Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Refilling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Developments in low-gravity cryogenic propellant acquisition and thermal control systems

Development programs are described for two low-gravity cryogenic propellant acquisition systems: a full-screen liner system, and a refillable start-tank. First, based on experimental LH2 screen flow data, the fluid-dynamic characteristics of an integrated screen/thermodynamic vent system were analyzed for a design compared to 17.5 cu fg supercritical life-support systems, and for a Tug orbital LH2/LQ2 resupply system. Second, the analysis, design, fabrication, and test of a 10 cu ft, annular-screen start-tank with a wall-mounted thermodynamic vent was performed. The test program demonstrated that the system expelled LH2 against 1-g and performed properly over a range of conditions.

Cady, E. C.↗
NASA NTRS1975

Fluctuations in O2 stores and gas exchange with passive changes in posture

The purpose of the present study is to determine the effects of changes in posture on oxygen transfer at the mouth and pulmonary capillary membrane and to observe concomitant subtle changes in ventilation under specified assumptions. Breath-by-breath calculations are carried out with a box-balloon spirometer and mass spectrometer. Measurements are made before, during, and after passive tilt to 60 deg and on return to recumbency after 10 min erect. It is found that from supine to upright oxygen stores in the lung increases rapidly and oxygen stores in the blood drops slowly, creating a net deficit in oxygen transfer at the mouth of 130 ml in 10 min. Changes in oxygen stores in the blood result from shifts in blood volume and flow more than from changes in cardiac output. Refilling of oxygen stores in the blood is found to cause transient hypoxia with substantial hyperpnea.

Loeppky, J. A.↗
NASA NTRS1976

Repair of fused silica platens

Refill/leveling technique, which consists of spreading slurry refill material to affected areas and then sanding until surfaces are flat, extends service life of platen up to 50 production cycles between downtime.

Heisman, R. M.↗
NASA NTRS1976

A local diffusion process associated with the sweeping of energetic particles by Io

A local, turbulent diffusion process which may rapidly refill the partial cavity of energetic particles created by Io's passage through a flux tube is discussed. A model is developed of Io's sweeping action on energetic particles in which a wake is formed behind the flux tube threading Io. It is shown to be possible that this wake contains an excess of positive charge, thereby creating an electric field. The particle drift produced by this field, coupled with the density gradient of energetic protons, can generate an instability. It is this instability that is responsible for the turbulent diffusion process. The sweeping of energetic particles is also discussed in relation to particle energy and pitch angle distribution.

Huba, J. D.↗
NASA NTRS1976

Solid-state growth of Si to produce planar surfaces

Paralleling the sophisticated control of Si and GaAs growth from fluid media, we demonstrate control of Si growth using a solid growth medium. Faceted dissolution pits were first produced in a Si substrate using standard photolithographic techniques and Al metallization. Si was then evaporated onto the cold structure, depositing as amorphous material. Upon heating, the amorphous Si migrated through the solid Al and grew rapidly in the faceted pits, typically refilling them flush with the surrounding substrate. Evidence that the rapid growth occurs only while the amorphous Si is dissolving into the Al is presented.

Boatright, R. L.↗
NASA NTRS1976

Deviation from a Maxwellian velocity distribution in regions of interstellar molecular hydrogen

The deviation from a Maxwellian velocity distribution caused by excitation of the J = 2 rotational level of parahydrogen (followed by radiative decay) in a molecular hydrogen gas is investigated. It is noted that inelastic collisions deplete the high-velocity tail of the distribution, while elastic collisions tend to refill it; the resulting steady-state distribution has a small depletion in the tail which slightly reduces the cooling rate of the gas. The elastic-collision transport is approximated by a continuous process, a simplified expression is obtained for the inelastic-collision operator, and the Boltzmann equation is then solved analytically. A correction to the inelastic-collision rate is evaluated, and it is found that the relative magnitude of the effect of tail depletion on the inelastic-collision rate is strongly temperature-dependent. The critical molecular density above which the J = 2 level deexcites by superelastic collisions is shown to be a weak function of temperature.

Gould, R. J.↗
NASA NTRS1977

Advanced combined iodine dispenser and detector

A total weight of 1.23 kg (2.7 lb), a total volume of 1213 cu m (74 cu in), and an average power consumption of 5.5W was achieved in the advanced combined iodine dispenser/detector by integrating the detector with the iodine source, arranging all iodinator components within a compact package and lowering the parasitic power to the detector and electronics circuits. These achievements surpassed the design goals of 1.36 kg (3.0 lb), 1671 cu m (102 cu in) and 8W. The reliability and maintainability were improved by reducing the detector lamp power, using an interchangeable lamp concept, making the electronic circuit boards easily accessible, providing redundant water seals and improving the accessibility to the iodine accumulator for refilling. The system was designed to iodinate (to 5 ppm iodine) the fuel cell water generated during 27 seven-day orbiter missions (equivalent to 18,500 kg (40,700 lb) of water) before the unit must be recharged with iodine crystals.

Lantz, J. B.↗
NASA NTRS1978

Filling of orbital fluid management systems

A study was performed with three objectives: (1) analyze fluid management system fill under orbital conditions; (2) determine what experimentation is needed; and (3) develop an experimental program. The fluid management system was a 1.06m (41.7 in) diameter pressure vessel with screen channel device. Analyses were conducted using liquid hydrogen and N2O4. The influence of helium and autogenous pressurization systems was considered. Analyses showed that fluid management system fill will be more difficult with a cryogen than with an earth storable. The key to a successful fill with cryogens is in devising techniques for filling without vent liquid, and removing trapped vapor from the screen device at tank fill completion. This will be accomplished with prechill, fill, and vapor condensation processes. Refill will require a vent and purge process, to dilute the residual helium, prior to introducing liquid. Neither prechill, chill, nor purge processes will be required for earth storables.

Merino, F.↗
NASA NTRS1978

Ionospheric and magnetospheric 'plasmapauses'

The locations of Explorer 45 plasmapause crossings are studied as a likely indicator of ionospheric and magnetospheric trough locations. Attention is given to vertical flows of H(+) ions in the light ion trough, as detected by the magnetic ion mass spectrometer aboard Isis 2 (which was operating in conjunction with Explorer 45 during August 1972). The possibility of an equatorial plasmapause is discussed, whose field lines map into the ionosphere at latitudes poleward of the H(+) density decrease, probably due to the refilling of magnetic flux tubes in the outer plasmasphere.

Grebowsky, J. M.↗
NASA NTRS1980

All-inorganic spark-chamber frame

Outgassing is reduced by using ceramic and glass materials exclusively. Frames are assembled from four beams with rabbeted ends. Only ceramic or glass adhesives are used, and printed circuit is applied by screen printing directly on beams. Inorganic frames provide stable spark-chamber operation without gas refill, useful in terrestrial gamma-ray studies, in high-energy physics research, and other applications.

Heslin, T. M.↗
NASA NTRS1979

The Apollo 17 drill core - Petrologic systematics and the identification of a possible Tycho component

Modal data support a five-unit stratigraphy for the Apollo 17 drill core. The upper unit E (0-22 cm depth) is marked by high content of fused soil, brown glass, and mare basalt fragments. This unit corresponds with a portion of the core excavated and refilled within the last 2 m.y. The underlying unit D (22071 cm depth) has a low abundance of fused soil (i.e., low maturity) and is rich in coarse (less than 200 microns) mare fragments. A large section of the core, unit C (71-224 cm depth), is finer-grained, more mature (richer in agglutinates), more feldspathic and has more highland lithic, mineral and glass fragments than unit D. The next underlying unit, B (224-256 cm depth), has yellow/colorless KREEP glasses with a high Si, low-alkali composition unlike the common Apollo 15 or Apollo 17 KREEP series. The petrologic (fused soil) and Is/FeO maturity of this layer is also lower than the units above and below. The deepest unit, A (256-284 cm depth), is marked by its relatively higher maturity and lower yellow/colorless KREEP glass content. The most prominent petrographic/stratigraphic indicators are the pyroxene-rich immature mare unit D and the abundance of KREEP glass in unit B. This KREEP glass is distinctive petrographically and compositionally, and is probably exotic to the Apollo 17 site. It is suggested here that the KREEP glass in unit B is derived from Tycho, which implies widespread distribution of KREEP on the lunar nearside.

Vaniman, D. T.↗
NASA NTRS1982

Recharging the Silicon Crucible in a Hot Furnace

"Melt recharger" adds raw silicon to crucible in crystal-growing furnace without disturbing inert-gas atmosphere or significantly lowering temperature of melt. Crucible-refill hopper is lowered into hot zone of crystal-pulling chamber through an isolation valve. Cable that supports hopper is fastened to cone-shaped stopper in bottom of hopper. Stopper moves out of opening in hopper, allowing part of polysilicon charge to drop into crucible.

Lane, R. L.↗
NASA NTRS1980

Mutiple Czochralski growth of silicon crystals from a single crucible

An apparatus for the Czochralski growth of silicon crystals is presented which is capable of producing multiple ingots from a single crucible. The growth chamber features a refillable crucible with a water-cooled, vacuum-tight isolation valve located between the pull chamber and the growth furnace tank which allows the melt crucible to always be at vacuum or low argon pressure when retrieving crystal or introducing recharge polysilicon feed stock. The grower can thus be recharged to obtain 100 kg of silicon crystal ingots from one crucible, and may accommodate crucibles up to 35 cm in diameter. Evaluation of the impurity contents and I-V characteristics of solar cells fabricated from seven ingots grown from two crucibles reveals a small but consistent decrease in cell efficiency from 10.4% to 9.6% from the first to the fourth ingot made in a single run, which is explained by impurity build-up in the residual melt. The crystal grower thus may offer economic benefits through the extension of crucible lifetime and the reduction of furnace downtime.

Lane, R. L.↗
NASA NTRS1981

Forming electrical interconnections through semiconductor wafers

An information processing system based on CMOS/SOS technology is being developed by NASA to process digital image data collected by satellites. An array of holes is laser drilled in a semiconductor wafer, and a conductor is formed in the holes to fabricate electrical interconnections through the wafers. Six techniques are used to form conductors in the silicon-on-sapphire (SOS) wafers, including capillary wetting, wedge extrusion, wire intersection, electroless plating, electroforming, double-sided sputtering and through-hole electroplating. The respective strengths and weaknesses of these techniques are discussed and compared, with double-sided sputtering and the through-hole plating method achieving best results. In addition, hollow conductors provided by the technique are available for solder refill, providing a natural way of forming an electrically connected stack of SOS wafers.

Anthony, T. R.↗
NASA NTRS1982

Collapse of large vapor bubbles

The refilling of propellant tanks while in a low-gravity environment requires that entrapped vapor bubbles be collapsed by increasing the system pressure. Tests were performed to verify the mechanism of collapse for these large vapor bubbles with the thermodynamic conditions, geometry, and boundary conditions being those applicable to propellant storage systems. For these conditions it was found that conduction heat transfer determined the collapse rate, with the specific bubble geometry having a significant influence.

Tegart, J.↗
NASA NTRS1982

Evaluation of candidate stirling engine heater tube alloys at 820 deg and 860 deg C

Seven commercial alloys were evaluated in Stirling simulator materials rigs. Five iron base alloys (N-155, A-286, Incoloy 800, 19-9DL, and 316 stainless steel), one nickel base alloy (Inconel 718), and one cobalt base alloy (HS-188) were tested in the form of thin wall tubing in a diesel fuel fired test rig. Tubes filled with hydrogen or helium at gas pressure of 21.6 MPa and temperatures of 820 and 860 C were endurance tested for 1000 and 535 hours, respectively. Results showed that under these conditions hydrogen permeated rapidly through the tube walls, thus requiring refilling during each five hour cycle. Helium was readily contained, exhibiting no measurable loss by permeation. Helium filled tubes tested at 860 C all exhibited creep-rupture failures within the 535 hour endurance test. Subsequent tensile test evaluation after removal from the rig indicated reduced room temperature ductility for some hydrogen-filled tubes compared to helium-filled tubes, suggesting possible hydrogen embrittlement in these alloys.

Misencik, J. A.↗
NASA NTRS1982

Ultimate intrinsic coercivity samarian-cobalt magnet. An Earth based feasibility study for Space Shuttle missions

Techniques for the electromagnetic containerless reaction of samarium with cobalt for the formation of samarium-cobalt alloys are summarized. The effort expended to reduce and instrument the oxygen partial pressure in the reaction chamber and coolant gas system are described as well as the experiments in which these improvements were shown to be partially effective. A stainless steel glove box capable of being evacuated to low 10 to the -6th torr pressure and refilled with ultra-pure argon was built and installed. Necessary accessories to perform SmCo5 powder preparation, compaction and subsequent encapsulation of the powder inside a hot isostatic pressing cannister were designed, built, and incorporated into the chamber. All accessories were tested for proper functioning inside the chamber. Using the facility, the first batch of densified SmCo5 powder was fabricated to near total density. Analysis of the densified compacts shows that oxygen contamination during fabrication was near zero.

Das, D.↗
NASA NTRS1982

Effects of fractional crystallization and cumulus processes on mineral composition trends of some lunar and terrestrial rock series

A plot of Mg of mafic minerals versus An of plagioclase in cumulate rocks from various lunar and terrestrial rock series shows each series to have a distinct curvilinear trend. The slopes of these trends vary from nearly vertical in the case of lunar anorthosites and Mg-norites to nearly horizontal in the case of gabbros from the mid-Atlantic ridge. Calculations based upon known major element partitioning between mafic minerals, plagioclase and subalkaline basaltic liquids indicate that fractional crystallization coupled with cotectic accumulation of mafic minerals and plagioclase will produce mineral composition trends on the Mg versus An diagram with slopes greater than 1 for cases where An is approximately greater than Mg. Furthermore, fractional crystallization of basaltic magmas with alkali concentrations approaching zero will produce near vertical Mg versus An trends. Therefore, the steep slopes of the lunar rock series are consistent with relatively simple fractionation processes. The relatively flat slope of mineral compositions from gabbros collected from the mid-Atlantic ridge at 26 deg N is inconsistent with simple fractionation processes, and calculations show that periodic refilling of a fractionating magma chamber with picritic magma cannot simply explain this flat slope either.

Longhi, J.↗