear behavior and the failure envelope of the material system. Two PDFA methods, LS-DYNA MAT299 and NASA’s CompDam-DGD, were then employed to simulate individual coupon behavior and simulation results were compared to published verification and validation guidelines from the CMH-17 crashworthiness working group. The results found that the two modeling methods provided suitable representation of material behavior of thermoplastics.

PDFA↗
NASA NTRS1987

Interfacial strength development in thermoplastic resins and fiber-reinforced thermoplastic composites

An experimental program to develop test methods to be used to characterize interfacial (autohesive) strength development in polysulfone thermoplastic resin and graphite-polysulfone prepreg during processing is reported. Two test methods were used to examine interfacial strength development in neat resin samples. These included an interfacial tension test and a compact tension (CT) fracture toughness test. The interfacial tensile test proved to be very difficult to perform with a considerable amount of data scatter. Thus, the interfacial test was discarded in favor of the fracture toughness test. Interfacial strength development was observed by measuring the refracture toughness of precracked compact tension specimens that were rehealed at a given temperature and contact time. The measured refracture toughness was correlated with temperature and contact time. Interfacial strength development in graphite-polysulfone unidirectional composites was measured using a double cantilever beam (DCB) interlaminar fracture toughness test. The critical strain energy release rate of refractured composite specimens was measured as a function of healing temperature and contact time.

Howes, Jeremy C.↗
DOE OSTI2024

Post-Deployment Characterization of Glass Fiber-Reinforced Thermoset and Thermoplastic Composite Tidal Turbine Blades

In 2021, the National Renewable Energy Laboratory (NREL) supported Verdant Power with the most successful tidal energy deployment in U.S. history. Three of their Gen5d 5 m turbines were deployed as part of the Roosevelt Island Tidal Energy project. Initially, the three rotors initially deployed were manufactured from glass fiber-reinforced epoxy composites. Midway through the deployment, one rotor was replaced with one manufactured at NREL. The new rotor utilized a novel infusible thermoplastic resin system. Since the deployment, one epoxy rotor and one thermoplastic rotor were returned to NREL for continued materials and manufacturing research. The two rotors underwent full-scale structural testing before being sectioned and cut into specimens for a variety of manufacturing quality tests, thermomechanical characterization, and evaluation of material performance in marine environments to understand the key differences between the fiberglass-reinforced epoxy and Elium composites used for the respective rotors. Matrix burn-off tests showed that the Elium blades had a considerably higher fiber volume fraction compared to the epoxy blades (61% vs. 49%). Environmental aging of the specimens showed that the epoxy laminates absorbed more water over the conditioning period; however, it was determined that the Elium laminates had higher diffusion coefficients, so they initially absorbed water faster. Finally, one full epoxy blade and one full Elium blade were conditioned at ambient temperatures for up to 11 months, while periodic mass measurements were taken. The datasets were extrapolated to assume a full 20-year operational life span, and it was determined that the blades would not reach full saturation during that time span.

composite manufacturing↗
DOE OSTI2024

Post-Deployment Characterization of Glass Fiber-Reinforced Thermoset and Thermoplastic Composite Tidal Turbine Blades

In 2021, the National Renewable Energy Laboratory (NREL) supported Verdant Power with the most successful tidal energy deployment in U.S. history. Three of their Gen5d 5 m turbines were deployed as part of the Roosevelt Island Tidal Energy project. Initially, the three deployed rotors were manufactured from glass fiber-reinforced epoxy composites. Midway through the deployment, one rotor was replaced with one manufactured at NREL. The new rotor utilized a novel infusible thermoplastic resin system (Elium from Arkema). Since the deployment, one epoxy rotor and one thermoplastic rotor were returned to NREL for continued materials and manufacturing research. The two rotors underwent full-scale structural testing before being sectioned and cut into specimens for a variety of manufacturing quality tests, thermomechanical characterization, and evaluation of material performance in marine environments to understand the key differences between the fiberglass-reinforced epoxy and Elium composites used for the respective rotors. Matrix burn-off tests showed that the Elium blades had a considerably higher fiber volume fraction compared to the epoxy blades (61% vs. 49%). Environmental aging of the specimens showed that the epoxy laminates absorbed more water over the conditioning period; however, it was determined that the Elium laminates had higher diffusion coefficients, so they initially absorbed water faster. Finally, one full epoxy blade and one full Elium blade were conditioned at ambient temperatures for up to 11 months, while periodic mass measurements were taken. The datasets were extrapolated to assume a full 20-year operational life span, and it was determined that the blades would not reach full saturation during that time span.

composite manufacturing↗
NASA NTRS1993

Establishing the relationship between manufacturing and component performance in stretch formed thermoplastic composites

Flexible manufacturing methods are needed to reduce the cost of using advanced composites in structural applications. One method that allows for this is the stretch forming of long discontinuous fiber materials with thermoplastic matrices. In order to exploit this flexibility in an economical way, a thorough understanding of the relationship between manufacturing and component performance must be developed. This paper reviews some of the recent work geared toward establishing this understanding. Micromechanics models have been developed to predict the formability of the material during processing. The latest improvement of these models includes the viscoelastic nature of the matrix and comparison with experimental data. A finite element scheme is described which can be used to model the forming process. This model uses equivalent anisotropic viscosities from the micromechanics models and predicts the microstructure in the formed part. In addition, structural models have been built to account for the material property gradients that can result from the manufacturing procedures. Recent developments in this area include the analysis of stress concentrations and a failure model each accounting for the heterogeneous material fields.

Santare, Michael H.↗
DOE OSTI2024

Post-Deployment Characterization of Glass Fiber-Reinforced Thermoset and Thermoplastic Composite Tidal Turbine Blades: Preprint

In 2021, the National Renewable Energy Laboratory (NREL) supported Verdant Power with the most successful tidal energy deployment in U.S. history. Three of their tidal turbines were deployed as part of the Roosevelt Island Tidal Energy project. Initially, the three rotors were manufactured from glass fiber-reinforced epoxy composites. Midway through the deployment, one rotor was replaced with one manufactured at NREL. Instead, it was infused with a novel, infusible thermoplastic resin system. Since the deployment, one epoxy rotor and one thermoplastic rotor were returned to NREL for continued materials and manufacturing research. The two rotors underwent full-scale structural testing before being sectioned and cut into specimens for a variety of manufacturing quality tests, thermos-mechanical characterization, and evaluation of material performance in marine environments, to understand the key differences between the fiberglass reinforced epoxy and Elium composites used for the respective rotors. Matrix burnoff tests showed that the Elium blades had a considerably higher fiber volume fraction compared to the epoxy blades (61% vs. 49%). Environmental aging of the specimens showed that the epoxy laminates absorbed more water over the conditioning period, however, it was determined that the Elium laminates had higher diffusion coefficients, so initially absorbed water faster. Finally, one full epoxy blade and one full Elium blade were conditioned at ambient temperatures for up to 11 months, while taking periodic mass measurements. The datasets were extrapolated out to assume a full 20 year operational life span and it was determined that the blades would not reach full saturation during that time span.

composite manufacturing↗
DOE OSTI2025

Improving adhesive bonding of short carbon fiber thermoplastic composites to aluminum alloys with a hybrid laser-plasma surface modification strategy

This study investigates hybrid laser–plasma surface modification strategies for metal–CFRTP (carbon-fiber-reinforced thermoplastic polymer) dissimilar joints to improve their bonding performance, in contrast to existing literature that mostly focuses on either plasma or laser treatment alone. By conducting double cantilever beam (DCB) tests on adhesively-bonded AA5052 and CFRPA66 (carbon-fiber-reinforced polyamide 66) joints, as an example of metal–CFRTP joints, it was found that laser engraving on the metal surface combined with plasma treatment on the CFRTP surface significantly improved the specific fracture energy of the joint by 187% and 31% compared to as-received and plasma-treated-only joints, respectively. However, the hybrid treatment of laser engraving and plasma on the investigated CFRTP surface did not improve the bonding performance of the joints. The underlying mechanisms related to hybrid laser-plasma surface modification strategies were further investigated by examining the surface and cross-sectional morphologies after DCB testing using microscopy. Computational modeling was performed to elucidate the interaction between grooves on the metal substrate and the CFRTP–adhesive interfacial bonding in metal–CFRTP joints. This study provides new insights into developing surface modification methods for achieving strong metal–CFRTP adhesive joints, aimed at lightweighting structural components in automotive, aerospace, and other applications.

Adhesive bonding↗
DOE OSTI2022

Mechanical Response and Processability of Wet-Laid Recycled Carbon Fiber PE, PA66 and PET Thermoplastic Composites

The interest in recycled carbon fiber (rCF) is growing rapidly and the supply chain for these materials is gradually being established. However, the processing routes, material intermediates and properties of rCF composites are less understood for designers to adopt them into practice. This paper provides a practical pathway for rCFs in conjunction with low cost and, for the most part, commodity thermoplastic resins, namely polyethylene (PE), polyamide 66 (PA66) and polyethylene terephthalate (PET). Industrially relevant wet-laid (WL) process routes have been adopted to produce mats using two variants of WL mats, namely (a) high speed wet-laid inclined wire to produce broad good ‘roll’ forms and (b) 3DEPTM process patented by Materials Innovation Technologies (MIT)-recycled carbon fiber (RCF), now Carbon Conversions, which involves mixing fibers and water and depositing the fibers on a water-immersed mold. These are referred to as ‘sheet’ forms. The produced mats were evaluated for their processing into composites as ‘fully consolidated mats’ and ‘non-consolidated’ as-produced mats. Comprehensive mechanical data in terms of tensile strength, tensile modulus and impact toughness for rCF C/PE, C/PA66 and C/PET are presented. The work is of high value to sustainable composite designers and modelers.

compression molding↗
DOE OSTI2020

Effect of 3D printing conditions on the micro- and macrostructure and properties of high-performance thermoplastic composites

Within the scope of extrusion based additive manufacturing, this chapter provides a review of the research in understanding the physical relationships between microstructure variables and macrostructure properties of high-performance thermoplastic polymers. The development of interlayer strength has been discussed based on the theory of inter-diffusion and re-entanglement of polymer chains at interface. The observations from the study in joining and direct-bonding of polymer surfaces provide insights into the mechanisms of the formation of interface between adjacent layers. Quantitative prediction of interfacial strength as a function of processing temperature and contact time is presented. The mechanisms that lead to reduced mechanical strength at the interface are discussed. The second half of the chapter outlined a set of printing conditions and their influence on structural properties.

Liu, Peng↗
DOE OSTI2023

Conductive overbraid of continuous fiber thermoplastic composite tows

Here, to meet the increasing demand for lightweight materials with multifunctional capabilities, a new high-rate manufacturing method and material system, referred to as M-TOW ® (multifunctional-tow) is introduced. Overbraiding is used to incorporate highly conductive wire onto the continuous fiber reinforced tow (M-TOW ® ), offering a solution for integrating thermal and electrical conductivity into hybrid-molded composite structures. The conductivity performance of different wire configurations are compared before and after forming the M TOW ® , measuring electrical conductivities up to 5.5 x 10 5 S / cm and thermal conductivities up to 21 W / mK. Results conclude that the integration of conductive wires into thermoplastic preforms is a viable means of expanding the functionality of lightweight, high strength composite structures.

3-dimensional reinforcement↗