Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Superconducting microwave devices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Observation of interface piezoelectricity in superconducting devices on silicon

The development of superconducting quantum processors relies on understanding and mitigating decoherence in superconducting qubits. Piezoelectric coupling contributes to decoherence by mediating energy exchange between microwave photons and acoustic phonons. Although bulk centrosymmetric materials like silicon and sapphire are non-piezoelectric and commonly used as qubit substrates, the lack of centrosymmetry at interfaces may induce piezoelectric losses. This effect was predicted decades ago but never experimentally observed in superconducting devices. Here, we report interface piezoelectricity at aluminum-silicon junctions and demonstrate it as a significant loss channel in superconducting devices. Using aluminum interdigital transducers on silicon, we observe piezoelectric transduction from room to millikelvin temperatures, with an effective electromechanical coupling factor K 2 ≈ (3 ± 0.4) × 10−5%, comparable to weakly piezoelectric substrates. Modeling shows this mechanism limits qubit quality factors to Q ~ 10 4 − 10 8 , depending on surface participation and mode matching. These findings reveal interface piezoelectricity as a major dissipation channel and highlight the need for heterostructure and phononic engineering in next-generation superconducting qubits.

Zhou, Haoxin [University of California, Berkeley, ↗
DOE OSTI2024

Simulating the Phonon Collection Efficiency in KIPMDs

Kinetic inductance phonon-mediated (KIPM) detectors are superconducting microcalorimeters that use microwave kinetic inductance detectors (MKIDs) to read out phonon signals in the device substrate. In order to improve the design of these detectors, we need to understand the effect of various detector design elements on the physical processes that take place within the detector through simulation efforts. One figure of merit for KIPM detectors is the phonon collection efficiency, $\eta_{ph]$, defined as the ratio of phonon energy detected by the sensitive element in the detector and the energy deposited by incident phonons in the substrate. Comparing the phonon collection efficiency obtained in simulation and in experiment for the same detector geometry provides insight to physical processes in the detector, such as phonon absorption at substrate-sensor interfaces and phonon loss to non-sensitive detector elements. This work models the phonon collection efficiency in two KIPM detectors with different geometries, one located at the Fermi National Accelerator Laboraory, the other located at the SLAC National Accelerator Laboratory.

Dang, Stella Q.↗
NASA NTRS1993

Measuring Microwave Conductivities Of Superconducting Films

Microwave conductivities of thin films of high-temperature superconductors like YBa(3)Cu(3)O(7-delta) measured by noninvasive, nondestructive microwave-power-transmission method. Measurements yield useful information on superconducting and normal states of films and contribute to evaluation of films for use in microwave devices.

Bhasin, K. B.↗
NASA NTRS2021

Far-infrared Imager and Polarimeter for the Origins Space Telescope

The far-infrared imager and polarimeter (FIP) for the Origins Space Telescope (Origins) is a basic far-infrared imager and polarimeter. The camera will deliver continuum images and polarization measurements at 50 and 250μm. Currently available detector technologies provide sufficient sensitivity for background limited observations from space, at least on a single pixel basis. FIP incorporates large next-generation superconducting detector arrays and our technology development plan will push the pixel numbers for the arrays to the required size of 8000. Two superconducting detector technologies are currently candidates for the instrument: transition edge sensors or microwave kinetic inductance devices. Using these detectors and taking advantage of the cryogenic telescope that is provided by Origins, FIP will achieve mapping speeds of up to eight orders of magnitude faster than what has been achieved by existing observatories. The science drivers for FIP include observations of solar system objects, dust properties, and magnetic field studies of the nearby interstellar medium, and large scale galaxy surveys to better constrain the star formation history of the universe to address one of the main themes of Origins: “How does the Universe work?” In addition to the science, the FIP instrument plays a critical functional role in aligning the mirrors during on orbit observatory commissioning.

Astronomy↗
DOE OSTI2022

Methods for microwave characterization of electro-optic crystals for quantum transduction

Microwave-optic quantum transducers are essential devices to develop distributed quantum networks and implement related quantum communication protocols. Three dimensional high-coherence time microwave cavities embedded with electro-optic nonlinear dielectric materials provide promising platforms to boost the efficiency of the microwave-optic frequency conversion. However, so far, the properties for such dielectric crystals operating at milli-Kelvin cryogenic temperatures have not been well understood. Here, we propose a scheme to precisely measure and benchmark the dielectric constant and analyze the dissipation mechanisms of electro-optic materials, such as Lithium Niobate, at the quantum threshold. We will use Fermilab’s three dimensional superconducting cavities with long coherence time. The proposed method of microwave characterization lays the foundations for engineering quantum transduction devices and quantum sensors with high conversion efficiency and fidelity.

Zorzetti, Silvia↗
DOE OSTI2025

Additively-manufactured monocrystalline YBCO superconductor

Abstract Single-crystal microstructures enable high-performance YBa 2 Cu 3 O 7-x superconductors which are however limited to simple shapes due to their brittleness. Additive manufacturing can fabricate YBa 2 Cu 3 O 7-x superconductor with complex shapes, albeit with a polycrystalline microstructure. Here, we demonstrate a route to grow single-crystals from 3D-ink-printed, polycrystalline, sintered superconducting YBa 2 Cu 3 O 7-x (YBCO or Y123) + Y 2 BaCuO 5 (Y211), manufacturing objects with complex architectures displaying both high critical current density (J c =2.1 × 10 4 A . cm –2 , 77 K) and high critical temperature (T c = 88-89.5 K). An ink containing precursor powders (Y 2 O 3 , BaCO 3 , and CuO) is 3D-extruded into complex geometries and then reaction-sintered to obtain polycrystalline Y123 + Y211. A seed is then utilized to transform these 3D-printed parts from polycrystal to monocrystal via the melt growth method. The geometric details of 3D-printed parts survive the process without slumping, sagging or collapse, despite the long-term presence of liquid above the peritectic temperature. Origami structures can be created by sheet folding after 3D-printing. This additive approach enables the facile fabrication of superconducting devices with complex shapes and architectures, such as advanced undulator magnets to generate synchrotron radiation and microwave cavities for dark-matter axion search. This work highlights the potential of additive manufacturing for producing monocrystalline cuprate superconductors and opens the door to additive manufacturing of other monocrystalline functional ceramic or semiconductor materials.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Photon-Instanton Collider Implemented by a Superconducting Circuit

Instantons, spacetime-localized quantum field tunneling events, are ubiquitous in correlated condensed matter and high-energy systems. However, their direct observation through collisions with conventional particles has not been considered possible. We show how recent advances in circuit quantum electrodynamics, specifically, the realization of galvanic coupling of a transmon qubit to a high-impedance transmission line, allows the observation of inelastic collisions of single microwave photons with instantons (phase slips). We develop a formalism for calculating the photon-instanton cross section, which should be useful in other quantum field theoretical contexts. In particular, we show that the inelastic scattering probability can significantly exceed the effect of conventional Josephson quartic anharmonicity and reach order-unity values.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

High-Quality Factor Microwave Resonators using Rhenium

Coplanar waveguide resonators are a perfect tool to evaluate the losses induced by defects and interfaces in superconducting devices. Even if niobium is the most used superconductor for resonators and qubits, its native oxide at the metal-air (MA) interface limits the device results. Tantalum has recently significantly improved qubit performances due to a thinner and less disordered oxide layer compared to Nb. To further improve the MA interface, we used rhenium, a superconducting material with 1.7 K critical temperature resistant to oxidation: it forms an oxide layer thinner than 1 nm. In this study, we will present a thorough investigation of rhenium CPW resonator measurements with internal quality factors at the single photon level exceeding 2 million. The devices have been fabricated on a sapphire substrate while the processing parameters have been varying and optimized. The measurements have been performed as a function of power and temperature to disentangle different sources of losses, such as two-level systems (TLS) and quasi-particles. A peculiar TLS temperature dependence has been measured and analyzed. In this work, we also vary the participation ratio of the devices to extract the losses introduced by the involved interfaces with higher fidelity and precision. We carried on a deep material characterization effort to link the results to the differences in the fabrication steps, and we will present material characterization measurements performed via AFM, ToF-SIMS, XPS, and TEM.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1990

Microwave conductivity of laser ablated YBaCuO superconducting films and its relation to microstrip transmission line

The discovery of high temperature superconductor oxides has raised the possibility of a new class of millimeter and microwave devices operating at temperatures considerably higher than liquid helium temperatures. Therefore, materials properties such as conductivity, current density, and sheet resistance as a function of temperature and frequency, possible anisotropies, moisture absorption, thermal expansion, and others, have to be well characterized and understood. The millimeter wave response was studied of laser ablated YBa2Cu3O(7-x)/LaAlO3 thin films as a function of temperature and frequency. In particular, the evaluation of their microwave conductivity was emphasized, since knowledge of this parameter provides a basis for the derivation of other relevant properties of these superconducting oxides, and for using them in the fabrication of actual passive circuits. The microwave conductivity for these films was measured at frequencies from 26.5 to 40.0 GHz, in the temperature range from 20 to 300 K. The values of the conductivity are obtained from the millimeter wave power transmitted through the films, using a two fluid model.

Bhasin, K. B.↗
DOE OSTI2026

Tantalum alloy–based resonators for quantum information systems

Utilizing tantalum (Ta) in superconducting circuits has led to significant improvements, such as high qubit lifetime (T 1 ) and quality factors in both qubits and resonators, suggesting that material optimization plays an important role in the development of superconducting circuits. Thus we here explore superconducting gap engineering in Ta-based devices as a powerful strategy for expanding the range of suitable host materials. By alloying 20 atomic percent (at.%) hafnium into Ta thin films, we achieve a superconducting transition temperature (T c ) of 6.09 K as observed in direct current (DC) transport measurements, reflecting an increase in the superconducting gap. We systematically vary deposition conditions to control film orientation and transport properties of Ta-Hf alloy thin films. We then confirm the enhancement in T c via microwave measurements at millikelvin temperatures. We verify the ~40 increase in T c relative to bare Ta devices, while the loss contributions from two-level systems and quasi-particles remain unchanged in the low temperature regime. These findings emphasize the promise of material engineering in superconducting circuits and point to many potential material candidates for further exploration.

Ta-Hf alloy thin films↗
NASA NTRS1991

Microwave conductivity of laser ablated YBa2Cu3O(7-delta) superconducting films and its relation to microstrip transmission line performance

The discovery of high temperature superconductor oxides has raised the possibility of a new class of millimeter and microwave devices operating at temperatures considerably higher than liquid helium temperatures. Therefore, materials properties such as conductivity, current density, and sheet resistance as a function of temperature and frequency, possible anisotropies, moisture absorption, thermal expansion, and others, have to be well characterized and understood. The millimeter wave response of laser ablated YBa2Cu3O(7-delta)/LaAlO3 thin films was studied as a function of temperature and frequency. In particular, the evaluation of their microwave conductivity was emphasized, since knowledge of this parameter provides a basis for the derivation of other relevant properties of these superconducting oxides, and for using them in the fabrication of actual passive circuits. The microwave conductivity for these films was measured at frequencies from 26.5 to 40.0 GHz, in the temperature range from 20 to 300 K. The values of the conductivity are obtained from the millimeter wave power transmitted through the films, using a two fluid model.

Bhasin, K. B.↗
DOE OSTI2023

Simultaneous Brillouin and piezoelectric coupling to a high-frequency bulk acoustic resonator

Bulk acoustic resonators support robust, long-lived mechanical modes, capable of coupling to various quantum systems. In separate works, such devices have achieved strong coupling to both superconducting qubits, via piezoelectricity, and optical cavities, via Brillouin interactions. In this work, we present a hybrid microwave–optical platform capable of coupling to bulk acoustic waves through cavity-enhanced piezoelectric and photoelastic interactions. The modular, tunable system achieves fully resonant and well-mode-matched interactions among a 3D microwave cavity, a high-frequency bulk acoustic resonator, and a Fabry–Perot cavity. We realize this piezo–Brillouin interaction in x-cut quartz, demonstrating the potential for strong optomechanical interactions and high cooperativity using optical cavity enhancement. We further show how this device functions as a bidirectional electro–opto–mechanical transducer, with transduction efficiency exceeding 10 − <#comment/> 8 , and a feasible path towards unity conversion efficiency. The high optical sensitivity and ability to apply a large resonant microwave field in this system also offers a tool for probing anomalous electromechanical couplings, which we demonstrate by investigating (nominally centrosymmetric) C a F 2 and revealing a parasitic piezoelectricity of 83 am/V. Such studies are an important topic for emerging quantum technologies, and highlight the versatility of this hybrid platform.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Testing Low-Loss Microstrip Materials with MKIDs for Microwave Applications

Future measurements of the millimeter-wavelength sky require a low-loss superconducting microstrip, typically made from niobium and silicon-nitride, coupling the antenna to detectors. Here, we propose a simple device for characterizing these low-loss microstrips at 150 GHz. In our device we illuminate an antenna with a thermal source and compare the measured power at 150 GHz transmitted down microstrips of different lengths. The power measurement is made using Microwave Kinetic Inductance Detectors (MKIDs) fabricated directly onto the microstrip dielectric, and comparing the measured response provides a direct measurement of the microstrip loss. Our proposed structure provides a simple device (4 layers and a DRIE etch) for characterizing the dielectric loss of various microstrip materials and substrates. We present initial results using these devices. We demonstrate that the millimeter wavelength loss of microstrip lines, a few tens of millimeters long, can be measured using a practical aluminum MKID with a black body source at a few tens of Kelvin.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Low Noise Frequency-Domain Multiplexing of TES Bolometers Using SQUIDs at Sub-Kelvin Temperature

Digital Frequency-Domain Multiplexing (DfMux) is a technique that uses MHz superconducting resonators and Superconducting Quantum Interference Device (SQUID) arrays to read out sets of transition edge sensors. DfMux has been used by several Cosmic Microwave Background experiments, including most recently POLARBEAR-2 and SPT-3 G with multiplexing factors as high as 68, and is the baseline readout technology for the planned satellite mission LiteBIRD. Here, we present recent work focused on improving DfMux readout noise, reducing parasitic impedance, and improving sensor operation. We have achieved a substantial reduction in stray impedance by integrating the sensors, resonators, and SQUID array onto a single-carrier board operated at 250 mK. This also drastically simplifies the packaging of the cryogenic components and leads to better-controlled crosstalk. We demonstrate a low readout noise level of 8.6 pA/Hz1 1/2 , which was made possible by operating the SQUID array at a reduced temperature and with a low dynamic impedance. This is a factor of two improvement compared to the achieved readout noise level in currently operating Cosmic Microwave Background experiments using DfMux and represents a critical step toward maturation of the technology for the next generation of instruments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Magnetometry in a diamond anvil cell using nitrogen vacancy centers in a nanodiamond ensemble

The emerging field of optical magnetometry utilizing negative-charged nitrogen vacancy (NV – ) centers provides a highly sensitive lab bench technique for spatially resolved physical property measurements. Their implementation in high pressure diamond anvil cell (DAC) environments will become common as other techniques are often limited due to the spatial constraints of the sample chamber. Apparatus and techniques are described here permitting for more general use of magnetic field measurements inside a DAC using continuous wave optical detected magnetic resonance in NV – centers in a layer of nanodiamonds. A microstrip antenna delivers a uniform microwave field to the DAC and is compatible with simple metal gaskets, and the sensor layer of deposited nanodiamonds allows for simple determination of the magnetic field magnitude for B in the 1–100 G range. The ferromagnetic transition in iron at 18 GPa is measured with the apparatus, along with its hysteretic response.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Cryogenic growth of aluminum: Structural morphology, optical properties, superconductivity, and microwave dielectric loss

We explore the molecular beam epitaxy synthesis of superconducting aluminum thin films grown on c-plane sapphire substrates at cryogenic temperatures of 6 K and compare their behavior with films synthesized at room temperature. We demonstrate that cryogenic growth increases structural disorder, producing crystalline grains that modify the optical, electrical, and superconducting properties of aluminum. We observe that cryogenic deposition changes the color of aluminum from fully reflective to yellow and correlate the pseudodielectric function and reflectance with structural changes in the film. We find that smaller grain sizes enhance the superconductivity of aluminum, increasing its critical temperature and critical field. We then estimate the superconducting gap and coherence length of Cooper pairs in aluminum in the presence of disorder. In conclusion, we fabricate superconducting microwave resonators on these films and find that, independently of the growth temperature, the system is dominated by two-level system loss with similar quality factors in the high- and low-power regimes. We further measure a higher kinetic inductance in the cryogenically grown films.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Material exploration towards high quality factor microwave resonators

Niobium and aluminum have been widely used to realize superconducting resonators and qubits. However, the native oxide at the metal air interface limits the devices results. This layer is highly disordered, and it induces losses limiting the performances of the resonators or qubits. Recently, tantalum led to great improvement in qubit relaxation time. This improvement has been attributed to a thinner and less disordered oxide layer compared to Nb and Al. This study is aimed to limit the formation of the oxide layer, by the introduction of novel superconducting materials such as rhenium or by encapsulating the Nb surface with other superconducting materials such as Ta, Al, Re or other non-superconducting materials such as Au. To better understand the results, we are realizing these studies on coplanar waveguide resonators where the relation between surface losses and quality factor is clear. We are also analyzing different fabrication techniques to completely characterize our devices, linking material properties to the performances. In this work we are also varying the participation ratio of the devices in order to extract with higher fidelity and precision the losses introduced by the involved interfaces.

Crisa, F.↗