Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROTOR SYSTEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1949

Hovering and Low-Speed Performance and Control Characteristics of the Kaman Helicopter Rotor System as Determined on the Langley Helicopter Tower. TED No. NACA DE 205

An investigation has been conducted with the Langley helicopter tower to obtain basic performance and control characteristics of the Raman rotor system. Blade-pitch control is obtained in this configuration by utilizing an auxiliary flap to twist the blades. Rotor thrust and power required were measured for the hovering condition and over a range of wind velocities from 0 to 30 miles per hour. The control characteristics and the transient response of the rotor to various control movements were also measured. The hovering-performance data are presented as a survey of the wake velocities and the variation of torque coefficient with thrust coefficient. The power required for the test rotor to hover at a thrust of 1350 pounds and a rotor speed of 240 rpm is approximately 6.5 percent greater than that estimated for a conventional rotor of the same diameter and solidity. It is believed that most of this difference is caused by th e flap servomechanism. The reduction in total power required for sustentation of the single-rotor configuration tested at various wind velocities and at the normal operating rotor thrust was found to be similar to the theoretical and experimental results for ro tors with conventionally actuated pitch. The control effectiveness was determined as a function of rotor speed. Sufficient control was available to give a thrust range of 0 to 1500 pounds and a rotor tilt of plus or minus 7 degrees. The time lag between flap motion and blade-pitch response is approximately 0.02 to 0.03 second. The response of the rotor following the blade-pitch response is similar to that of a rotor with conventionally actuated pitch changes. The over-all characteristics of the rotor investigated indicate that satisfactory performance and control characteristics were obtained.

Carpenter, Paul J.↗
NASA NTRSDate not supplied

Exploring the Impact of Sideslip Angle on Acoustic Predictions of an Open Rotor System Using Scale-Resolving Simulations

The development of innovative open-rotor propulsion systems that meet performance, fuel efficiency, and noise standards for commercial use depends significantly on the availability of reliable and computationally efficient tools for aerodynamic performance and noise prediction.This investigation demonstrates the capability of the structured curvilinear overset gridComputational Fluid Dynamics solver within the Launch, Ascent, and Vehicle Aerodynamics framework to predict the aerodynamic and aeroacoustic characteristics of a Contra-RotatingOpen Rotor propulsion system under various sideslip angles. In this publication, results obtained using a Hybrid Reynolds-Averaged Navier-Stokes/Large Eddy Simulation-based scale-resolving turbulence closure approach are validated against existing experimental measurements including aerodynamic loads, moments, and tones.

AATT↗
NASA NTRS1977

Load and stability measurements on a soft-inplane rotor system incorporating elastomeric lead-lag dampers

An experimental investigation was conducted of the dynamic response and inplane stability associated with a new soft-inplane helicopter rotor. The unique feature of this rotor was the use of an internal elastomeric damper to restrain the blade inplane motion about the lead-lag hinge. The properties of the elastomer were selected to provide both a nominal first inplane frequency ratio of 0.65 and sufficient damping to eliminate the need for additional external damping sources to prevent ground resonance on a typical fuselage structure. For this investigation a 1/5-scale aeroelastic model was used to represent the rotor. The four-blade model had a diameter of 3.05 m (10 ft) and a solidity of 0.103. The first out-of-plane frequency ratio was 1.06. The model was tested in hover and in forward flight up to an advance ratio of 0.45. At each forward speed the rotor lift was varied up to simulated maneuver conditions. The measured rotor loads and response were within acceptable limits, and no adverse response qualities were observed. Moderate out-of-plane hub moments were measured, even for zero lift, to indicate the beneficial control power available for this design. Blade inplane stability testing indicated that the rotor system damping remained at moderate levels throughout the operating envelope.

Weller, W. H.↗
NASA NTRS1983

The N/Rev phenomenon in simulating a blade-element rotor system

When a simulation model produces frequencies that are beyond the bandwidth of a discrete implementation, anomalous frequencies appear within the bandwidth. Such is the case with blade element models of rotor systems, which are used in the real time, man in the loop simulation environment. Steady state, high frequency harmonics generated by these models, whether aliased or not, obscure piloted helicopter simulation responses. Since these harmonics are attenuated in actual rotorcraft (e.g., because of structural damping), a faithful environment representation for handling qualities purposes may be created from the original model by using certain filtering techniques, as outlined here. These include harmonic consideration, conventional filtering, and decontamination. The process of decontamination is of special interest because frequencies of importance to simulation operation are not attenuated, whereas superimposed aliased harmonics are.

Mcfarland, R. E.↗
NASA NTRS1983

The N/rev phenomenon in simulating a blade-element rotor system

When a simulation model produces frequencies that are beyond the bandwidth of a discrete implementation, anomalous frequencies appear within the bandwidth. Such is the case with blade element models of rotor systems, which are used in the real time, man in the loop simulation environment. Steady state, high frequency harmonics generated by these models, whether aliased or not, obscure piloted helicopter simulation responses. Since these harmonics are attenuated in actual rotorcraft (e.g., because of structural damping), a faithful environment representation for handling qualities purposes may be created from the original model by using certain filtering techniques, as outlined here. These include harmonic consideration, conventional filtering, and decontamination. The process of decontamination is of special interest because frequencies of importance to simulation operation are not attenuated, whereas superimposed aliased harmonics are.

Mcfarland, R. E.↗
NASA NTRS1990

Rotor systems research aircraft risk-reduction shake test

A shake test and an extensive analysis of results were performed to evaluate the possibility of and the method for dynamically calibrating the Rotor Systems Research Aircraft (RSRA). The RSRA airframe was subjected to known vibratory loads in several degrees of freedom and the responses of many aircraft transducers were recorded. Analysis of the transducer responses using the technique of dynamic force determination showed that the RSRA, when used as a dynamic measurement system, could predict, a posteriori, an excitation force in a single axis to an accuracy of about 5 percent and sometimes better. As the analysis was broadened to include multiple degrees of freedom for the excitation force, the predictive ability of the measurement system degraded to about 20 percent, with the error occasionally reaching 100 percent. The poor performance of the measurement system is explained by the nonlinear response of the RSRA to vibratory forces and the inadequacy of the particular method used in accounting for this nonlinearity.

Wellman, J. Brent↗
NASA NTRS1979

A simplified rotor system mathematical model for piloted flight dynamics simulation

The model was developed for real-time pilot-in-the-loop investigation of helicopter flying qualities. The mathematical model included the tip-path plane dynamics and several primary rotor design parameters, such as flapping hinge restraint, flapping hinge offset, blade Lock number, and pitch-flap coupling. The model was used in several exploratory studies of the flying qualities of helicopters with a variety of rotor systems. The basic assumptions used and the major steps involved in the development of the set of equations listed are described. The equations consisted of the tip-path plane dynamic equation, the equations for the main rotor forces and moments, and the equation for control phasing required to achieve decoupling in pitch and roll due to cyclic inputs.

Chen, R. T. N.↗
NASA NTRSDate not supplied

Computational Prediction of Broadband Noise from a Representative Unmanned Aerial System Rotor

This work details the application of a lattice-Boltzmann method–very-large-eddy simulation (LBM-VLES) employed by the software suite, PowerFLOW. This LBM-VLES simulation predicted the aeroacoustic noise emanating from a representative, small unmanned aircraft system rotor, namely, the DJI-9450 in a hover condition. Predicted total aerodynamic loading as well as 2D aerodynamic loading along discrete spanwise sections of a rotor blade were compared to lower fidelity predictions and experimental results acquired in the Structural Acoustic Loads and Transmission anechoic chamber facility at the NASA Langley Research Center. The total acoustic spectra were decomposed into tonal and broadband components, which showed that broadband noise was a dominant contributor above 1 kHz for this rotor. These data were then compared to experimentally acquired data, showing good agreement up to approximately 11 kHz. Above 11 kHz, however, a grid sensitivity study showed dependency of the highest resolvable frequency on the spatial resolution of the computational domain, explaining the roll off in predicted data. Individual broadband noise sources were further investigated by calculating one-third octave sound pressure levels of the unsteady pressure fluctuations acting on the rotor, providing evidence that blade self-noise was the prominent noise source. Using these results, blade wake interaction noise was seen to be negligible for this particular rotor, which was further validated by calculating blade vortex miss distances and comparing to theory.

Christopher S. Thurman↗
NASA NTRS1987

Influence of torsional-lateral coupling on stability behavior of geared rotor systems

In high-performance turbomachinery trouble often arises because of unstable nonsynchronous lateral vibrations. The instabilities are mostly caused by oil-film bearings, clearance excitation, internal damping, annular pressure seals in pumps, or labyrinth seals in turbocompressors. In recent times the coupling between torsional and lateral vibrations has been considered as an additional influence. This coupling is of practical importance in geared rotor systems. The literature describes some field problems in geared drive trains where unstable lateral vibrations occurred together with torsional oscillations. This paper studies the influence of the torsional-lateral coupling on the stability behavior of a simple geared system supported by oil-film bearings. The coupling effect is investigated by parameter studies and a sensitivity analysis for the uncoupled and coupled systems.

Schwibinger, P.↗
NASA NTRS1986

Linear dynamic coupling in geared rotor systems

The effects of high frequency oscillations caused by the gear mesh, on components of a geared system that can be modeled as rigid discs are analyzed using linear dynamic coupling terms. The coupled, nonlinear equations of motion for a disc attached to a rotating shaft are presented. The results of a trial problem analysis show that the inclusion of the linear dynamic coupling terms can produce significant changes in the predicted response of geared rotor systems, and that the produced sideband responses are greater than the unbalanced response. The method is useful in designing gear drives for heavy-lift helicopters, industrial speed reducers, naval propulsion systems, and heavy off-road equipment.

David, J. W.↗
NASA NTRS1972

Dynamic behavior of air lubricated pivoted-pad journal-bearing, rotor system. 2: Pivot consideration and pad mass

Rotor bearing dynamic tests were conducted with tilting-pad journal bearings having three different pad masses and two different pivot geometries. The rotor was vertically mounted and supported by two three-pad tilting-pad gas journal bearings and a simple externally pressurized thrust bearing. The bearing pads were 5.1 cm (2.02 in.) in diameter and 2.8 cm (1.5 in.) long. The length to diameter ratio was 0.75. One pad was mounted on a flexible diaphragm. The bearing supply pressure ranged from 0 to 690 kilonewtons per square meter (0 to 100 psig), and speeds ranged to 38,500 rpm. Heavy mass pad tilting-pad assemblies produced three rotor-bearing resonances above the first two rotor critical speeds. Lower supply pressure eliminated the resonances. The resonances were oriented primarily in the direction normal to the diaphragm.

Nemeth, Z. N.↗
NASA NTRS1980

Evaluation of the effect of elastomeric damping material on the stability of a bearingless main rotor system

The considered investigation was conducted in connection with a contract to design, fabricate, and test a prototype bearingless main rotor (BMR) system. Part of the design process involved an aeroelastic stability investigation in a wind tunnel. Attention is given to a description of model testing, model test results, the description of the full scale wind tunnel configuration, full scale test results, and aspects of correlation with theory. It was found that the complex geometry of the BMR, with 12.5 degrees of nose-up prepitch at the hub and 2.5 degrees of tip-up predroop at the blade attachment clevis, is required to achieve a stable configuration. Subsequent model testing showed that a constrained layer of elastomer material could increase stability at all rotor speeds and collectives tested for a flat strap configuration.

Sheffler, M.↗
NASA NTRS1993

Dynamic modelling and response characteristics of a magnetic bearing rotor system including auxiliary bearings

Auxiliary bearings are a critical feature of any magnetic bearing system. They protect the soft iron core of the magnetic bearing during an overload or failure. An auxiliary bearing typically consists of a rolling element bearing or bushing with a clearance gap between the rotor and the inner race of the support. The dynamics of such systems can be quite complex. It is desired to develop a rotor-dynamic model and assess the dynamic behavior of a magnetic bearing rotor system which includes the effects of auxiliary bearings. Of particular interest is the effects of introducing sideloading into such a system during failure of the magnetic bearing. A model is developed from an experimental test facility and a number of simulation studies are performed. These results are presented and discussed.

Free, April M.↗
NASA NTRS1995

Dynamic modelling and response characteristics of a magnetic bearing rotor system with auxiliary bearings

Auxiliary bearings are a critical feature of any magnetic bearing system. They protect the soft iron core of the magnetic bearing during an overload or failure. An auxiliary bearing typically consists of a rolling element bearing or bushing with a clearance gap between the rotor and the inner race of the support. The dynamics of such systems can be quite complex. It is desired to develop a rotordynamic model which describes the dynamic behavior of a flexible rotor system with magnetic bearings including auxiliary bearings. The model is based upon an experimental test facility. Some simulation studies are presented to illustrate the behavior of the model. In particular, the effects of introducing sideloading from the magnetic bearing when one coil fails is studied.

Free, April M.↗
NASA NTRS1996

Rotordynamic Modelling and Response Characteristics of an Active Magnetic Bearing Rotor System

Auxiliary bearings are a critical feature of any magnetic bearing system. They protect the soft iron core of the magnetic bearing during an overload or failure. An auxiliary bearing typically consists of a rolling element bearing or bushing with a clearance gap between the rotor and the inner race of the support. The dynamics of such systems can be quite complex. It is desired to develop a rotordynamic model which describes the dynamic behavior of a flexible rotor system with magnetic bearings including auxiliary bearings. The model is based upon an experimental test facility. Some simulation studies are presented to illustrate the behavior of the model. In particular, the effects of introducing sideloading from the magnetic bearing when one coil fails is studied. These results are presented and discussed.

Free, April M.↗
NASA NTRS1985

Hover and forward flight acoustics and performance of a small-scale helicopter rotor system

A 2.1-m diam., 1/6-scale model helicopter main rotor was tested in hover in the test section of the NASA Ames 40- by 80- Foot Wind Tunnel. Subsequently, it was tested in forward flight in the Ames 7- by 10-Foot Wind Tunnel. The primary objective of the tests was to obtain performance and noise data on a small-scale rotor at various thrust coefficients, tip Mach numbers, and, in the later case, various advance ratios, for comparisons with similar existing data on full-scale helicopter rotors. This comparison yielded a preliminary evaluation of the scaling of helicopter rotor performance and acoustic radiation in hover and in forward flight. Correlation between model-scale and full-scale performance and acoustics was quite good in hover. In forward flight, however, there were significant differences in both performance and acoustic characteristics. A secondary objective was to contribute to a data base that will permit the estimation of facility effects on acoustic testing.

Kitaplioglu, C.↗
NASA NTRS1979

Experimental investigation of effects of blade tip geometry on loads and performance for an articulated rotor system

Wind-tunnel tests of an aeroelastically designed helicopter rotor model were carried out to determine the effects on dynamic response and aerodynamic performance of varying the design of the outboard 8 percent of the blade lengths. Four different blade tip geometries or shapes having different amounts of planform sweep, thickness and chordwise taper, and anhedral angle were studied. Each configuration was tested at several shaft angles of attack for advance ratios of 0.20, 0.30, 0.35, and 0.40. For each combination of shaft angle and advance ratio, rotor lift was varied over a wide range to include high lift conditions.

Weller, W. H.↗