Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRECIPITATION HARDENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

The effect of heat treatment on microfissuring in alloy 718

Changes in the microfissuring susceptibility of alloy 718 due to solution annealing and age hardening are studied. The effects of Ni3Nb (delta) precipitation during solution annealing and gamma-prime + gamma-double-prime precipitation during age hardening on microfissuring are investigated. It is observed that solution annealing reduces microfissuring and age hardening increases it, and the two precipitates do not affect microfissuring susceptibility. Potential causes for the detected intergranular segregation of the alloy are discussed.

Thompson, R. G.↗
NASA NTRSDate not supplied

Effect of Heat Treatments on the Tensile Properties of Additively Manufactured 15-5 Ph Stainless Steel

This study investigated the effect of post-manufacture heat treatments on the microstructure and mechanical properties of 15-5 PH stainless steel (SS) fabricated by laser powder-directed energy deposition (LP-DED). Various heat treatment procedures (CA-H900 and CA-H1150) were conducted to evaluate their effects on the tensile behavior of LP-DED 15-5 PH SS. Scanning electron microscopy was used to characterize the microstructural features and the fracture surfaces. Tensile tests were performed to evaluate the mechanical properties at cryogenic and room temperatures. Reduction in area of CA-H1150 treated specimens after tensile tests was significantly higher than CA-H900 ones, while the ultimate tensile and yield strengths of CA-H900 specimens were higher compared to the CA-H1150 ones. The mechanical behavior of the LP-DED 15-5 PH SS in various heat treatment conditions is discussed based on their microstructures and fracture surfaces.

Laser powder directed energy deposition (LP-DED)↗
NASA NTRS1990

Fracture-tough, corrosion-resistant bearing steels

The fundamental principles allowing design of stainless bearing steels with enhanced toughness and stress corrosion resistance has involved both investigation of basic phenomena in model alloys and evaluation of a prototype bearing steel based on a conceptual design exercise. Progress in model studies has included a scanning Auger microprobe (SAM) study of the kinetics of interfacial segregation of embrittling impurities which compete with the kinetics of alloy carbide precipitation in secondary hardening steels. These results can define minimum allowable carbide precipitation rates and/or maximum allowable free impurity contents in these ultrahigh strength steels. Characterization of the prototype bearing steel designed to combine precipitated austenite transformation toughening with secondary hardening shows good agreement between predicted and observed solution treatment response including the nature of the high temperature carbides. An approximate equilibrium constraint applied in the preliminary design calculations to maintain a high martensitic temperature proved inadequate, and the solution treated alloy remained fully austenitic down to liquid nitrogen temperature rather than transforming above 200 C. The alloy can be martensitically transformed by cryogenic deformation, and material so processed will be studied further to test predicted carbide and austenite precipitation behavior. A mechanistically-based martensitic kinetic model was developed and parameters are being evaluated from available kinetic data to allow precise control of martensitic temperatures of high alloy steels in future designs. Preliminary calculations incorporating the prototype stability results suggest that the transformation-toughened secondary-hardening martensitic-stainless design concept is still viable, but may require lowering Cr content to 9 wt. pct. and adding 0.5 to 1.0 wt. pct. Al. An alternative design approach based on strain-induced martensitic transformation during cryogenic forming, thus removing the high martensitic constraint, may permit alloy compositions offering higher fracture roughness.

Olson, Gregory B.↗
NASA NTRS1994

On massive carbide precipitation during high temperature low cycle fatigue in alloy 800H

The effect of strain rate on massive precipitation and the mechanism for the occurrence of massive precipitation of M23C6 in alloy 800H is investigated during elevated temperature low cycle fatigue testing. It was observed that large M23C6 platelets were in the vicinity of grain and incoherent twin boundaries. The strain controlled fatigue testing at higher strain rates that promoted cyclic hardening enabled massive precipitation to occur more easily.

CARBON SUPERSATURATION↗
NASA NTRS1972

Effect of metallurgical structure and properties on adhesion and friction behavior of cobalt alloys

The metallurgical structure and some of the mechanical properties of two cobalt alloys, cobalt-50% iron and cobalt-25% molybdenum-10% chromium, were determined under various heat treated conditions. The mechanical properties of the bcc disordered Co-50Fe alloy, which was found to be very brittle, indicated an exceedingly low fracture strength, low hardness, and very weak grain boundary strength. Ordering by suitable heat treatment only produced a more brittle material with a lower fracture strength and a slightly higher hardness value. Work hardening was found to produce a finer grain structure and a greater grain boundary strength. Tensile properties were examined. It was found that the Co-25Mo-10Cr alloy was difficult to place in the alpha Co solid solution condition, which limited the ability to use precipitation as a hardening reaction. Over two hundred adhesion cycles from zero contact load, to maximum load, to fracture were conducted between couples for each of the above alloys in an ultrahigh vacuum system which would permit the sample surfaces to be cleaned of all contaminant layers. In the Co-50Fe case, the calculated fracture stress from the adhesion tests showed values in the range of 80 to 150 k.s.i., which is about ten times greater than the values from tension tests.

Keller, D. V., Jr.↗
NASA NTRS1999

1300 K Creep Behavior of [001] Oriented Ni-49Al-1Hf (at.%) Single Crystals

A study of the 1300 K compressive and tensile creep properties of [001]-oriented NiAl-1Hf (D209) single crystals has been undertaken. Neither post homogenization cooling treatment, minor chemical variations within an ingot or from ingot-to-ingot, nor testing procedure had a significant effect on mechanical behavior; however a heat treatment which dissolved the initial G-phase precipitates and promoted formation of Heusler particles led to a strength reduction. Little primary creep was found utilizing direct measurement of strain, and a misorientation of 18 deg from the [001] did not reduce the creep strength. The effects of heat treatments on properties and a comparison of the flow stress-strain rate data to those predicted by the Jaswon-Cottrell solid solution hardening model indicate that the 1300 K strength in NiAl-1Hf single crystals is mainly due to precipitation hardening mechanisms.

Whittenberger, J. Daniel↗
NASA NTRS1976

Phase transformation and stabilization of a high strength austenite

An investigation of the phase transformation and the austenite stabilization in a high strength austenite has been made. An Fe-29Ni-4.3Ti austenite age-hardened by gamma-prime (Ni3Ti) precipitates showed a further increase of strength after martensitic and reverse martensitic phase transformations. The stability of ausaged austenite as well as ausaged and transformation-strengthened austenite was improved significantly through an isothermal treatment at 500 C. The Ms temperature of the strengthened austenite was restored to nearly that of annealed austenite while the austenite was hardened to R(C) 41 through precipitation and phase transformations. The observed austenite stabilization is attributed to the formation of GP zones or short-range order of less than about 10A in size.

Jin, S.↗
NASA NTRS1990

Inelastic deformation under nonisothermal loading

The objective of this paper is to evaluate, both experimentally and analytically, the appropriate forms of the hardening evolution equations in unified constitutive models for conditions involving nonisothermal loading. Critical experiments were performed for a cast nickel-base superalloy by using variable temperature tensile, creep, and cyclic tests in the 538-982 C temperature range. These experimental results were compared with both isothermal data and predictions of the Bodner-Partom-Bodner, 1987 elastic-viscoplastic theory to assess the effects of thermal history on constitutive behavior. The results indicate that the hardening evolution equations based on isothermal data are applicable for nonisothermal loading of these precipitation strengthened alloys. Additional thermal history effect terms in the hardening evolution equations were not required beyond those accounting for the variation of material constants with temperature. Using material constants determined solely from isothermal data, the inelastic deformation behavior of B1900 + Hf subject to thermomechanical loading were adequately predicted by the Bodner-Partom model.

Chan, K. S.↗
NASA NTRS1992

Hardening mechanisms in a dynamic strain aging alloy, Hastelloy X, during isothermal and thermomechanical cyclic deformation

The relative contributions of the hardening mechanisms in Hastelloy X during cyclic deformation were investigated by conducting isothermal cyclic deformation tests within a total strain range of +/-0.3 pct and at several temperatures and strain rates, and thermomechanical tests within several different temperature limits. The results of the TEM examinations and special constant structure tests showed that the precipitation on dislocations of Cr23C6 contributed to hardening, but only after sufficient time above 500 C. Solute drag alone produced very considerable cyclic hardening. Heat dislocation densities, peaking around 10 exp 11 per sq cm, were found to develop at temperatures producing the greatest cyclic hardening.

Miner, R. V.↗
NASA NTRS1972

Study of X-ray diffraction on aging alloys with different degrees of volume discrepancy between the precipitation phase and the matrix

Study of the diffraction patterns of X rays diffracted by dispersion-hardened alloys with various degrees of difference between the specific atomic volumes of their precipitation phases and matrices. Experiments were performed on aging alloys KhN77TIuR (nimonic) and KhN67VMTIuO, which have the same types of gamma solid solutions and precipitating gamma prime phases, but differ considerably with respect to the volume factor. It is found that in the decay of supersaturated solid solutions for which the difference between the specific atomic volumes of the precipitation phase and the matrix is small (alloy KhN67VMTIuO) the nature of the intensity distribution of the diffraction lines remains practically unchanged regardless of the aging, while in cases where the volume discrepancy is large (alloy KhN77TIuR) significant changes in the appearance of the diffraction lines are recorded.-

Gitgarts, M. I.↗
NASA NTRS1991

NiAl alloys for structural uses

Alloys based on the intermetallic compound NiAl are of technological interest as high temperature structural alloys. These alloys possess a relatively low density, high melting temperature, good thermal conductivity, and (usually) good oxidation resistance. However, NiAl and NiAl-base alloys suffer from poor fracture resistance at low temperatures as well as inadequate creep strength at elevated temperatures. This research program explored macroalloying additions to NiAl-base alloys in order to identify possible alloying and processing routes which promote both low temperature fracture toughness and high temperature strength. Initial results from the study examined the additions of Fe, Co, and Hf on the microstructure, deformation, and fracture resistance of NiAl-based alloys. Of significance were the observations that the presence of the gamma-prime phase, based on Ni3Al, could enhance the fracture resistance if the gamma-prime were present as a continuous grain boundary film or 'necklace'; and the Ni-35Al-20Fe alloy was ductile in ribbon form despite a microstructure consisting solely of the B2 beta phase based on NiAl. The ductility inherent in the Ni-35Al-20Fe alloy was explored further in subsequent studies. Those results confirm the presence of ductility in the Ni-35Al-20Fe alloy after rapid cooling from 750 - 1000 C. However exposure at 550 C caused embrittlement; this was associated with an age-hardening reaction caused by the formation of Fe-rich precipitates. In contrast, to the Ni-35Al-20Fe alloy, exploratory research indicated that compositions in the range of Ni-35Al-12Fe retain the ordered B2 structure of NiAl, are ductile, and do not age-harden or embrittle after thermal exposure. Thus, our recent efforts have focused on the behavior of the Ni-35Al-12Fe alloy. A second parallel effort initiated in this program was to use an alternate processing technique, mechanical alloying, to improve the properties of NiAl-alloys. Mechanical alloying in the conventional sense requires ductile powder particles which, through a cold welding and fracture process, can be dispersion strengthened by submicron-sized oxide particles. Using both the Ni-35Al-Fe alloys to contain approx. 1 v/o Y2O3. Preliminary results indicate that mechanically alloyed and extruded NiAl-Fe + Y2O3 alloys when heat treated to a grain-coarsened condition, exhibit improved creep resistance at 1000 C when compared to NiAl; oxidation resistance comparable to NiAl; and fracture toughness values a factor of three better than NiAl. As a result of the research initiated on this NASA program, a subsequent project with support from Inco Alloys International is underway.

Koss, D. A.↗
NASA NTRS1989

The low cycle fatigue deformation response of a single-crystal superalloy at 650 C

The cyclic stress-strain response and the associated deformation structure of the single crystal nickel-base superalloy PWA 1480 were investigated. Specimens of various crystallographic orientations were tested in low-cycle fatigue (LCF) at 650 C, resulting in a significant tension-compression anisotropy in initial yield strength associated with the shearing of gamma-prime precipitates by dislocation pairs, and a LCF cyclic hardening of the crystals associated with dislocation interactions occurring in the gamma phase. In specimens deforming by slip on a single slip system, dislocations of the primary slip system accumulated in the gamma matrix and formed seesile entanglements. In specimens deforming by slip on several slip systems, the dislocations of the different operative slip systems intersected in the gamma matrix and formed sessile arrangements.

Gabb, T. P.↗
NASA NTRS1988

The Cyclic Stress-Strain Behavior of a Single Crystal Nickel-Base Superalloy

The cyclic stress-strain response and similar deformation structures of the single crystal nickel based superalloy was described under a specific set of conditions. The isothermal low cycle fatigue response and deformation structures were described at a typical intermediate temperature and at high temperature. Specimens oriented near the (001) and (111) crystallographic orientations were tested at 1050 C, where more moderate orientation effects were expected. This enabled the description of the deformation structures at each of the 2 temperatures and their relationship to the observed cyclic stress-strain behavior. The initial yield strength of all specimens tested at 650 C was controlled by the shearing of the gamma prime precipitates by dislocation pairs. Low cycle fatigue tests at 650 C had cyclic hardening, which was associated with dislocation interactions in the gamma matrix. The initial yield strength of specimens tested at 1050 C was associated with dislocation bypassing of the gamma prime precipitates. Low cycle fatigue tests at 1050 C had cyclic softening, associated with extensive dislocation recovery at the gamma-gamma prime interfaces along with some gamma prime precipitate coarsening.

Gabb, Timothy P.↗
NASA NTRS2007

Sequestration of Single-Walled Carbon Nanotubes in a Polymer

Sequestration of single-walled carbon nanotubes (SWCNs) in a suitably chosen polymer is under investigation as a means of promoting the dissolution of the nanotubes into epoxies. The purpose of this investigation is to make it possible to utilize SWCNs as the reinforcing fibers in strong, lightweight epoxy-matrix/carbon-fiber composite materials. SWCNs are especially attractive for use as reinforcing fibers because of their stiffness and strength-to-weight ratio: Their Young s modulus has been calculated to be 1.2 TPa, their strength has been calculated to be as much as 100 times that of steel, and their mass density is only one-sixth that of steel. Bare SWCNs cannot be incorporated directly into composite materials of the types envisioned because they are not soluble in epoxies. Heretofore, SWCNS have been rendered soluble by chemically attaching various molecular chains to them, but such chemical attachments compromise their structural integrity. In the method now under investigation, carbon nanotubes are sequestered in molecules of poly(m-phenylenevinylene-co-2,5-dioctyloxy-p-phenylenevinylene) [PmPV]. The strength of the carbon nanotubes is preserved because they are not chemically bonded to the PmPV. This method exploits the tendency of PmPV molecules to wrap themselves around carbon nanotubes: the wrapping occurs partly because there exists a favorable interface between the conjugated face of a nanotube and the conjugated backbone of the polymer and partly because of the helical molecular structure of PmPV. The constituents attached to the polymer backbones (the side chains) render the PmPV-wrapped carbon nanotubes PmPV soluble in organic materials that, in turn, could be used to suspend the carbon nanotubes in epoxy precursors. At present, this method is being optimized: The side chains on the currently available form of PmPV are very nonpolar and unable to react with the epoxy resins and/or hardeners; as a consequence, SWCN/PmPV composites have been observed to precipitate out of epoxies while the epoxies were being cured. If the side chains of the PmPV molecules were functionalized to make them capable of reacting with the epoxy matrices, it might be possible to make progress toward practical applications. By bonding the side chains of the PmPV molecules to an epoxy matrix, one would form an PmPV conduit between the epoxy matrix and the carbon nanotubes sequestered in the PmPV. This conduit would transfer stresses from the epoxy matrix to the nanotubes. This proposed load-transfer mode is similar to that of the current practice in which silane groups are chemically bonded to both the epoxy matrices and the fibers (often glass fibers) in epoxymatrix/fiber composites.

Bley, Richard A.↗
NASA NTRS1976

The morphology of energetic O/+/ ions during two magnetic storms - Latitudinal variations

Results are presented for a statistical analysis of the latitudinal variations of precipitating O(+) and H(+) ions with energies between 0.7 and 12 keV during the magnetic storms of Dec. 16 and 17, 1971. Particular attention is given to some typical characteristics of the O(+) energy spectra along with an intercomparison of the O(+) and H(+) average energies during each storm. Major findings are that (1) the O(+) energy spectra were quite structured, one or more peaks being frequently observed; (2) the O(+) energy spectra which were still rising at 12 keV were not uncommon, especially at high latitudes; and (3) a significant hardening of the O(+) spectrum with increasing latitude was observed at the higher latitudes during the December 17 storm, along with a significant hardening with decreasing latitude at the low-latitude edge of the precipitation zone on the night side. A statistically significant difference in average energies between the two ionic species was revealed.

Sharp, R. D.↗
NASA NTRS2020

Microstructure and Hardness of 57Ni –40Ti –3Hf (wt.%)

Ni-rich NiTiHf (57 wt.% Ni – 40 wt.% Ti – 3 wt.% Hf) is an intermetallic material that is superelastic, corrosion resistant and hardenable through relatively simple heat treatment procedures. The composition, microstructure and hardness of two separate lots of Ni-rich NiTiHf were investigated. The measured compositions for both lots were nominal, with total impurities in each of less than 0.01 wt%. The average grain sizes were 28.0µm and 26.4µm for the two lots. In its annealed condition (1,050°C × 48h/furnace cool to room temperature), the microstructure consisted of a B2 (cubic) NiTiHf parent phase with abundant Ni4Ti3 precipitates and a few TiC inclusions. The grain boundaries were decorated with HfO2 particles and metastable Ni3Ti2 precipitates that were cubic in structure. The average hardness varied from approximately 470HV to 490HV for the two lots. The hardened (annealed then 900°C × 2h/water quench to room temperature) microstructure consisted of a B2 NiTiHf parent phase with no precipitates, HfO2 decorating the grain boundaries and some TiC inclusions. The average hardness in this heat treatment condition was approximately 580HV for both lots. The aged (hardened then 400°C × 30min/water quench to room temperature) microstructure consisted of a B2 NiTiHf parent phase containing a high density of very fine Ni4Ti3 precipitate phase, HfO2 decorating the grain boundaries and some TiC inclusions. For each lot, the average hardness decreased slightly after aging as compared to the hardened heat treatment condition. This report is expected to serve as a reference for a forthcoming Materials Specification for the use of Ni-rich NiTiHf in flight hardware.

intermetallics, compositional analysis, Vickers ha↗
NASA NTRS1992

Creep deformation of B2 aluminides

The creep resistance and elevated temperature deformation mechanisms in CoAl, FeAl, and NiAl are reviewed. The stress and temperature dependencies of the steady state creep rate, the primary creep behavior, the dislocation substructure, and the response during transient tests are used as the main indicators of the deformation processes. In single phase intermetallics, the influence of grain size, stoichiometry, and solid solution hardening have been examined. In addition, the effect of adding dispersoids, precipitates, and other types of reinforcements to improve creep strength are compared.

Nathal, M. V.↗