Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STIRRING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Impact of initial temper of base metal on microstructure and mechanical properties of friction stir welded AA 7055 alloy

Highlights: • Friction stir welded 7055-T4 alloy exhibits higher tensile properties than T6 alloy. • Friction stir welded 7055-T4 alloy exhibits more uniform hardness distribution. • Some regions in heat affected zone have higher hardness than base metal in T4-joint. • Effect of initial temper on precipitate evolution in different zones is discussed. AA 7055-T6 and AA 7055-T4 aluminium alloy sheets were friction stir welded to investigate the impact of initial base metal temper on microstructure, hardness and tensile properties of the joints. In the joint of alloy in T6 temper (T6-joint), the hardness of the weld zone is lower than that of base metal; in the joint of alloy in T4 temper (T4-joint), however, some regions in the heat affected zone exhibit higher hardness than base metal. The weld nugget zone in T6-joint exhibits slightly lower hardness compared with that in T4-joint. The hardness minima is slightly higher in T4-joint than in T6-joint. T4-joint exhibits higher yield strength, ultimate tensile strength and elongation compared with T6-joint. Based on microstructure examination by transmission electron microscopy, the impact of initial precipitate state on precipitation behavior in the weld nugget zone, thermo-mechanically affected zone and heat affected zone during friction stir welding and mechanical properties of the joints is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Aluminium composites prepared by laser cladding assisted by friction stir processing

Abstract A laser cladding and friction stir processing hybrid method was employed to produce an Al matrix composite layer. The microstructure, phase composition, microhardness and conductivity of the composites were investigated. A laser cladding layer with a thickness of approximately 200 μ m was prepared on a 1060 aluminium plate and it was broken up and distributed on the Al matrix after friction stir processing. The particle/Al interfaces exhibited extremely good interfacial integrity. Microstructural observations revealed that an obvious in situ reaction occurred at the particle/Al interfaces, which effectively improved the bonding between the reinforcement phase and the matrix. TEM analysis and selected area diffraction enabled the identification of the intermetallic compounds and confirmed them to be Al 5 Fe 2 and Al 3 Fe. The average microhardness values of the friction stir processed composites reached approximately 85 HV. The electrical resistivity of the friction stir processed composites is slightly higher than that of the aluminium matrix.

Wei, Yanni (ORCID:0000000244443642)↗
NASA NTRS2000

Demonstration of a Large-Scale Tank Assembly via Circumferential Friction Stir Welds

A collaborative effort between NASA/Marshall Space Flight Center and the Michoud Unit of Lockheed Martin Space Systems Company was undertaken to demonstrate assembly of a large-scale aluminum tank using circumferential friction stir welds. The hardware used to complete this demonstration was fabricated as a study of near-net- shape technologies. The tooling used to complete this demonstration was originally designed for assembly of a tank using fusion weld processes. This presentation describes the modifications and additions that were made to the existing fusion welding tools required to accommodate circumferential friction stir welding, as well as the process used to assemble the tank. The tooling modifications include design, fabrication and installation of several components. The most significant components include a friction stir weld unit with adjustable pin length capabilities, a continuous internal anvil for 'open' circumferential welds, a continuous closeout anvil, clamping systems, an external reaction system and the control system required to conduct the friction stir welds and integrate the operation of the tool. The demonstration was intended as a development task. The experience gained during each circumferential weld was applied to improve subsequent welds. Both constant and tapered thickness 14-foot diameter circumferential welds were successfully demonstrated.

Jones, Clyde S.↗
NASA NTRS2002

Friction-Stir Welding of Aluminum For the Space Program

The Marshall Space Flight Center is developing and characterizing the friction stir welding process for the Space Shuttle and other space programs. This revolutionary process, invented and patented by The Weld Institute in England, offers tremendous advantages for joining aluminum for high performance applications. It is particularly suited for advanced aluminum-lithium alloys, such as 2195, the primary structural alloy used in the External Tank. The friction stir welding process joins metals with minimal heat input, resulting in high-strength joints with high ductility. It is a simple process to demonstrate using a common milling machine for sample parts, but relatively expensive to implement on large-scale hardware, due to the high cost of tooling needed to handle the high forging pressures characteristic of the process. Recent developments at the Marshall Space Flight Center have demonstrated friction stir welding on linear joints up to 5 meters (15 ft.), with material thickness ranging between 2.5 mm and 16.5 mm (0.100" to 0.650"). High efficiency weld joints have been produced in aluminum from the 2000, 5000, and 6000 series alloy systems. A "retractable pin tool" system was patented by MSFC that allows use of friction stir welding for joints with changing material thickness, and with less rigid tooling than previously considered. This presentation will describe the details of alloys welded to-date and technical advances under development at MSFC. These developments could have substantial benefit to industrial applications for welding aluminum.

Jones, Clyde S.↗
NASA NTRS2002

Deformation During Friction Stir Welding

Friction Stir Welding (FSW) is a solid state welding process that exhibits characteristics similar to traditional metal cutting processes. The plastic deformation that occurs during friction stir welding is due to the superposition of three flow fields: a primary rotation of a radially symmetric solid plug of metal surrounding the pin tool, a secondary uniform translation, and a tertiary ring vortex flow (smoke rings) surrounding the tool. If the metal sticks to the tool, the plug surface extends down into the metal from the outer edge of the tool shoulder, decreases in diameter like a funnel, and closes up beneath the pin. Since its invention, ten years have gone by and still very little is known about the physics of the friction stir welding process. In this experiment, an H13 steel weld tool (shoulder diameter, 0.797 in; pin diameter, 0.312 in; and pin length, 0.2506 in) was used to weld three 0.255 in thick plates. The deformation behavior during friction stir welding was investigated by metallographically preparing a plan view sections of the weldment and taking Vickers hardness test in the key-hole region.

Henry J. White↗
NASA NTRS2006

Heat Treatment of Friction-Stir-Welded 7050 Aluminum Plates

A method of heat treatment has been developed to reverse some of the deleterious effects of friction stir welding of plates of aluminum alloy 7050. This alloy is considered unweldable by arc and high-energy-density beam fusion welding processes. The alloy can be friction stir welded, but as-welded workpieces exhibit low ductility, low tensile and yield strengths, and low resistance to stress corrosion cracking. Heat treatment according to the present method increases tensile and yield strengths, and minimizes or eliminates stress corrosion cracking. It also increases ductility. This method of heat treatment is a superior alternative to a specification-required heat treatment that caused the formation of large columnar grains, which are undesired. Workpieces subjected to the prior heat treatment exhibited elongations <2 percent, and standard three-point bend specimens shattered. The development of the present heat treatment method was guided partly by the principles that (1) by minimizing grain sizes and relieving deformation stresses, one can minimize or eliminate stress corrosion cracking and (2) the key to maximizing strength and eliminating residual stresses is to perform post-weld solution heating for as long a time as possible while incurring little or no development of large columnar grains in friction stir weld nuggets. It is necessary to perform some of the solution heat treatment (to soften the alloy and improve machine welding parameters) before welding. The following is an example of thickness- dependent pre- and post-weld heat treatments according to the present method: For plates 0.270 in. (approx.6.86 mm) thick milled from plates 4.5 in. (114.3 mm) thick, perform pre-weld solution heating at 890 F (477 C) for 1 hour, then cool in air. After friction stir welding, perform solution heating for 10 minutes, quench, hold at room temperature for 96 hours, then age at 250 F (121 C) for 5 hours followed by 325 F (163 C) for 27 hours.

Petter, George E.↗
DOE OSTI2015

HEAT INPUT AND POST WELD HEAT TREATMENT EFFECTS ON REDUCED-ACTIVATION FERRITIC/MARTENSITIC STEEL FRICTION STIR WELDS

Reduced-activation ferritic/martensitic (RAFM) steels are an important class of structural materials for fusion reactor internals developed in recent years because of their improved irradiation resistance. However, they can suffer from welding induced property degradations. In this paper, a solid phase joining technology friction stir welding (FSW) was adopted to join a RAFM steel Eurofer 97 and different FSW parameters/heat input were chosen to produce welds. FSW response parameters, joint microstructures and microhardness were investigated to reveal relationships among welding heat input, weld structure characterization and mechanical properties. In general, FSW heat input results in high hardness inside the stir zone mostly due to a martensitic transformation. It is possible to produce friction stir welds similar to but not with exactly the same base metal hardness when using low power input because of other hardening mechanisms. Further, post weld heat treatment (PWHT) is a very effective way to reduce FSW stir zone hardness values.

Tang, Wei↗
DOE OSTI2018

Hybrid friction stir welding for dissimilar materials through electro-plastic effect

A hybrid Friction Stir Welding approach and device for dissimilar materials joining employing Electro-Plastic Effect. The approach and device include an introduction of high density, short period current pulses into traditional friction stir welding process, which therefore can generate a localized softened zone in the workpiece during plastic stirring without significant additional temperature increase. This material softened zone is created by high density current pulses based on Electro-Plastic Effect and will move along with the friction stir welding tool. Smaller downward force, larger processing window and better joint quality for dissimilar materials are expected to be achieved through this hybrid welding technique.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Friction stirring interlocking of dissimilar materials

A method for solid state joining of dissimilar materials using a friction stir welding device wherein a pin is inserted through an aperture defined in a first material and a second material to hold the materials together and then held in place by friction stir welding a portion of the pin to a material adjacent said pin, or by friction stir welding a cap or plug that holds the pin in place to the adjacent material. The result is a connection or join wherein the central portion of the pin is not friction stir welded but the portions holding the pin in place (the ends or caps) generally are.

Whalen, Scott A.↗
DOE OSTI2022

Friction Stir Welding – an Advanced Approach to Repair Nuclear Power Plant Components

Solid phase joining technique friction stir welding (FSW) has been shown to mitigate helium-related issues in fusion welding of irradiated steels. Here, we present detailed characterization results of the first friction stir weld of an irradiated 304L stainless steel (SS) coupon contained 5.2 atomic parts per million (appm) helium. Scanning electron microscopy (SEM) was used to characterize a cross section specimen removed from the friction stir weld. No macro helium induced crack was observed at the analyzed cross-section, and only 1 – 1.5 µm size pores were found in the stir zone (SZ) and the thermal-mechanical affected zone (TMAZ). Moreover, some minor helium aggregations (Maximum ~20 µm in length) appeared along grain boundaries inside the TMAZ. Thereafter, miniature tensile specimens were extracted from the SZ, TMAZ and heat affected zone (HAZ), and base metal (BM) and tested. All welded specimens showed high total elongations (> 60%) and strengths (> 75% BM strengths). Overall, the weld made by FSW showed much better results comparing with traditional fusion welding on irradiated SS.

Tang, Wei↗
DOE OSTI2019

Advances in Dissimilar Metals Joining through Temperature Control of Friction Stir Welding

Lightweighting of vehicles and portable structures is an important undertaking. Multi-material design is required to achieve conflicting design targets such as cost, stiffness, and weight. Friction stir welding (FSW) variants, such as friction stir dovetailing and friction stir scribe, are enabling technologies for joining of dissimilar metals. This work shows that FSW variants are capable of joining aluminum to steel. Characteristics of metallurgical bonding at the dissimilar material interface are strongly affected by weld temperature. Control of FSW process temperature enables metallurgical bonding with suppressed formation of intermetallics at the dissimilar material interface resulting in improved mechanical properties relative to competing techniques. Temperature control is a powerful tool for process development and to ensure weld quality of dissimilar material welds.

Aluminum to Steel Joining, Friction stir welding, ↗
DOE OSTI2017

Role of Mechanical Stirring of Al-Mg Melt in the Healing of Bifilm Defect

The effect of mechanical stirring of aluminum melts containing 0.3, 0.7, and 4.5 wt pct Mg with a graphite rotor with different rotation speeds of 85 and 220 RPM on the behavior of bifilms was investigated using a reduced pressure test. The results showed that the mechanical stirring at 85 RPM accelerated the healing of the bifilms by increasing the rate of formation of cracks on the bifilms and hence accelerated the consumption of their atmosphere and provided enough Mg for the transformation of the alumina layers of the bifilms to spinel. Mechanical stirring with a high speed of 220 RPM caused aspiration of the surface oxide into the melt to form new bifilms which counteracted the healing of the previously presented bifilms.

36 MATERIALS SCIENCE↗
DOE OSTI2017

A Review of Permanent Magnet Stirring During Metal Solidification

Rather than using conventional electromagnetic stirring (EMS) with three-phase alternating current, permanent magnet stirring (PMS), based on the use of sintered NdFeB material which has excellent magnetic characteristics, can be employed to generate a magnetic field for the stirring of liquid metal during solidification. Recent experience with steel casting indicates that PMS requires less than 20 pct of the total energy compared with EMS. Despite the excellent magnetic density properties and low power consumption, this relatively new technology has received comparatively little attention by the metal casting community. This paper reviews simulation modeling, experimental studies, and industrial trials of PMS conducted during recent years. With the development of magnetic simulation software, the magnetic field and associated flow patterns generated by PMS have been evaluated. Based on the results obtained from laboratory experiments, the effects of PMS on metal solidification structures and typical defects such as surface pinholes and center cavities are summarized. The significance of findings obtained from trials of PMS within the metals processing sector, including the continuous casting of steel, are discussed with the aim of providing an overview of the relevant parameters that are of importance for further development and industrial application of this innovative technology.

36 MATERIALS SCIENCE↗
DOE OSTI2019

A Review of Physical and Numerical Approaches for the Study of Gas Stirring in Ladle Metallurgy

This article presents a review of the research into gas stirring in ladle metallurgy carried out over the past few decades. Herein, the physical modeling experiments are divided into four major areas: (1) mixing and homogenization in the ladle; (2) gas bubble formation, transformation, and interactions in the plume zone; (3) inclusion behavior at the steel–slag interface and in the molten steel; and (4) open eye formation. Several industrial trials have also been carried out to optimize gas stirring and open eye formation. Approaches for selecting criteria for scaling to guarantee flow similarity between industrial trials and physical modeling experiments are discussed. To describe the bubble behavior and two-phase plume structure, four main mathematical models have been used in different research fields: (1) the quasi-single-phase model, (2) the volume of fluid (VOF) model, (3) the Eulerian multiphase (E–E) model, and (4) the Eulerian–Lagrangian (E–L) model. In recent years, the E–E model has been used to predict gas stirring conditions in the ladle, and specific models in commercial packages, as well as research codes, have been developed gradually to describe the complex physical and chemical phenomena. Furthermore, the coupling of turbulence models with multiphase models is also discussed. For physical modeling, some general empirical rules have not been analyzed sufficiently. Based on a comparison with the available experimental results, it is found that the mathematical models focusing on the mass transfer phenomenon and inclusion behaviors at the steel-slag interface, vacuum degassing at the gas–liquid interface, dissolution rate of the solid alloy at the liquid–solid interface, and the combination of fluid dynamics and thermodynamics need to be improved further. To describe industrial conditions using mathematical methods and improve numerical modeling, the results of physical modeling experiments and industrial trials must offer satisfactory validations for the improvement of numerical modeling.

36 MATERIALS SCIENCE↗
DOE OSTI2017

The Simulation of Precipitation Evolutions and Mechanical Properties in Friction Stir Welding with Post-Weld Heat Treatments

A finite element model of friction stir welding capable of re-meshing is used to simulate the temperature variations. Re-meshing of the finite element model is used to maintain a fine mesh resolving the gradients of the solution. The Kampmann–Wagner numerical model for precipitation is then used to study the relation between friction stir welds with post-weld heat treatment (PWHT) and the changes in mechanical properties. Results indicate that the PWHT holding time and PWHT holding temperature need to be optimally designed to obtain FSW with better mechanical properties. Higher precipitate number with lower precipitate sizes gives higher strength in the stirring zone after PWHT. The coarsening of precipitates in HAZ are the main reason to hinder the improvement of mechanical property when PWHT is used.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of a Zinc Interlayer on a Cu/Al Lap Joint in Ultrasound-Assisted Friction Stir Welding

This study proposes a welding process, ultrasound-assisted friction stir welding of dissimilar Al/Cu metals. Zinc foil is melted using the heat generated by a pinless stirring tool, and the molten intermediate layer is stirred by ultrasonic cavitation to achieve an effective connection. The metallurgical reaction behavior of the joint under the action of the sound field was studied, and the effects of different microstructures on the joint performance were analyzed. Specifically, the following observations were reported in this study: (1) When ultrasound assistance was used, the cavitation effect changed the brittle intermetallic compounds of Al{sub 2}Cu from a continuous distribution to a block distribution, and the mechanical properties of the joint were greatly improved; (2) the effects of the thickness of the zinc were also determined. The results showed that the highest shear tensile force was obtained when the thickness of the zinc foil was 0.2 mm. When the thickness was 0.3 mm, the ultrasound effect was weakened. The copper-side interface generated a zigzag-shaped Al{sub 4.2}Cu{sub 3.2}Zn{sub 0.7} layer with a thickness of 3.4 μm and had a continuous distribution. Increasing the thickness of the zinc to 0.5 mm, however, drastically decreased the mechanical properties of the joint due to incomplete melting of the zinc layer.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of Raster Pattern Spacing and Direction for Friction Stir Additive Manufacturing of Al-5083

Friction stir additive manufacturing (FSAM) is a sheet-lamination based additive manufacturing technique. In addition to the traditional factors that govern the friction stir process-structure-property relationship, the processing history is convoluted by the in-plane raster pattern and repeated thermal cycling from subsequent layers. This can lead to complex thermal gradients within the workpiece and reprocessing of material. Here, this work aims to understand the impact of raster pattern spacing and direction on the microstructure and properties during friction stir additive manufacturing of Al-5083. Control of the raster spacing can lead to an increase in hardness of up to 18% from the base material and defect-free joining. These results are then directly demonstrated at the component-scale for FSAM of Al-5083.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Stress characterization for friction-stir-welded electric vehicle battery trays with application of neutron diffraction

The battery tray is an essential component that protects and controls battery-cell temperatures in electric and plug-in hybrid vehicles. The functional stress limit of the battery tray heavily depends on the residual stress acquired from the manufacturing process. Consequently, exceeding the stress limit of the battery tray during operation could compromise the battery-cell banks and may risk the vehicle's safety. Hence, understanding residual stress formation is vital for design and safety concerns. Here, in the current study, AA 6061-plates were friction stir welded to an A365 high-pressure die-cast battery tray to create sealed coolant channels in the battery tray. However, this multi-material lap friction stir weld introduces residual stress into the battery tray, resulting in distortion. This distortion was mitigated using burnishing or coining operations, though straightening the battery tray had initially unknown effects on the residual stress. Therefore, neutron diffraction was utilized to characterize residual stresses after straightening. The results indicate that the friction stir welding (FSW) operation generated residual stresses exceeding the yield strength of the material, consequently deforming the battery tray by ±3 mm from the pre-weld geometry. The burnishing operation reduced the residual stresses below the material's yield strength while restoring the tray to within ±0.75 mm of the pre-weld geometry. Similarly, the coining operation restored the battery tray to within ±0.75 mm of the pre-weld geometry, however, increasing the number of locations where the residual stress exceeds the yield strength of the material.

36 MATERIALS SCIENCE↗