Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Structural Impact Dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗
NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗
DOE OSTI2024

Salt matters: How ionic strength and electrolytes impact redox polymer reactivity and dynamics for energy storage

As the global demand for sustainable energy grows, redox-active polymers (RAPs) have emerged as promising materials for batteries due to their advantages in stability, ease of preparation, and low-cost processability. Despite factors traditionally known to impact polymer dynamics (e.g., temperature, viscosity, and structure), we posit that investigating the effect of ionic strength and/or supporting electrolyte types on the electrochemical performance of RAP systems is crucial, both in aqueous and nonaqueous systems. Here, we first highlight recent findings on RAP-electrolyte interactions, elucidating how their polyelectrolyte nature determines their redox activity. Then, we focus on strategies to enhance RAP performance for energy storage through ionic strength optimization and tailored electrolyte composition. These insights into the modulation of RAP reactivity provide a foundation for improving battery performance in both flow and stationary configurations, thus facilitating progress toward next-generation energy storage solutions.

25 ENERGY STORAGE↗
NASA NTRS1988

Current research in composite structures at NASA's Langley Research Center

Research on the mechanics of composite structures at NASA's Langley Research Center is discussed. The advantages and limitations of special purpose and general purpose analysis tools used in research are reviewed. Future directions in computational structural mechanics are described to address analysis short-comings. Research results on the buckling and postbuckling of unstiffened and stiffened composite structures are presented. Recent investigations of the mechanics of failure in compression and shear are reviewed. Preliminary studies of the dynamic response of composite structures due to impacts encountered during crash-landings are presented. Needs for future research are discussed.

Card, Michael F.↗
NASA NTRS1992

Optical distributed sensors for feedback control: Characterization of photorefractive resonator

The aim of the project was to explore, define, and assess the possibilities of optical distributed sensing for feedback control. This type of sensor, which may have some impacts in the dynamic control of deformable structures and the monitoring of small displacements, can be divided into data acquisition, data processing, and control design. Analogue optical techniques, because they are noninvasive and afford massive parallelism may play a significant role in the acquisition and the preprocessing of the data for such a sensor. Assessing these possibilities was the aim of the first stage of this project. The scope of the proposed research was limited to: (1) the characterization of photorefractive resonators and the assessment of their possible use as a distributed optical processing element; and (2) the design of a control system utilizing signals from distributed sensors. The results include a numerical and experimental study of the resonator below threshold, an experimental study of the effect of the resonator's transverse confinement on its dynamics above threshold, a numerical study of the resonator above threshold using a modal expansion approach, and the experimental test of this model. A detailed account of each investigation, including methodology and analysis of the results are also included along with reprints of published and submitted papers.

Indebetouw, Guy↗
NASA NTRS2014

Investigating the Aerosol Optical and Radiative Characteristics of Heavy Haze Episodes in Beijing During January of 2013

Several heavy atmospheric haze pollution episodes occurred over eastern and northern China during January of 2013. The pollution covered more than 100 sq km and caused serious impacts on environmental quality, human health, and transportation. In this study, we characterize aerosol microphysical, optical, and radiative characteristics using a combination of ground-based Sun/sky radiometer retrievals and a radiative transfer model. Our results show that during about half of the total number of days, daily PM2.5 and PM10 concentrations are larger than 100 microg/cu m, with maxima of 462 and 433 microg/cu m, respectively, during the haze events. Fine-mode (PM2.5) particles dominated the aerosol size during the episodes. The volume size distribution and median radius of fine-mode particles generally increase as aerosol optical depth at 440 nm (AOD440) increases. The median effective radius of fine-mode particles increases from 0.15 microns at low AOD value (AOD440~0.3) to a radius of 0.25-0.30 microns at high AOD value (AOD440> or = 1.0). The daily mean single-scattering albedo (SSA), imaginary part of refractive index (RI), and asymmetry factor display pronounced spectral behaviors. The overall mean SSA440 and SSA675 are 0.892 and 0.905, respectively. The corresponding RI440 and RI675 are 0.016 and 0.011, respectively. This indicates that a significant amount of absorption occurred under the haze event in Beijing during January 2013. Approximately half of the incident solar radiation energy went into heating the atmosphere as a result of strong aerosol loading and absorption. The daily averaged heating rate in the haze particle layer (0-3.2 km) varies from 0.12 to 0.81 K/day in Beijing, which might exert profound impact on the atmospheric thermodynamic and dynamical structures and cloud development, which should be further studied.

bejing↗
NASA NTRS2020

Investigation of Atmospheric Boundary-Layer Effects on Launch-Vehicle Ground Wind Loads

A launch vehicle ground-wind-loads program is underway at the NASA Langley Transonic Dynamics Tunnel. The objectives are to quantify key aerodynamic and structural characteristics that impact the occurrence of large wind-induced oscillations of a launch vehicle when exposed to ground winds prior to launch. Of particular interest is the dynamic response of a launch vehicle when a von Kármán vortex street forms in the wake of the vehicle resulting in quasiperiodic lift and drag forces. Vehicle response to these quasiperiodic forces can become quite large when the frequency of vortex shedding nears that of a lowly-damped structural mode thereby exciting a resonant response. Wind approaching the vehicle can be characterized by a varying speed with height and turbulence content. The combination of both the varying speed and turbulence content is referred to herein as the atmospheric boundary-layer. The importance of the atmospheric boundary-layer upon launch vehicle wind-induced oscillation response has long been questioned, and its effects are not well understood. Although there are several facilities around the world dedicated to replicating atmospheric boundary layers, the development of such a boundary layer in a wind tunnel capable of producing flight-representative Reynolds numbers for aeroelastically-scaled launch vehicle models has only recently been accomplished. The NASA Langley Transonic Dynamics Tunnel is capable of simulating flight-representative Reynolds numbers of launch vehicles on the pad and is uniquely capable of replicating many fluid-structure scaling parameters typical of aeroelastic tests. Recent test efforts successfully developed representative atmospheric boundary-layers for three launch sites in the Transonic Dynamics Tunnel, thereby allowing all known aerodynamic and fluid-structure coupling parameters to be simultaneously simulated for those sites. Dynamic aeroelastically-scaled models representative of typical large launch vehicles were constructed for testing. Aeroelastic scaling includes matching geometry, mode shapes, reduced frequencies, damping, running mass ratios, and running stiffness ratios. The models were tested in smooth uniform flow and then immersed in the atmospheric boundary-layer for comparison of these effects. Dynamic data were acquired measuring unsteady pressure, acceleration, and base bending moment. It was discovered that peak dynamic loads resulting from resonant wind-induced oscillation response are similar when acquired in either smooth uniform flow or an atmospheric boundary-layer. This indicates that resonant lock-in events are minimally impacted by representative turbulence and/or wind profile. Alternately, nonresonant wind-induced oscillation response events are stronger when acquired in an atmospheric boundary-layer. This indicates that a lowly-damped structural response will increase when exposed to an increased magnitude of random excitation, which is consistent with historical comparisons. Loads created by the resonant response events were substantially stronger than those from the nonresonant response events. Therefore, if testing is done to simply identify worst-case conditions and load magnitude, then smooth uniform flow is likely an adequate test technique. However, if nonresonant response loads are of primary interest, then atmospheric boundary-layer simulation is required.

Thomas G Ivanco↗
NASA NTRS1982

Structures and Dynamics Division research and technology plans, FY 1982

Computational devices to improve efficiency for structural calculations are assessed. The potential of large arrays of microprocessors operating in parallel for finite element analysis is defined, and the impact of specialized computer hardware on static, dynamic, thermal analysis in the optimization of structural analysis and design calculations is determined. General aviation aircraft crashworthiness and occupant survivability is also considered. Mechanics technology required for design coefficient, fault tolerant advanced composite aircraft components subject to combined loads, impact, postbuckling effects and local discontinuities are developed.

Bales, K. S.↗
NASA NTRS1993

Explicit solution techniques for impact with contact constraints

Modern military aircraft transparency systems, windshields and canopies, are complex systems which must meet a large and rapidly growing number of requirements. Many of these transparency system requirements are conflicting, presenting difficult balances which must be achieved. One example of a challenging requirements balance or trade is shaping for stealth versus aircrew vision. The large number of requirements involved may be grouped in a variety of areas including man-machine interface; structural integration with the airframe; combat hazards; environmental exposures; and supportability. Some individual requirements by themselves pose very difficult, severely nonlinear analysis problems. One such complex problem is that associated with the dynamic structural response resulting from high energy bird impact. An improved analytical capability for soft-body impact simulation was developed.

Mccarty, Robert E.↗
NASA NTRS1991

Space Station Freedom solar dynamic modules structural modelling and analysis

In support of the Space Station Freedom (SSF) Solar Dynamic Power Module effort, structural design studies were performed to investigate issues related to the design of the power module, its pointing capabilities, and the integration of the module into the SSF infrastructure. Of particular concern from a structural viewpoint are the dynamics of the power module, the impact of the power module on the Space Station dynamics and controls, and the required control effort for obtaining the specified Solar Dynamic Power Module pointing accuracy. Structural analyses were performed to determine the structural dynamics attributes of both the existing and the proposed structural dynamics module designs. The objectives of these analyses were to generate validated Solar Dynamic Power Module NASTRAN finite element models, combine Space Station and power module models into integrated system models, perform finite element modal analyses to assess the effect of the relocations of the power module center of mass, and provide modal data to controls designers for control systems design.

Lawrence, Charles↗
DOE OSTI2025

Influence of solutes on the core structures of $\langle$ α $\rangle$-type screw dislocations in $α$-Ti

The $\langle$ α $\rangle$-type screw dislocations are known to be significant mediators of plasticity in hexagonal-close-packed (HCP) metals. These dislocations have polymorphic core structures, and subtle changes in the relative energies of these core structures are known to have a large impact on the dynamics of the dislocations. Here, this work identifies a previously neglected long-range elastic interstitial-solute/dislocation interaction that influences the core structures. Essentially, interstitial solutes induce a change in the dislocation core structure to minimize the energy of interaction between the solutes and the dislocation. Molecular dynamics simulations, continuum linear elasticity, and statistical analysis show that this long-range interaction can locally alter the dislocation cores so that many different polymorphs appear along a single dislocation not only because of direct contact between interstitials and the dislocation core but also because of this long-range elastic interaction.

36 MATERIALS SCIENCE↗
NASA NTRS2022

Impact Simulation of Composite Panels for Aerospace Applications

The aerospace research community has been working towards the development of a comprehensive framework for the design of composite structures at the component, subassembly, assembly, and system levels. Such a framework requires accurate, efficient and easy-to-use mathematical and computational models that are in sync with physical reality. The research work in this paper is designed to help an aerospace structural engineer move towards this goal by simulating dynamic impact to composite panels. First, the existing orthotropic visco-elastic visco-plastic material model in LS-DYNA commercial finite element program, MAT_COMPOSITE_TABULATED_PLASTICITY_DAMAGE (MAT_213) is enhanced with the development and use of rate-dependent damage data. Using state-of-the-art experimental procedures, impact validation test data are created. Second, the versatility of the constitutive model is examined by its ability to simulate a low velocity (27 ft/s, 8 m/s) impact test, and two high velocity impact tests (385–417 ft/s, 117–127 m/s) that straddle the ballistic limit of the projectile and the composite panels. Third, these impact events are modeled using three different finite element types – under-integrated and fully-integrated solid elements, and fully-integrated thin shell elements. Insight into accuracy versus numerical efficiency is gained by comparing the performance of solid versus thin shell elements. The numerical results show that accurate predictions of these impact events can be obtained with reasonable effort and care.

Simulations↗
NASA NTRS1995

Aeroelasticity of wing and wing-body configurations on parallel computers

The objective of this research is to develop computationally efficient methods for solving aeroelasticity problems on parallel computers. Both uncoupled and coupled methods are studied in this research. For the uncoupled approach, the conventional U-g method is used to determine the flutter boundary. The generalized aerodynamic forces required are obtained by the pulse transfer-function analysis method. For the coupled approach, the fluid-structure interaction is obtained by directly coupling finite difference Euler/Navier-Stokes equations for fluids and finite element dynamics equations for structures. This capability will significantly impact many aerospace projects of national importance such as Advanced Subsonic Civil Transport (ASCT), where the structural stability margin becomes very critical at the transonic region. This research effort will have direct impact on the High Performance Computing and Communication (HPCC) Program of NASA in the area of parallel computing.

Byun, Chansup↗
NASA NTRS2018

NASA ACC High Energy Dynamic Impact Methodology and Outcomes

For High Energy Dynamic Impact (HEDI) events, testing to evaluate the structural response of primary aircraft structure for design and certification is both expensive and time consuming. This paper discusses current work seeking to assess, develop, and validate appropriate analytical models that accurately predict physical response, damage, and failure modes for large scale composite structures in HEDI events. Four state-of-the-art Progressive Damage Analysis (PDA) methods were employed for this phased project: LS-DYNA MAT162, LS-DYNA MAT261, Smoothed Particle Galerkin (SPG), and EMU Peridynamics. Multiple material systems were considered, namely T700/5208 textile-infusion triaxial braid, T800/AMD-825 textile-infusion triaxial braid, IM7/8552 uni-directional tape, and SPG 196-PW/8552 plain-weave fabric. Extensive ballistic impact testing was performed to support this activity and measured results were compared to predictive models for assessment using panel delamination, panel displacement, force at the load cells, and threshold velocity as measures. Ultimately, the work under this activity provided significant progress in advancing the state-of-the-art in the use of PDA for HEDI events. Each material model had favorable performance comparing to test in some parameters and needed improvement in others. With the lessons learned from this activity, significant progress was made in the ability to predict panel behavior for a more general case beyond the flat panel in a ballistic impact event. Subsequent Phase II of the NASA ACC HEDI effort will continue to build on the coupon testing, flat panel ballistic impact testing, and analysis performed to-date with application of the PDA methods for intended material selections to test articles with greater complexity of configuration, curvature, and scale. It is not the intention of this paper to present a full set of data, but rather to give an overview of the NASA HEDI effort and show a small representative subset of the test and analysis results.

Hunziker, Kenneth J.↗
NASA NTRS1977

Dynamical implications of the petrology and distribution of impact melt rocks

Petrographic and structural relations of rocks resulting from melting of target materials during impact indicate constraints that can be applied to theoretical models and experimental production of craters. Topics discussed in this context include the motion of shock melted material, the mixing of melts, the energies required for heating and melting the necessary volumes of target rocks, diameter to depth ratios, and the formation of structural modifications. The motion of shock melted material involves ejection of some of the lowermost parts of the target, incorporation of distant fragmental material, outward flow, settling into cracks after breccia formation, and completion in a short time span. Melts must be completed within tens of seconds to a couple of minutes after impact.

Phinney, W. C.↗
DOE OSTI2024

Studying Wind Loading on CSP Collectors to Improve Performance and Reliability

Electricity generation through Concentrating Solar-thermal Power (CSP) adds the advantage of thermal energy storage and heat production. CSP collector costs constitute nearly one-third of total plant costs. Managing wind loading, especially dynamic wind loading caused by the turbulent wind flow, is a significant design challenge. Traditional collector designs rely on wind tunnel experiments and numerical simulations, which do not fully capture dynamic effects. Here, we provide an overview of NREL's activities on wind loading on CSP collectors, aiming to improve their reliability and cost-efficiency. We present insights from field measurements at operational parabolic trough and power-tower CSP plants. Over two years, we measured turbulent wind fields and resulting structural loads in a parabolic trough plant, revealing wind, turbulence, and collector field interactions. Similar measurements are ongoing at the Crescent Dunes heliostat field. These campaigns show how atmospheric turbulence, wind direction, and collector orientation affect dynamic wind loading. Upwind collector structures can generate turbulent structures, causing fluctuating loads at downstream collectors, impacting fatigue lifetime and optical efficiency. Preliminary results indicate that interior collectors experience higher turning moments than those at the edges, suggesting higher drive wear. At Crescent Dunes, we use instrumented heliostats at the field's edge and interior to study the translation of turbulent wind to dynamic structural loads. The campaign is still ongoing, and we will present first findings. Another focus of our work is tying the experimental wind loading findings to optical performance of the collectors, using simulation tools. For example, we derive torsional errors of the parabolic troughs - the angular offset from the sun position along a collector row. This error is impacted by wind-induced mirror deformations. Future work will focus on continuing the measurement efforts and combining them with computational fluid dynamic simulations. By providing detailed field measurements and validated models, our efforts aim to enhance understanding of wind loading on CSP collectors, improving their structural integrity and optical performance.

CSP↗
NASA NTRS1984

Crashworthiness of light aircraft fuselage structures: A numerical and experimental investigation

The dynamic behavior of aircraft fuselage structures subject to various impact conditions was investigated. An analytical model was developed based on a self-consistent finite element (CFE) formulation utilizing shell, curved beam, and stringer type elements. Equations of motion were formulated and linearized (i.e., for small displacements), although material nonlinearity was retained to treat local plastic deformation. The equations were solved using the implicit Newmark-Beta method with a frontal solver routine. Stiffened aluminum fuselage models were also tested in free flight using the UTIAS pendulum crash test facility. Data were obtained on dynamic strains, g-loads, and transient deformations (using high speed photography in the latter case) during the impact process. Correlations between tests and predicted results are presented, together with computer graphics, based on the CFE model. These results include level and oblique angle impacts as well as the free-flight crash test. Comparisons with a hybrid, lumped mass finite element computer model demonstrate that the CFE formulation provides the test overall agreement with impact test data for comparable computing costs.

Nanyaro, A. P.↗