Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Si3N4”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Development of Si3N4 for gas turbine applications

Activities associated with materials research are often concerned with composition and intrinsic properties as opposed to formability. To overcome this problem, Taguchi-designed experiments were utilized to develop process parameters for a formable Si3N4 powder. Using these experiments, the transfer of a research-based material (prepared by isostatic pressing) to a component formable material (prepared by casting) was accomplished while preserving properties required for gas-turbine applications.

Taglialavore, Antoni P.↗
NASA NTRS1990

Characterization of interfacial failure in SiC reinforced Si3N4 matrix composite material by both fiber push-out testing and Auger electron spectroscopy

AES depth profiling and a fiber push-out test for interfacial shear-strength determination have been used to ascertain the mechanical/chemical properties of the fiber/matrix interface in SiC-reinforced reaction-bonded Si3N4, with attention to the weak point where interfacial failure occurs. In the cases of both composite fracture and fiber push-outs, the interfacial failure occurred either between the two C-rich coatings that are present on the double-coated SiC fibers, or between the inner C-rich coating and the SiC fiber. Interface failure occurs at points of very abrupt concentration changes.

Eldridge, J. I.↗
NASA NTRS1989

Impact behavior of a SiC fiber-reinforced reaction bonded Si3N4 composite

Impact tests were performed on a series of ceramic plate specimens. Monolithic (unreinforced) and composite specimens with various fiber layups were tested to determine the effect that the fiber reinforcement has on impact damage initiation and dynamic response of the ceramic materials. Results show that a porous surface layer of Si3N4 on the composite specimens can enhance the energy absorbing capability of the composite specimens. The addition of SiC fiber reinforcement to the RBSN matrix material is also shown to significantly change the mode of failure and reduce the extent of damage due to impact.

Grady, J.↗
NASA NTRS1991

Influence of the Si3N4 microstructure on its R-curve and fatigue behavior

The R-curve and fatigue behavior of a silicon nitride with large, highly elongated grains were compared to those of a silicon nitride with smaller, more equiaxed grains. The former was found to have higher toughness and a slightly rising R-curve which enhanced fatigue resistance, while the latter had constant toughness with crack length. The R-curve was attributed to crack deflection and grain pull-out. The microstructure did not influence the dynamic fatigue properties of the two ceramics, as both had good resistance to dynamic fatigue. The cyclic fatigue resistance of the large-grained Si3N4, however, was surprisingly low.

Tikare, Veena↗
NASA NTRS1991

Evidence from transmission electron microscopy for an oxynitride layer in oxidized Si3N4

Microstructural and energy dispersive spectrometry evidence is produced, from transmission electron microscopy, to show that a silicon oxynitride inner layer is produced by the oxidation of silicon nitride in dry oxygen at 1350 C as proposed by Tressler et al. (1989). However, details of the microstructures at the oxide/nitride interface do not agree entirely with the rest of the Tressler model for the oxidation of Si3N4.

Ogbuji, Linus U. J. T.↗
NASA NTRS1992

Oxidation effects on the mechanical properties of a SiC-fiber-reinforced reaction-bonded Si3N4 matrix composite

The room-temperature mechanical properties of SiC fiber reinforced reaction bonded silicon nitride composites were measured after 100 hrs exposure at temperatures to 1400 C in nitrogen and oxygen environments. The composites consisted of approx. 30 vol percent uniaxially aligned 142 micron diameter SiC fibers in a reaction bonded Si3N4 matrix. The results indicate that composites heat treated in a nitrogen environment at temperatures to 1400 C showed deformation and fracture behavior equivalent to that of the as-fabricated composites. Also, the composites heat treated in an oxidizing environment beyond 400 C yielded significantly lower tensile strength values. Specifically in the temperature range from 600 to 1000 C, composites retained approx. 40 percent of their as-fabricated strength, and those heat treated in the temperatures from 1200 to 1400 C retained 70 percent. Nonetheless, for all oxygen heat treatment conditions, composite specimens displayed strain capability beyond the matrix fracture stress; a typical behavior of a tough composite.

Bhatt, Ramakrishna T.↗
NASA NTRS1992

Reaction-bonded Si3N4 and SiC matrix composites

A development status evaluation is presented for the reaction-bonded SiC- and Si3N4-matrix types of fiber-reinforced ceramic-matrix composite (FRCMC). A variety of reaction-bonding methods are being pursued for FRCMC fabrication: CVI, CVD, directed metal oxidation, and self-propagating high-temperature synthesis. Due to their high specific modulus and strength, toughness, and fabricability, reaction-bonded FRCMC are important candidate materials for such heat-engine components as combustor liners, nozzles, and turbine and stator blading. The improvement of long-term oxidative stability in these composites is a major goal of current research.

Bhatt, Ramakrishna T.↗
NASA NTRS1994

Effects of Thermal Cycling on Thermal Expansion and Mechanical Properties of Sic Fiber-reinforced Reaction-bonded Si3n4 Composites

Thermal expansion curves for SiC fiber-reinforced reaction-bonded Si3N4 matrix composites (SiC/RBSN) and unreinforced RBSN were measured from 25 to 1400 C in nitrogen and in oxygen. The effects of fiber/matrix bonding and cycling on the thermal expansion curves and room-temperature tensile properties of unidirectional composites were determined. The measured thermal expansion curves were compared with those predicted from composite theory. Predicted thermal expansion curves parallel to the fiber direction for both bonding cases were similar to that of the weakly bonded composites, but those normal to the fiber direction for both bonding cases resulted in no net dimensional changes at room temperature, and no loss in tensile properties from the as-fabricated condition. In contrast, thermal cycling in oxygen for both composites caused volume expansion primarily due to internal oxidation of RBSN. Cyclic oxidation affected the mechanical properties of the weakly bonded SiC/RBSN composites the most, resulting in loss of strain capability beyond matrix fracture and catastrophic, brittle fracture. Increased bonding between the SiC fiber and RBSN matrix due to oxidation of the carbon-rich fiber surface coating and an altered residual stress pattern in the composite due to internal oxidation of the matrix are the main reasons for the poor mechanical performance of these composites.

Bhatt, R. T.↗
NASA NTRS1999

SiC and Si3N4 Recession Due to SiO2 Scale Volatility Under Combustor Conditions

SiC and Si3N4 materials were tested under various turbine engine combustion environments, chosen to represent either conventional fuel-lean or fuel-rich mixtures proposed for high speed aircraft. Representative CVD, sintered, and composite materials were evaluated in both furnace and high pressure burner rig exposure. While protective SiO2 scales form in all cases, evidence is presented to support paralinear growth kinetics, i.e. parabolic growth moderated simultaneously by linear volatilization. The volatility rate is dependent on temperature, moisture content, system pressure, and gas velocity. The burner tests were used to map SiO2 volatility (and SiC recession) over a range of temperature, pressure, and velocity. The functional dependency of material recession (volatility) that emerged followed the form: exp(-QIRT) * P(exp x) * v(exp y). These empirical relations were compared to rates predicted from the thermodynamics of volatile SiO and SiO(sub x)H(sub Y) reaction products and a kinetic model of diffusion through a moving, boundary layer. For typical combustion conditions, recession of 0.2 to 2 micron/h is predicted at 1200- 1400C, far in excess of acceptable long term limits.

Smialek, James L.↗
NASA NTRS1999

SiC and Si3N4 Recession Due to SiO2 Scale Volatility Under Combustor Conditions

Silicon carbide (SiC) and Si3N4 materials were tested in various turbine engine combustion environments chosen to represent either conventional fuel-lean or fuel-rich mixtures proposed for high-speed aircraft. Representative chemical vapor-deposited (CVD), sintered, and composite materials were evaluated by furnace and high-pressure burner rig exposures. Although protective SiO2 scales formed in all cases, the evidence presented supports a model based on paralinear growth kinetics (i.e., parabolic growth moderated simultaneously by linear volatilization). The volatility rate is dependent on temperature, moisture content, system pressure, and gas velocity. The burner tests were thus used to map SiO2 volatility (and SiC recession) over a range of temperatures, pressures, and velocities. The functional dependency of material recession (volatility) that emerged followed the form A[exp(-Q / RT)](P(sup x)v(sup y). These empirical relations were compared with rates predicted from the thermodynamics of volatile SiO and SiOxHy reaction products and a kinetic model of diffusion through a moving boundary layer. For typical combustion conditions, recession of 0.2 to 2 micrometers/hr is predicted at 1200 to 1400 C, far in excess of acceptable long-term limits.

Smialek, James L.↗
NASA NTRS2002

Additive Effects on Si3n4 Oxidation/Volatilization in Water Vapor

Two commercially available additive-containing silicon nitride materials were exposed in four environments which range in severity from dry oxygen at 1 atm pressure, and low gas velocity to an actual turbine engine. Oxidation and volatilization kinetics were monitored at temperatures ranging from 1066 to 1400 C. The main purpose of this paper is to examine the surface oxide morphology resulting from the exposures. It was found that the material surface was enriched in rare earth silicate phases in combustion environments when compared to the oxides formed on materials exposed in dry oxygen. However, the in situ formation of rare earth disilicate phases offered little additional protection from the volatilization of silica observed in combustion environments. It was concluded that externally applied environmental barrier coatings are needed to protect additive-containing silicon nitride materials from volatilization reactions in combustion environments. Introduction Si3N4 is proposed for use as components, such as vanes, in turbine applications. Tens of thousands of hours of life are needed for both land-based turbines and aeropropulsion applications. Additive-containing SisN4 materials are

Opila, Elizabeth J.↗
NASA NTRS2007

High Pressure Burner Rig Testing of Advanced Environmental Barrier Coatings for Si3N4 Turbine Components

Advanced thermal and environmental barrier coatings are being developed for Si3N4 components for turbine engine propulsion applications. High pressure burner rig testing was used to evaluate the coating system performance and durability. Test results demonstrated the feasibility and durability of the coating component systems under the simulated engine environments.

Zhu, Dongming↗
NASA NTRS1974

Mechanical behavior of polycrystalline ceramics: Brittle fracture of SiC-Si3N4 materials

Various properties of ceramic materials were investigated. Magnesium oxide and the role of anion impurities were investigated together with the slow crack growth in silicon nitride-silicon carbide ceramics. The oxide program involved development of fabrication techniques for anion doped materials and evaluation of the role of these anions in the hot pressing response, grain boundary diffusion of nickel doped material, grain boundary microhardness, and grain growth. The carbide-nitride work employed commercial materials and the research involved evaluation of a recently reported technique for study of slow crack growth and the development of data for these commercial materials.

Leipold, M. H.↗
NASA NTRS1974

Mechanical behavior of polycrystalline ceramics: Brittle fracture of SiC-Si3N4 materials

The first study area involved magnesium oxide and the role of anion impurities, while the second area was directed toward slow crack growth in silicon nitride-silicon carbide ceramics. The oxide program involved development of fabrication techniques for anion doped materials and evaluation of the role of these anions in the hot pressing response, grain boundary diffusion of nickel doped material, grain boundary microhardness, and grain growth.

Leipold, M. H.↗