Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PARTIAL PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Instrument for stable high temperature Seebeck coefficient and resistivity measurements under controlled oxygen partial pressure

The transport properties of ceramic materials strongly depend on oxygen activity, which is tuned by changing the partial oxygen pressure (pO 2 ) prior to and during measurement. Within, we describe an instrument for highly stable measurements of Seebeck coefficient and electrical resistivity at temperatures up to 1300 K with controlled oxygen partial pressure. An all platinum construction is used to avoid potential materials instabilities that can cause measurement drift. Two independent heaters are employed to establish a small temperature gradient for Seebeck measurements, while keeping the average temperature constant and avoiding errors associated with pO 2 -induced drifts in thermocouple readings. Oxygen equilibrium is monitored using both an O 2 sensor and the transient behavior of the resistance as a proxy. A pO 2 range of 10 -25 –10 0 atm can be established with appropriate gas mixtures. Seebeck measurements were calibrated against a high purity platinum wire, Pt/Pt–Rh thermocouple wire, and a Bi 2 Te3 Seebeck coefficient Standard Reference Material. To demonstrate the utility of this instrument for oxide materials we present measurements as a function of pO 2 on a 1 % Nb-doped SrTiO 3 single crystal, and show systematic changes in properties consistent with oxygen vacancy defect chemistry. Thus, an approximately 11% increase in power factor over a pO 2 range of 10 -19 –10 -8 atm at 973 K for the donor-doped single crystals is observed.

36 MATERIALS SCIENCE↗

Crystallographic texture control of sputtered HfN thin films using low oxygen partial pressures

The authors studied the development of crystallographic texture in hafnium nitride (HfN) films deposited by off-normal incidence reactive magnetron sputtering at room temperature. Films are prepared with and without added oxygen in N{sub 2}/Ar mixtures. Texture measurements were performed by x-ray pole figure analysis of the (111) and (200) diffraction peaks. The authors found that HfN deposited at 40 deg. without added oxygen has a strong <100> fiber texture with no in-plane alignments showing the dominance of thermodynamic effects in the course of texture evolution. Oxygen is deliberately introduced into the sputtering gas ambient to study its effects on microstructure formation. As the oxygen partial pressure (O{sub 2} pp) is increased in the range of 1.33x10{sup -5} to 1.33x10{sup -4} Pa, HfN out-of-plane orientation changed to <111> with a substantial in-plane alignment in <100> direction as well. In this case, texture analysis of each individual diffraction peak revealed the existence of two populations of grains indicating a competition between (111) and (200) planes. A transition towards hafnium oxynitride phases occurred at high O{sub 2} pp's. The authors propose that oxygen presence during deposition reduces the adatom surface mobility, which enables kinetic effects to govern the texture formation and thus leads to a biaxial alignment in HfN films.

36 MATERIALS SCIENCE↗

Maximizing the Hydrogen Photoproduction Yields in Chlamydomonas Reinhardtii Cultures: The Effect of the H2 Partial Pressure

Photoproduction of H{sub 2} gas has been examined in sulfur/phosphorus-deprived Chalmydomonas reinhardtii cultures, placed in photobioreactors (PhBRs) with different gas phase to liquid phase ratios (V{sub g.p.}/V{sub l.p.}). The results demonstrate that an increase in the ratio stimulates H{sub 2} photoproduction activity in both algal suspension cultures and in algae entrapped in thin alginate films. In suspension cultures, a 4x increase (from {approx}0.5 to {approx}2) in V{sub g.p.}/V{sub l.p} results in a 2x increase (from 10.8 to 23.1 mmol l{sup -1} or 264-565 ml l{sup -1}) in the total yield of H{sub 2} gas. Remarkably, 565 ml of H{sub 2} gas per liter of the suspension culture is the highest yield ever reported for a wild-type strain in a time period of less than 190 h. In immobilized algae, where diffusion of H{sub 2} from the medium to the PhBR gas phase is not affected by mixing, the maximum rate and yield of H{sub 2} photoproduction occur in PhBRs with V{sub g.p.}/V{sub l.p} above 7 or in a PhBR with smaller headspace, if the H{sub 2} is effectively removed from the medium by continuous flushing of the headspace with argon. These experiments in combination with studies of the direct inhibitory effect of high H{sub 2} concentrations in the PhBR headspace on H{sub 2} photoproduction activity in algal cultures clearly show that H{sub 2} photoproduction in algae depends significantly on the partial pressure of H{sub 2} (not O{sub 2} as previously thought) in the PhBR gas phase.

08 HYDROGEN↗

Chemical and structural changes in Ln{sub 2}NiO{sub 4+δ} (Ln=La, Pr or Nd) lanthanide nickelates as a function of oxygen partial pressure at high temperature

The chemical stability of lanthanide nickelates Ln{sub 2}NiO{sub 4+δ} (Ln=La, Pr or Nd) has been studied in the temperature range 25–1300 °C, either in air or at low pO{sub 2} (down to 10{sup −4} atm). Thermal gravimetry analysis (TGA) measurements coupled with X-ray diffraction (XRD) characterization have shown that all compounds retain their K{sub 2}NiF{sub 4}-type structure in these conditions, while remaining over-stoichiometric in oxygen up to 1000 °C. Only Nd{sub 2}NiO{sub 4+δ} starts to decompose into Nd{sub 2}O{sub 3} and NiO above 1000 °C, at pO{sub 2}=10{sup −4} atm. In addition, a careful analysis of the lanthanide nickelates structural features has been performed by in situ XRD, as a function of temperature and pO{sub 2}. For all compounds, a structural transition has been always observed in the temperature range 200–400 °C, in air or at pO{sub 2}=10{sup −4} atm. In addition, their cell volume did not vary upon the variation of the oxygen partial pressure. Therefore, these materials do not exhibit a chemical expansion in these conditions, which is beneficial for a fuel cell application as cathode layers. Additional dilatometry measurements have revealed that a temperature as high as 950 °C for Pr{sub 2}NiO{sub 4+δ} or 1100 °C for La{sub 2}NiO{sub 4+δ} and Nd{sub 2}NiO{sub 4+δ} has to be reached in order to begin the sintering of the material particles, which is of primary importance to obtain an efficient electronic/ionic conduction in the corresponding designed cathode layers. Besides, excellent matching was found between the thermal expansion coefficients of lanthanide nickelates and SOFC electrolytes such as 8wt% yttria stabilized zirconia (8YSZ) or Ce{sub 0.8}Gd{sub 0.2}O{sub 2−δ} (GDC), at least from 400 °C up to 1400 °C in air or up to 1200 °C at pO{sub 2}=10{sup −4} atm. - Graphical abstract: This study reports the good chemical stability of oxygen overstoichiometric Ln2NiO4+δ(Ln = La, Pr or Nd) at high temperatures (up to 1300 °C), eitherin air or at pO2down to 10-4 atm. In addition, these MSC cathode materials show a small chemical expansion as well as a good TEC compatibility with electrolyte materials (GDC or YSZ). - Highlights: • The structure of Ln2NiO4+δ compounds are studied vs. temperature and pO2 • Structural transitions are evidenced in air as well as in low pO2 atmosphere • The structural transitions do not significantly affect their TECs values • Up to 1200 °C, they show good chemical stability and no chemical expansion vs. pO2 • TECs of nickelates, 8YSZ and GDC are compared in air and in low pO2 atmosphere.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On multidomain multiscale modeling and simulation of a novel partial pressure and temperature swing adsorptive reactor ($\mathrm{PPTSAR}$) with application to the water gas shift reaction

Here in this work, a dynamic, multidomain, multiscale model of a novel Partial Pressure and Temperature Swing Adsorptive Reactor (PPTSAR) Process is developed and simulated for a Water Gas Shift Reaction (WGSR) application. The proposed model couples the reactor wall, catalyst/adsorbent pellet, and fluid mixture domains at their respective scales to comprehensively model mass, momentum, and energy transport phenomena occurring within each domain. The resulting model elucidates the PPTSAR’s start-up, transient, and long-term, periodic, dynamic behavior, during both adsorption/reaction and desorption operating modes. In the WGSR application considered, the use of two PPTSARs is shown to allow continuous operation that delivers CO conversion greater than 95% with simultaneous complete CO 2 capture.

42 ENGINEERING↗

Development of an infrared absorption transducer to monitor partial pressure of carbon dioxide for space applications

An infrared (IR) carbon dioxide (CO2) transducers has been designed, developed, and produced for space applications. The transducer provides measurement of partial pressure of CO2 in life support applications, including the Extravehicular Mobility Unit (EMU), Space Shuttle Orbiter and Spacehab. The electrochemical sensor presently used for these applications has a slow reponse time and has reliability concerns due to the electrolyte. The new microprocessor based unit has a fast response time and can be tailored to other space applications.

Lutz, Glenn↗

Measurement of partial pressures in vacuum technology and vacuum physics

It is pointed out that the measurement of gaseous pressures of less than 0.0001 torr is based on the ionization of gas atoms and molecules due to collisions with electrons. The particle density is determined in place of the pressure. The ionization cross sections for molecules of various gases are discussed. It is found that the true pressure in a vacuum system cannot be determined with certainty if it is unknown which gas is present. Effects of partial pressure determination on the condition of the vacuum system are discussed together with ion sources, systems of separation, and ion detection.

Huber, W. K.↗

Annealing temperature and O2 partial pressure dependence of T(sub c) in HgBa2CuO(4+delta)

Samples of HgBa2CuO(4+delta) (Hg-1201) were annealed under various conditions. After carefully controlling annealing time, annealing temperature (T(sub a)) and O2 partial pressure (P(sub 0)), we were able to find the reversible annealing conditions for Hg-1201. Under 1 atm O2 at 260 C less than or equal to T(sub a) less than or equal to 400 C, the obtained T(sub c) is nearly the same (approximately 97 K). However, it decreases quickly with T(sub a) greater than 300 C in high vacuum (P(sub 0) approximately 10(exp -8) atm), and reaches zero at T(sub a) = 400 C. On the other hand, T(sub c) decreases with the decrease of T(sub a) in high-pressure O2 (approximately 500 atm) and reaches approximately 20 K at about 240 C. In the entire annealing region, the oxygen surplus varies significantly from 0.03 to 0.4, and a wide range of T(sub c) variation (0 goes to 97 K goes to 20 K) was obtained with anion doping alone.

Xiong, Q.↗

Partial Pressures of In-Se from Optical Absorbance of the Vapor

The optical absorbance of the vapor phase over various In-Se compositions between 33.3 and 61 atomic percent and 673 and 1418K has been measured and used to obtain the partial pressures of Se2(g) and In2Se(g). The results are in agreement with silica Bourdon gage measurements for compositions between 50 and 61 atomic percent but significantly higher than those from Knudsen cell and simultaneous Torsion-Knudsen cell measurements. The sequiselenide is found to sublime incongruently. Congruent vaporization occurs for the liquid above 1000 K between 50.08 and 56 at. percent Se. The Gibbs energy of formation of the liquid from its pure liquid elements between 1000 and 1300K is essentially independent of temperature and falls between -36 and -38 kJ per gram atomic weight for 50 and 56 percent Se at 1200 and 1300K.

Brebrick, R. F.↗

Partial Pressures for Several In-Se Compositions from Optical Absorbance of the Vapor

The optical absorbance of the vapor phase over various In-Se compositions between 33.3-60.99 at.% Se and 673-1418 K was measured and used to obtain the partial pressures of Se2(g) and In2Se(g). The results are in agreement with silica Bourdon gauge measurements for compositions between 50-61 at.%, but significantly higher than those from Knudsen cell and simultaneous Knudsen-torsion cell measurements. It is found that 60.99 at.% Se lies outside the sesquiselenide homogeneity range and 59.98 at.% Se lies inside and is the congruently melting composition. The Gibbs energy of formation of the liquid from its pure liquid elements between 1000-1300 K is essentially independent of temperature and falls between -36 to -38 kJ per g atomic weight for 50 and 56% Se at 1200 and 1300 K.

Brebrick, R. F.↗

CO2 partial pressure and fluxes in the Amazon River Plume using in situ and remote sensing data

Estimations of the global carbon budget include a quantitative understanding of the evolving processes that occur along river-to-ocean gradients. However, high spatiotemporal resolution observations of these processes are limited. Here we present in situ measurements of the partial pressure of CO2 (pCO2) made through the Amazon River plume (ARP) during different discharge seasons, from 2010-2012. We evaluated the spatiotemporal distribution of pCO2 using Soil Moisture and Ocean Salinity (SMOS) satellite observations for each hydrologic period in the ARP. Regression models were used to estimate pCO2 at the ARP for the period of 2010-2014. From these distributions we calculated sea-air gas exchange of CO2 between the plume waters and the atmosphere (F_co2^sea). Intra-annual variability of F_co2^sea was related to discharge at the river mouth and ocean currents as well as trade winds in the plume. Climatic events during the study period had a significant impact on the F_co2^sea. Including the plume area closer to the river mouth makes the ARP a net source of CO2 with an annual net sea-air flux of 8.6 ±7.1 Tg C y-1 from 2011-2014.

Amazon↗

Oxidation of SiC/BN/SiC Composites in Reduced Oxygen Partial Pressures

SiC fiber-reinforced SiC composites with a BN interphase are proposed for use as leading edge structures of hypersonic vehicles. The durability of these materials under hypersonic flight conditions is therefore of interest. Thermogravimetric analysis was used to characterize the oxidation kinetics of both the constituent fibers and composite coupons at four temperatures: 816, 1149, 1343, and 1538 C (1500, 2100, 2450, and 2800 F) and in oxygen partial pressures between 5% and 0.1% (balance argon) at 1 atm total pressure. One edge of the coupons was ground off so the effects of oxygen ingress into the composite could be monitored by post-test SEM and EDS. Additional characterization of the oxidation products was conducted by XPS and TOF-SIMS. Under most conditions, the BN oxidized rapidly, leading to the formation of borosilicate glass. Rapid initial oxidation followed by volatilization of boria lead to protective oxide formation and further oxidation was slow. At 1538C in 5% oxygen, both the fibers and coupons exhibited borosilicate glass formation and bubbling. At 1538C in 0.1% oxygen, active oxidation of both the fibers and the composites was observed leading to rapid SiC degradation. BN oxidation at 1538C in 0.1% oxygen was not significant.

Opila, Elizabeth J.↗

A Free Energy Analysis of the Stability of Erbium oxide with respect to Plutonium metal, Plutonium Hydride Solid and Hydrogen Gas at Temperatures from 200C to 850C and Partial Pressures of Hydrogen from 0.1 Torr to 100 Torr

Free energy curves were built for erbium and plutonium metal, their hydrides and their oxides, as well as water and hydrogen gas. The free energy curves were then used to determine the free energy for reaction between these phases. In particular, the reactions between erbium sesquioxide and hydrogen, plutonium metal, and plutonium hydride were studied. The findings indicated that erbium sesquioxide is inert to reaction with hydrogen gas (for all realistic ranges of water partial pressure) and plutonium metal, but that the erbium sesquioxide is predicted to be reactive with plutonium hydride. Note that this latter point indicates a thermodynamic tendency, with no particular reference to the kinetics of the actual process.

36 MATERIALS SCIENCE↗

Analysis of the CO 2 Chemisorption in Li 5 FeO 4 , a New High Temperature CO 2 Captor Material. Effect of the CO 2 and O 2 Partial Pressures

Pentalithium ferrite (Li 5 FeO 4 ) was tested in this paper as possible CO 2 captor, both by theoretical calculations and experimental measurements. The pristine Li 5 FeO 4 compound with orthorhombic structure was synthesized via solid-state reaction and it was structural and microstructurally characterized. Later, sample was heat-treated at temperatures from room temperature to 900 °C under different CO 2 or CO 2 –O 2 atmospheres. Li 5 FeO 4 exhibits excellent CO 2 chemisorption abilities with a capture capacity about 12.9 mmol/g, which is outstanding in comparison to other previously reported ceramic captors. This material is able to react with CO 2 from 200 °C to approximately 715 °C showing a high kinetic of reaction even at CO 2 partial pressure values as low as 0.2. Finally and additionally, results suggest that oxygen addition does enhance the CO 2 chemisorption on Li 5 FeO 4 at temperatures below 700 °C, although oxygen addition seems to favor the desorption process at higher temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of varying oxygen partial pressure on molten silicon-ceramic substrate interactions

The silicon sessile drop contact angle was measured on hot pressed silicon nitride, silicon nitride coated on hot pressed silicon nitride, silicon carbon coated on graphite, and on Sialon to determine the degree to which silicon wets these substances. The post-sessile drop experiment samples were sectioned and photomicrographs were taken of the silicon-substrate interface to observe the degree of surface dissolution and degradation. Of these materials, silicon did not form a true sessile drop on the SiC on graphite due to infiltration of the silicon through the SiC coating, nor on the Sialon due to the formation of a more-or-less rigid coating on the liquid silicon. The most wetting was obtained on the coated Si3N4 with a value of 42 deg. The oxygen concentrations in a silicon ribbon furnace and in a sessile drop furnace were measured using the protable thoria-yttria solid solution electrolyte oxygen sensor. Oxygen partial pressures of 10 to the minus 7 power atm and 10 to the minus 8 power atm were obtained at the two facilities. These measurements are believed to represent nonequilibrium conditions.

Ownby, D. P.↗