Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLATES, FLAT - STRESSES RECTANGULAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Laminar to Turbulence Transition in Boundary Layers due to Tripping Devices

Direct numerical simulations (DNS)and linear stability analysis were performed to identify the mechanisms by which two-and three-dimensional trips promote early transition in subsonic boundary layers over a flat plate. Investigations were conducted for two boundary layer transition trip configurations: one is a two-dimensional rectangular-shaped rod and the other is a three-dimensional zigzag tape. Reynolds numbers based on the trip heights are 683 and 300 for the two-and three-dimensional trips, respectively. Simulations with the two-dimensional trip showed that the flow separates at the top of the trip and forms a long recirculation zone downstream. However, the flow remains steady in the simulation without any external disturbances. Linear stability analysis showed that the inflectional profile in the recirculation zone is strongly unstable to frequencies in the range of 100-300 Hz. Simulations with the external disturbances forced at the frequency of 200 Hz showed that disturbances grow strongly inside the recirculation zone as observed in the Klebanoff1 experiment.

Transition↗
NASA NTRS1947

Distribution of wave drag and lift in the vicinity of wing tips at supersonic speeds

The point-source-distribution method of calculating the aerodynamic coefficients of thin wings at supersonic speeds was extended to include the effect of the region between the wing boundary and the foremost Mach wave from the wing leading edge. The effect of this region on the surface velocity potential has been determined by an equivalent function, which is evaluated over a portion of the wing surface. In this manner, the effect of angles of attack and yaw as well as the asymmetry of top and bottom wing surfaces may be calculated. As examples of the method, the pressure distribution on a thin plate wing of rectangular plan form as well as the lift and the drag coefficients as a function of Mach number, angle of attack, and aspect ratio are calculated. The equations for the surface velocity potential of several other plan forms are also included. (author)

AIRFOILS, FLAT-PLATE↗
NASA NTRS1939

Wind-tunnel Investigation of Ground Effect on Wings with Flaps

An investigation was conducted in the N.A.C.A. 7- by 10-foot wind tunnel to determine the effect of ground proximity on the aerodynamic characteristics of wings equipped with high-lift devices. A rectangular and a tapered wing were tested without flaps, with a split flap, and with a slotted flap. The ground was represented by a flat plate, completely spanning the tunnel and extending a considerable distance ahead and back of the model. The position of the plate was varied from one-half to three chord lengths below the wing. The results are presented in the form of curves of absolute coefficients, showing the effect of the ground on each wing arrangement. The effect of the ground on lift, drag, and pitching moment is discussed. An appendix gives equations for calculating tunnel-wall corrections to be applied to ground-effect tests conducted in rectangular tunnels when a plate is used to represent the ground. The tests indicated that the ground effect on wings with flaps is a marked decrease in drag, a decrease in diving moment, and a substantial reduction in maximum lift.

Recant, Isidore G↗
NASA NTRS2013

Flutter Analysis of the Thermal Protection Layer on the NASA HIAD

A combination of classical plate theory and a supersonic aerodynamic model is used to study the aeroelastic flutter behavior of a proposed thermal protection system (TPS) for the NASA HIAD. The analysis pertains to the rectangular configurations currently being tested in a NASA wind-tunnel facility, and may explain why oscillations of the articles could be observed. An analysis using a linear flat plate model indicated that flutter was possible well within the supersonic flow regime of the wind tunnel tests. A more complex nonlinear analysis of the TPS, taking into account any material curvature present due to the restraint system or substructure, indicated that significantly greater aerodynamic forcing is required for the onset of flutter. Chaotic and periodic limit cycle oscillations (LCOs) of the TPS are possible depending on how the curvature is imposed. When the pressure from the base substructure on the bottom of the TPS is used as the source of curvature, the flutter boundary increases rapidly and chaotic behavior is eliminated.

Goldman, Benjamin D.↗
NASA NTRS1993

Simulations Of Three-Dimensional Flow With Separation

Report discusses numerical solutions of Navier-Stokes equations for viscous supersonic flow over fin protruding from flat plate. Two types of configurations considered: one with wedge-shaped fin (sharp edge facing upstream), other with blunt (rectangular parallelepiped) fin. Only steady flows considered. Computations performed to study phenomena involved in separations of three-dimensional flows.

Hung, Ching-Mao↗
NASA NTRS1990

Experimental Investigation of Porous-floor Effects on Cavity Flow Fields at Supersonic Speeds

An experimental investigation was conducted to determine the effectiveness of a passive-venting system to modify the flow field characteristics of a rectangular-box cavity at supersonic speeds. The passive-venting system consists of a porous floor with a vent chamber beneath the floor. For certain cavity length-to-height ratios, this configuration allowed high-pressure air at the rear of the cavity to vent to the forward part of the cavity, thereby modifying the cavity flow field. The wind-tunnel model consisted of a flat plate that housed a cavity mounted on a balance such that only the cavity drag was measured. The cavity height remained constant, and the length varied with rectangular-block inserts. Both solid-and porous-floor cavities were tested for comparison at Mach numbers of 1.60, 1.90, 2.16, and 2.86. These results showed that the passive-venting system did modify the cavity flow field. In order to determine the type flow field which existed for the porous-floor configuration, pressures were measured inside the cavity at the same conditions and for the same configurations as those used in the drag tests. Pressure data were also obtained with stores mounted in the cavity. These results, along with Schlieren photographs and the tabulated data, are presented to document the porous-floor cavity flow field.

Wilcox, Floyd J., Jr.↗
NASA NTRSDate not supplied

Laminar to Turbulence Transition in Boundary Layers due to Tripping Devices

Direct numerical simulations (DNS)and linear stability analyses were performed to identify the mechanisms by whichtwo-and three-dimensional trips promote early transition in subsonic boundary layers over a flat plate. Investigations were conducted for threeboundary-layer transition trip configurations:a two-dimensional smooth hump,a two-dimensional rectangular-shapedrod and a three-dimensional zig-zagtape. The smooth hump was used by Park et al.1in the linear and nonlinear parabolized stability (PSE) computations. Reynolds numbersbased on the tripheights are 710, 683,and 300 for the two-and three-dimensional trips, respectively. Simulations withthe smooth hump showed that the flow becomes stable upstream and strongly unstable downstream of the hump. Simulations with the two-dimensional rectangular trip showed that the flow separates at the top of the trip and forms a long recirculation zonedownstream. However, the flow remains steady in the simulation without any external disturbances. Linear stability analysis showed that the inflectional profile in the recirculation zone is strongly unstable to frequencies in the range of 100-300 Hz. Simulations with the external disturbances forced at the frequency of 200 Hz showed that disturbances grow strongly inside the recirculation zone as observed in the Klebanoff2 experiment. Three-dimensional simulations with secondary disturbances of fundamental, subharmonic, and oblique types produced turbulent flows shortlydownstream. The three-dimensional zig-zag trip with a small roughness Reynolds number lead to early breakdown to a turbulent flow.

Stability↗
NASA NTRS1987

Near-wall turbulence alteration through thin streamwise riblets

The possibility of improving the level of drag reduction associated with near-wall riblets is considered. The methodology involves the use of a hot-wire anemometer to study various surface geometries on small, easily constructed models. These models consist of small, adjacent rectangular channels on the wall aligned in the streamwise direction. The VITA technique is modified and applied to thin-element-array and smooth flat-plate data and the results are indicated schematically.

Wilkinson, Stephen P.↗
NASA NTRS1988

Effect of large amplitude pitching motions on the unsteady aerodynamic characteristics of flat-plate wings

Large-amplitude unsteady motion effects on the aerodynamic force and stability characteristics of flat-plate wings were investigated in a wind tunnel for the cases of two delta wings with respective leading edge sweeps of 70 and 45 deg, and a rectangular wing whose aspect ratio was equal to that of the 70-deg delta wing. Attention was given to the effects of reduced frequency and mean angle of attack. It is found that lags in vortex burst location and separation/reattachment of flow on the upper surface of the wing produced large overshoots and hysteresis loops in normal force and pitching moment coefficients that were a strong function of mean oscillation angle and reduced frequency.

Brandon, Jay M.↗
DOE OSTI2021

ITER cold VDEs in the limit of perfectly conducting walls

Recently, it has been shown that a vertical displacement event (VDE) can occur in ITER even when the walls are perfect conductors, as a consequence of the current quench (CQ) [A. H. Boozer, Phys. Plasmas 26, 114501 (2019)]. We used the extended-MHD code M3D-C1 with an ITER-like equilibrium and induced a CQ to explore cold VDEs in the limit of perfectly conducting walls, using different wall geometries. In the case of a rectangular first wall with the side walls far away from the plasma, we obtained very good agreement with the analytical model developed by Boozer that considers a top/bottom flat-plates wall. We show that the solution in which the plasma remains at the initial equilibrium position is improved when bringing the side walls closer to the plasma. When approximating the ITER first wall as a perfect conductor, the plasma remains stable at the initial equilibrium position far beyond the value predicted by the flat-plates wall limit. When considering an opposite limit in which only the inner shell of the ITER vacuum vessel acts as a perfect conductor, the plasma is displaced during the CQ, but the edge safety factor remains above 2 longer in the current decay compared to the flat-plates wall limit. In all the simulated cases, the VDE is found to be strongly dependent on the plasma current, in agreement with a similar finding in the flat-plates wall limit, showing an important difference with hot VDEs in which the CQ is not a necessary condition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1991

Active control of panel vibrations induced by boundary-layer flow

Some problems in active control of panel vibration excited by a boundary layer flow over a flat plate are studied. In the first phase of the study, the optimal control problem of vibrating elastic panel induced by a fluid dynamical loading was studied. For a simply supported rectangular plate, the vibration control problem can be analyzed by a modal analysis. The control objective is to minimize the total cost functional, which is the sum of a vibrational energy and the control cost. By means of the modal expansion, the dynamical equation for the plate and the cost functional are reduced to a system of ordinary differential equations and the cost functions for the modes. For the linear elastic plate, the modes become uncoupled. The control of each modal amplitude reduces to the so-called linear regulator problem in control theory. Such problems can then be solved by the method of adjoint state. The optimality system of equations was solved numerically by a shooting method. The results are summarized.

Chow, Pao-Liu↗
NASA NTRS1991

A numerical study of shock wave/boundary layer interaction in nonequilibrium chemically reacting air - The effects of catalytic walls

This paper presents a numerical study that investigate the effects of nonequilibrium chemistry, and in particular, wall catalycity on the separated flow region generated by an oblique shock wave impinging upon a flat plate boundary layer. To obtain a solution to this problem, the full two dimensional Navier-Stokes equations were solved using MacCormack's predictor-corrector time dependent technique on a rectangular grid. Nonequilibrium chemistry was included by utilizing the 5 species, 17 reaction modified Dunn-Kang chemical kinetics model. Separate results were obtained for: calorically perfect, chemically reacting - noncatalytic wall, and chemically reacting - fully catalytic wall cases, for a given set of flow conditions. A direct comparison of all three cases revealed a slight decrease in the peak heat transfer for the noncatalytic wall case, as compared to the calorically perfect case. On the other hand, the fully catalytic wall case had a tremendous increase in the peak surface heat transfer. It is concluded that, for the particular conditons treated here (nearly frozen flow in the free stream), the effects of the nonequilibrium chemically reacting flow on the shock-wave/boundary-layer interaction depend critically on the catalycity of the wall, having virtually no effect for the case of a noncatalytic wall, and exerting a tremendous effect for a fully catalytic wall.

Grumet, Adam A.↗
NASA NTRS1978

Drag and heat transfer on surfaces with small longitudinal fins

An investigation is conducted regarding the drag characteristics of longitudinally ribbed surfaces using various configurations which attempt to confine the turbulent wall bursts to regions of small transverse extent in the initial birth region. The ratio of heat transfer increase to drag increase for the high area ratio rib configurations is determined and the heat transfer efficiency of the present surfaces is compared with data found in the literature. The drag data obtained indicate local 'wetted area skin friction' reductions but due to the increased surface area the planform drag is increased in most instances. There is no indication of drag reduction with the rectangular ribbed models that had sharp leading and fin tip edges. Heat transfer data indicate that several of the triangular grooved models have efficiencies approximately 10 percent higher than that of a smooth flat plate.

Walsh, M. J.↗
NASA NTRS1959

Flutter Tests of Some Simple Models at a Mach Number of 7.2 in Helium Flow

Results of hypersonic flutter tests on some simple models are presented. The models had rectangular plan forms of panel aspect ratio 1.0, no sweepback, and bending-to-torsion frequency ratios of about 1/3. Two airfoil sections were included in the tests; double wedges of 5-, 10-, and 15-percent thickness and flat plates with straight, parallel sides and beveled leading and trailing edges. The models were supported by a cantilevered shaft. The double-wedge wings were tested in helium at a Mach number of 7.2. An effect of airfoil thickness on flutter speed was found, thicker wings requiring more stiffness to avoid flutter. A few tests in air at a Mach number of 6.9 showed the same thickness effect and also indicated that tests in helium would predict conservative flutter boundaries in air. The data in air and helium seemed to be correlated by piston-theory calculations. Piston-theory calculations agreed well with experiment for the thinner models but began to deviate as the thickness parameter MT approached and exceeded 1.0. A few tests on flat-plate models with various elastic-axis locations were made. Piston-theory calculations would not satisfactorily predict the flutter of these models, probably because of their blunt leading edges.

Morgan, Homer G.↗
NASA NTRS1989

An experimental and analytical investigation of the effect of spanwise curvature on wing flutter at Mach number of 0.7

An experimental and analytical study was conducted at Mach 0.7 to investigate the effects of spanwise curvature on flutter. Two series of rectangular planform wings of aspect ration 1.5 and curvature ranging from zero (uncurved) to 1.04/ft were flutter tested in the NASA Langley Transonic Dynamics Tunnel (TDT). One series consisted of models with a NACA 65 A010 airfoil section and the other of flat plate cross section models. Flutter analyses were conducted for correlation with the experimental results by using structural finite element methods to perform vibration analysis and two aerodynamic theories to obtain unsteady aerodynamic load calculations. The experimental results showed that for one series of models the flutter dynamic pressure increased significantly with curvature while for the other series of models the flutter dynamic pressure decreased with curvature. The flutter analyses, which generally predicted the experimental results, indicated that the difference in behavior of the two series of models was primarily due to differences in their structural properties.

Rivera, Jose A., Jr.↗
NASA NTRS2020

Transition induced by Streamwise Arrays of Roughness Elements on a Flat Plate in Mach 3.5 Flow

The flow behind streamwise arrays of roughness elements was examined with a hot-wire probe. The roughness elements had heights of approximately 20% and 40% of the boundary layer thickness and different spacings and orientations of these roughness elements were tested. The circular roughness elements were spaced two diameters apart or four diameters apart from center to center. Transition moved upstream only when the roughness elements were spaced four diameters apart. The rectangular roughness elements were oriented so that they were at a 45-degree angle relative to the leading edge of the plate. Tandem rectangular elements either had the same orientation or opposing orientation. Mean mass-flux and total-temperature profiles of the flow field downstream of the roughness elements were examined for mean-flow distortion. Mass-flux fluctuation profiles showed that a 45-kHz odd-mode disturbance was present downstream of the shorter circular roughness elements. The dominant instability downstream of the taller circular roughness elements was a 65–85 kHz even-mode disturbance. Mass-flux fluctuation profiles showed that the dominant mode downstream of the tandem rectangular roughness elements with the same orientation was similar to that of a single roughness element and centered at a frequency of approximately 55 kHz. The 55-kHz instability appeared to correspond to increased spanwise shear, and thus was determined to be an odd-like mode. The dominant instability downstream of the tandem roughness elements with opposing orientation was centered at a frequency of 65 kHz and did not transition in the measurement region.

Amanda Chou↗
NASA NTRS1951

Sideslip in a viscous compressible gas

By an analysis of the Navier-Stokes equations it is shown that the aerodynamic coefficients of an infinite rectangular swept wing in an isothermal or adiabatic flow of a compressible gas can be determined from the aerodynamic coefficients of the unswept wing. When the flow is neither isothermal nor adiabatic, a three-dimensional boundary layer theory is developed and applied to the special case of a swept flat plate.

THEORIES - WINGS, SWEEPBACK & SWEEPFORWARD↗