Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PORE PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Periodicity Analysis of Earthquake Occurrence and Hypocenter Depth Near Parkfield, California, 1994–2002 Versus 2006–2014

In central California, periodic earthquake occurrence suggests a relationship with annual hydrological, atmospheric, thermal, and tidal loadings. Here, in catalogs of declustered earthquakes within 100 km from Parkfield, CA, we study a semiannual periodicity for the monthly number of ≤7.2-km-deep earthquakes and the monthly median hypocenter depth over 1994–2002 and 2006–2014. Peak-trough months in fitted periodic components differ between time spans and event populations. Deeper earthquakes present no semiannual and a weak annual periodicity. Although modeled pore pressure shows a Spring peak, when added to the elastic Coulomb stress from surface hydrospheric loads, it fails to predict a 6-month periodicity for 2006–2014. In 1994–2002, the pore-pressure amplitude appears to be of same order as the elastic stress and may have had a stronger effect. In 2006–2014, we did not find load model parameters explaining the observed pattern or apparent changes following the 2003 San Simeon and 2004 Parkfield earthquakes.

58 GEOSCIENCES↗

En echelon faults reactivated by wastewater disposal near Musreau Lake, Alberta

We use machine-learning and cross-correlation techniques to enhance earthquake detectability by two magnitude units for the earthquake sequence near Musreau Lake, Alberta, which is induced by wastewater disposal. This deep catalogue reveals a series of en echelon ~N–S oriented strike-slip faults that are favourably oriented for reactivation. These faults require only ~0.6 MPa overpressure for triggering to occur. Earthquake activity occurs in bursts, or episodes; episodes restricted to the largest fault tend to have earthquakes starting near the southern end (distant from injectors) and progressing northwards (towards the injectors). While most events are concentrated along these ~N–S oriented faults, we also delineate smaller faults. Together, these findings suggest pore pressure as the triggering mechanism, where a time-dependent increase in pore pressure likely caused these faults to progressively reawaken. Analysis of the ‘next record-breaking event’, a statistical model that forecasts the sequencing of earthquake magnitudes, suggests that the next largest event would be M L ~4.3. The seismically illuminated length of the largest fault indicates potential magnitudes as large as M w 5.3.

58 GEOSCIENCES↗

Mechanical Response of Castlegate Sandstone under Hydrostatic Cyclic Loading

The stress history of rocks in the subsurface affects their mechanical and petrophysical properties. Rocks can often experience repeated cycles of loading and unloading due to fluid pressure fluctuations, which will lead to different mechanical behavior from static conditions. This is of importance for several geophysical and industrial applications, for example, wastewater injection and reservoir storage wells, which generate repeated stress perturbations. Laboratory experiments were conducted with Castlegate sandstone to observe the effects of different cyclic pressure loading conditions on a common reservoir analogue. Each sample was hydrostatically loaded in a triaxial cell to a low effective confining pressure, and either pore pressure or confining pressure was cycled at different rates over the course of a few weeks. Fluid permeability was measured during initial loading and periodically between stress cycles. Samples that undergo cyclic loading experience significantly more inelastic (nonrecoverable) strain compared to samples tested without cyclic hydrostatic loading. Permeability decreases rapidly for all tests during the first few days of testing, but the decrease and variability of permeability after this depend upon the loading conditions of each test. Cycling conditions do affect the mechanical behavior; the elastic moduli decrease with the increasing loading rate and stress cycling. The degree of volumetric strain induced by stress cycles is the major control on permeability change in the sandstones, with less compaction leading to more variation from measurement to measurement. The data indicate that cyclic loading degrades permeability and porosity more than static conditions over a similar period, but the petrophysical properties are dictated more by the hydrostatic loading rate rather than the total length of time stress cycling is imposed.

58 GEOSCIENCES↗

Assessment of Brine Management for Geologic Carbon Sequestration

Geologic carbon sequestration (GCS) is the injection of carbon dioxide (CO 2 ), typically captured from stationary emission sources, into deep geologic formations to prevent its entry into the atmosphere. Active pilot facilities run by regional United States (US) carbon sequestration partnerships inject on the order of one million metric tonnes (mt) CO 2 annually while the US electric power sector emits over 2000 million mt-CO 2 annually. GCS is likely to play an increasing role in US carbon mitigation initiatives, but scaling up GCS poses several challenges. Injecting CO 2 into sedimentary basins raises fluid pressure in the pore space, which is typically already occupied by naturally occurring, or native, brine. The resulting elevated pore pressures increase the likelihood of induced seismicity, of brine or CO 2 escaping into potable groundwater resources, and of CO 2 escaping into the atmosphere. Brine extraction is one method for pressure management, in which brine in the injection formation is brought to the surface through extraction wells. Removal of the brine makes room for the CO 2 and decreases pressurization. Although the technology required for brine extraction is mature, this form of pressure management will only be applicable if there are cost-­effective and sustainable methods of disposing of the extracted brine. Brine extraction, treatment, and disposal may increase the already substantial capital, energy, and water demands of Carbon dioxide Capture and Sequestration (CCS). But, regionally specific brine management strategies may be able to treat the extracted water as a source of revenue, energy, and water to subsidize CCS costs, while minimizing environmental impacts. By this approach, value from the extracted water would be recovered before disposing of any resulting byproducts. Until a price is placed on carbon, we expect that utilities and other CO 2 sources will be reluctant to invest in capital intensive, high risk GCS projects; early technical, economic, and environmental assessments of brine management are extremely valuable for determining the potential role of GCS in the US. We performed a first order feasibility and economic assessment, at three different locations in the US, of twelve GCS extracted-­water management options, including: geothermal energy extraction, desalination, salt and mineral harvesting, rare-­earth element harvesting, aquaculture, algae biodiesel production, road de-­icing, enhanced geothermal system (EGS) recharge, underground reinjection, landfill disposal, ocean disposal, and evaporation pond disposal. Three saline aquifers from different regions of the US were selected as hypothetical GCS project sites to encompass variation in parameters that are relevant to the feasibility and economics of brine disposal. The three aquifers are the southern Mt. Simon Sandstone Formation in the Illinois Basin, IL; the Vedder Formation in the southern San Joaquin Basin, CA; and the Jasper Interval in the eastern Texas Gulf Basin, TX. These aquifers are candidates for GCS due to their physical characteristics and their close proximity to large CO 2 emission sources. Feasibility and impacts were calculated using one mt-­CO 2 injected as the functional unit of brine management. Scenarios were performed for typical 1000MW coal-­fired power plants (CFPP) that incurred an assumed 24 percent carbon capture energy penalty (EP), injected 90 percent of CO 2 emissions (~9 million mt-­ CO 2 injected annually), and treated extracted water onsite. Net present value (NPV), land requirements, laws and regulations, and technological limits were determined for each stage of disposal, and used to estimate feasibility. The boundary of the assessment began once extracted water was brought to the surface, and ended once the water evaporated, was injected underground, or was discharged into surface water bodies. Results of the assessment were generated, stored, and analyzed using Microsoft Excel spreadsheets and ESRI Geographical Information System (GIS) maps. Conclusions about the relative benefits and impacts of alternative brine-­management strategies were highly sensitive to local climate and weather, and aquifer water chemistry. The NPV of certain scenarios ranged from -­$50/mt-­CO 2 (a cost) to +$10/mt-­CO 2 (revenue). The land footprint of the scenarios in this study ranged from <1 km 2 to 100 km 2 . Brine extraction as a pressure management tool for GCS has potential for improving the economics and for minimizing the environmental impacts of CCS. In order to maximize this potential, careful analysis of each saline aquifer and region must be conducted to determine a regionally appropriate brine use sequence (BUS) at the time of site selection. Models that use GIS will be essential tools in determining such sequences for individual CFPP. Future studies that perform risk and life cycle assessments (LCA) of BUS scenarios, incorporate additional impact metrics into the BUS model, and enhance the temporal sensitivity of the model would improve the robustness of this regional assessment method.

54 ENVIRONMENTAL SCIENCES↗

Assessing the geomechanical stability of interbedded hydrate-bearing sediments under gas production by depressurization at NGHP-02 Site 16

Establishing the geomechanical stability of marine sediments in the vicinity of a production well is one of the key design considerations in planning offshore gas production from marine hydrate reservoirs. This work presents an assessment of the sediment stability at India's National Gas Hydrate Program, Expedition 2 (NGHP-02) Site 16 Area B offshore eastern India, for which gas production is to be carried out by depressurization. One important feature of the study is that extensive calibration of constitutive model parameters has been conducted based on laboratory test data from pressured core samples. From analysis perspective, the site is challenging because the hydrate reservoir consists of thin layers of hydrate-bearing sands interbedded with mud. Moreover, depressurization at the depth of a reservoir more than 2750 m below sea surface will lead to a pore pressure drop, and accordingly an effective confining stress increase as high as 25 MPa. In dealing with thin interbedded hydrate-bearing strata, meshing requirements for flow and geomechanical analysis are quite different from those for reservoirs with thicker massive layers, An axisymmetric model and one-way coupling simulations were thus adopted for this study, in which the geomechanical study utilizes pore pressure and hydrate saturation output from the flow study, but the flow study does not takes the porosity changes from the geomechanical analysis. Instead, the reduction of porosity due to sediment deformation in the flow study is based on a pressure-dependent pore compressibility relationship derived from geomechanical modeling. The rationality is validated through back computing the pore compressibility from the geomechanical deformation results. Finally, the study shows that large compression in the reservoir will result in movement of the sediments from above and below, as well as laterally in smaller magnitudes; and the sediment is deemed stable during the gas production period.

58 GEOSCIENCES↗

Cement stress and microstructure evolution during curing in semi-rigid high-pressure environments

The process of cement slurry curing into a solid has a direct effect on the initial state of stress in a composite concrete and steel structure. Failure models for critical infrastructure and wellbores could benefit from measurements of this initial stress because it greatly influences structural performance. Here, we present measurements of the initial stress state (total stress, effective stress, and pore pressure) of multiple cement formulations cured under a high-pressure of 40 MPa within a semi-rigid steel pipe. Our results show that cements cured in this restrained environment exhibit dense microstructures with low permeability (nano-Darcy), develop an anisotropic stress state greater than zero and less than the curing pressure, and undergo a staged curing process where hydration and mechanical behaviors evolve from a slurry into a pre-stressed porous medium. Both drained and undrained scenarios were investigated, revealing a feedback from the semi-rigid boundary towards improved cement performance.

36 MATERIALS SCIENCE↗

Submarine landslides triggered by destabilization of high-saturation hydrate anomalies: LANDSLIDES CAUSED BY HYDRATE ANOMALIES

Submarine landslides occur along continental margins at depths that often intersect the gas hydrate stability zone, prompting suggestions that slope stability may be affected by perturbations that arise from changes in hydrate stability. Here we develop a numerical model to identify the conditions under which the destabilization of hydrates results in slope failure. Specifically, we focus on high-saturation hydrate anomalies at fine-grained to coarse-grained stratigraphic boundaries that can transmit bridging stresses that decrease the effective stress at sediment contacts and disrupt normal sediment consolidation. We evaluate slope stability before and after hydrate destabilization. Hydrate anomalies act to significantly increase the overall slope stability due to large increases in effective cohesion. However, when hydrate anomalies destabilize there is a loss of cohesion and increase in effective stress that causes the sediment grains to rapidly consolidate and generate pore pressures that can either trigger immediate slope failure or weaken the surrounding sediment until the pore pressure diffuses away. In cases where failure does not occur, the sediment can remain weakened for months. In cases where failure does occur, we quantify landslide dynamics using a rate and state frictional model and find that landslides can display either slow or dynamic (i.e., catastrophic) motion depending on the rate-dependent properties, size of the stress perturbation, and the size of the slip patch relative to a critical nucleation length scale. Our results illustrate the fundamental mechanisms through which the destabilization of gas hydrates can pose a significant geohazard.

58 GEOSCIENCES↗

Sequential Fracture Activation and Stress Evolution During EGS Stimulation at Utah FORGE Revealed by Waveform Cross‐Correlation

Mapping fracture networks in Enhanced Geothermal Systems (EGS) is essential for optimizing reservoir performance, yet complex fracture evolution during stimulation remains difficult to resolve. This study examines the evolution of microseismicity and fracture networks during stage 3 of the 2022 EGS stimulation at the Utah Frontier Observatory for Research in Geothermal Energy site. We map the fracture network represented by 20 clusters of seismic events identified by waveform similarities with cross-correlation. We characterize their geometric properties such as strike, dip, length, and width, and analyze the time evolution of activated fractures. The results reveal a systematic fracture evolution: early activation of pre-existing natural fractures, complex network development during peak injection, and continued activation of less favorably oriented fractures post-injection. Magnitude calibration using the Principal Component Analysis of cross-correlated waveforms improves relative amplitude measurements, refining estimations of the Gutenberg-Richter b-values with spatial variations in b-values suggesting stress re-distribution across the stimulated area. Analysis of the stress state of selected fractures further shows that fractures requiring higher excess pore pressure primarily activate at the end of injection and post-injection, highlighting stress transfer due to pore pressure as a dominant triggering mechanism. These findings provide insights into fracture propagation, stress evolution, and seismic hazard assessment in EGS reservoirs.

Asirifi, Richard [Texas A & M Univ., College Stati↗

A Novel Technique for Distributed Measuring of Strain in the Vadose Zone

Characterizing water content and pressure changes in the vadose zone is important to understanding a variety of geologic processes, ranging from permeability, to evapotranspiration, and aquifer recharge. Changes in water content, or pressure, cause strain in the solid porous medium of the vadose zone, and it is possible that measuring those strains could be used a characterization tool. The Coherence-length-gated Microwave Photonics Interferometry (CMPI) technique measures strain at high resolution along many intervals defined by pairs of reflectors distributed along an optical fiber. This technique has recently been developed at Clemson University, and it has the spatial, and temporal resolution to characterize the strains that are expected to occur with hydrologic changes in the vadose zone. However, the technique has never been used to measure strain in porous media, so its capabilities remain uncertain. The objective of this thesis is to evaluate the ability of using CMPI to measure strain changes in the vadose zone. The research approach consists of conducting laboratory tests using a column filled with sand that was subjected to changes in water content and pressure. An optical fiber with CMPI reflectors was deployed in a high surface area ribbon and used to measure strain along the axis of the column. The column was made from 8-inch, Schedule 40 PVC pipe (75 cm tall, 20 cm inner diameter) and filled with medium-grained sand (K = 2.5x10-6 m/s, porosity = 0.28, Coefficient of Uniformity = 2, van Genuchten (n = 4.34 and  = 0.00039 m-1), Young’s Modulus = 18 – 47 MPa). Five pressure and four temperature sensors attached to probes inserted into the wall. The optical fiber includes five reflectors spaced 10 cm apart on the inside and outside of the column along the vertical axis. Strain measurements are made between pairs of reflectors. The reflectors are created in 250-micron-diameter acrylate-coated single mode Corning SMF28e+ optical fiber using a femtosecond laser. The optical fiber was laminated between two pieces of polyester film creating a large surface area to transfer strain from the porous media to the optical fiber. The experiments were conducted by filling the column from the bottom or infiltrating water from the top. The water was allowed to equilibrate to room temperature prior to each test in order to limit thermoelastic strain. Five injection tests with a rate of 250 ml/min and three infiltration tests at varying rates were conducted, and the results show patterns of strain and pressure are generally similar. Hydrologic conditions define three zones based on the pressure magnitude and distribution. 1.) Ambient Zone where the pressure heads are quasi-static and the pressure gradient is roughly unity (head gradient of zero). This is the uppermost zone and is characterized by negative pressures. 2.) Transition Zone where the pressures increase from ambient to zero, are changing relatively rapidly and the pressure gradient is relatively steep (pressure head gradients of 2). The Transition zone is 10 to 15 cm thick. 3.) Positive Pressure Zone where the pressure is positive, the rate of change is slower than in the transition zone and the gradient is flatter (pressure head gradient 1.1 to 1.2). This is the lowest zone in the column. Injection of water causes the pressure to increase and the three zones to move upward. The Transition zone moves at a rate of approximately 0.0002 m/s +/- .00005, according to analyses of pressure profiles. This is the same as the average velocity of the water calculated as volumetric flux/effective porosity =5.4x10-5 m/s/0.28. Strain signals in the range of 10s  were observed with a noise level of generally less than 0.1  (signal to noise ratio of greater than 100) during injection and drainage. The spatial and temporal distributions of strain caused by injection depend on the location of the moving pressure zones. The locations of the different pressure zones were determined from pressure profiles at different times and these data were transferred to strain time series. This showed that strain in the Ambient pressure zone is either unchanged or slightly compressive, whereas strain in Transition zone is tensile and roughly proportional to the pressure change, and strain ranges from tensile to compressive in the Positive Pressure zone. In general, the strain is variable at the top of the Positive Pressure zone, but it appears to be consistently tensile lower in the zone. The spatial distribution of strain causes three distinct stages in the strain times series measured between pairs of CMPI reflectors. The strain is unchanged or slightly compressive during Stage 1, it increases (positive strain is tensile) approximately linearly at a rate of 0.02 to 0.03 μ/s during the Stage 2, and then flattens out in Stage 3. The strain increases again during Stage 4 of the time series. The pressure also changes in stages. It is unchanged during Stage 1 and then increases relatively rapidly at a rate of between 4 and 10 Pa/s during Stage 2 and continues to increase during Stages 3 and 4, but at a rate slightly slower than during Stage 2 (from 2.5 to 3.5 Pa/s). The rates of pressure and strain change are consistent with basic analyses. The rate of pressurization is similar to the calculated velocity of flow in the saturated zone, and this is similar to the measured velocity of the strain increase. The ratio of the pressurization rate and strain rate during Stage 2 (2.5 (Pa/s) /0.03 (μ/s)) is 80 MPa, which is approximately equal to the upper range expected considering the uniaxial compression and the Young’s Modulus of the sand. An interesting effect occurs when the upper surface of the sand becomes saturated. Significant compression (several 10s of ) occurs as the pressure and saturation increase at the upper surface. Compression occurs throughout the column, but the effect is greatest at the top of the column. The rate of compression is fastest slightly before ponding occurs, but it slows markedly and nearly stops when water starts to accumulate at the surface (ponding). This effect reverses when the surface of the sand is drained, resulting in tension throughout the column. The compression caused by this effect can be as large or larger than the tensile strain that accumulated during filling. This effect was unexpected because increasing pressure is normally associated with tensile strain. Nevertheless, this effect was observed consistently in all tests where the pressure changes at the upper surface, including tests where water was injected from below or infiltrated from above. This effect behaves as if the pore pressure at the upper surface of the sand exerts a normal force on the boundary (increasing pore pressure exerts a downward compression on the boundary). The results of these laboratory experiments indicate that CMPI can measure strain caused by fluid pressure changes in the vadose zone with a signal to noise ratio of 100 or more. Injection and drainage cause a strain signal that is complex, but repeatable. The magnitudes of the strain signal are consistent with magnitudes that are expected based on poroelastic calculations using independently measured properties of the sand. These results indicate that the CMPI technique with an optical fiber laminated in a polyester ribbon generates data that represent the strain distribution during hydrologic processes of imbibition and drainage in variably saturated sand. This suggests that distributed strain measurements using CMPI could be a viable approach for evaluating processes in the vadose zone, laying the groundwork for future field implementation.

47 OTHER INSTRUMENTATION↗

Extensional reactivation of an abandoned thrust - A bound on shallowing in the brittle regime

Shallow dip angles (not greater than 45 deg) suggested by field observations of continental extensional faults are not predicted by classical isotropic Mohr-Coulomb-Anderson theory. Earthquake data indicate that normal faults exist in the upper crust with dip angles commonly as shallow as 30 deg. One explanation of the apparent conflict between theory and structural/seismic observations is that intrinsically weak, shallow-dipping pre-existing faults are preferentially reactivated. An analytical treatment clarifies the roles of geometry, intact/preexisting fault strengths and fluid pore pressures. Frictional strength ratios of 3 or greater could account for extremely shallow normal faults (dips 10-20 deg) without consideration of pore pressures in excess of the least principal stress or of principal stress systems rotated away from the gravity vector. Moderate reduction in friction (3/4) with respect to wall rock can reduce the dip to 30 deg and can account for shallow normal-slip earthquakes.

Ivins, E. R.↗

Investigation of acoustic waves under subsurface conditions to improve the predictions of rock mechanical properties and natural fracture characteristics

Mechanical properties and natural fracture characteristics are critical to investigate for subsurface engineering applications, including carbon storage, well drilling, and stimulation, as they govern rock stability, fluid flow, and mechanical behavior under stress. This dissertation integrates experimental and machine learning approaches to enhance the prediction and understanding of these properties by analyzing acoustic wave behavior under varied subsurface conditions. First, the influence of temperature, pore pressure, and supercritical CO2 (scCO2) saturation on poroelastic properties is examined using Gray Berea sandstone samples. The results show that temperature and pore pressure significantly affect the bulk modulus and Biot’s coefficient, while scCO2 saturation impacts rock compressibility, informing strategies for effective geological carbon storage. The study extends this understanding by experimentally evaluating the impact of reservoir depletion on the dynamic mechanical properties of the emerging Caney shale in South Oklahoma with the employment of unsupervised machine learning to predict static mechanical properties across the Caney shale. Integrating petrophysical data and chemostratigraphy, the workflow—featuring K-means clustering, principal component analysis (PCA), and inverse distance weighting (IDW)—improves stratigraphic characterization and the estimation of static-to-dynamic modulus ratios, which is vital for optimizing drilling and stimulation strategies. Finally, the work explores how natural fracture characteristics in shale influence acoustic waveforms and shear wave splitting (SWS) analysis. Experimental data on fractured samples under different stress and temperature conditions, combined with machine learning models such as K-nearest neighbors (KNN) and extreme gradient boosting (XGBoost), reveal key fracture properties impacting SWS and wave propagation. Together, these studies provide a comprehensive framework for linking acoustic wave behavior with rock properties, advancing the methods for monitoring and predicting geomechanical changes. The insights offered valuable implications for safer, more efficient CO2 injection, hydrocarbon extraction, and subsurface management.

Elkholy, Sherif↗

Dynamic fault weakening and strengthening by gouge compaction and dilatancy in a fluid-saturated fault zone

Fault gouge deformation likely plays a significant role in controlling the strength of mature, large-displacement faults. Experiments show that intact gouge deforms in an overall ductile and stable manner, readily compacting, but dilates and experiences brittle failure under large strain rate. Inelastic gouge compaction and dilatancy are modeled here using a combined Mohr-Coulomb and end-cap yield criterion in a dynamic rupture model of a strike-slip fault with strongly velocity-weakening friction. We show that large shear stress concentration ahead of the rupture associated with the rupture front causes the gouge layer to compact (e.g., by structural collapse and comminution), leading to rapidly elevated pore pressure and significant weakening of the principal fault surface. Shortly after the rupture front passes, strong dilatancy during strength drop and rapid sliding reduces pore pressure and strengthens the fault, promoting slip pulses. Large strain localization in the gouge layer occurs as a result of rapid gouge dilatancy and strain softening. The combination of prerupture weakening from compaction and restrengthening from dilatancy hardening leads to a smaller-strength drop, and limits the stress concentration outside the gouge layer. Furthermore, this leads to a reduction of inelastic shear strain in the damage zone, which is more consistent with geological observations and high-speed frictional experiments. With the presence of well-developed fault gouge, the strength of mature faults may be limited by end-cap rather than Mohr-Coulomb failure; thus, their frictional strengths are significantly smaller than Byerlee friction.

58 GEOSCIENCES↗

Enhanced Microseismicity During Production Pumping Cessation at the San Emidio Geothermal Field (Nevada, USA) in December 2016

Abstract Tectonic activity, geothermal fluids, and microseismic events (MSEs) tend to occur in similar locations as a result of spatiotemporal changes in the subsurface stress state. To quantify this association, we analyze data from a dense seismic array deployed at the San Emidio geothermal field, Nevada for 1 week in December 2016 to coincide with a 19.45‐hr shutdown of all injection and production pumping operations. 123 MSEs were detected, of which 101 occurred during the shutdown. The spatial association of the MSEs with the production wells suggests a causal relationship between the production cessation and the MSEs. Here we performed a detailed analysis to investigate reservoir material properties, distribution of seismically activated faults, and local stress state. We determined the hypocenters, magnitudes, and focal mechanisms for the MSEs, P‐wave tomographic velocity model, and local stress tensor. The results show that most MSEs occurred near the production wells. Magnitudes fall between −2.2 and 0.0 with larger events located closer to the production wells. Most MSEs occurred within a westward‐dipping normal fault zone in the reservoir associated with anomalously low P‐wave velocity values. The focal mechanism and stress inversion results show predominantly normal faulting with the maximum horizontal stress oriented north‐south. We suggest that the MSEs during shutdown were triggered on pre‐existing, small‐scale, critically stressed fault patches in the reservoir as the pore pressure increased around the production wells when the production pumping ceased. We interpret the larger MSE magnitudes closer to the production wells as a result of higher pore pressure increase.

15 GEOTHERMAL ENERGY↗

ChemoMechanical Controls on Induced Seismicity

In recent years, seismicity rates in the US have dramatically risen due to increased activity in onshore oil and gas production. This project attempts to tie observations about induced seismicity to dehydration reactions in laumontite, a common mineral found in fault gouge in crystalline basement formations. It is the hypothesis of this study that in addition to pressurerelated changes in the in situ stress state, the injection of wastewater pushes new fluids into crystalline fault fracture networks that are not in chemical equilibrium with the mineral assemblages, particularly laumontite in fault gouge. Experiments were conducted under hydrothermal conditions where samples of laumontite were exposed to NaC1 brines at different pH values. After exposure to different fluid chemistries for 8 weeks at 90° C, we did not observe substantial alteration of laumontite. In hydrostatic compaction experiments, all samples deformed similarly in the presence of different fluids. Pore pressure decreases were observed at the start of a 1 week hold at 85° C in a 1M NaC1 pH 3 solution, suggesting that acidic fluids might stabilize pore pressures in basement fault networks. Friction experiments on laumontite and kaolinite powders showed both materials have similar coefficients of friction. Mixtures with partial kaolinite content showed a slight decrease in the coefficient of friction, which could be sufficient to trigger slip on critically stressed basement faults.

58 GEOSCIENCES↗

Investigation of the influence of geomechanical and hydrogeological properties on surface uplift at In Salah [Systematic investigation of the influence of geomechanical and hydrogeological properties on surface uplift at In Salah]

Coupled reservoir and geomechanical simulations are significantly important to understand the long-term behavior of geologic carbon storage (GCS) systems. In this study, we performed coupled fluid flow and geomechanical modeling of CO 2 storage using available field data to (1) validate our existing numerical model and (2) perform parameter estimation via inverse modeling to identify the impact of key geomechanical (Young's modulus and Biot's coefficient) and hydrogeological (permeability and anisotropy ratio) properties on surface uplift and the pore pressure buildup at In Salah in Algeria. Furthermore, two sets of surface uplift data featuring low and high uplifts above two injection wells and the maximum change in the pore pressure due to CO 2 injection were used to constrain the inverse model.

58 GEOSCIENCES↗

Physics-based Induced Earthquake Forecasting: Process Understanding, and Hazards Mitigation

Disposal of saltwater co-produced with oil and gas is linked to elevated seismicity in the Central and Midwest US. There is a concern that these events may lead to widespread damage and an overall increase in seismicity. Thus an improved understanding of the spatially and temporally variable deformation and stress field associated with fluid injection operation is critically necessary for evaluating time-varying seismic hazards. Despite the improvements in seismic monitoring capacity and the resulting decrease in the magnitude detection threshold, estimates of induced earthquake probability remain elusive due to insufficient models incapable of accounting for the complex physics governing the process of induced seismicity. The proposed research effort will comprehensively analyze, integrate, and interpret geodetic, injection, and seismic data in the vicinity of the injection sites in Oklahoma to resolve the 4-dimensional distribution of pore pressure and stress in the shallow crust. This project, in particular, is focused on exploring the statistical relation between injection operation and increased earthquake hazard. The amplitude of and the extent to which pore pressure changes are determined by some factors, in particular, the hydrogeological properties of the rocks, such as diffusivity. Thus the available deformation data will be used to constrain hydrogeological properties of the medium, to accurately resolve the evolution of crustal stresses due to fluid injection. Having the time-varying models of stress changes, a statistical framework will be implemented to estimate the time-dependent probability of large earthquakes on the nearby fault systems. These data and models help to improve seismic hazard estimates and aid in constructing operational-induced earthquake forecast models. This information can also be integrated into the updated U.S. National Seismic Hazard Map, which local communities and authorities use in their earthquake risk estimates and mitigation efforts.

58 GEOSCIENCES↗

The effects of nearby fractures on hydraulically induced fracture propagation and permeability changes

Fracture propagation caused by hydraulic fracturing operations can be significantly influenced by adjacent fractures. In this paper, we present a detailed coupled hydro-mechanical analysis to study the effects of nearby natural fractures on hydraulically induced fracture propagation and changes in fracture permeability. Two rock domains were considered in comparison: FD1, with one fracture, and FD2, with two adjacent parallel or non-parallel fractures. It was assumed that water injection occurred in a borehole that intersected the single fracture in FD1 and one of the two fractures in FD2. Simulations were made for a time period of 3 h with an injection period of 2 h followed by 1 h of shut-in. An elastic-brittle model based on the degradation of material properties was implemented in a 2D finite-difference scheme and used for elements of the intact rock subjected to tension and shear failure. The intact rock was considered to have a low but non-negligible permeability. A verification study against analytical solutions showed that the fracture propagation and stress concentrations due to differential boundary stresses could be accurately represented by our model. Next, a base case was considered, in which the stress ratio (SR) between the magnitudes of the maximum and minimum boundary stresses, the permeability k R of the intact rock and the initial permeability k TF of the tension failure regions were fixed. In FD2, the distance d F between the two natural fractures defined by the closest distance was also fixed. The results showed that in both rock domains, the fracture started to propagate when the pore pressure was approximately 85% of the magnitude of the minimum boundary stress. The propagation of a single fracture was significantly greater than the propagation of a double fracture system because, in the latter case, the pore pressure decreased when the two fractures connected. As a result, changes in permeability in FD2 were smaller than in FD1. At the end of injection, the maximum ratios between the final and initial permeability of the natural fractures were found to be approximately 3 and 2 for rock domains FD1 and FD2, respectively. For non-parallel fractures, the controlling factor for fracture propagation was the separation between the tips of the pressurised fracture and the neighbouring non-pressurised fracture. A sensitivity study was conducted to study the influence of the key parameters d F , SR, k R and k TF on the simulation results. Lastly, fracture propagation showed more sensitivity to dF and SR than to the other parameters.

58 GEOSCIENCES↗

Insights Into Seismicity Associated With Flexibly Operating Enhanced Geothermal System From Real‐Time Distributed Acoustic Sensing

Enhanced Geothermal Systems (EGS) have the capacity to broaden the accessible resource pool for geothermal power generation. Traditionally viewed as a “baseload” resource, their flexible operation might also enable dispatchable load‐following generation and long‐term energy storage, aligning them with the evolving landscape of decarbonized electricity systems. However, increasing permeability and extracting energy during EGS operations can induce microseismic events; for many prior EGS efforts, some associated seismicity has been observed. While energetically beneficial, the flexibility of EGS operations prompts our inquiry into whether new types of operations will yield previously unseen seismicity patterns. We demonstrate the use of distributed acoustic sensing (DAS) with real‐time edge computing to monitor seismicity during a pilot test of a cyclically operated EGS facility at the Blue Mountain geothermal field. Our focus lies in uncovering seismicity insights from the real‐time microseismic catalog, particularly during load‐following dispatchability tests simulating flexible EGS operation. Here, we find that variations in pore pressure consistently correlate with seismicity, and that controlling pressure cycles during flexible operations appears to constrain microseismic activity during subsequent cycles. The spatio‐temporal evolution of microseismic clouds recorded during cyclic injection cycles fits diffusive models over our available observation period. Additionally, seismicity elevation lags behind pore pressure increases, likely due to pressure diffusion to the fracture system boundary. Through real‐time monitoring, we offer novel insights into seismicity associated with flexibly operating EGS. Our findings suggest that leveraging DAS and edge computing can inform EGS operations and help mitigate induced seismicity.

Chamarczuk, Michal [Rice Univ., Houston, TX (Unite↗