Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Permeation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Scaling dynamics in low-salt-rejection reverse osmosis for high-salinity produced water desalination: Mechanistic modeling and membrane autopsy

Membrane scaling remains a critical barrier to the reliable operation of desalination systems, particularly for hypersaline produced water (PW) treatment. This study fills the knowledge gap of autopsy-based model validation for PW desalination by elucidating scaling mechanisms in a Low-Salt-Rejection Reverse Osmosis (LSRRO) system through the integration of pilot-scale experimentation and complementary modeling approaches. A semi-empirical modeling framework was developed and applied to a multistage pilot LSRRO system equipped with nanofiltration and RO membranes treating high-salinity PW from the Permian Basin. Water quality analysis showed that total dissolved solids decreased from ~130,000 mg/L to ~1900 mg/L in the permeate, then further reduced to ~300 mg/L by a second-pass RO. Two different thermodynamic modeling approaches were evaluated: the first extends the LSRRO framework by incorporating system complexity and scaling phenomena, whereas the second method explicitly captures concentration polarization in localized supersaturation. Both methods illustrate the tendency for carbonate and sulfate scaling throughout the stages. Membrane autopsies revealed a silica-dominated deposit matrix, localized CaSO 4 at Stage 2, and minor barite/celestite despite their prominence in model predictions. Quantum-chemical calculations indicated silica scaling can be rationalized by favorable adsorption of H 4 SiO 4 on Fe-oxide surfaces (ΔG ≈ −44 kJ/mol), providing a kinetic pathway for interfacial inorganic polymerization even when bulk equilibrium predictions are conservative. Overall, the thermodynamic scaling modeling and membrane autopsy revealed heterogeneous, localized deposits with limited impact on LSRRO performance, while quantum analysis rationalized the thermodynamically unfavorable precipitation formation under bulk equilibrium, reconciling model–autopsy discrepancies. These insights support targeted pretreatment and silica-specific antiscalants to extend membrane lifetime and increase recovery, providing a transferable framework for hypersaline water desalination systems. The combined experimental–computational approach provides new mechanistic insight into scaling in hypersaline membrane systems and establishes a transferable framework for predicting and mitigating scaling in next-generation desalination technologies.

Low-salt-rejection reverse osmosis↗
DOE OSTI2025

Logical approach to tritium vacuum pump selection for fusion applications

Vacuum pumps have been used for tritium processing since the 1940s following the isolation of pure tritium. The largest problem facing tritium vacuum pumps is the tritium radioactive decay. The beta particles, recoil energy, and subsequent radical formations are detrimental to most carbon-based materials. Carbon materials, such as plastics, elastomers, carbon fiber, activated carbon, etc., react with tritium to form methane and in the process strip material from the carbonbased material. Other reactions can be self-catalyzing, as is the case with nitrogen and tritium forming tritiated ammonia at room temperature and pressure. Tritium also readily isotopically exchanges with surface -OH groups, increasing the amount of protium in the gas stream while creating a tritium holdup on the surface. Metals are the preferred material when working with tritium, but tritium will permeate into and through almost all metals at some point. The entrapped tritium can decay inside the metal, creating local helium distortions that can impact the structural properties above and beyond the hydrogen embrittlement issue tritium can cause.

Angelette, Lucas M. [Savannah River National Labor↗
DOE OSTI2025

Linking structure to performance: Characterization of porous transport layers for high-pressure water electrolysis

Proton exchange membrane (PEM) water electrolysis is a promising technology to produce cost-efficient hydrogen. PEM electrolyzers offer a large current density range and the ability to operate at differential pressure which can be used to minimize both capital and operational expenditures. However, directly producing pressurized hydrogen at the cathode results in pushing the membrane against the anode porous transport layer (PTL). This can lead to detrimental effects, such as membrane deformation or ruptures, which depend on membrane properties as well as PTL material properties such as pore size, structure, and morphology. In this work, a range of sinter and felt-based commercial PTLs are evaluated for their contributions to the cell's electrochemical and H 2 crossover performance at cathode pressures up to 30 bar. X-ray tomography and post-operando optical microscopy are used to assess the morphology of the PTLs, and the PTL induced deformation experienced by the catalyst coated membrane (CCM), respectively. PTL samples with lower porosity were found to reduce both the cell voltage and the amount of H 2 permeating from the cathode to the anode exhaust, which was ascribed to improved catalyst layer contact and reduced membrane deformation, respectively. The best performing PTLs improved electrolyzer efficiency by ~1.5 kWh/kg H2 . Specifically, 1 kWh/kg H2 was gained due to reducing membrane deformation and decreasing H 2 crossover. The remainder 0.5 kWh/kg H2 were achieved by improving the electrical contact at the electrode/PTL interface which decreased cell voltage.

08 HYDROGEN↗
DOE OSTI2024

In-situ kinetic study of irradiation induced crystallization in amorphous Al 2 O 3

In the last ten years amorphous alumina coatings, deposited by Pulsed Laser Deposition, emerged as potential key enabling technology in the fields of heavy liquid metal fast reactors (lead and lead-bismuth) and fusion. In the former, as coating of the steel fuel cladding and in the latter as multifunctional coating providing a barrier against tritium permeation, steel corrosion and electrical insulation. Nevertheless, a detailed knowledge of the behavior of this thermodynamically metastable material at high temperatures and under neutron irradiation is still unknown. A knowledge gap that is mandatory to fill up for the deployment of this barrier technology. In the present work, we present a first step towards this goal, by the in-situ dynamic observation of the radiation induced crystallization processes of thin films of amorphous Al 2 O 3 , induced by ion-irradiation over an extensive range of temperatures (400-800 °C). The study was performed at the Intermediate Voltage Electron Microscope (IVEM)-Tandem Facility at Argonne National Laboratory. The experimental findings allow to elucidate the dependence of the grain growth on ion dose and temperature. A kinetic approach has been used to derive the process activation energies and other important parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Elongated Fullerene Unlocks Oxygen-Resistant Perovskite Solar Minimodules

State-of-the-art encapsulation cannot prevent the permeation of oxygen into perovskite solar cells (PSCs). Here, we report the finding that p-i-n structured PSCs degrade quickly under oxygen exposure. Oxidation of C60, rather than perovskites, dominates the degradation. Chemical absorption of oxygen by C60 is identified, which impairs its electron transport property. We modify the electron transport layers to address the instability under oxygen exposure. The elongated fullerene C70 is found to react with oxygen orders of magnitude slower than C60. In combination with a compact SnO2 buffer fabricated by atomic layer deposition, which can slow down the oxygen diffusion, the resulting unencapsulated PSCs with C70 retained 90% of their initial efficiency after 1-sun illumination in pure oxygen for 1,200 h at 70 degrees C, improving stability by hundreds of times. Testing of unencapsulated perovskite minimodules of different perovskite compositions with C70 gives extrapolated lifetimes of 17-41 years at 50 degrees C.

14 SOLAR ENERGY↗
DOE OSTI2025

Self-regulating behavior of hybrid membrane systems as demonstrated in an element-scale forward osmosis-reverse osmosis hybrid system

Hybrid membrane systems can be difficult to design due to the requisite flow rate matching between up- and downstream unit operations. In this work, we use a forward osmosis-reverse osmosis (FO-RO) hybrid system to demonstrate how some membrane systems can exhibit self-regulating behavior due to osmotic coupling. This can reduce the need for complex control systems for flow balancing. We show this behavior using a module-scale test bed that can mimic the behavior of larger scale operations. The system shows permeate flow rate near-convergence between the FO and RO modules after startup or when perturbed by a change in RO module pressure. The behavior of this hybrid system demonstrates that some membrane operations can exploit osmotic interdependence, rather than expensive control systems, to achieve steady state operation.

Debottlenecking↗
DOE OSTI2025

Experimental observation of nonlinear relation between pressure and water flux is consistent with the solution-diffusion model

In several recent studies, it has been proposed that the fundamental understanding of penetrant transport in dense polymer membranes occurring via the solution-diffusion model, which has been the generally accepted theoretical framework for describing penetrant transport in such materials for the past several decades, is flawed. An alternate mechanistic framework based on the idea of two-phase flow in a porous medium (i.e., pore-flow) has been broadly advanced instead, with proponents of this approach claiming that the pore-flow theoretical framework provides the necessary mechanistic insight to design novel polymeric membrane materials for emerging applications. In this study, we show experimental results for hydraulic permeation of water that are entirely consistent with the solution-diffusion theory, without modification, for three dense polymeric membranes: crosslinked poly(ethylene glycol diacrylate) (XLPEGDA), Nafion 117 ionomer in the sodium counterion form (Nafion 117-Na), and cellulose acetate (CA). By measuring water flux at transmembrane pressures up to 240 bar, we observe a nonlinear relationship between the transmembrane pressure (TMP) and water flux, J w , for XLPEGDA and Nafion 117-Na, while this relationship is linear for CA. We demonstrate that the behavior of these three materials is described via the solution-diffusion model. According to the solution-diffusion model, flux is, to a good approximation, proportional to the transmembrane concentration difference induced by the pressure difference across the membrane, rather than to TMP itself. Water sorption isotherms are reported for all three materials. They further justify the nonlinear relationship between TMP and J w observed in XLPEGDA and Nafion 117-Na, emphasizing that the nonlinearity in the flux/TMP relationship stems from nonlinearities in the sorption isotherm with pressure. Additionally, the relationship between water flux and TMP can be predicted, a priori, with no adjustable parameters when a predictive model for the diffusion coefficient of water is employed in conjunction with the experimental water sorption isotherms in the solution-diffusion model. Furthermore, our results demonstrate the validity of the solution-diffusion model to describe transport of penetrants in dense polymer membranes, while highlighting the sensitivity of the solution-diffusion model to the many physical and mathematical simplifications commonly applied to the theory in literature.

materials↗
DOE OSTI2025

Ultra-selective CANAL Polymers for Hydrogen-based Membrane Separations after Long-Term Aging

Hydrogen is a critically important molecule in the chemicals and energy industries, driving the need for efficient purification technologies such as membrane-based separations. However, polymer membranes often suffer from physical aging, leading to decreased gas permeability over time. This study leverages the unique aging behavior of contorted microporous polymers, synthesized via catalytic arene-norbornene annulation (CANAL) polymerization, to enhance molecular sieving for H 2 separations. While prior studies demonstrated a 1000% increase in H 2 /CH 4 selectivity with minimal permeability loss over 150 days, we extend this investigation to hyperaged (∼1 year) CANAL polymers and evaluate their performance under various conditions of industrial relevance. We report a remarkable 6100% increase in H 2 /CH 4 selectivity and a 2400% improvement in H 2 /N 2 selectivity, with only a 55% decline in H 2 permeability. These membranes exhibit excellent long-term stability in binary and ternary gas mixtures and at elevated temperatures. Additionally, extended aging enhances H 2 /CO 2 selectivity beyond the 2008 upper bound due to improved size-sieving. High-temperature permeation experiments and grand canonical Monte Carlo simulations reveal that H 2 permeability increases from 570 to 3500 barrer as the temperature rises from 35 °C to 190 °C, while H 2 /CO 2 selectivity declines from 14 to 3 due to the higher diffusion activation energy of CO 2 . Despite this tradeoff, hyperaged CANAL membranes maintain performance beyond the 200 °C upper bound, having selectivity–permeability performance comparable to many state-of-the-art membranes for H 2 /CO 2 separations. As a result, this study highlights the robustness and industrial viability of ultra-selective CANAL polymers for hydrogen purification, contributing to advancements in clean energy and sustainable separation technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Direct ink writing of shear exfoliated two-dimensional nanomaterial- elastomeric multifunctional nanocomposite

Direct ink writing (DIW) of polymer nanocomposites with high loadings of two-dimensional (2D) nanofillers (graphene and hexagonal boron nitride (hBN)) is challenging because of potential clogging, use of hazardous solvents, and agglomeration. Here, in this work, a shear exfoliation and sieving method to prepare DIW ink with high loading of nanofillers produced from low-cost bulk layered materials such as graphite and bulk hBN powder for successful DIW printing without the use of any solvents, binders, or plasticizers. The single-step exfoliation technique resulted in a composite with substantial layer reduction along the c-axis, as confirmed by SEM, TEM, XRD, and Raman analysis. Incorporating exfoliated graphene (40 wt%) increased viscosity by ∼6 orders of magnitude due to enhanced particle–matrix interactions, leading to pronounced yield stress behavior and a yield stress of approximately 1598 Pa, which enabled excellent shape retention during extrusion. Using the DIW technique, porous structures such as desalination membranes, self-sensing bone scaffolds, thermal management coating, and serpentine strain sensors were fabricated. When tested in a direct contact membrane distillation setup, the fabricated membrane demonstrated a promising permeate flux of 21.85 Lm −2 h −1 and a salt rejection of 74.3 %. The fabricated serpentine sensor exhibited stable signal variations under cyclic tensile loading, with a working range of 0–200 % strain and a maximum gauge factor of 43,735. A cell culture test using the printed bone scaffold demonstrated promising cell attachment and proliferation. The DIW printed hBN nanocomposite exhibited reversible shape change under heat, demonstrating potential 4D printing capability and efficient thermal management when exposed to high heat or flame.

Desalination↗
DOE OSTI2025

Tuning gas separation performance of polyimide membranes with macrocyclic crown ether units

Membrane-based gas separation is an energy-efficient alternative to conventional thermally-driven separation processes. However, polymer membranes face the permeability-selectivity trade-off challenge, which stems from the broad size distribution of free volume voids. Here, this study reports a molecular design strategy to address this challenge through incorporating macrocyclic crown ether (CE) moieties into the backbone of Matrimid® polyimide, a commercial gas separation membrane. A series of CE-containing Matrimid®-like copolyimides were synthesized with systematically varied CE molar contents ranging from 3 to 20%. These copolyimides formed ductile, defect-free thin films suitable for membrane fabrication. Gas permeation tests revealed a non-monotonic relationship between permeability/selectivity and CE content. Notably, the copolyimide with only 5% CE demonstrated a 61% increase in CO 2 /CH 4 selectivity and a 13% increase in CO 2 permeability relative to pristine Matrimid®. Higher CE contents did not yield further performance improvements, which is likely due to the competing effects of chain packing disruption and π–π interactions among CE moieties at high content. This hypothesis was supported by wide-angle X-ray scattering (WAXS) analysis, density measurements, and fractional free volume calculations. These findings highlight the potential of macrocyclic crown ether incorporation strategies in fine tuning the microstructure of commercial polyimide gas separation membranes to surpass the traditional permeability-selectivity trade-off.

CO2 separation↗
DOE OSTI2025

Understanding the impact of SPMAK and PEGPEA in crosslinked PEGDA membranes: Methanol-carboxylate co-transport behavior and correlating structure-physicochemical-transport properties

Investigating multicomponent transport in dense, hydrated polymer membranes is necessary in applications such as fuel cells, electrolyzers, and desalination systems. Of particular interest are photoelectrochemical CO 2 reduction cells (PEC-CRC) which produce liquid products such as alcohols (methanol) and carboxylates (formate, acetate). Flux coupling and competitive sorption behavior of these products (solutes) have been found to affect permselectivity, thereby motivating us to investigate fundamental membrane structure-physicochemical-transport relationships. Past research has shown that systematic tuning of crosslinked cation exchange membranes (CEMs) with charge-neutral monoacrylate monomers containing alkyl and phenyl groups (i.e., poly(ethylene glycol) methacrylate (PEGMA), and poly(ethylene glycol) phenyl ether acrylate (PEGPEA)) can suppress acetate transport (permeability) in co-permeation with methanol. To further investigate this transport behavior and to enhance membrane ionic conductivities, 3-sulfopropyl methacrylate potassium (SPMAK), a sulfonated monoacrylate monomer is incorporated here. SPMAK content is varied with neutral PEGPEA and diacrylate crosslinker, poly (ethylene glycol) diacrylate (PEGDA) of two different chain lengths (n = 10 and 13) to prepare membranes of various compositions. Electrochemical and physicochemical properties including ionic conductivity, ion exchange capacity, and water uptake increase with increasing charged SPMAK content. Different states of water within hydrated membranes are probed using differential scanning calorimetry (DSC), where increasing intermediate (loosely bound) water is observed with increasing hydrophilic SPMAK content. The transport behavior of methanol and carboxylates (formate, acetate, propionate) are investigated, where permeabilities vary as methanol > formate > acetate ≈ propionate. Interestingly, permeabilities decrease with increasing PEGPEA content and are more dependent on solute diffusion than sorption. Permeabilities and diffusivities decrease while permselectivities increase with decreasing PEGDA chain length.

25 ENERGY STORAGE↗
DOE OSTI2024

Developing a new ethylene glycol/H 2 O pretreatment system to achieve efficient enzymatic hydrolysis of sugarcane bagasse cellulose and recover highly active lignin: Countercurrent extraction

Improving pretreatment efficiency is a critical premise in achieving efficient biomass conversion, and obtaining high-performance natural polymers is the guarantee of high-value conversion of biomass. Here, in this study, a new pilot-scale continuous countercurrent pretreatment reaction unit about ethylene glycol-alkali solution was designed for pretreating sugarcane bagasse in order to achieve efficient separation of the three major components of lignocellulose when expanding the scale of pretreatment, reduce lignin deposition on the fiber surface, and obtain highly active lignin and excellent enzymatic hydrolysis efficiency of cellulose. X-ray diffractometer (XRD), X-ray photoelectron spectrometer (XPS), brunauer-emmett-teller (BET) and scanning electron microscope (SEM) methods are used to analyze the structural properties of sugarcane bagasse before and after pretreatment, and high-performance liquid chromatography (HPLC) is used to analyze the monosaccharide components in the enzymatic solution. In addition, the structural properties of the recovered lignin are analyzed by gel permeation chromatography (GPC), 31 P NMR and 2D-HSQC-NMR methods. The results indicate that the system can gain a high cellulose recovery of 92.99% along with a lignin removal of 95.33%, and recovered lignin has low lignin carbohydrate complexes, low condensation, and rich in phenolic hydroxyl groups for 1.95 mmol/g. Meanwhile, the countercurrent pretreatment system can effectively reduce the deposition of lignin on the cellulose surface, which is evidently superior to the non-countercurrent pretreatment and facilitates the efficiency of enzymatic saccharification of substrate, achieving a high glucose yield of 99% as well as a total sugar yield of 91.11%. The method efficiently separates biomass in a green manner, and solid residues are easily hydrolyzed, showing potential for industrial-scale production.

09 BIOMASS FUELS↗
DOE OSTI2025

Solvent Transport in Disordered and Dynamic Membrane Pores: Implications for Reverse Osmosis and Nanofiltration Membranes

Pressure-driven separations with nanoporous membranes, such as reverse osmosis and nanofiltration, play a vital role in addressing water scarcity and enabling resource recovery. Understanding water or solvent transport in membrane pores is essential for advancing membrane separation technologies. A key question in transport modeling is to establish a relationship between solvent permeability and membrane porous structure properties, such as porosity or pore size. The nano- and subnanometer pores in polymeric membranes such as reverse osmosis and nanofiltration membranes are highly tortuous and dynamically connected, which challenges the conventional methods of transport modeling. This study addresses this challenge by developing a theoretical framework to describe solvent transport through membranes with dynamic and disordered porous structure. Specifically, we propose a lattice model to describe the pore network, while preserving the viscous nature of solvent permeation. We further establish a relationship between solvent permeability and membrane porosity or pore size, which is validated by molecular dynamics simulations and experimental data. By integrating this relationship into the solution-friction model, we define pore connectivity and local friction coefficient to quantify the impact of pore structure on solvent permeability. Our analysis highlights the dominant influence of pore connectivity on the permeability of reverse osmosis and nanofiltration membranes, particularly when the pore size approaches the dimensions of solvent molecules. Overall, this study provides critical insights into water and solvent transport mechanisms in nanoporous membranes, opening the door for strategies to substantially enhance membrane performance.

membranes↗
DOE OSTI2026

Modeling Flow and Mass Transfer within Hollow Fiber Packaging for Gas Separation

Hollow fiber membrane modules are used for gas purification by their selective permeation properties. Intensification of the process to minimize the retentate loss and gas pressure involves optimization at various scales. In this work, we outline a numerical investigation of the gas separation performance at the scale of fiber bundles and its impact on module performance. Flow channeling and anisotropy govern the mass-transfer coefficient in axial and cross-flow configurations. These effects are quantified in terms of a permeability tensor or an anisotropy ratio and the effective mass-transfer coefficient or the Sherwood number. The results show a trade-off between purification and recovery. While smaller fibers offer a large specific surface area to enable high purification, it comes at a huge penalty on the separation performance due to reduced penetration within bundles. Optimum performance indicators are emphasized.

Fibers↗
DOE OSTI2026

Molecular Modeling of Surfactant Interaction on Phospholipid Bilayers Mimicking Corneal Epithelium

Surfactants found in consumer products can compromise eye corneal membrane integrity upon accidental exposure. Traditional in vitro and in vivo approaches to evaluate membrane–surfactant interaction pose experimental limitations such as species variability, reproducibility, and most often do not provide the overall picture. These limitations motivate the use of in silico models to study phenomena like cellular disruption assays caused by surfactants at the molecular scale. In this work, coarse-grained molecular dynamics simulations have been employed to investigate how nonionic alcohol ethoxylate (AE) and anionic surfactant alcohol ethoxy sulfate (AES) interact with lipid bilayer liposomes that mimic corneal epithelial cell membranes. The spherical liposome is composed of 1,2-dihexadecanoyl-sn-glycero-3-phosphocholine (DPPC), 1,2-di(9Z-octadecenoyl)-sn-glycero-3-phosphoethanolamine (DOPE), 1,2-di(9Z-octadecenoyl)-sn-glycero-3-phospho-l-serine (DOPS), and cholesterol, resembling the composition of the corneal epithelial cells’ membrane bilayer. The simulation consisted of varying degrees of representative surfactant compositions and two initial types of surfactant configurations within or outside the liposome. Our results reveal that both surfactants induce outer leaflet bulging, agreeing with membrane solubilization models. The more highly ethoxylated surfactant, AE, caused more consistent inner leaflet disruption than AES, resulting in significantly more water permeation and membrane thinning. In addition, both surfactants increase the lateral diffusion of lipids within the membrane layers, with higher ethoxylated AE showing a stronger effect than AES. This study demonstrates how surfactant structure and localization influence bilayer membrane integrity, offering mechanistic insights into the irritation potential, thus guiding the rational design of effective surfactant-based formulations.

Lipids↗
DOE OSTI2025

Impact of Ligands on the Ion–Ion Selectivity of Ligand-Appended-Pillar[ n ]arene Channels

Ligand-appended pillar[5]arene (LAP) channels are emerging as a promising platform for ion-selective membranes. In this study, we investigated the ion selectivities of three LAP channels functionalized with distinct ligands: diglycolamine, carbamoylmethyl phosphine oxide, and propionamide phosphonic acid. These ligands were chosen based on their demonstrated affinities for lanthanides in solvent extraction studies. We examined the selectivity of each channel toward a series of monovalent, divalent, and trivalent ions: Li + , Na + , K + , Mg 2+ , Ca 2+ , La 3+ , Eu 3+ , and Yb 3+ . To quantify ion-channel interactions and the energetics of translocation, we computed the potential of mean force (PMF) profiles for each ion. These PMFs were subsequently recast into permeability coefficients, enabling a direct evaluation of ion permselectivity. Our results reveal distinct selectivity patterns governed by the chemical nature of the appended ligands. The diglycolamine-functionalized channel exhibits strong interactions with monovalent ions, leading to replication of the Li + bulk hydration shell within the channel. This promotes preferential transport Li + ions while effectively excluding divalent and trivalent species. In contrast, the carbamoylmethyl phosphine oxide-functionalized channel displays a reduced selectivity between monovalent ions while similarly exhibiting an effective rejection of divalent and trivalent ions. This arises from steric hindrance around channel-lining oxygens imposed by the ligand's bulky phenyl groups which limits heavy ion coordination and promotes retention of hydration shells effectively increasing effective ion size. The propionamide phosphonic acid-functionalized channel exhibits a different trend, favoring ions with lower hydration free energies, with K + ions showing enhanced permeation. These findings highlight the critical role of ligand-ion interactions in modulating ion selectivity within LAP channels. In particular, the strong coordination exhibited by diglycolamine and propionamide phosphonic acid ligands significantly influences the ion transport energetics and selectivity profiles.

hydration↗
DOE OSTI2025

Molecular Modeling and Molecular Dynamics Simulation of a Packed and Intact Bacterial Microcompartment

Bacterial microcompartments (BMCs) are protein-bound organelles found in some bacteria which encapsulate enzymes for enhanced catalytic activity. These compartments spatially sequester enzymes within semipermeable shell proteins and are packed full of enzyme cargoes and metabolites as they fulfill their function. Coupling together recent SAXS and proteomics work, it is possible to develop molecular models for these microcompartments and interrogate enzyme and metabolite dynamics within. Our primary goal of this study is to quantify the permeability of metabolite glyceraldehyde-3-phosphate (G3P) and dihydroxyacetone phosphate (DHAP) across the BMC shell through classical molecular dynamics simulation. The Haliangium ochraceum model of BMC shell (PDB: 6MZX) was used to model an intact BMC of approximately 10 million atoms. Working at this scale presented its own challenges in managing large data sets, with multiple challenges and hardware advances discussed that facilitated this work. Over approximately 750 ns of aggregate simulation, we see multiple permeation events for these metabolites that were added at high concentration through the pores present within BMC shell tiles. When compared to independent permeability estimates for the same metabolites determined through replica exchange umbrella sampling simulations, the permeabilities varied by approximately 3 orders of magnitude. Regardless, the permeability coefficients for both G3P and DHAP are highly similar and very high, such that only very small concentration gradients can be maintained across the BMC shell between the cytosol and BMC interior. The large simulation systems also facilitated comparisons for molecular diffusivity in the crowded environment within the BMC shell. By our estimates, the viscosity within a packed BMC shell is at least 10-fold higher than it would be in neat solution and is the real driver for varying permeability estimates we obtained through simulation. These findings will be used as design inputs for future bioengineering efforts to make products from BMCs, highlighting how permeable BMC shells can be.

Diffusion↗
DOE OSTI2026

Sculpting 2D Crystals via Membrane Contractions before and during Solidification

When phospholipids crystallize within the otherwise fluid membranes of giant unilamellar vesicles, the resulting molecularly thin “2D” solids exhibit great variety in their morphology evolution. For example, within membranes containing moderate amounts of the crystallizing component, crystals grow with a fixed morphology depending on vesicle size. Conversely for membranes containing large amounts of the crystallizing species, we find small compact crystals on vesicles of all sizes. However, on large vesicles, growing crystals sprout flower petals that lengthen progressively. These behaviors result from two combined mechanisms: first, like other 2D solids, the shear rigidity of phospholipid crystals renders them intolerant to morphologies with nonzero Gaussian curvature. As a result and especially at elevated membrane tension, the cost of bending elasticity is reduced at the expense of line energy by the formation of flowers as opposed to compact crystals. Second, the composition-dependent tension rise during cooling relaxes via water permeation of the membrane with a time constant scaling as R2. The amount of crystal formed for a small decrease in temperature determines this composition-dependent increase in stress from thermal contractions versus solidification. Surface Evolver computations were motivated using the predicted tension evolution to develop a processing space that maps to experimental observations for initial and growing crystal morphology. Important variable groups are identified, including a scaled ratio of bending to line energy, a vesicle-size-independent group for membrane contractions, and a time constant for stress relaxation. Though processing stresses ultimately relax, the crystal morphology persists well beyond the processing window.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗