Results for “SLS” — Page 5

NASA NTRS2015

SLS Scale Model Acoustic Test Liftoff Results and Comparisons

The liftoff phase induces acoustic loading over a broad frequency range for a launch vehicle. These external acoustic environments are then used in the prediction of internal vibration responses of the vehicle and components which result in the qualification levels. Thus, predicting these liftoff acoustic (LOA) environments is critical to the design requirements of any launch vehicle. If there is a significant amount of uncertainty in the predictions or if acoustic mitigation options must be implemented, a subscale acoustic test is a feasible design phase test option to verify the LOA environments. The NASA Space Launch System (SLS) program initiated the Scale Model Acoustic Test (SMAT) to verify the predicted SLS LOA environments.

Houston, Janice↗

NASA NTRS2016

Forward Skirt Structural Testing on the Space Launch System (SLS) Program

Introduction: (a) Structural testing was performed to evaluate Space Shuttle heritage forward skirts for use on the Space Launch System (SLS) program, (b) Testing was required because SLS loads are approximately 35% greater than shuttle loads; and (c) Two forwards skirts were tested to failure.

Lohrer, Joe↗

NASA NTRS2016

Forward Skirt Structural Testing on the Space Launch System (SLS) Program

Structural testing was performed to evaluate heritage forward skirts from the Space Shuttle program for use on the Space Launch System (SLS) program. One forward skirt is located in each solid rocket booster. Heritage forward skirts are aluminum 2219 welded structures. Loads are applied at the forward skirt thrust post and ball assembly. Testing was needed because SLS ascent loads are roughly 40% higher than Space Shuttle loads. Testing objectives were to determine margins of safety, demonstrate reliability, and validate analytical models. Two forward skirts were structurally tested using the test configuration. The test stand applied loads to the thrust post. Four hydraulic actuators were used to apply axial load and two hydraulic actuators were used to apply radial and tangential loads. The first test was referred to as FSTA-1 (Forward Skirt Structural Test Article) and was performed in April/May 2014. The purpose of FSTA-1 was to verify the ultimate capability of the forward skirt subjected to ascent ultimate loads. Testing consisted of two liftoff load cases taken to 100% limit load followed by an ascent load case taken to 110% limit load. The forward skirt was unloaded to no load after each test case. Lastly, the forward skirt was tested to 140% limit and then to failure using the ascent loads. The second test was referred to as FSTA-2 and performed in July/August of 2014. The purpose of FSTA-2 was to verify the ultimate capability of the forward skirt subjected to liftoff ultimate loads. Testing consisted of six liftoff load cases taken to 100% limit load followed by the six liftoff cases taken to 140% limit load. Two ascent load cases were then tested to 100% limit load. The forward skirt was unloaded to no load after each test case. Lastly, the forward skirt was tested to 140% limit and then to failure using the ascent loads. The forward skirts on FSTA-1 and FSTA-2 successfully carried all applied liftoff and ascent load cases. Both FSTA-1 and FSTA-2 were tested to failure by increasing the ascent loads. Failure occurred in the forward skirt thrust post radius. The forward skirts on FSTA-1 and FSTA-2 had nearly identical failure modes. FSTA-1 failed at 1.72 times limit load and FSTA-2 failed at 1.62 times limit load. This difference is primarily attributed to variation in material properties in the thrust post region. Test data were obtained from strain gages, deflection gages, ARAMIS digital strain measurement, acoustic emissions, and high-speed video. Strain gage data and ARAMIS strain were compared to finite element (FE) analysis predictions. Both the forward skirt and tooling were modeled. This allows the analysis to simulate the loading as close as possible to actual test configuration. FSTA-1 and FSTA-2 were instrumented with over 200 strain gages to ensure all possible failure modes could be captured. However, it turned out that three gages provided critical strain data. One was located in the post bore and two on the post radius. More gages were not specified due to space limitations and the desire to not interfere with the use of the ARAMIS system on the post radius. Measured strains were compared to analysis results for the load cycle to failure. Note that FSTA-1 gages were lost before failure was reached. FSTA-2 gages made it to the failure load but one of the radius gages was lost before testing began. This gage was not replaced because of the time and cost associated with disassembly of the test structure. Correlation to analysis was excellent for FSTA-1. FSTA-2 was not quite as good because there was more residual strain from previous load cycles. FSTA-2 was loaded and unloaded with 12 liftoff cases and two ascent cases before taking the skirt to failure. FSTA-1 only had two liftoff cases and one ascent case before taking the skirt to failure. The ARAMIS system was used to determine strain at the post radius by processing digital images of a speckled paint pattern. Digital cameras recorded images of the speckled paint pattern. ARAMIS strain results for FSTA-2 just prior to failure. Note a high strain location develops near the left side. This high strain compares well to analysis prediction for both FSTA-1 and FSTA-2. The strain at this location was also plotted versus limit load. Both FSTA-1 and FSTA-2 had excellent correlation between ARAMIS and analysis strains. Acoustic emission (AE) sensors were used to monitor for damage formation that may occur during testing (e.g., crack formation and growth or propagation). AE was very important because after disassembly of FSTA-1, a crack was observed in the ball fitting radius. The ball fitting did not crack on FSTA-2. AE data was used to reconstruct when the crack occurred. The AE energy versus time plot for FSTA. The energy increased considerably at 850 seconds (152% limit load), indicating a crack could have formed at this point. The only visual evidence found that could have corresponded to this was the crack that initiated in the ball fitting. The cracks in the forward skirt aluminum structures would likely have been lower energy due to a lower modulus and all that were found after failure correlated to occurring after the initial crack in the post radius. This was verified by high-speed cameras used to record the failure.

Lohrer, J. D.↗

NASA NTRS2016

Assessment of the Orion-SLS Interface Management Process in Achieving the EIA 731.1 Systems Engineering Capability Model Generic Practices Level 3 Criteria

NASA is currently developing the next generation crewed spacecraft and launch vehicle for exploration beyond earth orbit including returning to the Moon and making the transit to Mars. Managing the design integration of major hardware elements of a space transportation system is critical for overcoming both the technical and programmatic challenges in taking a complex system from concept to space operations. An established method of accomplishing this is formal interface management. In this paper we set forth an argument that the interface management process implemented by NASA between the Orion Multi-Purpose Crew Vehicle (MPCV) and the Space Launch System (SLS) achieves the Level 3 tier of the EIA 731.1 System Engineering Capability Model (SECM) for Generic Practices. We describe the relevant NASA systems and associated organizations, and define the EIA SECM Level 3 Generic Practices. We then provide evidence for our compliance with those practices. This evidence includes discussions of: NASA Systems Engineering Interface (SE) Management standard process and best practices; the tailoring of that process for implementation on the Orion to SLS interface; changes made over time to improve the tailored process, and; the opportunities to take the resulting lessons learned and propose improvements to our institutional processes and best practices. We compare this evidence against the practices to form the rationale for the declared SECM maturity level.

Jellicorse, John J.↗

NASA NTRS2017

SLS Overview and Progress

Space Launch System will be able to offer payload accommodations with five times more volume than any contemporary launch vehicle Payload fairings of up to 10-meter diameter are being studied Space Launch System will offer an initial capability of greater than 70 metric tons to low Earth orbit; current U.S. launch vehicle maximum is 28 t Evolved version of SLS will offer Mars-enabling capability of greater than 130 metric tons to LEO SLS offers reduced transit times to the outer solar system by half or greater Higher characteristic energy (C3) also enables larger payloads to destination

Honeycutt, John↗

NASA NTRS2017

Overview of SLS Aeroacoustic Environment Development

The Space Launch System (SLS) ascent aeroacoustic environments provide the externally driven noise levels predicted for vehicle ascent during transonic and supersonic flight, and serve as an important input for component and secondary structure vibroacoustic design criteria. This aerodynamically induced noise is predominantly generated by unsteady flow within the local boundary layer due to free stream interaction with the outer mold line (OML). Additional sources are shear flow interactions, shocks, protuberance flows, and wake flows. This presentation provides an overview of the aeroacoustics discipline along with the SLS environment development process, including wind tunnel testing and general data reduction methods. The state of the discipline is also presented with a summary of aeroacoustic measurement and computational techniques currently on the horizon.

Steva, Thomas↗

NASA NTRS2018

Methodologies for Verification and Validation of Space Launch System (SLS) Structural Dynamic Models

Responses to challenges associated with verification and validation (V&V) of Space Launch System (SLS) structural dynamics models are presented in this paper. Four methodologies addressing specific requirements for V&V are discussed. (1) Residual Mode Augmentation (RMA), which has gained acceptance by various principals in the NASA community, defines efficient and accurate FEM modal sensitivity models that are useful in test-analysis correlation and reconciliation and parametric uncertainty studies. (2) Modified Guyan Reduction (MGR) and Harmonic Reduction (HR, introduced in 1976), developed to remedy difficulties encountered with the widely used Classical Guyan Reduction (CGR) method, are presented. MGR and HR are particularly relevant for estimation of "body dominant" target modes of shell-type SLS assemblies that have numerous "body", "breathing" and local component constituents. Realities associated with configuration features and "imperfections" cause "body" and "breathing" mode characteristics to mix resulting in a lack of clarity in the understanding and correlation of FEM- and test-derived modal data. (3) Mode Consolidation (MC) is a newly introduced procedure designed to effectively "de-feature" FEM and experimental modes of detailed structural shell assemblies for unambiguous estimation of "body" dominant target modes. Finally, (4) Experimental Mode Verification (EMV) is a procedure that addresses ambiguities associated with experimental modal analysis of complex structural systems. Specifically, EMV directly separates well-defined modal data from spurious and poorly excited modal data employing newly introduced graphical and coherence metrics.

Coppolino, Robert N.↗

NASA NTRS2018

Quality Assurance Surveillance Tool Designed for SLS EM-1 Certificate of Flight Readiness

Exploration Mission-1 (EM-1) is an uncrewed mission that is launching on the Space Launch System (SLS) Block 1 vehicle. This is a critical flight test for the agency's human deep space exploration goals. Exploration Ground Systems (EGS) Quality (SA-F2) is responsible for providing Quality Assurance Surveillance Plans (QASPs) for NASA contracts and facilities. A QASP assures products and services are provided to EGS in accordance with the contract requirements. In order to encapsulate the multiple KSC Safety and Mission Assurance surveillance and audit activities that need to be accomplished specifically for EM-1 Certificate of Flight Reediness (CoFR), a QASP tool needed to be implemented. This tool would be able to intuitively track Work Authorization Documents (WADs) under development by Test Operations Support Contract (TOSC), reviewed and accepted WADs, Government Mandatory Inspection Points (GMIPs), Nonconformances (NCs), Material Review Board (MRB) Status, Corrective Actions, Alterations, Deviations, and Waivers for flight hardware and Ground Support Equipment (GSE). This would help ensure that all SLS EM-1 flight hardware and related GSE surveillances and requirements are being recognized and completed with zero constraints identified for the mission.

Morris, Patrick↗

NASA NTRS2019

Booster Obsolescence and Life Extension (BOLE) for Space Launch System (SLS)

A human mission to the moon and Mars is the stated space exploration goal of the United States and the international community. To achieve these goals, NASA is developing the Space Launch System (SLS) and the Orion crew capsule as key elements in the architecture for missions to the moon and Mars. As part of the SLS Booster Obsolescence and Life Extension (BOLE) program, Northrop Grumman Innovation Systems is working to address booster obsolescence issues in design and manufacturing. The upgraded boosters will also provide increased performance that will benefit future lunar campaigns, science missions, and the eventual Mars campaign.

Tobias, Mark E.↗

NASA NTRS2020

Booster Obsolescence and Life Extension (BOLE) for Space Launch System (SLS)

A human mission to the moon and Mars is the stated space exploration goal of the United States and the international community. To achieve these goals, NASA is developing the Space Launch System (SLS) and the Orion crew capsule as key elements in the architecture for missions to the moon and Mars. As part of the SLS Booster Obsolescence and Life Extension (BOLE) program, Northrop Grumman Space Systems is working to address booster obsolescence issues in design and manufacturing. The upgraded boosters will also provide increased performance that will benefit future lunar campaigns, science missions, and the eventual Mars campaign.

Tobias, Mark E.↗

NASA NTRSDate not supplied

Analysis and Application of Novel and Heritage Acceleration Limiting Algorithms for SLS on Ascent

National Aeronautics and Space Administration (NASA) is currently building the Space Launch System (SLS) Block-1 launch vehicle, to be used as the crewed heavy-lift vehicle for the Artemis series of missions. The SLS Block-1 guidance subsystem utilizes a nonlinear algorithm derived from Shuttle heritage for limiting the vehicle’s induced maximum axial acceleration during ascent flight, known as g-limiting. Even though g-limiting has demonstrated stability and robustness through several design analysis cycles and the extensive Shuttle flight history, there are no available documents that demonstrate that this algorithm has been proven stable through conventional controls stability analysis. This paper highlights the non-linear nature of g-limit, presents an alternative methodology to employ a linear version of this algorithm, performs assessment of selected linear gains using classical stability analysis and, conducts a comparison of both approaches through Six Degrees-of-Freedom (6-DOF) Monte Carlo (MC) simulations.

Jason Everett↗

NASA NTRSDate not supplied

Fluid for Thought: SLS Rocket Aerodynamics featuring Pressure Sensitive Paint

Combining computer vision algorithms, state-of-the-art high-speed cameras, pressure sensitive paint (PSP) and transonic wind tunnel facilities, teams at NASA and Boeing study unsteady pressure over the Space Launch System (SLS) rocket model with unprecedented temporal and spatial data resolution. Post-processing visualizes pressure fluctuations over a 3D model by converting intensity data from videos of the wind tunnel test. Additionally, data analysis creates predictions of buffet forcing and aeroacoustic activity over the rocket body with the accuracy of a CFD model! The development of the technique will revolutionize aerodynamics research and reveal uncharted insights into fluid behavior and vehicle performance, enhancing aerospace technology and design as they advance. The talk will focus on the impact of the PSP technique on the SLS design and other potential aerospace applications, as well as lay out the experimental process, from wind tunnel test to insights from the data analysis.

Lucy Zhonghui Tang↗

NASA NTRS2017

Iris Deep-Space Transponder for SLS EM-1 CubeSat Missions

Several key design upgrades have been recently made to the Iris Deep-Space Transponder baselined to be used on secondary payload missions of the upcoming Space Launch System Exploration Mission One (SLS EM-1). The Iris Transponder is a reconfigurable software-defined radio (SDR) designed for missions requiring interoperability with NASA's Deep Space Network (DSN) on X-band frequencies (7.2 GHz uplink, 8.4 GHz downlink). The transponder provides radiometric tracking support with the DSN to provide navigational products for precise orbit determination while performing standard uplink and downlink communications in a CubeSat/SmallSat-applicable package size. The recent hardware changes include a volume reduction of 30% from previous models, with the main transponder unit weighing less than 1.0 kg, while maintaining total ionizing dose (TID) radiation tolerance of >23 krads (Si) for deep-space missions. Lab tests indicate maximum downlink rates of up to 6.25 Msps can be supported by the transponder in conventional BPSK modulation, but most SLS EM-1 CubeSat missions are link-performance limited to less than 256 kbps. A prototype unit of the flight production units has been assembled and various performance and characterization tests are underway. This talk discusses the key design aspects and specifications of the Iris Transponder and presents preliminary results from early testing of the assembled transponder.

Kobayashi, M. Michael↗

NASA NTRS2022

Unsteady Pressure Acquisition on the 1.75% Scale SLS Block 1B Cargo Liftoff Configuration

Time-varying pressure on the core of the Space Launch System (SLS) Block 1B Cargo vehicle was acquired using instrumentation typically used for steady, time averaged pressure. Resono Pressure Systems, Inc. in partnership with the University of Wyoming have developed a unique hardware and software system for measuring unsteady pressure, which was implemented in a large-scale wind tunnel test through a nonreimbursable Space Act Agreement with NASA. The technique was applied to 12 pressure ports on the 1.75% scale SLS wind tunnel model. Tubing lengths of approximately 14 inches separated the pressure transducer module from the pressure taps on the model surface, and surface-mount validation sensors (Kulites) were installed in close proximity to 5 of the 12 pressure ports. Up to about 500 Hz, the frequency response of pressure fluctuations agreed to within 1 dB of amplitude and 10° of phase difference compared to the simultaneously-acquired surface-mount transducers. Sample results using the reconstructed pressure from the full azimuthal ring of taps are presented.

unsteady pressure↗

NASA NTRSDate not supplied

Validation of Shadowgraph Spectral Analysis using an SLS Block 2 Wind-Tunnel Model

A flow quantification method has previously been developed that uses high-speed shadowgraph images to extract frequency content of a transonic flow field around a wind-tunnel model. In this method, a classical spectral analysis is performed on shadowgraph video pixels to identify their intensity fluctuation frequencies. The spatial change of the image intensity is related to the second derivative of the density gradient. Examining the change of the density gradient as a function of time can be used to understand the flow-field pressure fluctuations. Time-varying pressure measurements collected during a Space Launch System (SLS) unsteady aerodynamic test of an advanced Block 2 booster design are used to calibrate the shadowgraph-based measurements. The test was performed at the NASA Ames Research Center Unitary Plan Wind Tunnel 11- by 11-foot test section and investigated the aerodynamic environment downstream of candidate booster forward attachment hardware geometries of the SLS Block 2 Cargo configuration. Time-correlated shadowgraph video and model surface pressure measurements were acquired during the test and served as an ideal opportunity to calibrate and validate the shadowgraph image intensity method.

Shadowgraph↗

NASA NTRSDate not supplied

Validation of Shadowgraph Spectral Analysis using an SLS Block 2 Wind-Tunnel Model

A flow quantification method has previously been developed that uses high-speed shadowgraph images to extract frequency content of a transonic flow field around a wind-tunnel model. In this method, a classical spectral analysis is performed on shadowgraph video pixels to identify their intensity fluctuation frequencies. The spatial change of the image intensity is related to the second derivative of the density gradient. Examining the change of the density gradient as a function of time can be used to understand the flow-field pressure fluctuations. Time-varying pressure measurements collected during a Space Launch System (SLS) unsteady aerodynamic test of an advanced Block 2 booster design are used to calibrate the shadowgraph-based measurements. The test was performed at the NASA Ames Research Center Unitary Plan Wind Tunnel 11- by 11-foot test section and investigated the aerodynamic environment downstream of candidate booster forward attachment hardware geometries of the SLS Block 2 Cargo configuration. Time-correlated shadowgraph video and model surface pressure measurements were acquired during the test and served as an ideal opportunity to calibrate and validate the shadowgraph image intensity method.

Shadowgraph↗

NASA NTRSDate not supplied

Gimbal Bearing Friction in the SLS Core Stage Thrust Vector Control System

The Space Launch System (SLS) Core Stage Thrust Vector Control (TVC) system is comprised of eight mechanical feedback Shuttle heritage Type III TVC actuators that vector the four Shuttle heritage RS-25 engines about a Shuttle heritage gimbal block/bearing. The MSFC Controls community has long regarded gimbal friction to be a negligible effect on the overall control of gimbaled RS-25 engines. This is corroborated by Space Shuttle test and flight data that does not appear to show degraded effects, nor limit cycling at the end of the shuttle flight. For this reason, friction was not expected to be a driving factor of performance and control of the reused RS-25 engines aboard the SLS. However, after test data showed a large shift in frequency behavior and a highly damped step-response in the time series, there was further investigation into what could have caused this behavior. Heritage friction models used in previous gimbal and ball bearings were evaluated such as Coulomb, Dahl and LuGre, but the single degree of freedom friction models alone were not enough to explain the behavior and shifts seen in the test data. This paper presents the additional findings and modeling efforts regarding friction on the RS-25 engines. Using the Two Actuator Operational Simulation (TAOS), the difference from modeling separate friction degrees of freedom to coupled degrees of freedom was investigated to deduce the effects of one axis’s movement on the other. Next, due to the vibration environment, a modified LuGre model has been proposed that adds an additional term to decrease the friction coefficient at low engine velocity amplitudes. Lastly, the addition of the stiffness in each half of the gimbal bearing has increased modeling fidelity by also adding the effect on the gimbal bearing bending in compliance to both the friction torque on the surface of the gimbal bearing and the actuator force that is forcing the engine in a specified direction. Through these effects, the time and frequency domain behavior seen in test can be characterized accurately.

Friction↗

NASA NTRSDate not supplied

Gimbal Bearing Friction in the SLS Core Stage Thrust Vector Control System

The Space Launch System (SLS) Core Stage Thrust Vector Control (TVC) system is comprised of eight mechanical feedback Shuttle heritage Type III TVC actuators that vector the four Shuttle heritage RS-25 engines about a Shuttle heritage gimbal block/bearing. The MSFC Controls community has long regarded gimbal friction to be a negligible effect on the overall control of gimbaled RS-25 engines. This is corroborated by Space Shuttle test and flight data that does not appear to show degraded effects, nor limit cycling at the end of the shuttle flight. For this reason, friction was not expected to be a driving factor of performance and control of the reused RS-25 engines aboard the SLS. However, after test data showed a large shift in frequency behavior and a highly damped step-response in the time series, there was further investigation into what could have caused this behavior. Heritage friction models used in previous gimbal and ball bearings were evaluated such as Coulomb, Dahl and LuGre, but the single degree of freedom friction models alone were not enough to explain the behavior and shifts seen in the test data. This paper presents the additional findings and modeling efforts regarding friction on the RS-25 engines. Using the Two Actuator Operational Simulation (TAOS), the difference from modeling separate friction degrees of freedom to coupled degrees of freedom was investigated to deduce the effects of one axis’s movement on the other. Next, due to the vibration environment, a modified LuGre model has been proposed that adds an additional term to decrease the friction coefficient at low engine velocity amplitudes. Lastly, the addition of the stiffness in each half of the gimbal bearing has increased modeling fidelity by also adding the effect on the gimbal bearing bending in compliance to both the friction torque on the surface of the gimbal bearing and the actuator force that is forcing the engine in a specified direction. Through these effects, the time and frequency domain behavior seen in test can be characterized accurately.

Friction↗