SEARCH · Engineering Papers

Results for “Nonlinear reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Accuracy of telemetry signal power loss in a filter as an estimate for telemetry degradation

When telemetry data is transmitted through a communication link, some degradation in telemetry performance occurs as a result of the imperfect frequency response of the channel. The term telemetry degradation as used here is the increase in received signal power required to offset this filtering. The usual approach to assessing this degradation is to assume that it is equal to the signal power loss in the filtering, which is easily calculated. However, this approach neglects the effects of the nonlinear phase response of the filter, the effect of any reduction of the receiving system noise due to the filter, and intersymbol interference. Here, an exact calculation of the telemetry degradation, which includes all of the above effects, is compared with the signal power loss calculation for RF filtering of NRZ data on a carrier. The signal power loss calculation is found to be a reasonable approximation when the filter follows the point at which the receiving system noise is introduced, especially if the signal power loss is less than 0.5 dB. The signal power loss approximation is less valid when the receiving system noise is not filtered.

Koerner, M. A.↗

NASA NTRS2000

Effects of Imperfections on the Buckling Response of Compression-Loaded Composite Shells

The results of an experimental and numerical study of the effects of imperfections on the buckling response of unstiffened thin-walled composite cylindrical shells are presented. Results that identify the individual and combined effects of traditional initial geometric shell-wall imperfections and non-traditional shell-wall thickness variations, shell-end geometric imperfections and variations in loads applied to the ends of the shells on the shell buckling response are included. In addition, results illustrating the effects of manufacturing flaws in the form of gaps between adjacent pieces of graphite-epoxy tape in some of the laminate plies are presented in detail. The shells have been analyzed with a nonlinear finite-element analysis code that accurately accounts for these effects on the buckling and nonlinear responses of the shells. The numerical results indicate that traditional and nontraditional initial imperfections can cause a significant reduction in the buckling load of a compression-loaded composite shell. Furthermore, the results indicate that the imperfections couple in a nonlinear manner. The numerical results correlate well with the experimental results. The nonlinear analysis results are also compared to the results from a traditional linear bifurcation buckling analysis. The results suggest that the nonlinear analysis procedure can be used for determining accurate, high-fidelity design knockdown factors for shell buckling and collapse. The results can also be used to determine the effects of manufacturing tolerances on the buckling response of composite shells.

Hilburger, Mark W.↗

NASA NTRS1990

Projection and assembly method for multibody component model reduction

The problem addressed is that of obtaining reduced-order component models for use in simulating the dynamics of a multibody system. In certain cases, nonlinear system models may be constructed using linear dynamic models for each component, but allowing large angle motion between components. Without some form of model reduction, system models constructed in this manner may be too large for use in control system design and simulation trades. This paper analyzes one method of component model reduction that allows systems level requirements (e.g., capturing the effect of body 1 reaction wheel noise on body 2 camera pointing) to aid in the selection of the reduced-order component models. Briefly stated, important modes are selected at the system level and projected onto the components, and reduced-order components are then assembled into a reduced-order system model that retains the projected modes.

Bernard, Douglas E.↗

NASA NTRS1980

Theoretical prediction of nonlinear propagation effects on noise signatures generated by subsonic or supersonic propeller or rotor-blade tips

The nonlinear propagation equations for sound generated by a constant speed blade tip are presented. Propagation from a subsonic tip is treated as well as the various cases that can occur at supersonic speeds. Some computed examples indicate that the nonlinear theory correlates with experimental results better than linear theory for large amplitude waves. For swept tips that generate a wave with large amplitude leading expansion, the nonlinear theory predicts a cancellation effect that results in a significant reduction of both amplitude and impulse.

Barger, R. L.↗

NASA NTRS1989

A closed-form trim solution yielding minimum trim drag for airplanes with multiple longitudinal-control effectors

Airplane designs are currently being proposed with a multitude of lifting and control devices. Because of the redundancy in ways to generate moments and forces, there are a variety of strategies for trimming each airplane. A linear optimum trim solution (LOTS) is derived using a Lagrange formulation. LOTS enables the rapid calculation of the longitudinal load distribution resulting in the minimum trim drag in level, steady-state flight for airplanes with a mixture of three or more aerodynamic surfaces and propulsive control effectors. Comparisons of the trim drags obtained using LOTS, a direct constrained optimization method, and several ad hoc methods are presented for vortex-lattice representations of a three-surface airplane and two-surface airplane with thrust vectoring. These comparisons show that LOTS accurately predicts the results obtained from the nonlinear optimization and that the optimum methods result in trim drag reductions of up to 80 percent compared to the ad hoc methods.

Goodrich, Kenneth H.↗

NASA NTRS1992

Investigation on the use of optimization techniques for helicopter airframe vibrations design studies

Results of the investigation of formal nonlinear programming-based numerical optimization techniques of helicopter airframe vibration reduction are summarized. The objective and constraint function and the sensitivity expressions used in the formulation of airframe vibration optimization problems are presented and discussed. Implementation of a new computational procedure based on MSC/NASTRAN and CONMIN in a computer program system called DYNOPT for optimizing airframes subject to strength, frequency, dynamic response, and dynamic stress constraints is described. An optimization methodology is proposed which is thought to provide a new way of applying formal optimization techniques during the various phases of the airframe design process. Numerical results obtained from the application of the DYNOPT optimization code to a helicopter airframe are discussed.

Sreekanta Murthy, T.↗

NASA NTRS1996

A Computational and Experimental Study of Nonlinear Aspects of Induced Drag

Despite the 80-year history of classical wing theory, considerable research has recently been directed toward planform and wake effects on induced drag. Nonlinear interactions between the trailing wake and the wing offer the possibility of reducing drag. The nonlinear effect of compressibility on induced drag characteristics may also influence wing design. This thesis deals with the prediction of these nonlinear aspects of induced drag and ways to exploit them. A potential benefit of only a few percent of the drag represents a large fuel savings for the world's commercial transport fleet. Computational methods must be applied carefully to obtain accurate induced drag predictions. Trefftz-plane drag integration is far more reliable than surface pressure integration, but is very sensitive to the accuracy of the force-free wake model. The practical use of Trefftz plane drag integration was extended to transonic flow with the Tranair full-potential code. The induced drag characteristics of a typical transport wing were studied with Tranair, a full-potential method, and A502, a high-order linear panel method to investigate changes in lift distribution and span efficiency due to compressibility. Modeling the force-free wake is a nonlinear problem, even when the flow governing equation is linear. A novel method was developed for computing the force-free wake shape. This hybrid wake-relaxation scheme couples the well-behaved nature of the discrete vortex wake with viscous-core modeling and the high-accuracy velocity prediction of the high-order panel method. The hybrid scheme produced converged wake shapes that allowed accurate Trefftz-plane integration. An unusual split-tip wing concept was studied for exploiting nonlinear wake interaction to reduced induced drag. This design exhibits significant nonlinear interactions between the wing and wake that produced a 12% reduction in induced drag compared to an equivalent elliptical wing at a lift coefficient of 0.7. The performance of the split-tip wing was also investigated by wing tunnel experiments. Induced drag was determined from force measurements by subtracting the estimated viscous drag, and from an analytical drag-decomposition method using a wake survey. The experimental results confirm the computational prediction.

Smith, Stephen C.↗

NASA NTRS2002

Effects of Convective Transport of Solute and Impurities on Defect-Causing Kinetics Instabilities in Protein Crystallization

The objective of the proposed research is to obtain further insight into the onset and development of the defect-causing instabilities that anise due to the coupling of the bulk transport and nonlinear-interfacial kinetics during growth in the mixed regime, utilizing the reduction of the convective contribution to the bulk transport under microgravity. These studies will build upon the data on the effects of quantitative variations of the forced convection velocity on the averaged and time-dependent kinetic behavior of protein crystal growth systems that have recently been obtained in our laboratory.

Vekilov, Peter G.↗

NASA NTRS1988

Cooperative control of two arms in the transport of an inertial load in zero gravity

In designing a robot control system for dual arm configurations, the control engineer is faced with two challenges: to derive the equations of motion for a given situation, and to meet certain desired control requirements (for instance, minimum energy). The former may involve closed kinematic chains, such as the case when the two arms are grasping a common object. The latter usually involves nonlinear optimization. These issues are considered in the context of transporting an inertial load using two planar three-link arms. A generalized 'reduction transformation' is applied to the dynamics to remove the singularity in the system equations. A suboptimal minimum energy method is presented to reduce a difficult 12-state, six-control nonlinear optimization to two independent, nonconflicting suboptimizations. A simulation example is provided to illustrate the degree of energy reduction possible using the optimal arm torque distribution that was developed.

Carignan, Craig R.↗

NASA NTRS1995

Practical aspects of variable reduction formulations and reduced basis algorithms in multidisciplinary design optimization

This paper discusses certain connections between nonlinear programming algorithms and the formulation of optimization problems for systems governed by state constraints. The major points of this paper are the detailed calculation of the sensitivities associated with different formulations of optimization problems and the identification of some useful relationships between different formulations. These relationships have practical consequences; if one uses a reduced basis nonlinear programming algorithm, then the implementations for the different formulations need only differ in a single step.

Lewis, Robert Michael↗

NASA NTRS1983

Guaranteed robustness properties of multivariable, nonlinear, stochastic optimal regulators

The robustness of optimal regulators for nonlinear, deterministic and stochastic, multi-input dynamical systems is studied under the assumption that all state variables can be measured. It is shown that, under mild assumptions, such nonlinear regulators have a guaranteed infinite gain margin; moreover, they have a guaranteed 50 percent gain reduction margin and a 60 degree phase margin, in each feedback channel, provided that the system is linear in the control and the penalty to the control is quadratic, thus extending the well-known properties of LQ regulators to nonlinear optimal designs. These results are also valid for infinite horizon, average cost, stochastic optimal control problems.

Tsitsiklis, J. N.↗

NASA NTRS1984

Guaranteed robustness properties of multivariable nonlinear stochastic optimal regulators

Tsitsiklis, J. N.↗

NASA NTRS1996

Guidance of Nonlinear Nonminimum-Phase Dynamic Systems

The research work has advanced the inversion-based guidance theory for: systems with non-hyperbolic internal dynamics; systems with parameter jumps; and systems where a redesign of the output trajectory is desired. A technique to achieve output tracking for nonminimum phase linear systems with non-hyperbolic and near non-hyperbolic internal dynamics was developed. This approach integrated stable inversion techniques, that achieve exact-tracking, with approximation techniques, that modify the internal dynamics to achieve desirable performance. Such modification of the internal dynamics was used (a) to remove non-hyperbolicity which is an obstruction to applying stable inversion techniques and (b) to reduce large preactuation times needed to apply stable inversion for near non-hyperbolic cases. The method was applied to an example helicopter hover control problem with near non-hyperbolic internal dynamics for illustrating the trade-off between exact tracking and reduction of preactuation time. Future work will extend these results to guidance of nonlinear non-hyperbolic systems. The exact output tracking problem for systems with parameter jumps was considered. Necessary and sufficient conditions were derived for the elimination of switching-introduced output transient. While previous works had studied this problem by developing a regulator that maintains exact tracking through parameter jumps (switches), such techniques are, however, only applicable to minimum-phase systems. In contrast, our approach is also applicable to nonminimum-phase systems and leads to bounded but possibly non-causal solutions. In addition, for the case when the reference trajectories are generated by an exosystem, we developed an exact-tracking controller which could be written in a feedback form. As in standard regulator theory, we also obtained a linear map from the states of the exosystem to the desired system state, which was defined via a matrix differential equation.

Devasia, Santosh↗

NASA NTRS1989

The effect of Mach number on the stability of a plane supersonic wave

The influence of compressibility on the mechanisms governing the various stages of transition in a supersonic wake is investigated. Results from linear stability theory are used to provide physical insights into the observed reduction in growth rate at high Mach numbers. A newly developed hybrid algorithm is used to solve the compressible inviscid linear disturbance equations. Growth rates for both antisymmetric and symmetric modes of two-dimensional and oblique waves are computed for a wide range of Mach numbers. Results from two and three-dimensional direct numerical simulations of a forced compressible time-developing wake are presented in order to understand the nonlinear stages of transition at high Mach numbers. Observed nonlinear growth rate comparisons are made for wakes at two different Mach numbers. The reduction in growth rate at high Mach numbers is explained by examining contour plots of baroclinic torques and the product of dilatation and vorticity.

Chen, Jacqueline H.↗

NASA NTRS1993

Modelling chaotic vibrations using NASTRAN

Due to the unavailability and, later, prohibitive cost of the computational power required, many phenomena in nonlinear dynamic systems have in the past been addressed in terms of linear systems. Linear systems respond to periodic inputs with periodic outputs, and may be characterized in the time domain or in the frequency domain as convenient. Reduction to the frequency domain is frequently desireable to reduce the amount of computation required for solution. Nonlinear systems are only soluble in the time domain, and may exhibit a time history which is extremely sensitive to initial conditions. Such systems are termed chaotic. Dynamic buckling, aeroelasticity, fatigue analysis, control systems and electromechanical actuators are among the areas where chaotic vibrations have been observed. Direct transient analysis over a long time period presents a ready means of simulating the behavior of self-excited or externally excited nonlinear systems for a range of experimental parameters, either to characterize chaotic behavior for development of load spectra, or to define its envelope and preclude its occurrence.

Sheerer, T. J.↗

NASA NTRS1962

EFFECTS OF MODES OF INITIAL IMPERFECTIONS ON THE STABILITY OF CYLINDRICAL SHELLS UNDER AXIAL COMPRESSION

The effects of definite and "indefinite" initial imperfections on the buckling and post buckling behavior of an axially compressed cylindrical shell are analyzed by a nonlinear theory. The definite initial imperfections considered do not contribute to the reduction of the peak buckling load; while the "indefinite" imperfections, expressed in terms of a single factor introduced by Donnell 1 , cause a reduction in the buckling strength. The physical meaning of the imperfection factor, however, needs further clarification. Two theoretical buckling processes are found to be possible. In the early stage of buckling, the cylinder may deform with a comparatively large number of waves of small amplitudes or the cylinder may deform with a comparatively small number of waves of large amplitudes. Further theoretical and experimental studies of the effects of initial imperfections and the process of buckling are suggested.

AXIAL COMPRESSION↗

NASA NTRS1984

Rotordynamic Characteristics of the HPOTP (High Pressure Oxygen Turbopump) of the SSME (Space Shuttle Main Engine)

Rotational stability of turbopump components in the space shuttle main engine was studied via analysis of component and structural dynamic models. Subsynchronous vibration caused unacceptable migration of the rotor/housing unit with unequal load sharing of the synchronous bearings that resulted in the failure of the High Pressure Oxygen Turbopump. Linear analysis shows that a shrouded inducer eliminates the second critical speed and the stability problem, a stiffened rotor improves the rotordynamic characteristics of the turbopump, and installing damper boost/impeller seals reduces bearing loads. Nonlinear analysis shows that by increasing the "dead band' clearances, a marked reduction in peak bearing loads occurs.

Childs, D. W.↗

NASA NTRS1984

Linear distributed parameter systems - Closed-loop exponential stability with a finite-dimensional controller

Theoretical results are presented which characterize the linear distributed parameter system (DPS) which can be (exponentially) stabilized by a finite-dimensional controller. This characterization relies on stabilizing subspaces and the solvability of the nonlinear asymmetric Riccati equation. Also considered are connections with the usual model reduction approaches to finite-dimensional DPS controller design.

Balas, M. J.↗