SEARCH · Engineering Papers

Results for “TWIST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Subcooled freon-11 flow boiling in top-heated finned coolant channels with and without a twisted tape

An experimental study was conducted in top-heated finned horizontal tubes to study the effect of enhancement devices on flow boiling heat transfer in coolant channels. The objectives are to examine the variations in both the mean and local (axial and circumferential) heat transfer coefficients for circular coolant channels with spiral finned walls and/or spiral fins with a twisted tape, and improve the data reduction technique of a previous investigator. The working fluid is freon-11 with an inlet temperature of 22.2 C (approximately 21 C subcooling). The coolant channel's exit pressure and mass velocity are 0.19 M Pa (absolute) and 0.21 Mg/sq. ms, respectively. Two tube configurations were examined; i.e., tubes had either 6.52 (small pitch) or 4.0 (large pitch) fins/cm of the circumferential length (26 and 16 fins, respectively). The large pitch fins were also examined with a twisted tape insert. The inside nominal diameter of the copper channels at the root of the fins was 1.0 cm. The results show that by adding enhancement devices, boiling occurs almost simultaneously at all axial locations. The case of spiral fins with large pitch resulted in larger mean (circumferentially averaged) heat transfer coefficients, h sub m, at all axial locations. Finally, when twisted tape is added to the tube with large-pitched fins, the power required for the onset of boiling is reduced at all axial and circumferential locations.

Smith, Alvin↗

NASA NTRS1991

The resonant absorption of p-modes by sunspots with twisted magnetic fields

A simplified inhomogeneous sunspot model with an axial current (twisted magnetic field) is considered. The absorption of incoming acoustic modes in a narrow resonance layer inside the sunspot flux tube is investigated, and the energy loss is estimated. For nonaxisymmetric modes the results are consistent with previous calculations. However, contrary to previous work, it is demonstrated that the existence of an azimuthal component of the magnetic field can lead to significant absorption of even the axisymmetric modes. If the absorption rate calculated in this paper is used in conjunction with the observed wavelength dependence of the absorption coefficient, it is found that the sunspot flux tube must have significant twist in the subsurface layers. Furthermore, the presence of twist in the magnetic field leads to a natural explanation for the observed dependence on m, the azimuthal wave mode number, and the magnitude of the absorption coefficient can be accounted for in a self-consistent way.

Chitre, S. M.↗

NASA NTRS1992

Initiation of bipolar flows by magnetic field twisting in protostellar nebulae

A model is developed for the time-dependent twisting of an initial poloidal magnetic field threading a conducting protostellar disk. The region outside the disk is assumed to be filled, at least initially, with a low-density, force-free 'coronal' plasma. The differential rotation of the disk acts to twist the B field in the space outside the disk thus generating a toroidal magnetic field. In turn, the toroidal field acts to pinch the plasma and the poloidal field toward the system axis producing a collimated channel. This channel could facilitate the formation of bipolar flows. The magnitude and duration of the field twisting is expected to be limited by magnetohydrodynamic instability.

Newman, William I.↗

NASA NTRS1993

Experimental and analytical investigation of dynamic characteristics of extension-twist-coupled composite tubular spars

The results from a study aimed at improving the dynamic and aerodynamic characteristics of composite rotor blades through the use of extension-twist coupling are presented. A set of extension-twist-coupled composite spars was manufactured with four plies of graphite-epoxy cloth prepreg. These spars were noncircular in cross-section design and were therefore subject to warping deformations. Three different cross-sectional geometries were developed: D-shape, square, and flattened ellipse. Three spars of each type were fabricated to assess the degree of repeatability in the manufacturing process of extension-twist-coupled structures. Results from free-free vibration tests of the spars were compared with results from normal modes and frequency analyses of companion shell-finite-element models. Five global modes were identified within the frequency range from 0 to 2000 Hz for each spar. The experimental results for only one D-shape spar could be determined, however, and agreed within 13.8 percent of the analytical results. Frequencies corresponding to the five global modes for the three square spars agreed within 9.5, 11.6, and 8.5 percent of the respective analytical results and for the three elliptical spars agreed within 4.9, 7.7, and 9.6 percent of the respective analytical results.

Lake, Renee C.↗

NASA NTRS1992

The remarkable twisted disk of NGC 4753 and the shapes of galactic halos

The complex dust lanes in the S0 galaxy NGC 4753 are shown to be consistent with a disk that is strongly twisted by differential precession. Yet another peculiar S0 can therefore be explained as the result of an accretion event. An evolving disk model is fitted to the observed distribution. This disk is inclined by 15 deg relative to the galaxy's equatorial plane and twisted such that its line of nodes changes smoothly by 3.8 pi over a factor of seven in radius. The model indicates that most of the galaxy's mass is unseen, is nearly spherically distributed, and has a nearly scale-free spatial distribution. The ellipticity of the total galactic mass distribution must be constant to within 20 percent over the radial extent of the twisted disk - a conclusion which may significantly constrain galaxy formation mechanisms.

Steiman-Cameron, Thomas Y.↗

NASA NTRS1992

A determination of twisting of the Earth's magnetotail at distances 115-220 RE - ISEE 3

Observations from magnetic field and plasma experiments on ISEE 3 are used to identify and to analyze 16 crossings of the distant magnetotail neutral sheet. Four methods of analyses have been employed to measure the extent of the magnetotail twisting, which is found to be much greater than what was previously observed or, the theoretically inferred twist. A twist of more than 90 deg has frequently been observed on both open and closed magnetic field lines. In addition, the location of the magnetic neutral line of the magnetotail has been found to move over the distance interval of 115 to 220 Earth radii. Some features of these results suggest that a modification of the present solar wind-geomagnetic field interaction model may be needed.

Macwan, Snehavadan E.↗

NASA NTRS1993

Behavior of spinning laminated composite plates with initial twist-experimental vibrations, strain, and deflection results

The experimental behavior of spinning, pre-twisted laminated composite plates was investigated. The purpose of these experiments was to establish an experimental database consisting of strain, deflections, and natural frequencies as a function of rotational velocity. Six different plate sets were tested, that included three different stacking sequences (two symmetric, one asymmetric), two different initial twist levels (0 deg, 30 deg), and two different initial twist axis locations (midchord, quarter-chord). The plates were spin tested at four different combinations of pitch and sweep. It was observed that the location of the pretwist axis and the level of pretwist greatly affects the strain and deflections of the spinning plate, while only the pretwist level affects the measured natural frequencies.

Lapid, A. J.↗

NASA NTRS1938

Twisting failure of centrally loaded open-section columns in the elastic range

In the following report a complete theory of twisting failure by the energy method is developed, based on substantially the same assumptions as those employed by Wagner and Bleich. Problems treated in detail are: the stress and strain condition under St. Venant twist and in twist with axial constraint; the concept of shear center and the energy method for problems of elastic stability.

Kappus, Robert↗

NASA NTRS1994

Twisted Vanes Would Enhance Fuel/Air Mixing In Turbines

Computations of flow show performance of high-shear airblast fuel injector in gas-turbine engine enhanced by use of appropriately proportioned twisted (instead of flat) dome swirl vanes. Resultant more nearly uniform fuel/air mixture burns more efficiently, emitting smaller amounts of nitrogen oxides. Twisted-vane high-shear airblast injectors also incorporated into paint sprayers, providing advantages of low pressure drop characteristic of airblast injectors in general and finer atomization of advanced twisted-blade design.

Nguyen, H. Lee↗

NASA NTRS1993

Effects of cutouts on the behavior of symmetric composite laminates subjected to bending and twisting loads

Composite structures are used for a wide variety of aerospace applications. Practical structures contain cutouts and these structures are subjected to in-plane and out-of-plane loading conditions. Structurally efficient designs for composite structures require a thorough understanding of the effects of cutouts on the response of composite plates subjected to inplane or out-of-plane loadings. Most investigations of the behavior of composite plates with cutouts have considered in-plane loadings only. Out-of-plane loadings suchas bending or twisting have received very limited attention. The response of homogeneous plates (e.g., isotropic or orthotropic plates) subjected to bending or twisting moments has been studied analytically. These analyses are for infinite plates and neglect finite-plate effects. Recently, analytical and experimental studies were conducted to determine the effects of cutouts on the response of laminated composite plates subjected to bending moments. No analytical or experimental results are currently available for the effects of cutouts on the response of composite laminates subjected to twisting moments.

Prasad, C. B.↗

NASA NTRS1995

Report on twisted nematic and supertwisted nematic device characterization program

In this study we measured the optical characteristics of normally white twisted nematic (NWTN) and super twisted nematic (STN ) cells. Though no dynamic computer model was available, the static observations were compared with computer simulated behavior. The measurements were taken as a function of both viewing angle and applied voltage and included in the static case not only luminance but also contrast ratio and chromaticity . We employed the computer model Twist Cell Optics, developed at Kent State in conjunction with this study, and whose optical modeling foundation, Iike the ViDEOS program, is the 4 x 4 matrix method of Berreman. In order to resolve discrepancies between the experimental and modeled data the optical parameters of the individual cell components, where not known, were determined using refractometry, profilometry, and various forms of ellipsometry. The resulting agreement between experiment and model is quite good due primarily to a better understanding of the structure and optics of dichroic sheet polarizers. A description of the model and test cells employed are given in section 2. Section 3 contains the experimental data gathered and section 4 gives examples of the fit between model and experiment. Also included with this report are a pair of papers which resulted from the research and which detail the polarizer properties and some of the cell characterization methods.

Source record↗

NASA NTRS1996

Wing Twist Measurements at the National Transonic Facility

A technique for measuring wing twist currently in use at the National Transonic Facility is described. The technique is based upon a single camera photogrammetric determination of two dimensional coordinates with a fixed (and known) third dimensional coordinate. The wing twist is found from a conformal transformation between wind-on and wind-off 2-D coordinates in the plane of rotation. The advantages and limitations of the technique as well as the rationale for selection of this particular technique are discussed. Examples are presented to illustrate run-to-run and test-to-test repeatability of the technique in air mode. Examples of wing twist in cryogenic nitrogen mode are also presented.

Burner, Alpheus W.↗

NASA NTRS1998

Development of an Active Twist Rotor for Wind: Tunnel Testing (NLPN97-310

The development of the Active Twist Rotor prototype blade for hub vibration and noise reduction studies is presented in this report. Details of the modeling, design, and manufacturing are explored. The rotor blade is integrally twisted by direct strain actuation. This is accomplished by distributing embedded piezoelectric fiber composites along the span of the blade. The development of the analysis framework for this type of active blade is presented. The requirements for the prototype blade, along with the final design results are also presented. A detail discussion on the manufacturing aspects of the prototype blade is described. Experimental structural characteristics of the prototype blade compare well with design goals, and preliminary bench actuation tests show lower performance than originally predicted. Electrical difficulties with the actuators are also discussed. The presented prototype blade is leading to a complete fully articulated four-blade active twist rotor system for future wind tunnel tests.

Cesnik, Carlos E. S.↗

NASA NTRS2002

Visualization of Flows in Packed Beds of Twisted Tapes

A videotape presentation of the flow field in a packed bed of 48 twisted tapes which can be simulated by very thin virtual cylinders has been assembled. The indices of refraction of the oil and the Lucite twisted tapes were closely matched, and the flow was seeded with magnesium oxide particles. Planar laser light projected the flow field in two dimensions both along and transverse to the flow axis. The flow field was three dimensional and complex to describe, yet the most prominent finding was flow threads. It appeared that axial flow spiraled along either within the confines of a virtual cylindrical boundary or within the exterior region, between the tangency points, of the virtual cylinders. Random packing and bed voids created vortices and disrupted the laminar flow but minimized the entrance effects. The flow-pressure drops in the packed bed fell below the Ergun model for porous-media flows. Single-twisted-tape results of Smithberg and Landis (1964) were used to guide the analysis. In appendix A the results of several investigators are scaled to the Ergun model. Further investigations including different geometric configurations, computational fluid dynamic (CFD) gridding, and analysis are required.

Hendricks, R. C.↗

NASA NTRS2006

Magnetic Causes of Solar Coronal Mass Ejections: Dominance of the Free Magnetic Energy Over the Magnetic Twist Alone

We examine the magnetic causes of coronal mass ejections (CMEs) by examining, along with the correlations of active-region magnetic measures with each other, the correlations of these measures with active-region CME productivity observed in time windows of a few days, either centered on or extending forward from the day of the magnetic measurement. The measures are from 36 vector magnetograms of bipolar active regions observed within -30" of disk center by the Marshal Space Flight Center (MSFC) vector magnetograph. From each magnetogram, we extract six whole-active-region measures twice, once from the original plane-of-the-sky magnetogram and again a h r deprojection of the magnetogram to disk center. Three of the measures are alternative measures of the total nonpotentiality of the active region, two are alternative measures of the overall twist in the active-region's magnetic field, and one is a measure of the magnetic size of the active region (the active region's magnetic flux content). From the deprojected magnetograms, we find evidence that (1) magnetic twist and magnetic size are separate but comparably strong causes of active-region CME Productivity, and (2) the total free magnetic energy in an active region's magnetic field is a stronger determinant of the active region's CME productivity than is the field's overall twist (or helicity) alone. From comparison of results from the non-deprojected magnetograms with corresponding results from the deprojected magnetograms, we find evidence that (for prediction of active-region CME productivity and for further studies of active-region magnetic size as a cause of CMEs), for active regions within approx.30deg of disk center, active-region total nonpotentiality and flux content can be adequately measured from line-of-sight magnetograms, such as from SOH0 MDI.

Falconer, D. A.↗

NASA NTRS2006

Probing the Magnetic Causes of CMEs: Free Magnetic Energy More Important Than Either Size Or Twist

To probe the magnetic causes of CMEs, we have examined three types of magnetic measures: size, twist and total nonpotentiality (or total free magnetic energy) of an active region. Total nonpotentiality is roughly the product of size times twist. For predominately bipolar active regions, we have found that total nonpotentiality measures have the strongest correlation with future CME productivity (approx. 75% prediction success rate), while size and twist measures each have a weaker correlation with future CME productivity (approx. 65% prediction success rate) (Falconer, Moore, & Gary, ApJ, 644, 2006). For multipolar active regions, we find that the CME-prediction success rates for total nonpotentiality and size are about the same as for bipolar active regions. We also find that the size measure correlation with CME productivity is nearly all due to the contribution of size to total nonpotentiality. We have a total nonpotentiality measure that can be obtained from a line-of-sight magnetogram of the active region and that is as strongly correlated with CME productivity as are any of our total-nonpotentiality measures from deprojected vector magnetograms. We plan to further expand our sample by using MDI magnetograms of each active region in our sample to determine its total nonpotentiality and size on each day that the active region was within 30 deg. of disk center. The resulting increase in sample size will improve our statistics and allow us to investigate whether the nonpotentiality threshold for CME production is nearly the same or significantly different for multipolar regions than for bipolar regions. In addition, we will investigate the time rates of change of size and total nonpotentiality as additional causes of CME productivity.

Falconer, D. A.↗

NASA NTRS1996

Twist planet drive

A planetary gear system includes a sun gear coupled to an annular ring gear through a plurality of twist-planet gears, a speeder gear, and a ground structure having an internal ring gear. Each planet gear includes a solid gear having a first half portion in the form of a spur gear which includes vertical gear teeth and a second half portion in the form of a spur gear which includes helical gear teeth that are offset from the vertical gear teeth and which contact helical gear teeth on the speeder gear and helical gear teeth on the outer ring gear. One half of the twist planet gears are preloaded downward, while the other half are preloaded upwards, each one alternating with the other so that each one twists in a motion opposite to its neighbor when rotated until each planet gear seats against the sun gear, the outer ring gear, the speeder gear, and the inner ring gear. The resulting configuration is an improved stiff anti-backlash gear system.

Vranish, John M.↗

NASA NTRS2008

Split-Block Waveguide Polarization Twist for 220 to 325 GHz

A split-block waveguide circuit that rotates polarization by 90 has been designed with WR-3 input and output waveguides, which are rectangular waveguides used for a nominal frequency range of 220 to 325 GHz. Heretofore, twisted rectangular waveguides equipped with flanges at the input and output have been the standard means of rotating the polarizations of guided microwave signals. However, the fabrication and assembly of such components become difficult at high frequency due to decreasing wavelength, such that twisted rectangular waveguides become impractical at frequencies above a few hundred gigahertz. Conventional twisted rectangular waveguides are also not amenable to integration into highly miniaturized subassemblies of advanced millimeter- and submillimeter-wave detector arrays now undergoing development. In contrast, the present polarization- rotating waveguide can readily be incorporated into complex integrated waveguide circuits such as miniaturized detector arrays fabricated by either conventional end milling of metal blocks or by deep reactive ion etching of silicon blocks. Moreover, the present split-block design can be scaled up in frequency to at least 5 THz. The main step in fabricating a splitblock polarization-rotating waveguide of the present design is to cut channels having special asymmetrically shaped steps into mating upper and lower blocks (see Figure 1). The dimensions of the steps are chosen to be consistent with the WR-3 waveguide cross section, which is 0.864 by 0.432 mm. The channels are characterized by varying widths with constant depths of 0.432, 0.324, and 0.216 mm and by relatively large corner radii to facilitate fabrication. The steps effect both a geometric transition and the corresponding impedance-matched electromagnetic-polarization transition between (1) a WR-3 rectangular waveguide oriented with the electric field vector normal to the block mating surfaces and (2) a corresponding WR-3 waveguide oriented with its electric field vector parallel to the mating surfaces of the blocks. A prototype has been built and tested. Figure 2 presents test results indicative of good performance over nearly the entire WR-3 waveguide frequency band.

Ward, John↗