SEARCH · Engineering Papers

Results for “RF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Efficient 30-W, 140-MHz rf amplifier for CW CO2 waveguide laser excitation

Details of a 30-W, 140-MHz rf amplifier for CW CO2 waveguide laser excitation are presented. The amplifier delivers 30 W into a 50-Ohm load while requiring only 40 W of dc power from a 28-V supply and 100 mW of rf drive power for an overall efficiency of 75 percent. A coupling-starting network design theory is given that provides the initiation over voltage for the discharge plasma from an rf power source of limited output voltage capability. The network then matches the drive circuit to the new input impedance of the operating discharge without any adjustments. This design theory applies to the whole class of networks whose losses can be approximated by a loss conductance in parallel with the gas discharge.

Hochuli, U. E.↗

NASA NTRS1992

RF modulated fiber optic sensing systems and their applications

A fiber optic sensing system with an intensity sensor and a Radio Frequency (RF) modulated source was shown to have sensitivity and resolution much higher than a comparable system employing low modulating frequencies or DC mode of operation. Also the RF modulation with an appropriate configuration of the sensing system provides compensation for the unwanted intensity losses. The basic principles and applications of a fiber optic sensing system employing an RF modulated source are described. In addition the paper discusses various configurations of the system itself, its components, and modulation and detection schemes. Experimental data are also presented.

Adamovsky, Grigory↗

NASA NTRS1993

RF modulated fiber optic sensing systems and their applications

Adamovsky, G.↗

NASA NTRS1995

Silicon Micromachining in RF and Photonic Applications

Texas Instruments (TI) has developed membrane and micromirror devices since the late 1970s. An eggcrate space membrane was used as the spatial light modulator in the early years. Discrete micromirrors supported by cantilever beams created a new era for micromirror devices. Torsional micromirror and flexure-beam micromirror devices were promising for mass production because of their stable supports. TI's digital torsional micromirror device is an amplitude modulator (known as the digital micromirror device (DMD) and is in production development, discussed elsewhere. We also use a torsional device for a 4 x 4 fiber-optic crossbar switch in a 2 cm x 2 cm package. The flexure-beam micromirror device is an analog phase modulator and is considered more efficient than amplitude modulators for use in optical processing systems. TI also developed millimeter-sized membranes for integrated optical switches for telecommunication and network applications. Using a member in radio frequency (RF) switch applications is a rapidly growing area because of the micromechanical device performance in microsecond-switching characteristics. Our preliminary membrane RF switch test structure results indicate promising speed and RF switching performance. TI collaborated with MIT for modeling of metal-based micromachining.

Lin, Tsen-Hwang↗

NASA NTRS2003

Beam-Switch Transient Effects in the RF Path of the ICAPA Receive Phased Array Antenna

When the beam of a Phased Array Antenna (PAA) is switched from one pointing direction to another, transient effects in the RF path of the antenna are observed. Testing described in the report has revealed implementation-specific transient effects in the RF channel that are associated with digital clocking pulses that occur with transfer of data from the Beam Steering Controller (BSC) to the digital electronics of the PAA under test. The testing described here provides an initial assessment of the beam-switch phenomena by digitally acquiring time series of the RF communications channel, under CW excitation, during the period of time that the beam switch transient occurs. Effects are analyzed using time-frequency distributions and instantaneous frequency estimation techniques. The results of tests conducted with CW excitation supports further Bit-Error-Rate (BER) testing of the PAA communication channel.

Sands, O. Scott↗

NASA NTRS2003

Packaging Considerations for Integrated RF Microphotonic Receiver at Ka-Band

The NASA Computing, Information and Communications Technology (CICT) Program is supporting the development of an RF microphotonic Ka-band receiver. The receiver consists of a lithium niobate micro-disk that enables the incoming RF signal (up to Ka-band) to be coupled to the optical signal (approx. 200 THz). The modulated optical signal is detected by the high-speed photonic signal processing electronics. When compared with an all-electronic approach, the microphotonic receiver technology offers 1 Ox smaller volume, smaller weight, and smaller power consumption, greater sensitivity, and optical isolation for applications in extreme environments. It could potentially be implemented to support planetary surface-to-surface and surface-to-relay communications, as well as high-data-rate inter-satellite links. We are currently studying a number of fabrication and integration issues that could result as this technology is advanced for potential insertion into a NASA mission. The results of our preliminary effort to integrate the RF microphotonic receiver components (e.g., the lithium niobate micro-disk, the optical elements, and the Ka-band patch antenna) on an etched silicon wafer will be presented, In addition, the concomitant integration and packaging issues, and the potential NASA applications will be discussed.

Nguyen, Hung↗

NASA NTRS2000

Radio Frequency (RF) Micro-Electromechanical Systems (MEMS) Switches for Space Communications

Micro-electromechanical systems (MEMS) is an emerging technology for radio frequency (RF) systems because it has the potential to dramatically decrease loss and improve efficiency. In this paper, we address the design and fabrication of novel MEMS switches being developed at NASA Glenn Research Center. Two types of switches are being developed: a microstrip series single pole single throw (SPST) switch and a coplanar waveguide (CPW) series SPST and single pole double throw (SPDT) switches. These are being fabricated as an integral part of 50 Ohm microstrip and CPW RF integrated circuits using microfabrication techniques. The construction of the switch relies on a cantilever beam that is partially supported by a dielectric post. The cantilever beam is electro-magnetically actuated. To decrease stiction, a Si3N4 thin film is deposited over the contact area. Thus, when the switch is closed, the ON-state insertion loss is governed by the parallel plate capacitance formed by the two contacts. The isolation in the OFF-state is governed by the parasitic capacitance when the cantilever is in the up position. RF MEMS switches have been demonstrated with 80% lower insertion loss than conventional solid state devices (GaAs Metal Semiconductor Field Effect Transistors (MESFETs) and Silicon PIN diodes) based switches. For example, a conventional GaAs five-bit phase shifter which is required for beam steering in a phased array antenna has approximately 7 dB of insertion loss at 26.5 GHz where as a comparable MEMS based phase shifter is expected to have only 2 dB of insertion loss. This translates into 56% lower power dissipation and therefore decreases the thermal load on the spacecraft and also reduces the power amplifier requirements. These benefits will enable NASA to build the next generation of deep space science crafts and micro/nano satellites.

Simons, Rainee N.↗

NASA NTRS2008

MISSE Results Used for RF Plasma Ground Testing-To-Space-Exposure Correlation for Coated Kapton

The ability to predict the durability of materials in the low Earth orbit (LEO) environment by exposing them in ground-based facilities is important because one can achieve test results sooner, expose more types of materials, and do it much more cost effectively than to test them in flight. However, flight experiments to determine the durability of groups or classes of materials that behave similarly are needed in order to provide correlations of how much time in ground-based facilities represents certain durations in LEO for the material type of interest. An experiment was designed and flown on the Materials International Space Station Experiment (MISSE) 2 (3.95 yr in LEO) and MISSE 4 (1.04 yr in LEO) in order to develop this type of correlation between ground-based RF plasma exposure and LEO exposure for coated Kapton. The experiment consisted of a sample of Kapton H (DuPont) polyimide coated with 1300 of silicon dioxide by Sheldahl, Inc. The samples were exposed to atomic oxygen in a radio frequency (RF) generated atomic oxygen plasma. Mass change was measured for the samples and then the same samples were exposed in flight on MISSE and the mass change was again recorded post-flight. After documentation, the samples were exposed again in the ground-based RF plasma in order to determine if the erosion would be the same as it had been in the same facility pre-flight which would indicate whether or not the sample had been damaged during flight and if the defects on the surface were those that were there preflight. The slopes of the mass change versus fluence plots were then used to develop a correlation factor that can be used to help predict the durability of coated Kapton in ground-based isotropic atomic oxygen plasma systems. This paper describes the experiment and presents the correlation factor results.

Miller, Sharon K. R.↗

NASA NTRS2013

RF Reference Switch for Spaceflight Radiometer Calibration

The goal of this technology is to provide improved calibration and measurement sensitivity to the Soil Moisture Active Passive Mission (SMAP) radiometer. While RF switches have been used in the past to calibrate microwave radiometers, the switch used on SMAP employs several techniques uniquely tailored to the instrument requirements and passive remote-sensing in general to improve radiometer performance. Measurement error and sensitivity are improved by employing techniques to reduce thermal gradients within the device, reduce insertion loss during antenna observations, increase insertion loss temporal stability, and increase rejection of radar and RFI (radio-frequency interference) signals during calibration. The two legs of the single-pole double-throw reference switch employ three PIN diodes per leg in a parallel-shunt configuration to minimize insertion loss and increase stability while exceeding rejection requirements at 1,413 MHz. The high-speed packaged diodes are selected to minimize junction capacitance and resistance while ensuring the parallel devices have very similar I-V curves. Switch rejection is improved by adding high-impedance quarter-wave tapers before and after the diodes, along with replacing the ground via of one diode per leg with an open circuit stub. Errors due to thermal gradients in the switch are reduced by embedding the 50-ohm reference load within the switch, along with using a 0.25-in. (approximately equal to 0.6-cm) aluminum prebacked substrate. Previous spaceflight microwave radiometers did not embed the reference load and thermocouple directly within the calibration switch. In doing so, the SMAP switch reduces error caused by thermal gradients between the load and switch. Thermal issues are further reduced by moving the custom, highspeed regulated driver circuit to a physically separate PWB (printed wiring board). Regarding RF performance, previous spaceflight reference switches have not employed high-impedance tapers to improve rejection. The use of open-circuit stubs instead of a via to provide an improved RF short is unique to this design. The stubs are easily tunable to provide high rejection at specific frequencies while maintaining very low insertion loss in-band.

Knuble, Joseph↗

NASA NTRS2014

An RF Sensor for Gauging Screen-Channel Liquid Acquisition Devices for Cryogenic Propellants

A key requirement of a low-gravity screen-channel liquid acquisition device (LAD) is the need to retain 100% liquid in the channel in response to propellant outflow and spacecraft maneuvers. The point at which a screen-channel LAD ingests vapor is known as breakdown, and can be measured several different ways such as: visual observation of bubbles in the LAD channel outflow; a sudden change in pressure drop between the propellant tank and LAD sump outlet; or, an indication by wet-dry sensors placed in the LAD channel or outflow stream. Here we describe a new type of sensor for gauging a screen-channel LAD, the Radio Frequency Mass Gauge (RFMG). The RFMG measures the natural electromagnetic modes of the screen-channel LAD, which is very similar to an RF waveguide, to determine the amount of propellant in the channel. By monitoring several of the RF modes, we show that the RFMG acts as a global sensor of the LAD channel propellant fill level, and enables detection of LAD breakdown even in the absence of outflow. This paper presents the theory behind the RFMG-LAD sensor, measurements and simulations of the RF modes of a LAD channel, and RFMG detection of LAD breakdown in a channel using a simulant fluid during inverted outflow and long-term stability tests.

microwave sensor↗

NASA NTRS2014

The Miniature Radio Frequency Instruments (Mini-RF) Global Observations of Earth's Moon

Radar provides a unique means to analyze the surface and subsurface physical properties of geologic deposits, including their wavelength-scale roughness, the relative depth of the deposits, and some limited compositional information. The NASA Lunar Reconnaissance Orbiter's (LRO) Miniature Radio Frequency (Mini-RF) instrument has enabled these analyses on the Moon at a global scale. Mini-RF has accumulated 67% coverage of the lunar surface in S-band (12.6 cm) radar with a resolution of 30 m/pixel. Here we present new Mini-RF global orthorectified uncontrolled S-band maps of the Moon and use them for analysis of lunar surface physical properties. Reported here are readily apparent global- and regional-scale differences in lunar surface physical properties that suggest three distinct terranes, namely: a (1) Nearside Radar Dark Region; (2) Orientale basin and continuous ejecta; and the (3) Highlands Radar Bright Region. Integrating these observations with new data from LRO's Diviner Radiometer rock abundance maps, as well Clementine and Lunar Prospector derived compositional values show multiple distinct lunar surface terranes and sub-terranes based upon both physical and compositional surface properties. Previous geochemical investigations of the Moon suggested its crust is best divided into three to four basic crustal provinces or terranes (Feldspathic Highlands Terrane (-An and -Outer), Procellarum KREEP Terrane, and South Pole Aitken Terrane) that are distinct from one another. However, integration of these geochemical data sets with new geophysical data sets allows us to refine these terranes. The result shows a more complex view of these same crustal provinces and provides valuable scientific and hazard perspectives for future targeted human and robotic exploration.

Radar observations↗

NASA NTRS2018

Lunar Relay Coverage Analysis for RF and Optical Links

This paper describes our effort in searching different lunar relay architectures and assessing their coverage performance and other pros and cons for RF and optical links. Regarding RF links, we considered three notional lunar relay architectures, all communicating with the three sites of the Deep Space Network (DSN): Goldstone, California; Canberra, Australia; and Madrid, Spain: 1) A constellation of three relay orbiters: two at the Polar frozen elliptical orbits, and one at an equatorial circular orbit. 2) One relay orbiter in a 74-day Lissajous orbit at Earth-Moon Lagrange Point L2. 3) One relay orbiter in a 14-day Lunar distance retrograde orbit. Regarding optical link, we considered a notional multi-hop relay architecture that consists of one relay orbiter in a 74-day Lissajous orbit at Earth-Moon L2 (as in architecture #2 in the RF case), three Near-Earth relay satellites in geosynchronous orbit at longitudes 187° E, 110° E, and 347° E, and three ground stations at White Sands (US), Guam (US), and Tenerife (Spain). We introduce the additional constraints of Sun-“Earth”Probe (SEP) angle for return links, and Sun-Probe-“Earth” (SPE) angle for forward links. SPE and SPE angles determine the amount of sunlight (noise) that goes into the detector of the telescope, thus affecting the capacity of an optical link.

Lee, Charles↗

NASA NTRS2020

CubeSat Array for Detection of RF Emissions from Exoplanets using Inter-Satellite Optical Communicators

We are presenting a CubeSat mission concept wherein a large number of small spacecraft furnished with Ultra-Long Wavelength (ULW) observation antennas is to be implemented to synthesize a large aperture for detecting ULW emissions from selected exoplanets. The CubeSat Array for the Detection of RF Emissions from Exoplanets (CADRE) concept involves the placement of a swarm arrangement of CubeSats into small amplitude Lissajous orbits around the Earth-Moon L2 point. In addition to the ULW receivers, each CADRE CubeSat will be furnished with a novel omnidirectional optical communicator which should allow data sharing at gigabit per second data rates. In this paper we discuss the science goals, potential architecture and key technical challenges of an eventual CADRE implementation. We present the estimated interferometer specifications needed to detect Exoplanet RF emissions, CubeSat orbits and formations as well as CubeSat design considerations. Special focus is placed on the design of the mission-enabling inter-CubeSat optical cross link which allows for fast sharing of the detected RF signals for subsequent correlation.

Bentum, Mark↗

NASA NTRSDate not supplied

Design and Analysis of Convolutional Neural Network for RF Signal Modulation Classification for In-Orbit Deployment

To effectively transmit data to and from satellites requires a complex and robust RF communication system. Commonly, several different types of signal modulations may be required to maximize satellite efficiency depending on a variety of unexpected channel impairments. We propose a neural network algorithm capable of learning these RF signal modulations using a supervised learning technique designed for low power, high-efficiency in-orbit deployment. The work presented demonstrates a convolutional neural network (CNN) capable of learning and recognizing a set of modulation schemes commonly used to transmit RF information. We are capable of recognizing the modulation scheme from the I and Q data channels directly, with no preprocessing or data conversion required other than breaking the incoming signal into a set of uniform normalized samples. We perform a network design and size analysis, showing that reasonably high accuracy can be obtained using networks with a relatively low number of trainable parameters. Given that a user of a system such as this may wish to receive a signal using a modulation scheme that the network has not previously learned, we demonstrate that transfer learning can learn new modulation schemes by retraining only the fully connected layers in the CNN. Thus, this type of network would excel in outer space deployment using high-efficiency transfer learning hardware. Modulation recognition can be performed through rapid feedforward computation, and the CNN training process is significantly simplified when learning new modulations is required.

CNN↗

NASA NTRS1997

An All-Optical Microwave Mixer with 8db RF Gain

An all-optical microwave mixer with an 8dB RF gain is demonstrated by using a semiconductor optical amplifier (SOA). 6GHz RF signal on a 1312 nm optical carrier is up-converted and down-converted to 1GHZ and 11 GHz by a 5GHz local oscillation (LO) signal on a 1320 nm optical carrier. Such a carrier could readily extend to millimeter wave range.

microwave mixer fiberoptics fiber optic transmissi↗

NASA NTRS1993

Performance of RF Downlink with Periodic Data Frame

Telemetry discrete spectrum components induced by the periodicity of an Attached Sync Marker may coincide with the RF carrier frequency causing unwanted interference while tracking the RF carrier.

pseudo randomizer decrease potential interference ↗

NASA NTRS2013

Evidence for Water Ice on the Moon: Results for Anomalous Polar Craters from the LRO Mini-RF Imaging Radar

The Mini-RF radar instrument on the Lunar Reconnaissance Orbiter spacecraft mapped both lunar poles in two different RF wavelengths (complete mapping at 12.6 cm S-band and partial mapping at 4.2 cm X-band) in two look directions, removing much of the ambiguity of previous Earth- and spacecraft-based radar mapping of the Moon's polar regions. The poles are typical highland terrain, showing expected values of radar cross section (albedo) and circular polarization ratio (CPR). Most fresh craters display high values of CPR in and outside the crater rim; the pattern of these CPR distributions is consistent with high levels of wavelength-scale surface roughness associated with the presence of block fields, impact melt flows, and fallback breccia. A different class of polar crater exhibits high CPR only in their interiors, interiors that are both permanently dark and very cold (less than 100 K). Application of scattering models developed previously suggests that these anomalously high-CPR deposits exhibit behavior consistent with the presence of water ice. If this interpretation is correct, then both poles may contain several hundred million tons of water in the form of relatively "clean" ice, all within the upper couple of meters of the lunar surface. The existence of significant water ice deposits enables both long-term human habitation of the Moon and the creation of a permanent cislunar space transportation system based upon the harvest and use of lunar propellant.

Mini-RF radar↗

NASA NTRS1967

Feed-through connector couples RF power into vacuum chamber

Feed-through device connects RF power to an RF coil in a vacuum chamber. The coil and leads are water cooled and vacuum tight seals are provided at the junctions. The device incorporates silver soldered copper tubes, polytetrafluoroethylene electrical insulators, and O-ring vacuum seals.

Grandy, G. L.↗