Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymerization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Ignition Resistance of Polymeric Materials to Particle Impact in High-Pressure Oxygen

Particle impact ignition has been the primary cause of numerous fires in oxygen systems. This ignition phenomenon is known to occur where particles are present in high-velocity gas, and where impact occurs on a flammable material. The particle impact ignition behavior of many metals has been widely studied, but the particle impact ignition behavior of polymeric materials is relatively unknown. Particle impact ignition in polymeric materials is a concern as these materials are commonly used in component seat and seal applications, where high-velocity particle impacts can occur. This study evaluates several polymeric materials and compares the minimum temperature required for ignition (threshold temperature) of these materials: Kel-F 81 (CTFE), Teflon (PTFE), PEEK, Vespel SP-21, and Nylon 6/6. The materials were configured as targets in the White Sands Test Facility high-velocity particle impact test system. Gaseous oxygen was flowed at 4000 psi and sonic velocity, and the targets were impacted with 2000-micron aluminum 2017 particles. This paper discusses the results of these tests and ranks the materials according to their threshold temperatures at these conditions.

Forsyth, Elliot T.↗
NASA NTRS2001

Influence of Solutocapillary Convection on Macrovoid Defect Formation in Polymeric Membranes

Macrovoids (MVs) are large (10-50 micrometers) pores often found in polymeric membranes prepared via phase-inversion techniques. They are generally considered undesirable, as they adversely affect the permeability properties and performance of polymeric membranes for microfiltration, ultrafiltration, and reverse osmosis. However, MVs can be useful in certain thin-film applications in which vapor transmission is necessary, or for use as reservoirs for enzymes or liquid membrane material. If more could be learned about the nature and causes of MV formation, it might be possible to devise techniques to control and/or prevent MV formation that are more effective than those currently employed. Two hypotheses for the MV growth mechanism have been advanced. Reuvers proposed that once initiated, MV growth can be attributed to diffusion of (primarily) solvent to the MV nuclei. Because this mechanism does not involve gross movement of the MV, the presence or absence of body forces such as buoyancy should not significantly affect MV growth. On the other hand, Shojaie et al. proposed that solutocapillary convection induced by a steep surface-tension gradient along the MV/bulk solution interface enhances mass transfer to the growing MV. This interfacial convection exerts a force that pulls the growing MV downward into the casting solution. Both buoyancy and viscous drag hinder MV growth by inhibiting this motion. Thus, removing the buoyancy force by casting in microgravity should augment MV growth according to this hypothesis. Whereas neither surface tension nor gravity has a significant effect on MV growth according to the first hypothesis, buoyancy forces should be important if the second hypothesis is correct. The overall goal of this research is to test these two hypotheses in order to improve our understanding of the MV growth processing solvent-cast polymeric membranes. Studying MV growth in low-gravity conditions is pivotal to our ability to discriminate between these two hypotheses.

Pekny, M. R.↗
NASA NTRS2001

Frontal Polymerization in Microgravity: Bubble Behavior and Convection on the KC-135 Aircraft

Frontal polymerization is a mode of converting monomer into polymer via a localized exothermic reaction zone that propagates through the coupling of thermal diffusion and Arrhenius reaction kinetics. Frontal polymerization was discovered in Russia by Chechilo and Enikolopyan in 1972. The macrokinetics and dynamics of frontal polymerization have been examined in detail and applications for materials synthesis considered. Large temperature and concentration gradients that occur in the front lead to large density gradients. A schematic is presented for a liquid monomer, usually a monoacrylate, being converted to a liquid (thermoplastic) polymer. The velocity can be controlled by the initiator concentration but is on the order of a cm/min. If the liquid monomer is multifunctional, then a solid (thermoset) polymer is formed. Convection can occur with all types of monomers if the front propagates up a tube. Bowden et al. studied liquid/solid systems. McCaughey et al. studied liquid polymer systems. Descending fronts in thermoplastic systems are also susceptible to the Rayleigh-Taylor instability.

Pojman, John A.↗
NASA NTRS2002

Molecular Probe Fluorescence Monitoring of Polymerization

This project investigated the feasibility of using fluorescence spectroscopy to determine viscosity of polymer/monomer in support of Transient Interfacial Phenomena in Miscible Polymer Systems (TIPMPS). This project will attempt to measure gradient induced flow at a miscible interface during and / or after in-flight polymerization of dodecyl acrylate (lauryl acrylate). Concentration and temperature gradients will be intentionally introduced during polymerization and the resultant fluid flow determined by Particle Imaging Velocimetry (PIV). This report describes an investigation of the feasibility of using fluorescence of a probe molecule to monitor viscosity and/or concentration during and after polymerization. The probe used was pyrene which has been shown to be sensitive to its local environment in methyl methacrylate.

Patrick Bunton↗
NASA NTRS2003

Influence of Solutocapillary Convection on Macrovoid Defect Formation in Polymeric Membranes

The focus of this research project involved the dry-cast process for polymeric membrane formation, whereby evaporation of solvent from an initially homogeneous polymer/solvent/ nonsolvent solution results in phase separation and the formation of polymer-rich and polymer-lean phases. Under certain conditions the polymer-lean phase gives rise to very large and usually undesirable, tear-drop-shaped pores (size approx. 10 - 50 microns) termed macrovoids (MVs). Although in many cases the presence of MV pores has deleterious effects on membrane performance, there are a number of innovative applications where the presence of such pores is highly desirable. Although researchers have proposed a variety of mechanisms for MV formation over the past three decades, two main hypotheses are currently favored: one asserts that MV growth can be attributed solely to diffusion (the diffusive growth hypothesis), whereas the other states that solutocapillary convection (the SC hypothesis) at the MV interface contributes to growth. The overall goal of this research was to obtain a more comprehensive understanding of the fundamental mechanism of MV growth. This research incorporates a coupled modeling and experimental approach to test a solutocapillary convection hypothesis for the growth of macrovoid pores in polymeric membranes. Specifically, we utilized a modification of the first principles model developed by two of the PIs (ARG and WBK) for dry-cast CA membranes. For the experimental component, two separate and mutually complementary approaches were used to study MV growth. In the first, membranes cast in a zero-g environment aboard the NASA KC-135 aircraft were compared with those cast on the ground to assess the effect of the buoyancy force on membrane morphology and MV size and shape. In the second approach, videomicroscopy flow visualization (VMFV) was utilized to observe MV formation and growth in real time and to assess the effect of surface tension on the MV growth dynamics. As a result of these fundamental studies, our research group advanced a new hypothesis for MV pore development in polymeric membranes.

Greenberg, Alan R.↗
NASA NTRS2003

Functional nanocomposites prepared by self-assembly and polymerization of diacetylene surfactants and silicic acid

Conjugated polymer/silica nanocomposites with hexagonal, cubic, or lamellar mesoscopic order were synthesized by self-assembly using polymerizable amphiphilic diacetylene molecules as both structure-directing agents and monomers. The self-assembly procedure is rapid and incorporates the organic monomers uniformly within a highly ordered, inorganic environment. By tailoring the size of the oligo(ethylene glycol) headgroup of the diacetylene-containing surfactant, we varied the resulting self-assembled mesophases of the composite material. The nanostructured inorganic host altered the diacetylene polymerization behavior, and the resulting nanocomposites show unique thermo-, mechano-, and solvatochromic properties. Polymerization of the incorporated surfactants resulted in polydiacetylene (PDA)/silica nanocomposites that were optically transparent and mechanically robust. Molecular modeling and quantum calculations and (13)C spin-lattice relaxation times (T(1)) of the PDA/silica nanocomposites indicated that the surfactant monomers can be uniformly organized into precise spatial arrangements prior to polymerization. Nanoindentation and gas transport experiments showed that these nanocomposite films have increased hardness and reduced permeability as compared to pure PDA. Our work demonstrates polymerizable surfactant/silica self-assembly to be an efficient, general approach to the formation of nanostructured conjugated polymers. The nanostructured inorganic framework serves to protect, stabilize, and orient the polymer, mediate its performance, and provide sufficient mechanical and chemical stability to enable integration of conjugated polymers into devices and microsystems.

NASA Discipline Life Support Systems↗
NASA NTRS1991

Monodisperse, polymeric microspheres produced by irradiation of slowly thawing frozen drops

Monodisperse, polymeric microspheres are formed by injecting uniformly shaped droplets of radiation polymerizable monomers, preferably a biocompatible monomer, having covalent binding sites such as hydroxyethylmethacrylate, into a zone, impressing a like charge on the droplet so that they mutually repel each other, spheroidizing the droplets within the zone and collecting the droplets in a pool of cryogenic liquid. As the droplets enter the liquid, they freeze into solid, glassy microspheres, which vaporizes a portion of the cryogenic liquid to form a layer. The like-charged microspheres, suspended within the layer, move to the edge of the vessel holding the pool, are discharged, fall and are collected. The collected microspheres are irradiated while frozen in the cryogenic liquid to form latent free radicals. The frozen microspheres are then slowly thawed to activate the free radicals which polymerize the monomer to form evenly-sized, evenly-shaped, monodisperse polymeric microspheres.

Rhim, Won-Kyu↗
NASA NTRS1990

Production of monodisperse, polymeric microspheres

Very small, individual polymeric microspheres with very precise size and a wide variation in monomer type and properties are produced by deploying a precisely formed liquid monomer droplet, suitably an acrylic compound such as hydroxyethyl methacrylate into a containerless environment. The droplet which assumes a spheroid shape is subjected to polymerizing radiation such as ultraviolet or gamma radiation as it travels through the environment. Polymeric microspheres having precise diameters varying no more than plus or minus 5 percent from an average size are recovered. Many types of fillers including magnetic fillers may be dispersed in the liquid droplet.

Rembaum, Alan↗
NASA NTRS2009

Light-Driven Polymeric Bimorph Actuators

Light-driven polymeric bimorph actuators are being developed as alternatives to prior electrically and optically driven actuators in advanced, highly miniaturized devices and systems exemplified by microelectromechanical systems (MEMS), micro-electro-optical-mechanical systems (MEOMS), and sensor and actuator arrays in smart structures. These light-driven polymeric bimorph actuators are intended to satisfy a need for actuators that (1) in comparison with the prior actuators, are simpler and less power-hungry; (2) can be driven by low-power visible or mid-infrared light delivered through conventional optic fibers; and (3) are suitable for integration with optical sensors and multiple actuators of the same or different type. The immediate predecessors of the present light-driven polymeric bimorph actuators are bimorph actuators that exploit a photorestrictive effect in lead lanthanum zirconate titanate (PLZT) ceramics. The disadvantages of the PLZT-based actuators are that (1) it is difficult to shape the PLZT ceramics, which are hard and brittle; (2) for actuation, it is necessary to use ultraviolet light (wavelengths < 380 nm), which must be generated by use of high-power, high-pressure arc lamps or lasers; (3) it is difficult to deliver sufficient ultraviolet light through conventional optical fibers because of significant losses in the fibers; (4) the response times of the PLZT actuators are of the order of several seconds unacceptably long for typical applications; and (5) the maximum mechanical displacements of the PLZT-based actuators are limited to those characterized by low strains beyond which PLZT ceramics disintegrate because of their brittleness. The basic element of a light-driven bimorph actuator of the present developmental type is a cantilever beam comprising two layers, at least one of which is a polymer that exhibits a photomechanical effect (see figure). The dominant mechanism of the photomechanical effect is a photothermal one: absorption of light energy causes heating, which, in turn, causes thermal expansion.

Adamovsky, Gregory↗
NASA NTRS2007

Rapid Engineering of Three-Dimensional, Multicellular Tissues With Polymeric Scaffolds

A process has been developed for the rapid tissue engineering of multicellular-tissue-equivalent assemblies by the controlled enzymatic degradation of polymeric beads in a low-fluid-shear bioreactor. In this process, the porous polymeric beads serve as temporary scaffolds to support the assemblies of cells in a tissuelike 3D configuration during the critical initial growth phases of attachment of anchorage-dependent cells, aggregation of the cells, and formation of a 3D extracellular matrix. Once the cells are assembled into a 3D array and enmeshed in a structural supportive 3D extracellular matrix (ECM), the polymeric scaffolds can be degraded in the low-fluid-shear environment of the NASA-designed bioreactor. The natural 3D tissuelike assembly, devoid of any artificial support structure, is maintained in the low-shear bioreactor environment by the newly formed natural cellular/ECM. The elimination of the artificial scaffold allows normal tissue structure and function.

Gonda, Steve R.↗
NASA NTRS2011

Polymerization initated at sidewalls of carbon nanotubes

The present invention is directed to aryl halide (such as aryl bromide) functionalized carbon nanotubes that can be utilized in anionic polymerization processes to form polymer-carbon nanotube materials with improved dispersion ability in polymer matrices. In this process the aryl halide is reacted with an alkyllithium species or is reacted with a metal to replace the aryl-bromine bond with an aryl-lithium or aryl-metal bond, respectively. It has further been discovered that other functionalized carbon nanotubes, after deprotonation with a deprotonation agent, can similarly be utilized in anionic polymerization processes to form polymer-carbon nanotube materials. Additionally or alternatively, a ring opening polymerization process can be performed. The resultant materials can be used by themselves due to their enhanced strength and reinforcement ability when compared to their unbound polymer analogs. Additionally, these materials can also be blended with pre-formed polymers to establish compatibility and enhanced dispersion of nanotubes in otherwise hard to disperse matrices resulting in significantly improved material properties. The resultant polymer-carbon nanotube materials can also be used in drug delivery processes due to their improved dispersion ability and biodegradability, and can also be used for scaffolding to promote cellular growth of tissue.

Tour, James M.↗
NASA NTRS2018

Testing of Candidate Polymeric Materials for Compatibility with Pure Alternate Pretreat as Part of the Universal Waste Management System (UWMS)

The Universal Waste Management System (UWMS) is an improved Waste Collection System for astronauts living and working in low Earth orbit spacecraft. Polymeric materials used in water recovery on International Space Station are regularly exposed to phosphoric acid-treated 'pretreated' urine. Polymeric materials used in UWMS are not only exposed to pretreated urine, but also to concentrated phosphoric acid with oxidizer before dilution known as 'pure pretreat.' Samples of five different polymeric materials immersed in pure pretreat for 1 year were tested for liquid compatibility by measuring changes in storage modulus with a dynamic mechanical analyzer.

Wingard, C. D.↗
NASA NTRSDate not supplied

Modeling Ring-Opening Polymerization with Machine-Learned Committors

Many important industrial and biological processes depend on ring-opening polymerization (ROP), including large-scale production polymers, such as nylon 6, and a variety of biodegradable polymers and high-performance resins. Large-scale simulations (>200K atoms) of ROP were performed using a deep neural network-based method that captured the effect of the local chemical environment of the reactive sites using training data from quantum chemical methods. The utility of this method was demonstrated by modeling the cationic ROP of bis-benzoxazine, a promising resin for use in advanced high-temperature application composites (>200°C). Density functional theory calculations were used to map out the various ring opening and polymerization reaction paths that occur during the thermal processing of bis-benzoxazine. The probabilities of these reactions, as a function of local atomic configurations, were used to construct committor functions using a neural network approach. The learned committor functions were then used to determine when a particular reaction occurred within the REACTER framework for reactive molecular dynamics simulations. The experimentally observed exotherm that occurs during bis-benzoxazine ROP was captured in an effective manner in the simulations by imposing a local heating of the system that corresponds to the enthalpy of reaction for each reaction. The dependence of the final polymer morphology on the ROP reaction temperature was analyzed at the molecular scale. The results presented in this work indicate that machine-learned committor functions are a promising approach for incorporating high-fidelity reactivity criteria that capture the effect of local chemical environments into large-scale polymerization simulations.

machine learning, polymer simulations, molecular d↗
DOE OSTI2024

Reactive Processing of Furan‐Based Monomers via Frontal Ring‐Opening Metathesis Polymerization for High Performance Materials

Frontal ring-opening metathesis polymerization (FROMP) presents an energy-efficient approach to produce high-performance polymers, typically utilizing norbornene derivatives from Diels–Alder reactions. This study broadens the monomer repertoire for FROMP, incorporating the cycloaddition product of biosourced furan compounds and benzyne, namely 1,4-dihydro-1,4-epoxynaphthalene (HEN) derivatives. A computational screening of Diels–Alder products is conducted, selecting products with resistance to retro-Diels–Alder but also sufficient ring strain to facilitate FROMP. The experiments reveal that varying substituents both modulate the FROMP kinetics and enable the creation of thermoplastic materials characterized by different thermomechanical properties. Moreover, HEN-based crosslinkers are designed to enhance the resulting thermomechanical properties at high temperatures (>200 °C). The versatility of such materials is demonstrated through direct ink writing (DIW) to rapidly produce 3D structures without the need for printed supports. This research significantly extends the range of monomers suitable for FROMP, furthering efficient production of high-performance polymeric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reactive extrusion of frontally polymerizing continuous carbon fiber reinforced polymer composites

The manufacturing of carbon fiber-reinforced polymer (CFRP) composites demands rapid and energy-efficient strategies. Frontal polymerization (FP) enables the manufacturing of CFRP using dicyclopentadiene (DCPD) thermoset polymer which meets these requirements. In this work, we introduce reactive extrusion of CFRP (RE-CFRP), where two rollers provide localized heat and pressure to sustain the curing reaction and the consolidation of a continuous carbon fiber tow pre-impregnated with DCPD. We study the effect of the extrusion speed, temperature, and compaction force on the properties of the produced CFRP. Mechanical testing confirms that the resulting fiber volume fraction and the elastic modulus are similar to bulk cured tows. A homogenized thermo-chemical model is developed to study the effect of the process parameters on the polymerization reaction. The process produces hollow woven composite tubes directly via extrusion and in situ curing. Overall, this process offers advantages in curing, tooling, speed, and energy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Bidirectional Suzuki Catalyst Transfer Polymerization of Poly( p -phenylene)

Suzuki catalyst transfer polymerization (SCTP) has emerged as an effective method for accessing length-controlled π-conjugated poly(p-phenylene). Regio-controlled functional group sequencing along the backbone and the chain ends of synthetic polymers remains a challenge for the successful integration of organic semiconductors in sensors and electronic devices. Here, we report a bidirectional SCTP system based on dinuclear palladium(II) initiators. Functional groups transferred during the initiation and termination steps unlock independently addressable synthetic handles at the polymer core and respective chain ends. These functional groups open opportunities for late-stage regio-controlled and chemoselective derivatizations. Control over key polymer parameters, including molecular weight (M n ), dispersity ( Đ = M w /M n ), degree of polymerization ( DP ), termination efficiency, and functional group interconversion, is corroborated by size exclusion chromatography (SEC) and NMR spectroscopy. The modular design of SCTP initiators, in combination with commercially available terminating groups, represents a highly flexible toolbox for late-stage polymer conjugation, e.g., chemoselective anchoring groups for integration with functional electronics or bioorthogonal conjugation for molecular sensing.

Aldehydes↗
DOE OSTI2025

Equilibrium-gated pattern formation: How molecular dissociation thermodynamics drive emergent behavior in dissipative polymeric systems

Emergent patterns in biological systems arise through dissipative processes that balance reaction and transport phenomena, producing highly functional properties from self-regulating mechanisms. Synthetic fabrication, by contrast, often relies on user-controlled, multistep methods that lack the self-organizing capabilities of natural systems. Inspired by nature, we sought chemical systems that integrate strongly coupled reaction and transport phenomena, identifying frontal ring-opening metathesis polymerization (FROMP) as a method capable of creating diverse forms and functions through reactive processing. By employing discrete molecular initiators, FROMP allows precise control of key reaction steps—inhibition, initiation, and propagation. Using an integrated computational and experimental framework, we uncover how near-equilibrium inhibition dynamics, coupled with far-from-equilibrium reaction kinetics, drive pattern formation in frontally polymerized synthetic materials. We propose the concept of equilibrium-gated pattern formation, demonstrating how initiator chemistry can be tuned to achieve programmable macroscale properties. Our study reveals a surprising insight: Emergent behavior in FROMP systems arises from the inhibition-dominated regime of resin composition, expanding prior observations that such behavior is confined to a narrow compositional space near the boundary between front quenching and uniform front propagation. We identify a broader compositional window, far from the quenching regime, where emergent behavior reliably manifests. This expanded design space significantly enhances the operational flexibility of reactive systems and their capacity for self-organization. Furthermore, these insights provide a roadmap for designing bioinspired materials with self-organizing capabilities, unlocking possibilities in synthetic manufacturing.

Architected Polymers↗
DOE OSTI2026

A Review of Polymeric Nanoparticle Design, Synthesis, and Biomedical Applications

Polymeric nanoparticles (PNPs) are solid particles that contain macromolecular polymers ranging in size from 1-1000 nm. They have a wide variety of structures that are determined by their identity as either natural biopolymers, synthetic polymers or a combination of both. In the design of PNPs, the polymeric system, size, internal structure, additional molecules, and synthetic pathway can be engineered, allowing for a multitude of properties including differing responses to physiological environments and the incorporation of a drug. The easily accessible fine tuning of PNPs allows for a multitude of applications in medicine. PNPs allow for increased pharmacokinetics, efficacy, safety, and targeting strength when utilized as carriers for drugs. Currently there are a wide range of PNPs approved by the Food and Drug Administration for use in clinical settings and many more being investigated in clinical studies. There is also research that is being conducted for the usage of PNPs in controlled drug delivery systems and as carriers through the blood brain barrier to aid in treating neurological diseases.

60 APPLIED LIFE SCIENCES↗