Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Noise Attenuation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Aerodynamic and acoustic performance of high Mach number inlets

Experimental results were obtained for two types of high Mach number inlets, one with a translating centerbody and one with a fixed geometry (collapsing cowl) without centerbody. The aerodynamic and acoustic performance of these inlets was examined. The effects of several parameters such as area ratio and length-diameter ratio were investigated. The translating centerbody inlet was found to be superior to the collapsing cowl inlet both acoustically and aerodynamically, particularly for area ratios greater than 1.5. Comparison of length-diameter ratio and area ratio effects on performance near choked flow showed the latter parameter to be more significant. Also, greater high frequency noise attenuation was achieved by increasing Mach number from low to high subsonic values.

Lumsdaine, E.↗
NASA NTRS1977

Advanced turboprop technology development

The efficiency of high-speed turboprop propulsion systems is considered with emphasis on fuel savings. Specific topics discussed include: (1) high efficiency and low noise of propeller design; (2) fuselage noise attenuation; (3) propeller and gear box maintenance; and (4) engine-airframe integration.

Dugan, J. F.↗
NASA NTRS1977

Advanced turboprop technology development

In order for new short-medium range transports to offer significantly lower operating costs than potential derivatives of current designs using advanced technology, the efficiency improvements of high-speed turboprop propulsion systems may be required. Recent studies indicate that the fuel savings of advanced turboprop aircraft appears to be 10 to 20 percent relative to equivalent technology turbofan aircraft. These fuel savings are certainly large enough to warrant further research to establish the viability of turboprop transport aircraft. The studies have identified the technology requirements in propeller design for high efficiency and low noise, fuselage noise attenuation, propeller and gear box maintenance, and engine-airframe integration. This paper presents a review of present research in each of these areas and describes the future plans for continued development of the technology for advanced turboprop transport aircraft.

Dugan, J. F.↗
NASA NTRS1981

Acoustic transmission in lined flow ducts - A finite element eigenvalue problem

The problem of acoustical transmission in lined ducts with subsonic mean flow is of considerable practical interest in the context of fan noise attenuation in the ducted inlet regions of turbofan aircraft engines. If nonaxisymmetric liners are present, a loss of axial symmetry results, and the study of acoustic transmission involves the solution of a full two-dimensional eigenvalue problem. The reported investigation is concerned with such an eigenvalue problem. The employed method of solution is effectively a two-dimensional analog of an approach considered by Astley and Eversman (1979). The approach makes use of a Galerkin Finite Element Method whereby the weighting and basis functions are generated automatically by the discretization.

Astley, R. J.↗
NASA NTRS1983

Inverted velocity profile semi-annular nozzle jet exhaust noise experiments

Experimental noise data are shown for a conical nozzle with a semi-annular secondary flow passage having secondary to primary velocity ratios ranging from 1.0 to 1.4. Spectral data are presented at different directivity angles in the flyover plane with the semi-annular flow passage located either on the same side or opposite side relative to an observer. A 10.0 cm diameter primary conical nozzle was used with a 2.59 cm and 5.07 cm wide annular gap secondary nozzle. Similar trends were observed for both nozzle configurations. In general, near the peak noise location and at velocity ratios greater than 1.0, noise levels were larger on the side where the secondary passage was closest to an observer. At velocity ratios near 1.0 the opposite was true. When compared to predicted noise levels for a conical nozzle alone operating at the same ideal thrust, the semi-annular configuration showed no benefit in terms of noise attenuation.

Goodykoontz, J. H.↗
NASA NTRS1984

Study of double wall panels for use in propeller driven aircraft

Propeller driven aircraft have exhibited high levels of interior noise. Most absorption materials are not effective at low frequencies where maximum noise levels occur. Two panels separated by an air gap are suggested as an alternative means of noise attenuation. This design produces an impedance mismatch where a sound wave travels backwards to the source. The higher the impedance, the higher the reflected soundwave intensity. Two aluminum panels with helium in between and two panels with one being perforated were investigated. Helium increases the transmission loss because of a greater impedance mismatch than air. The transmission loss of the unperforated panel is higher throughout the frequency range tested.

Atwal, M.↗
NASA NTRS1986

Design requirements for the NASA Langley supersonic low-disturbance wind tunnel

The high intensity, high frequency acoustic disturbances that cause large adverse boundary layer transition effects on test models in conventional supersonic wind tunnels consist of finite length wavelets radiating from eddies in the turbulent boundary layers of the wind tunnel walls. NASA Langley has undertaken 'quiet' supersonic tunnel research that demonstrates the ability to maintain laminarity at high unit Reynolds numbers on limited upstream regions of the nozzle wall boundary layers in small, Mach 3.0, 3.5, and 5.0 pilot tunnels. The high level acoustic disturbances are then eliminated, and the transition Reynolds numbers measured on cones approach those for atmospheric flight. Attention is presently given to the design requirements that can be extrapolated from these results for a large wind tunnel facility; high quality air filtering, noise attenuation, nozzle coordinate accuracy, and surface finish, are quantified with pilot tunnel data.

Beckwith, I. E.↗
NASA NTRS1988

Inlet development for the NFAC 80- by 120-foot indraft wind tunnel

This paper describes the inlet design requirements of the National Full-Scale Aerodynamic Complex (NFAC), a closed-loop 4-by-80 foot wind tunnel and indraft 80-by-120 foot wind tunnel. The requirements are based upon desired test section flow quality, atmospheric wind isolation, and noise attenuation. An aerodynamic design study of the inlet treatment is described along with the analysis method and the small-scale testing program used. Measurements taken in the full-scale facility are presented, and the flow quality is summarized. The results are compared with theoretical predictions and small-scale model results.

Van Aken, Johannes M.↗
NASA NTRS1999

Titanium Aluminide Applications in the High Speed Civil Transport

It is projected that within the next two decades, overseas air travel will increase to over 600,000 passengers per day. The High Speed Civil Transport (HSCT) is a second-generation supersonic commercial aircraft proposed to meet this demand. The expected fleet of 500 to 1500 aircraft is required to meet EPA environmental goals; the HSCT propulsion system requires advanced technologies to reduce exhaust and noise pollution. A part of the resultant strategy for noise attenuation is the use of an extremely large exhaust nozzle. In the nozzle, several critical components are fabricated from titanium aluminide: the divergent nap uses wrought gamma; the nozzle sidewall is a hybrid fabrication of both wrought gamma face sheet and cast gamma substructure. This paper describes the HSCT program and the use of titanium aluminide for its components.

Bartolotta, Paul A.↗
NASA NTRS1999

High Temperature Acoustic Liner Technology

This paper describes work currently in progress at Langley on liner concepts that employ structures that may be suitable for broadband exhaust noise attenuation in high speed flow environments and at elevated temperatures characteristic of HSCT applications. Because such liners will need to provide about 10 dB suppression over a 2 to 3 octave frequency range, conventional single-degree-of-freedom resonant structures will not suffice. Bulk absorbers have the needed broadband absorption characteristic; however, at lower frequencies they tend to be inefficient.

Parrott, Tony L.↗
NASA NTRS2000

Three-Dimensional Nacelle Aeroacoustics Code With Application to Impedance Education

A three-dimensional nacelle acoustics code that accounts for uniform mean flow and variable surface impedance liners is developed. The code is linked to a commercial version of the NASA-developed General Purpose Solver (for solution of linear systems of equations) in order to obtain the capability to study high frequency waves that may require millions of grid points for resolution. Detailed, single-processor statistics for the performance of the solver in rigid and soft-wall ducts are presented. Over the range of frequencies of current interest in nacelle liner research, noise attenuation levels predicted from the code were in excellent agreement with those predicted from mode theory. The equation solver is memory efficient, requiring only a small fraction of the memory available on modern computers. As an application, the code is combined with an optimization algorithm and used to reduce the impedance spectrum of a ceramic liner. The primary problem with using the code to perform optimization studies at frequencies above I1kHz is the excessive CPU time (a major portion of which is matrix assembly). The research recommends that research be directed toward development of a rapid sparse assembler and exploitation of the multiprocessor capability of the solver to further reduce CPU time.

Watson, Willie R.↗
NASA NTRS2006

HSR Overview

The leading Aeronautics program within NASA is the High Speed Research Program (HSR). The HSR program's highest priorities are high pay-off technologies for airframe and propulsion systems required for a high speed civil transport (HSCT). These priorities have been developed collaboratively with NASA, FAA and the US Industry (Boeing-McDonnell Douglas, Pratt & Whitney and General Electric). Phase one of the HSR program started on 1990, and concentrated on the environmental challenges of minimizing NOx and noise. The first program goal is to reduce the NOx emission index to less than 5 (Concord NOx index is 20 and is unacceptable), in order to have little impact on the earth's ozone layer. The second goal is to reduce noise levels to FAR Stage 3 (or better), comparable to those of subsonic aircraft (far below the Concorde noise levels that require exemptions form less stringent standards). This requirement greatly impacts the nozzle design increasing its length and complexity and poses unique sealing challenges. Phase two started in 1993 and initiated work on the technologies required for an economical HSCT. Materials technologies under development include a ceramic-matrix-composite combustion liner, lightweight materials for the nozzle, as well long-life turbomachinery disk and blade alloys. Other required materials are being developed under the DOD-IHPTET program, where there is close cooperation. Economic goals translate into the development of technologies for tri-class service, 5000 nautical mile range aircraft with a ticket price no more than 20% over the subsonic ticket price. The potential market could be as large as 1500 aircraft, according to a Boeing study. Technology alone will not enable this airplane, yet without enabling technologies "on the shelf", it will not occur. The HSCT engine will be the largest engine ever built and operate at maximum conditions for long periods of time posing a number of challenges. The HSR engine mission requires that rotating equipment stay at take-off condition temperatures for hours not minutes per flight. Hence rotating equipment and seals must operate for many thousands of hours at extreme temperatures. It is anticipated that the nozzle will be 12 feet long and roughly 4 ft. by 5 ft. in cross-section with a nominal airflow of 800 lbs/sec. The complex function of the nozzle (including an ejector for noise attenuation) combined with long life place new demands on nozzle seal design. Three inlet configurations are under consideration with attendant sealing challenges, as will be illustrated herein. Four of these engines are required to propel a 5000 nautical mile class vehicle which demand that component reliability be at the highest possible level. In response, an HSR seals session was implemented as a part of the 1997-Seals and Secondary Flow Workshop. Overview presentations were given for each of the following areas: inlet, turbomachinery, combustor and nozzle. The HSCT seal issues center on durability and efficiency of rotating equipment seals (including brush seals), structural seals (including rope seals and other advanced concepts), and high-speed bearing and sump seals. Tighter clearances, propulsion system size and thermal requirements represent extremes that challenge the component designers. This document provides an initial step toward defining HSR seal needs. The overview for HSR seal designs includes, defining seal objectives, summarizing sealing and materials requirements, presenting relevant seal cross-sections, and identifying technology needs for the HSR office.

Hendricks, R. C.↗
NASA NTRS1994

Sound suppression mixer

A gas turbine engine flow mixer includes at least one chute having first and second spaced apart sidewalls joined together at a leading edge, with the sidewalls having first and second trailing edges defining therebetween a chute outlet. The first trailing edge is spaced longitudinally downstream from the second trailing edge for defining a septum in the first sidewall extending downstream from the second trailing edge. The septum includes a plurality of noise attenuating apertures.

Brown, William H.↗
NASA NTRS2011

Communal Sensor Network for Adaptive Noise Reduction in Aircraft Engine Nacelles

Emergent behavior, a subject of much research in biology, sociology, and economics, is a foundational element of Complex Systems Science and is apropos in the design of sensor network systems. To demonstrate engineering for emergent behavior, a novel approach in the design of a sensor/actuator network is presented maintaining optimal noise attenuation as an adaptation to changing acoustic conditions. Rather than use the conventional approach where sensors are managed by a central controller, this new paradigm uses a biomimetic model where sensor/actuators cooperate as a community of autonomous organisms, sharing with neighbors to control impedance based on local information. From the combination of all individual actions, an optimal attenuation emerges for the global system.

Jones, Kennie H.↗
NASA NTRS2013

The Aerodynamic Performance of an Over-the-Rotor Liner With Circumferential Grooves on a High Bypass Ratio Turbofan Rotor

While liners have been utilized throughout turbofan ducts to attenuate fan noise, additional attenuation is obtainable by placing an acoustic liner over-the-rotor. Previous experiments have shown significant fan performance losses when acoustic liners are installed over-the-rotor. The fan blades induce an oscillating flow in the acoustic liners which results in a performance loss near the blade tip. An over-the-rotor liner was designed with circumferential grooves between the fan blade tips and the acoustic liner to reduce the oscillating flow in the acoustic liner. An experiment was conducted in the W-8 Single-Stage Axial Compressor Facility at NASA Glenn Research Center on a 1.5 pressure ratio fan to evaluate the impact of this over-the-rotor treatment design on fan aerodynamic performance. The addition of a circumferentially grooved over-the-rotor design between the fan blades and the acoustic liner reduced the performance loss, in terms of fan adiabatic efficiency, to less than 1 percent which is within the repeatability of this experiment.

Bozak, Richard F.↗
NASA NTRS2014

Sound Transmission Loss Through a Corrugated-Core Sandwich Panel with Integrated Acoustic Resonators

The goal of this study is to better understand the effect of structurally integrated resonators on the transmission loss of a sandwich panel. The sandwich panel has facesheets over a corrugated core, which creates long aligned chambers that run parallel to the facesheets. When ports are introduced through the facesheet, the long chambers within the core can be used as low-frequency acoustic resonators. By integrating the resonators within the structure they contribute to the static load bearing capability of the panel while also attenuating noise. An analytical model of a panel with embedded resonators is derived and compared with numerical simulations. Predictions show that acoustic resonators can significantly improve the transmission loss of the sandwich panel around the natural frequency of the resonators. In one configuration with 0.813 m long internal chambers, the diffuse field transmission loss is improved by more than 22 dB around 104 Hz. The benefit is achieved with no added mass or volume relative to the baseline structure. The embedded resonators are effective because they radiate sound out-of-phase with the structure. This results in destructive interference, which leads to less transmitted sound power.

Schiller, Noah H.↗
NASA NTRS2013

The Aerodynamic Performance of an Over-The-Rotor Liner with Circumferential Grooves on a High Bypass Ratio Turbofan Rotor

While liners have been utilized throughout turbofan ducts to attenuate fan noise, additional attenuation is obtainable by placing an acoustic liner over-the-rotor. Previous experiments have shown significant fan performance losses when acoustic liners are installed over-the-rotor. The fan blades induce an oscillating flow in the acoustic liners which results in a performance loss near the blade tip. An over-the-rotor liner was designed with circumferential grooves between the fan blade tips and the acoustic liner to reduce the oscillating flow in the acoustic liner. An experiment was conducted in the W-8 Single-Stage Axial Compressor Facility at NASA Glenn Research Center on a 1.5 pressure ratio fan to evaluate the impact of this over-the-rotor treatment design on fan aerodynamic performance. The addition of a circumferentially grooved over-the-rotor design between the fan blades and the acoustic liner reduced the performance loss, in terms of fan adiabatic efficiency, to less than 1% which is within the repeatability of this experiment.

Bozak, Rick↗
NASA NTRSDate not supplied

Development of Acoustic Mufflers for Cabin Noise Reduction in Orion Spacecraft

Controlling cabin acoustic noise levels in the Crew Module (CM) of the Orion spacecraft is critical to ensure adequate speech intelligibility, to avoid fatigue, and prevent any possibility of temporary and permanent hearing loss to the crew. The primary source of cabin noise for the on-orbit phase of the mission is from the Environmental Control and Life Support System (ECLSS) which recycles and conditions breathing air and maintains cabin pressurization through its duct network and components. Unfortunately, as a side effect, noise from the ECLSS fans propagates through theses ducts and emanate into the cabin habitable volume via the ECLSS inlet and outlets. To mitigate excessive duct-borne noise, two ECLSS mufflers have been designed to provide significant acoustic transmission loss (TL) so that the cabin noise requirements can be met. Each muffler is meant to be installed in the ducting of the ECLSS air inlet and outlet sides, respectively. Packaging constraints and tight volume requirements necessitated the mufflers to be of complex geometry and compatible with the bends of the ECLSS duct layout. To design and characterize the acoustic performance of the inlet and outlet mufflers, computational acoustic models were developed using the Finite Element Method (FEM) with 𝑤𝑎𝑣𝑒଺ vibroacoustic software. Characterization of the acoustic material and perforations in the mufflers were addressed with poroelastic theory. Once the mufflers were designed on paper and its TL predicted, prototypes of these mufflers were created using additive manufacturing. The muffler prototypes were subsequently tested for acoustic TL in the laboratory with various con-figurations of acoustic materials. Comparing the analytical predictions to the test performance yielded excellent correlation for acoustic TL and demonstrated significant broadband noise attenuation. The ECLSS mufflers are currently scheduled to be installed on the Artemis II Crew Module (CM) of the Orion spacecraft and will provide significant cabin comfort to crew during the mission.

Indranil Dandaroy↗