SEARCH · Engineering Papers

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1999

Aft Body Closure: Predicted Strut Effects at M=2.4

This paper reports the predicted M = 2.4 strut-interference effects on a closed aftbody with empennage for the TCA baseline model. The strut mounting technique was needed in order to assess the impact of aft-end shaping, i.e. open for a sting or closed to better represent a flight vehicle. However,this technique can potentially lead to unanticipated effects that are measured on the aft body. Therefore, a set of computations were performed in order to examine the closed aft body with and without strut present, at both zero and non-zero angles of sideslip (AOS). The work was divided into a computational task performed by Javier A. Garriz, using an inviscid (Euler) solver, and a monitoring/reporting task done by John E. Lamar. All this work was performed during FY98 at the NASA Langley Research Center.

Lamar, John E.↗

NASA NTRS2011

Evaluation of Long Composite Struts

Carbon-epoxy tapered struts are structurally efficient and offer opportunities for weight savings on aircraft and spacecraft structures. Seven composite struts were designed, fabricated and experimentally evaluated through uniaxial loading. The design requirements, analytical predictions and experimental results are presented. Struts with a tapered composite body and corrugated titanium end fittings successfully supported their design ultimate loads with no evidence of failure.

Jegley, Dawn C.↗

NASA NTRS2011

Highly Loaded Composite Strut Test Development

Highly loaded composite struts, representative of structural elements of a proposed truss-based lunar lander descent stage concept, were selected for design, development, fabrication and testing under NASA s Advanced Composites Technology program. The focus of this paper is the development of a capability for experimental evaluation of the structural performance of these struts. Strut lengths range from 60 to over 120 inches, and compressive launch and ascent loads can exceed -100,000 lbs, or approximately two times the corresponding tensile loads. Allowing all possible compressive structural responses, including elastic buckling, were primary considerations for designing the test hardware.

Wu, K. Chauncey↗

NASA NTRS2014

Development Testing and Subsequent Failure Investigation of a Spring Strut Mechanism

The NASA Engineering and Safety Center (NESC) and Lockheed Martin (LM) performed random vibration testing on a single spring strut development unit to assess its ability to withstand qualification level random vibration environments. Failure of the strut while exposed to random vibration resulted in a follow-on failure investigation, design changes, and additional development tests. This paper focuses on the results of the failure investigations referenced in detail in the NESC final report including identified lessons learned to aid in future design iterations of the spring strut and to help other mechanism developers avoid similar pitfalls.

Dervan, Jared↗

NASA NTRS2014

Development Testing and Subsequent Failure Investigation of a Spring Strut Mechanism

The NASA Engineering and Safety Center (NESC) and Lockheed Martin (LM) performed random vibration testing on a single spring strut development unit to assess its ability to withstand qualification level random vibration environments. Failure of the strut while exposed to random vibration resulted in a follow-on failure investigation, design changes, and additional development tests. This paper focuses on the results of the failure investigations referenced in detail in the NESC final report [1] including identified lessons learned to aid in future design iterations of the spring strut and to help other mechanism developers avoid similar pitfalls.

Dervan, Jared↗

NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. In particular, designs were considered for fabrication at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC). The designs presented in this paper do not represent the exact geometry and material systems currently in use by the Artemis landing system, but they are considered to be representative. The designs produced during this study will be used to develop manufacturing demonstration units (MDU) that can be fabricated at ISAAC and tested in lab facilities at LaRC

carbon-epoxy↗

NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

The goal of the current work was to develop an analytical framework for design of composite struts using various levels of model fidelity. Rapid optimization trade studies were performed using low fidelity two-dimensional (2D) axisymmetric models with smeared composite properties. The optimum 2D model was compared with three-dimensional (3D) models with higher levels of fidelity in material property representation. Good agreement was found with all models. The buckling performance of the highest fidelity 3D model was found to be satisfactory for the intended loading conditions. An additional goal of this work was to perform an initial assessment of using automated fiber placement (AFP) and other advanced manufacturing methods to explore their feasibility for the fabrication of struts for lunar landers, strut-braced wings, and other aerospace components. The designs produced during this study are intended to be used to develop manufacturing demonstration units (MDU) that can be fabricated at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at Langley Research Center (LaRC) and tested in lab facilities at LaRC.

carbon-epoxy↗

NASA NTRSDate not supplied

Design of a Manufacturing Demonstration Unit for a Composite Lunar Landing Gear Strut

carbon-epoxy↗

NASA NTRS2012

Strut Shaping of 34m Beam Waveguide Antenna for Reductions in Near-Field RF and Noise Temperature

Strut shaping of NASA's Deep Space Network (DSN) 34m Beam Waveguide (BWG) antenna has been implemented to reduce near-field RF exposure while improving the antenna noise temperature. Strut shaping was achieved by introducing an RF shield that does not compromise the structural integrity of the existing antenna. Reduction in the RF near-field level will compensate for the planned transmit power increase of the antenna from 20 kW to 80 kW while satisfying safety requirements for RF exposure. Measured antenna noise temperature was also improved by as much as 1.5 K for the low elevation angles and 0.5 K in other areas.

near-field↗

NASA NTRS2012

Strut Shaping of 34m Beam Waveguide Antenna for Reductions in Near-Field RF and Noise Temeperature

Struts shaping of the NASA's Deep Space Network (DSN) 34m Beam Waveguide (BWG) antenna has been implemented to reduce near-field RF exposure while improving the antenna noise temperature. Strut shaping was achieved by introducing an RF shield that does not compromise the structural integrity of the existing structure. Reduction in the RF near-field exposure will compensate for the planned transmit power increase of the antenna from 20 kW to 80 kW while satisfying safety requirements for RF exposure. Antenna noise temperature was also improved by as much as 1.5 K for the low elevation angles and 0.5 K in other areas. Both reductions of RF near-field exposure and antenna noise temperature were verified through measurements and agree very well with calculated results.

reflector↗

NASA NTRS1971

Development of the activated diffusion brazing process for fabrication of finned shell to strut turbine blades

The activated diffusion brazing process was developed for attaching TD-NiCr and U700 finned airfoil shells to matching Rene 80 struts obstructing the finned cooling passageways. Creep forming the finned shells to struts in combination with precise preplacement of brazing alloy resulted in consistently sound joints, free of cooling passageway clogging. Extensive tensile and stress rupture testing of several joint orientation at several temperatures provided a critical assessment of joint integrity of both material combinations. Trial blades of each material combination were fabricated followed by destructive metallographic examination which verified high joint integrity.

Wilbers, L. G.↗

NASA NTRS1975

A strut with infinitely adjustable thermal expansivity and length

A tubular strut with an integral mechanism for adjusting its thermal expansivity and length was developed to fulfill the stringent thermal stability requirements anticipated for the metering truss in the Large Space Telescope. Its features may be advantageously applied to a general variety of structures and precision mechanisms where dimensional control of component elements in a dynamic thermal environment is required. Detail, design, fabrication, and test of a developmental strut are discussed.

Nelson, P. T.↗

NASA NTRS1978

A method for calculating strut and splitter plate noise in exit ducts: Theory and verification

Portions of a four-year analytical and experimental investigation relative to noise radiation from engine internal components in turbulent flow are summarized. Spectra measured for such airfoils over a range of chord, thickness ratio, flow velocity, and turbulence level were compared with predictions made by an available rigorous thin-airfoil analytical method. This analysis included the effects of flow compressibility and source noncompactness. Generally good agreement was obtained. This noise calculation method for isolated airfoils in turbulent flow was combined with a method for calculating transmission of sound through a subsonic exit duct and with an empirical far-field directivity shape. These three elements were checked separately and were individually shown to give close agreement with data. This combination provides a method for predicting engine internally generated aft-radiated noise from radial struts and stators, and annular splitter rings. Calculated sound power spectra, directivity, and acoustic pressure spectra were compared with the best available data. These data were for noise caused by a fan exit duct annular splitter ring, larger-chord stator blades, and turbine exit struts.

Fink, M. R.↗

NASA NTRS1979

Noise from struts and splitters in turbofan exit ducts

An analytical method for calculating noise radiation from isolated airfoils in turbulent flow was combined with a method for calculating transmission of sound through a subsonic exit duct and with an empirical far field directivity shape. This combination provides a method for predicting engine internally generated noise from radial struts and stators and annular splitter rings. Calculated sound power spectra, directivity, and acoustic pressure spectra are compared with data. These data were for noise caused by a fan exit duct splitter ring, large-chord stator blades, and turbine exit struts. However, the lack of turbulence intensity and scale length measurements for these flow ducts prevented an absolute validation of the prediction method.

Fink, M. R.↗

NASA NTRS1980

Flameholding characteristics of a swept-strut H2 fuel-injector for scramjet applications

A series of direct-connect tests are conducted which simulate the flow around the center swept-strut fuel-injector of a scramjet engine module. The experimental geometry includes both perpendicular and parallel fuel injectors which are swept with respect to the upstream flow direction in a manner simulating the flow geometry in the combustion region of the scramjet module. Seven different strut injector geometries are evaluated for their performance, flameholding, and inlet-combustor interaction characteristics. The most efficient combustion process is exhibited by the configuration having the deepest step with perpendicular injector orifices located 3.5 to 4.5 step heights downstream from the step. However, long centerbody and staged injection configurations perform as equally well as the deep step configuration when evaluating only the amount of perpendicular fuel injection. Since the staged injection configuration exhibits the lowest ignition and flameholding limit, it is suggested that the optimum injection configuration should incorporate a deep step with staged injection in order to improve the low temperature autoignition-flameholding characteristics.

Northam, G. B.↗

NASA NTRS1983

Passive Orbital Disconnect Strut (PODS 3), structural and thermal test program

A test program is undertaken to verify that the lifetime of a shuttle launchable dewar can be increased by using passive orbital disconnect struts (PODS). A detailed design is performed on the cold end (PODS-III) portion of the strut. Structural analysis of the thin-wall fiberglass tube allows selection of the optimum winding angle and tube dimensions. Structural tests on the thin-wall fiberglass tube measure both the tension and compression modulus at ambient and LN2 temperatures, the radial deflection versus side load, and the ultimate compression strength of the tube at LN2 temperature. The thermal expansion of the fiberglass tube plus Invar is also measured down to 78 K. The axial gap at the wedge portion of the stem is set based on these data. The PODS-III test article parts are fabricated and assembled using a detailed assembly procedure. The thermal conductants in the orbital configuration was measured for body temperatures between 5 and 40 K. This temperature range covers the predicted ground hold and orbit temperatures for vapor-cooled supports. The test results are then compared with heat leak values predicted before the test began. Side load, axial compression load, and tension load tests conclude the test program.

Parmley, R. T.↗

NASA NTRS1986

Toggle Hinge for Deployable Struts

Toggle hinge allows deployable structures erected without end play encountered in conventional hinged structural members. New hinge ensures rigidity in portable bridges, masts, towers, platforms, and other deployable (and retractable) structures. Positioned halfway along length of folding strut, hinge allows halves of strut to pivot 180 degrees about center.

Barbour, R. T.↗

NASA NTRS1984

Passive orbital disconnect strut

The design and test results with a third generation passive orbital disconnect strut (PODS) for space-based cryogenic He dewars are presented. Three pairs of PODS struts support a tank and change lengths in response to gas and temperature changes. A thin wall fiberglass tube is used on the cold disconnect end, which can be operated on the ground or in space. Tests were performed to characterize heat flows across the cold end to a liquid He sink and subsequent vacuum pressure within the He tank. Heat transfer was lower than predicted, suggesting that longer dewar in-orbit lifetimes can be expected with the new PODS.

Parmley, R. T.↗