Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Purification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Van de Graaff Irradiation Studies of Oxygen Sensor and Hydrated Zirconia Sorbent

Commercial-scale production of Mo-99 demands a facility-wide assessment of radiation-induced degradation across process equipment, instrumentation, and purification media. Key factors— total ionizing dose, dose rate, radiolysis-driven chemistry, thermal loads, activation, and any neutron-related effects—should inform material selection, shielding, and component layout. Purification materials (sorbents, resins, filters, seals, housing) require particular attention to ensure that irradiation does not alter selectivity or capacity, generate fines, or introduce leachables that could compromise Mo-99 purity or downstream Tc-99m generator performance. Dose mapping, accelerated irradiation testing, and studies of extractables/leachables together provide the basis for setting maintenance, calibration, and replacement intervals and for qualifying materials that retain mechanical integrity, chemical compatibility, and radiopurity over their service life.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microbial Biomining for the Release and Recovery of Rare Earth Elements in Abandoned Coal Mine Drainage

Microbes can be used for biomining rare earth elements (REEs) from abandoned coal-mine drainage (AMD) solids. Domestically Pennsylvania has ~11,000 abandoned mines, with ~500 AMD passive remediation systems (PRSs) that precipitate REE rich solids. In passive systems, REEs, co-precipitate with manganese (Mn), accumulating as a valuable leachate when resolubilized. REEs like lanthanum (La) are used in battery technology. Microbial metabolism that co-resolubilize Mn and REEs could result in an affordable release process that does not require the addition of hazardous chemical additives. Microbial sequestering of La can be used for selective purification from a mixed REE composition. Currently, the microbial mechanisms that contribute to mass REE resolubilization and selective sequestration are poorly understood. We have isolated bacteria (Bacillus mycoides JR07 and Bacillus pseudomycoides KB7) that solubilize Mn oxide, La oxide, and AMD solids by acidogenesis. Preliminary results show methylotrophic bacterial isolate B3 can take up soluble La, which may have a potential application in the purification of La from a mixed REE leachate. Determining the microbial metabolism and genes involved in the REE resolubilization and selective biomining of La is crucial to optimize the biomining of AMD solids. Our work addresses the growing need to develop novel REE recovery methods from domestic sources.

microbiology↗
DOE OSTI2026

Progress Towards Synthesis of Uranium Chloride Fuel Salts Using Zinc Chloride

Reliable, scalable methods for producing high-purity actinide chloride salts are needed to support molten salt reactor fuel development and deployment. This report describes the continued development and demonstration of a bench-scale chlorination and purification apparatus using a zinc chloride-based method for synthesizing uranium chloride fuel salts. In this approach, uranium metal is chlorinated by ZnCl2 to produce LiCl-KCl-UCl3. Reaction with three aliquots of added uranium metal was used to generate a target uranium concentration of 30 wt %. While this concentration was chosen for initial testing of the apparatus and method, the final uranium concentration is not limited to 30 wt %. The zinc metal generated in the reaction forms an immiscible layer that was removed by volatilization at moderately high temperatures. Electrochemical measurements confirmed the removal of zinc and applied sensing methods indicated the uranium concentration to be approximately 25 wt %. These initial results demonstrate that the bench-scale chlorination apparatus is an effective platform for the synthesis and purification of uranium chloride salts using ZnCl2. This method shows promise for application to industry-relevant salt systems such as NaCl-UCl3. Further development is recommended to optimize reagent loading, zinc removal, and avoid possible U-Zn alloy formation.

Dulovic, Stephanie↗
DOE OSTI2026

Universal monitored dynamics in multimode bosonic systems

We propose a route to study monitored many-body dynamics in multimode bosonic systems using circuit quantum electrodynamics. In this experimental setting, we construct several bosonic models comprising brickwork circuits built from beam-splitter gates, local parity measurements, and optional on-site Hubbard interactions, and diagnose their monitored dynamics via ancilla purification and a learnability-based probe. Under parity measurements, generic gate sets exhibit behavior that is largely consistent with a conventional measurement-induced phase transition, while a special class of beam-splitter circuits shows an apparent critical-like high-measurement regime in which purification times scale linearly with system size. We show that for realistic noise, gate, and measurement rates, these signatures are observable with near-term circuit QED hardware.

Patel, Shivam [Rutgers U., Piscataway]↗
DOE OSTI2024

Challenges, progress, and future perspectives for cyanobacterial polyhydroxyalkanoate production

Polyhydroxyalkanoates (PHA) are a promising bio-based alternative to traditional plastics derived from petroleum. Cyanobacteria are photosynthetic organisms that produce PHA from CO 2 and sunlight, which can potentially reduce production costs and environmental footprint in comparison to heterotrophic bacteria cultures because (1) they utilize inorganic carbon sources for growth and (2) they do not require intensive aeration for oxygenation. Moreover, supplementing precursors such as propionate, acetate, valerate, etc., can be used to obtain various copolymers with plastic customizable properties in comparison to the classical homopolymers, such as polyhydroxybutyrate, PHB. This critical review covers the latest advances in PHA production, including recent discoveries in the metabolism interplay between PHA and glycogen production, and new insights into cultivation strategies that enhance PHA accumulation, and purification processes. This review also addresses the challenges and suggests potential solutions for a viable industrial PHAs production process.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

147 Nd Quantification Using HSCCC-Purified Samples

Quantifying the fission product 147 Nd in nuclear debris samples is an important component of post-detonation nuclear forensics. The most accurate quantifications are obtained when Nd is purified from all other fission products, actinides, activation products, and environmental matrix contained within the debris. In this study, a recently developed method for Nd purification was tested, purifying 147 Nd from solutions of mixed fission products using high-speed counter-current chromatography (HSCCC). Importantly, the new method allowed for faster elution of Nd from the column as compared with established high performance liquid chromatography (HPLC) methods, and resulted in accurate/precise 147 Nd quantification by gamma-ray spectrometry. While the up-front equipment costs associated with HSCCC may be higher, its operational costs are on par with those of HPLC (solvents, extractants, power). Gas-flow proportional beta decay counting revealed contamination from the nearest neighbor lanthanide 143 Pr (a gamma-silent radioisotope) in the HSCCC-purified samples, but the activity contribution from 147 Nd could still be quantified. Remarkably consistent elution profiles were observed for the HSCCC method, spanning rare earth element (REE) loadings of more than 10 orders of magnitude (tracer to mmol quantities). In conclusion, the reliability and speed of the new method suggest utility for the rapid separation and quantification of 147 Nd in unknown samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Growth of High-Purity CsPbBr 3 Crystals for Enhanced Gamma-Ray Detection

High-quality CsPbBr 3 crystals hold significant potential for gamma-ray detection due to their remarkable optoelectronic properties. This study details an optimized production process using the Bridgman method to achieve highly pure CsPbBr 3 crystals. By implementing rigorous synthesis and purification techniques, we successfully reduced the total impurity levels to 9 ppm, as confirmed by glow discharge mass spectroscopy (GDMS). The resulting CsPbBr 3 crystals demonstrate exceptional performance, including high transparency, intense photoemission, and prolonged photoluminescence decay times. These properties facilitate superior gamma-ray detection with an energy resolution of 1.4% for the 137 Cs 662 keV gamma-rays, comparable to commercial Cd 1-x Zn x Te (CZT) detectors. Our findings underscore the critical relationship between material purity and detector performance, highlighting the potential of CsPbBr 3 as a cost-effective alternative in radiation detection applications. Further studies on defect origins and electronic states are necessary to fully leverage the capabilities of CsPbBr 3 crystals in practical high-energy radiation detection systems.

Bridgman↗
DOE OSTI2025

Catalytic Oxygen Reduction for Deep O 2 Removal from CO 2 Streams

Streams of CO 2 from various capture processes may contain several impurities of which O 2 is often overlooked as a problematic impurity. Because of its reactivity, the National Energy Technology Laboratory has recommended a stringent limit, less than 10 ppm, for the O 2 level in treated CO 2 products for safe transport, storage, and utilization. Here, in this study, a variety of catalytic oxygen reduction approaches using commercial automotive exhaust emission catalysts are evaluated for O 2 removal from CO 2 streams using different reducing agents, including H 2 , CO, CH 3 OH, and CH 4 . When the amount of reductant added into the feed is carefully controlled, H 2 , CO, or CH 3 OH can effectively remove O 2 from 1.5% to below 10 ppm with a single-reactor design (>99.93% removal efficiency), while simultaneously meeting the impurity limits for other species. With CH 4 as a reductant, it is challenging to simultaneously meet the the O 2 and CO specifications in a single-reactor design because CH 4 also reacts with CO 2 to produce high levels of CO in the stream (at several hundred ppm). A dual-reactor design is developed to enable the use of CH 4 , a readily available and low-cost reductant, for the purification of CO 2 streams to meet the specifications for O 2 and other impurities.

CO2 purification↗
DOE OSTI2026

Water as a gas separation membrane

Efficient gas separation membranes are essential for carbon capture, biogas upgrading, and hydrogen purification. Inspired by how plants absorb CO 2 through water, we present a membrane platform that uses liquid water as the selective layer. Hydrophilic sub-100-nm pores stabilize water through strong capillary forces, enabling operation at feed pressures above 72 bar under dry and humid conditions. Selectivity is governed by gas solubility in water, while permeance is tuned by adjusting the water layer thickness. Reducing this thickness below 200 nm yields CO 2 permeances up to 11,600 gas permeation units with CO 2 :N 2 , CO 2 :CH 4 , and CO 2 :H 2 selectivities of 40, 26, and 31, respectively, surpassing the performance of state-of-the-art membranes. Operation is sustained for over a week without water loss, and performance scales using commercially available porous polymer supports under mixed-gas crossflow conditions. Water’s dissolution-based transport avoids saturation and reaction-rate limits, enabling a robust, high-performance, and environmentally benign gas separation platform.

08 HYDROGEN↗
DOE OSTI2025

Transformational Sorbent-Based Process for a Substantial Reduction in the Cost of CO2 Capture

Adsorption processes have the potential to significantly reduce the CO2 capture cost from power plants and industrial flue gases. InnoSepra has developed several sorbent-based technologies to obtain very high CO2 recovery and high purity CO2 while meeting the EOR/sequestration product specifications. A first-generation process was shown to achieve CO2 recoveries greater than 94% at CO2 purities in the range of 98.5-99.5%. The absolute heat energy required for the process was not only 40% lower than MEA but also was needed at a much lower temperature. This work will present the performance of the second-generation InnoSepra process which is based on a breakthrough sorbent regeneration method. This process has a projected 45% lower capital cost compared to MEA, less than 16% loss in plant output for CO2 capture and compression, and a CO2 capture cost at least 55% lower than MEA. Lab scale testing and the process simulations indicate a CO2 capture performance similar to or better than the first-generation process. Pilot scale drying and breakthrough tests were carried out at the Technology Centre Mongstad (TCM), Norway, and lab-scale cyclic tests were carried out at InnoSepra to confirm the process improvement. During these tests, InnoSepra’s flue gas purification technology was also tested at TCM. It can provide a low-cost option for the removal of NO2 and SOX to sub-ppm levels as well as a significant reduction in aerosol emissions.

08 HYDROGEN↗
DOE OSTI2025

Clay Reimagined: Phyllosilicates as Future Membrane Technologies

Membrane technologies have made critical advances in resource recovery, water purification, and energy systems. However, it is difficult to systematically tune properties of traditional polymer membranes, and researchers have struggled to deliver challenging, advanced separations using these platforms. In recent years, membranes based on 2D materials have drawn attention for molecular-scale separations due to their unique properties, most notably their tunable nanoscale interlayer properties. Among the diverse family of 2D materials, phyllosilicates, a broad class of naturally abundant clay minerals, offer significant advantages in cost and scalability over synthetic 2D materials, positioning them as promising candidates for advanced membrane technologies. Their inherent structural and chemical properties, strategies for tailoring selective transport pathways, and recent advancements across applications including ion separation, water treatment, and energy conversion are discussed. Finally, key challenges and opportunities are outlined to guide future research in leveraging phyllosilicate membranes for high-performance separation technologies.

energy storage and conversion↗
DOE OSTI2025

Unveiling the Role of Critical Impurities in Spent LiFePO 4 Cathodes for Scalable Direct Regeneration

Direct regeneration offers a promising alternative to recycling End-of-Life (EoL) batteries by restoring metal elements and preserving the material structure, yet scaling these technologies to handle practical cathode black mass (CBM) with impurities remains challenging. Here, this study investigates the evolution of impurities, including aluminum (Al), polyvinylidene difluoride (PVDF) binder, and residual carbon (C), during direct recycling of spent LiFePO 4 (LFP) cathodes and their impact on electrochemical performance. Using various ex situ and in situ analyses, it is shown that the formation of lithium fluoride (LiF) during the traditional direct recycling process hinders lithium diffusion and deteriorates the reversible capacity. To address this major challenge, the combination of pH-controlled hydrothermal purification and the two-step sintering process is proposed effectively to regenerate spent LFP cathodes, eliminating the negative effect of Al and fluorine (F) impurities while mitigating any potential impacts of carbon residuals. The regenerated LFP from spent CBM achieves superior performance, retaining 152.5 mAh g −1 at 0.1 C and 133 mAh g −1 at 1 C with 98.7% capacity retention after 200 cycles. This approach is further validated using three distinct waste feedstocks from battery modules, enhancing impurity management and scalability in direct recycling. These findings present a sustainable and economically viable solution for large-scale LFP regeneration.

25 ENERGY STORAGE↗
DOE OSTI2026

Toward Intelligent Multimodal Holography for Real-Time Chemical Imaging of Dynamic Ion Separation

Molecular-level visualization of ion transport and separation dynamics in complex environments is crucial for advancing energy systems, water purification, and critical materials recovery. Achieving this requires imaging platforms that combine structural sensitivity, chemical specificity, and real-time operation. Digital off-axis holography (DOAH) provides high-throughput, label-free quantitative phase imaging but inherently lacks chemical selectivity. Integrating DOAH with complementary spectroscopic channels such as fluorescence or hyperspectral imaging introduces the needed molecular specificity, while also creating challenges in multimodal data fusion, synchronization, and computational throughput. Artificial intelligence offers a powerful route to address these limitations by uniting physics-based reconstruction with data-driven interpretation. In this Perspective, we outline a framework for intelligent multimodal holography and demonstrate its potential using a preliminary AI-driven test case. Raw DOAH holograms of lanthanide solutions subjected to magnetic field gradients were analyzed using multi-agent AI workflows that autonomously selected reconstruction tools, extracted NMF components, and generated scientific claims consistent with true paramagnetic and diamagnetic behavior. This demonstration shows how AI-enabled reasoning can deliver real-time chemical–structural interpretation directly from raw holograms. Together, these advances define a path toward adaptive, intelligent holography platforms capable of supporting in situ chemical separations, dynamic ion transport analysis, and next-generation interfacial science.

Ricchiuti, Giovanna↗
DOE OSTI2025

Repurposing Post-Consumer Polyethylene to Access Cross-Linked Polyethylene with Reprocessabilty, Recyclability, and Tunable Properties

Polyethylene (PE) is the most widely produced plastic but accumulation and resistance to degradation has significantly contributed to the plastic waste crisis. Upcycling has presented promising solutions to transform PE waste into value-added products. In this study, mixed post-consumer PE was successfully repurposed into reprocessable and chemically recyclable cross-linked polyethylene (XLPE). This process involved converting PE into telechelic oligomers, followed by repolymerization using a hybrid cross-linking system consisting of a dynamic cross-linker 2,4,6-triethoxy-1,3,5-triazine (TETA) and non-dynamic cross-linker tris(6-isocyanatohexyl)isocyanurate (Tri-HDI). In the resulting XLPE, TETA facilitated iterative reprocessing with minimal property degradation across cycles, whereas Tri-HDI helped preserve functional performance throughout service life. Compared to PE, XLPE exhibited enhanced mechanical properties, reduced creep deformation under application-relevant temperatures, and high temperature structural stability. Notably, copolymerizing PE oligomers with commercial macrodiols was employed to create composite XLPEs, enabling tuning material properties. After use, XLPE can be efficiently and selectively depolymerized under mild conditions, even when mixed with commercial insulator cables. This depolymerization allows for the recovery of the constituent building blocks, enabling purification and subsequent repolymerization for reuse. This approach demonstrates the potential of repurposing plastic waste into sustainable materials and fostering the development of a circular economy.

INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CHEMI↗
DOE OSTI2025

Upcycling of Waste Plastics into Carboxylic Acids for Biodegradable Surfactants

This work outlines a process for producing high‐purity (>95%) carboxylate surfactants from post‐consumer recycled high‐density polyethylene (PCR‐HDPE). The approach involves the thermal depolymerization of PCR‐HDPE via pyrolysis, followed by fractional distillation to isolate C9–C14 olefins. These olefins undergo hydroformylation using cobalt carbonyl catalysts to generate aldehydes, which are subsequently oxidized to carboxylic acids using Pinnick oxidation under mild aqueous‐phase conditions. Neutralization of the resulting carboxylic acids with sodium hydroxide produces plastic‐derived carboxylate surfactants (PDCs) in the form of sodium carboxylates. Subsequent purification steps ensure surfactant‐grade purity and enable accurate assessment of physicochemical properties. The resulting PDCs are evaluated for critical micelle concentration (CMC), foamability, surface tension reduction, and calcium ion tolerance, demonstrating competitive behavior with conventional anionic carboxylate surfactants. This route provides a sustainable alternative for surfactant production, reducing reliance on fossil‐derived feedstocks and valorizing plastic waste streams through chemical upcycling.

Biodegradable surfactants↗
DOE OSTI2026

Selective Sequential Depolymerization of Mixed Plastics Mediated by Photothermal Conversion

Chemical recycling of plastics into monomers is a promising strategy to achieve a circular economy. However, selective depolymerization methods for mixed plastics are still underdeveloped. Herein, we report a selective and sequential depolymerization strategy for mixed plastics, including poly(L-lactide) (PLLA), polystyrene (PS), and poly(ethylene terephthalate) (PET), using photothermal conversion. We were able to selectively depolymerize PLLA into L-lactide in the presence of PS and PET. Then, PS was selectively depolymerized to styrene, followed by the depolymerization of PET into its monomer. Our protocol was carried out in one pot without any additional purification of the unreacted plastics at each stage. This method was successfully applied to mixtures of post-consumer waste plastic.

carbon black↗
DOE OSTI2025

Solventless Dual‐Cure Liquid Resins Via Circular Use of Phthalic Anhydride for Recyclable Composite Applications

Abstract Fiber‐reinforced composites (FRCs) possess a remarkable strength‐to‐weight ratio, making them ideal light‐weighing alternative materials of metals used in automotive, aerospace, and outdoor equipment applications, but their recycling is challenging. Chemically recyclable thermoset polymers can enable fiber recovery and reuse; however, challenges remain in the separation and purification of depolymerized small molecules for efficient polymer recycling. To this end, a series of liquid resins for chemically recyclable polymer networks is designed based on phthalic anhydride, a widely produced and inexpensive chemical. The straightforward sublimation of phthalic anhydride is leveraged to enable a simple and efficient separation process for polymer recycling. To liquefy phthalic anhydride, five mono‐acryloyl‐phthalates are synthesized to obtain stable liquid resins together with phthalic diglycidyl ester. These liquid resins undergo dual‐cure reactions that comprise photopolymerization of acrylate and, subsequently, heat‐mediated epoxy‐acid polymerization reactions. These liquid resins exhibit moderate viscosities (2600–6400 cP @ 22 °C), fast curing, and robust thermomechanical properties (T g s from 71 to 116 °C). It is demonstrated that hydrolysis of the dual‐cured polymers completes within 2 h at 80 °C, and direct sublimation produces phthalic anhydride with 82% yield. This resin system is expected to provide a cost‐competitive, highly efficient platform for recyclable FRCs.

Polymer Science↗
DOE OSTI2025

New Synthetic Route to 4,6‐Diamino‐5,7‐dinitro‐benzo‐furazan, Important Decomposition Product of 1,3,5‐Triamino‐2,4,6‐trinitrobenzene

The important 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) decomposition byproduct, 4,6-diamino-5,7-dinitro-benzo-furazan (F 1 ), was prepared in a four-step reaction sequence starting with commercially available materials through a key intermediate, 4,6-dichloro-5,7-dinitro-benzo-furazan. The introduction of azido to 4,6-dichloro-benzo-furazan, followed by nitration and amination gave F 1 in good yield. This new method showed a greatly improved yield and ease of purification than previous methods (the total yield was 30%–40% in seven steps). F 1 is a stable yellow solid with a melting point of 308.7°C and a thermal decomposing temperature of 310.3°C (differential scanning calorimetry at 10°C/min heating rate). The solid-state structure was solved by single-crystal X-ray analyses at low temperatures (100 K). The compound crystallizes in a P 2 1 c space group with the formula C 6 H 4 N 6 O 5 •H 2 O with 12 molecules of F 1 /H 2 O in the unit cell. This compound has eluded complete characterization for almost 50 years. With this information, more advanced decomposition models can be created to further improve critical safety margins in handling the energetic material, TATB.

decomposition↗