Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROLLER BEARING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Evaluation of ball and roller bearings restored by grinding

A joint program was undertaken to restore by grinding those rolling-element bearings which are currently being discarded at aircraft engine and transmission overhaul. Three bearing types were selected from the UH-1 helicopter engine (T-53) and transmission for the pilot program. Groups of each of these bearings were visually and dimensionally inspected for suitability for restoration. A total of 250 bearings were restored by grinding. Of this number, 30 bearings from each type were endurance tested to a TBO of 1600 hours. No bearing failures occurred related to the restoration by grinding process. The two bearing failures which occurred were due to defective rolling elements and were typical of those which may occur in new bearings. The restorable component yield to the three groups was in excess of 90 percent.

Parker, R. J.↗
NASA NTRS1984

Thermal analysis of a planetary transmission with spherical roller bearings operating after complete loss of oil

Planetsys and Spherbean, two computer programs developed for the analysis of rolling element bearings, were used to simulate the thermal performance of an OH-58 helicopter main rotor transmission. A steady state and a transient thermal analysis were made and temperatures thus calculated were compared with experimental data obtained from a transmission that was operated to destruction, which occurred about 30 min after all the oil was drained from the transmission. Temperatures predicted by Spherbean were within 3% of the corresponding measured values at 15 min elapsed time and within 9% at 25 min. Spherbean also indicates a potential for high bearing cage temperatures with misalignment and outer ring rotation.

Coe, H. H.↗
NASA NTRS1990

A study of fracture mechanisms in ATD roller bearing

The purpose was to investigate how microstructures, especially anisotropy, affects internal stresses and the overall mechanical response of bearings. Samples with the stress axis along the aligned carbide direction possessed high modulus values compared to those with their axis perpendicular to the carbide stringers. The difference in the modulus was found to be more than a factor of two. A series of experiments was conducted on rolled samples to further investigate this effect; the two sets of results were consistent with each other. The degree of anisotropy of the microstructure in terms of the carbide and matrix orientations was determined using x-ray diffraction. The stress state determination was conducted using neutron diffraction. It was found that there was little variation in the distribution of the internal stresses amongst different samples, indicating that small changes in the processing and geometrical conditions did not result in significant variations in the internal stress. A nominal tensile hoop stress of 39 ksi was obtained for the inner raceway. Furthermore, during the course of the investigation, it was apparent that there was a need to determine the stress state induced by the shrink fitting process. Therefore, a series of experiments was conducted using strain gages to identify the stress distribution in a shrink fitting process in three different types of geometries. Correlations were obtained to estimate the highest stress values in the outer and inner groove geometry. A finite element program based on the ANSYS system was developed to compute the stress distribution in the inner raceway geometry. This analysis indicates that the highest tensile stress in the system occurs at the ID of the ring with a stress value of over 5 times that of the applied radial stress. Results from all these facets were correlated with one another. It appears that the material does not fail as a result of any one single factor, but results from a combination of the various factors investigated.

Zee, Ralph H.↗
NASA NTRS1992

Hybrid Hydrostatic/Transient Roller Bearing Assembly

Proposed bearing assembly for shaft of high-speed turbopump includes both hydrostatic and rolling-element bearings. Rolling-element bearing unloaded at high speed by centrifugal expansion of outer race and transient retainer.

Justak, John F.↗
NASA NTRS1940

Experiments on Ball and Roller Bearings Under Conditions of High Speed and Small Oil Supply

This report describes a testing machine on which 35 millimeter bearings (bore) can be run at speeds of the order of 21,000 rpm, while the following factors are recorded: 1) oil circulation through bearing and oil temperature. 2) maximum temperature of outer bearing ring, 3) radial and axial load on bearing, 4) radial, axial, and angular clearance of bearing, 5) power consumption of bearing. The experiments show that the lubrication was most reliable and oil consumption lowest when the oil was introduced through a hole in the outer or inner ring of the bearing.

Getzlaff, Gunter↗
NASA NTRS2007

Model Specification for Rework of Aircraft Engine, Power Transmission, and Accessory/Auxiliary Ball and Roller Bearings

This document provides a model specification for the rework and/or repair of bearings used in aircraft engines, helicopter main power train transmissions, and auxiliary bearings determined to be critical by virtue of performance, function, or availability. The rolling-element bearings to be processed under the provisions of this model specification may be used bearings removed after service, unused bearings returned from the field, or certain rejected bearings returned for reinspection and salvage. In commercial and military aircraft application, it has been a practice that rolling-element bearings removed at maintenance or overhaul be reworked and returned to service. Depending on the extent of rework and based upon theoretical analysis, representative life factors (LF) for bearings subject to rework ranged from 0.87 to 0.99 the lives of new bearings. Based on bearing endurance data, 92 percent of the bearing sets that would be subject to rework would result in L(sub 10) lives equaling and/or exceeding that predicted for new bearings. The remaining 8 percent of the bearings have the potential to achieve the analytically predicted life of new bearings when one of the rings is replaced at rework. The potential savings from bearing rework varies from 53 to 82 percent of that of new bearings depending on the cost, size, and complexity of the bearing

Zaretsky, Erwin V.↗
NASA NTRS1996

Bearings Incorporating Deadband Rollers

Bearings in high-pressure turbopump redesigned to incorporate rollers allowing limited axial motion within small deadband. Does not permit radial deadband motion. Axial deadband motion used for rotor-thrust-balance control. Design eliminates some nonlinearities in dynamics of pump rotor and assists in suppressing vibrations at harmonics of frequency of rotation.

Gualtieri, Guy V.↗
NASA NTRS1988

Mechanical pumps for superfluid helium transfer in space

Two alternate mechanical pump concepts have been identified for the transfer of superfluid helium in space. Both pumps provide flow at sufficient head and have operating characteristics suitable for the Space Infrared Telescope Facility (SIRTF) refill mission. One pump operates at a relatively low speed and utilizes mechanical roller bearings, while the other operates at a higher rotational speed using either electromagnetic or tilting pad gas-dynamic bearings. The use of gas bearings requires transfer of normal helium so that the gas pressure within the pump casing is high enough to operate the bearings. The operating characteristics of both pumps are predicted, the dimensions are estimated and major technology issues are identified. The major issues for each pump design are cavitation performance and bearing development. Roller bearings require quantified reliability for operation in space while electromagnetic bearings require basic development as well as a complex control system. The low speed pump has significantly poorer hydraulic efficiency than the high speed pump.

Izenson, M. G.↗
NASA NTRS1964

High temperature bearings.

Lubrication techniques and roller bearing materials for operations in high temperature environment

LUBRICATION↗
NASA NTRS2016

Rolling Bearing Life Prediction, Theory, and Application

A tutorial is presented outlining the evolution, theory, and application of rolling-element bearing life prediction from that of A. Palmgren, 1924; W. Weibull, 1939; G. Lundberg and A. Palmgren, 1947 and 1952; E. Ioannides and T. Harris, 1985; and E. Zaretsky, 1987. Comparisons are made between these life models. The Ioannides-Harris model without a fatigue limit is identical to the Lundberg-Palmgren model. The Weibull model is similar to that of Zaretsky if the exponents are chosen to be identical. Both the load-life and Hertz stress-life relations of Weibull, Lundberg and Palmgren, and Ioannides and Harris reflect a strong dependence on the Weibull slope. The Zaretsky model decouples the dependence of the critical shear stress-life relation from the Weibull slope. This results in a nominal variation of the Hertz stress-life exponent. For 9th- and 8th-power Hertz stress-life exponents for ball and roller bearings, respectively, the Lundberg-Palmgren model best predicts life. However, for 12th- and 10th-power relations reflected by modern bearing steels, the Zaretsky model based on the Weibull equation is superior. Under the range of stresses examined, the use of a fatigue limit would suggest that (for most operating conditions under which a rolling-element bearing will operate) the bearing will not fail from classical rolling-element fatigue. Realistically, this is not the case. The use of a fatigue limit will significantly overpredict life over a range of normal operating Hertz stresses. (The use of ISO 281:2007 with a fatigue limit in these calculations would result in a bearing life approaching infinity.) Since the predicted lives of rolling-element bearings are high, the problem can become one of undersizing a bearing for a particular application. Rules had been developed to distinguish and compare predicted lives with those actually obtained. Based upon field and test results of 51 ball and roller bearing sets, 98 percent of these bearing sets had acceptable life results using the Lundberg- Palmgren equations with life adjustment factors to predict bearing life. That is, they had lives equal to or greater than that predicted. The Lundberg-Palmgren model was used to predict the life of a commercial turboprop gearbox. The life prediction was compared with the field lives of 64 gearboxes. From these results, the roller bearing lives exhibited a load-life exponent of 5.2, which correlated with the Zaretsky model. The use of the ANSI/ABMA and ISO standards load-life exponent of 10/3 to predict roller bearing life is not reflective of modern roller bearings and will underpredict bearing lives.

Life prediction↗
NASA NTRS2005

Software Developed for Analyzing High- Speed Rolling-Element Bearings

COBRA-AHS (Computer Optimized Ball & Roller Bearing Analysis--Advanced High Speed, J.V. Poplawski & Associates, Bethlehem, PA) is used for the design and analysis of rolling element bearings operating at high speeds under complex mechanical and thermal loading. The code estimates bearing fatigue life by calculating three-dimensional subsurface stress fields developed within the bearing raceways. It provides a state-of-the-art interactive design environment for bearing engineers within a single easy-to-use design-analysis package. The code analyzes flexible or rigid shaft systems containing up to five bearings acted upon by radial, thrust, and moment loads in 5 degrees of freedom. Bearing types include high-speed ball, cylindrical roller, and tapered roller bearings. COBRA-AHS is the first major upgrade in 30 years of such commercially available bearing software. The upgrade was developed under a Small Business Innovation Research contract from the NASA Glenn Research Center, and incorporates the results of 30 years of NASA and industry bearing research and technology.

Fleming, David P.↗