Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ni dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Decoupling the degradation factors of Ni-rich NMC/Li metal batteries using concentrated electrolytes

Battery degradation results from multiple factors that usually correlate with each other. Electrochemical corrosion of the current collector is one of the main reasons for battery failure, leading to poor internal electrical contact and the dissolution of harmful ions into electrolytes. This phenomenon is especially evident in lithium bistrifluoromethanesulfonimidate (LiTFSI)-based electrolytes, although they have many advantages over conventional lithium hexafluorophosphate (LiPF 6 )-based electrolytes, such as low viscosity, good thermal stability, and stable to water. Recently, highly concentrated electrolytes are found hopeful of inhibiting aluminum's corrosion and boosting new electrolyte development. Here we discuss the solvation structures of liquid electrolytes and decouple the degradation mechanisms of using LiTFSI-based electrolytes in Li(Ni 0.8 Co 0.1 Mn 0.1 )O 2 /Li metal batteries. The results suggest although concentrated electrolytes inhibit the Al corrosion, the growth of lithium dendrites and the protection of the cathode-electrolyte interphase are not significantly improved. Furthermore, this paper provides a paradigm to evaluate the performance of electrolytes comprehensively.

25 ENERGY STORAGE↗
DOE OSTI2022

Characterization of Contaminants and Mobility in WMA A-AX Boreholes D0006 and D0008

This study was initiated to determine if subsurface contaminants in the A-AX vadose zone at the Hanford site (boreholes D0006 and D0008) caused corrosion of nearby stainless steel well casings (299-E-24-19, 299-E25-46, and 299-E25-236) and, based on the type and distribution of contaminants, determine if contaminants are from one or more sources including a) the A-104 and/or A-105 tanks, b) the 242A evaporator, and c) the 200-E-286 ditch. A tiered approach was used for characterizing contaminants in vadose zone sediments starting with mobile and total contaminant concentrations (Tier 1), characterizing contaminant speciation (Tier 2), and measuring contaminant leaching (Tier 3). Total and mobile contaminant measurements at seven depths showed elevated sulfate and nitrate in all samples (130 to 280 ft depth), elevated chloride in five depths, and no elevated radionuclides except I-129 in D0006 at 206 to 208 ft depth. If these contaminants were initially acidic, stainless-steel corrosion would occur. However, because sediments likely have a high acid neutralization capacity, an acidic spill would have been neutralized within tens of feet, so casing corrosion would likely occur in shallow sediments. GEL labs data also shows low (but above natural) chromate from shallow to 170 ft depth, then higher chromate to 280 ft, suggesting a surface Cr spill or casing corrosion. GEL labs data also showed evidence of more than one plume, with deep nitrate, sulfate, and chloride migration, but only shallow tritium migration. Tritium should migrate nearly unretarded in the subsurface like nitrate and chloride. Elevated aqueous cations and anions in the D0006 206 to 208' depth pore water (SO 4 2- , NO 3 - , Na + , K + , Ca 2+ , Mg 2+ , Si) could be the result of acid disposal and calcite dissolution at shallow depth, with deeper migration of SO 4 2- , NO 3 - from acids and Ca 2+ and Mg 2+ from calcite. Elevated Si (160 mg/L) indicates dissolution of clays or other silicates, which can also occur in acids. Acid extractable metals did show elevated Cr (but not Fe, Ni, Mo, and Mn) above natural levels, which may indicate stainless-steel well corrosion or transport of metals from a shallow spill. The elevated I-129 in D0006 at 206 to 208' depth was low with 0.34 μg/g in pore water and 1.5 μg/g total extractable I-129 in the sediment, which indicates significant fraction of I-129 was bound in one or more precipitates. Although total I-129 was below detection limits in most extractions due to high molybdate interference, I-127 analysis provided some insight into potential precipitate phases. Total I-127 was mainly extracted by acetate or acetic acid (67%), which may be iodine in calcite. Inorganic carbon measurement identified 1.65% calcite, and total organic carbon (TOC) was below detection limits, so iodine was not associated with organic matter. Nearly all the I-127 was present as iodide. In 1-D leach experiments, I-127 as iodide leached from the sediment within 2 pore volumes. Due to high and dynamic molybdate leaching from the sediment and interference with I-129 analysis, there were few quantifiable I-129 measurements. The calculated molybdate release rates from the sediment suggested Mo was being released from the same precipitate phase, such as molybdate incorporated into calcite. Overall, because there was little radioactive contamination measured in D0006 and D0008 boreholes, potential releases from A-104 and A-105 did not reach this location south of the A tank farm. Elevated cations and anions found in D0006 and D0008 at depth as the result of acidic disposal could cause shallow stainless steel casing corrosion. The nearby 242A evaporator generally contained alkaline waste and tritium, but the nearby 200-E-286 ditch generally contained high Cl - liquid effluent, so these are unlikely to be acidic sources.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRSDate not supplied

Olivine Dissolution and Formation of Secondary phases in Ultramafic Soils

Introduction: Olivine has been proposed as an indicator for the duration of water-rock interaction within Martian rocks and sediments [1-3]. The use of olivine as a mineralogical indicator for past aqueous alteration on Mars requires interpretation of a complex combination of factors including pH, temperature, and composition [5,6]. Here, we examine the persistence of natural olivine within terrestrial ultramafic soils (Fe/Mg-rich, Al-poor) developing under different climatic conditions and the incipient dissolution of emplaced forsterite (Fo) and fayalite (Fa) surfaces to investigate environmental effects on incipient olivine dissolution, olivine persistence in soils, and formation of secondary phases. Methods: Field Sites. We examined olivine weathering and secondary material formation in ultramafic soils at 6 sites in the Klamath Mountains (KM) of northern California with a mean annual temperature of ~12.8℃ and precipitation of ~55.7-95.4 cm/year [7], and soil pH of ~6.5-7.3; 4 sites in the Tablelands (TB) of Newfoundland, Canada with a mean annual temperature of <3.9℃ and precipitation of ~120.0 cm/year [8], and soil pH of ~7.7; and at 3 sites at Pickhandle Gulch (PG), Nevada with a mean annual temperature of ~14.4℃ and precipitation of ~14.1 cm/year [7], and soil pH of ~8.5. Sampling sites span an age range of ~12.1-50+ kya in the Klamath Mountains [9,10] and ~13-30 kya in the Tablelands [11]. Pickhandle Gulch sites are undated. Parent Material and Soil Analyses. Polished thin sections of bulk soil prepared by Wagner Petrographic, Inc were carbon-coated and analyzed on a JEOL 2100 SEM in back-scattered electron mode in the EMIL lab at UNLV and at the 13-ID-E synchrotron beamline at Argonne National Laboratory using µXRF, µXRD, and XAS. Soil and parent material samples were powdered in a Fritsch pulverisette and analyzed by XRD and soil by VNIR. Soil preparation is further described in [12]. Disk Preparation, Burial, and Collection. Fo disks were cut from a column prepared via hot-pressing and Fa disks by sintering synthetic fayalite powder, see [13] for detail. Disks were polished to a 0.25-micron level with diamond grit. Disks were buried in 3 KM soils, 4 TB soils, and 3 PG soils, collected after exactly 365 days, and washed gently with 100% reagent grade ethanol to remove potential adhered soil material. Weathered disks and soil samples were stored in a -20℃ freezer until analysis. Unaltered control disks prepared identically to the buried disks were stored at -20℃ for the duration of the experiment. Disk Analyses. One Fo and Fa disk from each climate zone was analyzed on a variable pressure Zeiss Supra 40VP SEM at Northern Arizona University. A separate Fo and Fa disk from each climate zone was analyzed by XPS using a Physical Electronics VersaProbe II at the Penn State Univ. Materials Characterization Lab after a Na-dodecyl sulfate wash and ozonation to remove carbon contamination as in [14]. VNIR measurements were conducted at Johnson Space Center using an ASD FieldSpec3 under ambient lab conditions on a separate Fo and Fa disk from each climate zone. One separate Fo and Fa control sample was analyzed for each technique for comparison with weathered samples. XPS uncertainty was determined from 5 repeat measurements on controls. Results: Bedrock and Soil Results Olivine is present in the parent material in the KM and TB. Olivine is found in ~12.1 ka KM soils but is absent from all older soils, while persisting into the oldest (>20 ka) TB soil (Figure 1). In both locations, olivine is found as cores surrounded by a serpentine rind (Figure 2). VNIR spectra from the analyzed soils possess strong OH-associated spectral features at ~2.33 µm indicating the presence of Mg-rich phyllosilicates as well as ferric-oxide features at ~0.92 µm in the KM (Figure 3). Primary crystalline silicate grains mostly incorporate Fe2+, while poorly crystalline weathering rinds are best fit by ferric oxide XAS standards (Figure 4). µXRF also shows that Fe and Ni concentrate in weathering rinds and Cr remains within interior silicate grains (Figure 4). Buried Sample Results All Fo surfaces exhibited formation of dissolution features including shallow pitting not observed on controls. Dissolution features were most visually widespread on the KM disk (Figure 5). Leaching of Mg from KM and TB Fo disks was evident from <1.6 Mg/Si ratios measured by XPS (Figure 6). Fe-rich precipitates in SEM (Figure 5) and Fe presence in XPS scans (Figure 6) indicate Fe deposition onto KM and TB Fo disk surfaces. The appearance of a spectral feature at 0.55 µm in the VNIR spectra from the TB Fo suggests this Fe is ferric (Figure 7). The PG Fo appears least altered, with minimal formation of dissolution features in SEM (Figure 5), a Mg/Si ratio inconsistent with leaching (~2) (Figure 6), and VNIR spectra almost identical to the control sample. Analysis of Fa surfaces is ongoing. The higher temperatures and more acidic pH in the KM soils likely drive the faster dissolution of the Fo disks described above. While the TB soils experience greater precipitation than in the KM, the cooler temperatures and more basic soil pH facilitate observable but more limited alteration. The dry climate and basic soil pH at PG lead to minimal dissolution of the PG disk surfaces.

A D Feldman↗
DOE OSTI2021

A Cobalt– and Manganese–Free High–Nickel Layered Oxide Cathode for Long–Life, Safer Lithium–Ion Batteries

High-nickel LiNi 1–x–y Mn x Co y O 2 and LiNi 1–x–y Co x Al y O 2 cathodes are receiving growing attention due to the burgeoning demands on high-energy-density lithium-ion batteries. The presence of both cobalt and manganese in them, however, triggers multiple issues, including high cost, high toxicity, rapid surface deterioration, and severe transition-metal dissolution. Herein, a Co- and Mn-free ultrahigh-nickel LiNi 0.93 Al 0.05 Ti 0.01 Mg 0.01 O 2 (NATM) cathode that exhibits 82% capacity retention over 800 deep cycles in full cells, outperforming two representative high-Ni cathodes LiNi 0.94 Co 0.06 O 2 (NC, 52%) and LiNi 0.90 Mn 0.05 Co 0.05 O 2 (NMC, 60%) is presented. It is demonstrated that a titanium-enriched surface along with aluminum and magnesium as the stabilizing ions in NATM not only ameliorates unwanted side reactions with the electrolyte and structural disintegrity, but also mitigates transition-metal dissolution and active lithium loss on the graphite anode. As a result, the graphite anode paired with NATM displays an ultrathin (≈8 nm), monolayer anode-electrolyte interphase architecture after extensive cycling. Furthermore, NATM displays considerably enhanced thermal stability with an elevated exothermic temperature (213 °C for NATM vs 180 and 190 °C for NC and NMC, respectively) and remarkably reduced heat release. This work sheds light on rational compositional design to adopt ultrahigh-Ni cathodes in lithium-based batteries with low cost, long service life, and improved thermal stability.

25 ENERGY STORAGE↗
DOE OSTI2023

Evaluation of Corrosion Behavior of Various Fe- and Ni-Based Alloys in Molten Li 2 BeF 4 (FLiBe)

Reliable performance of structural alloys is essential for the successful implementation of Generation-IV fluoride salt–cooled high-temperature reactors (FHRs). Most FHR designs are considering molten salt (2LiF-BeF 2 ), or FLiBe, as a primary coolant or fuel carrier. The main corrosion mechanism for alloys exposed to molten fluoride salts is the selective dealloying of active alloying elements. Alloy composition has a significant effect on their high-temperature mechanical properties, but also affects their corrosion behavior. Although Hastelloy-N and its variants show good corrosion resistance compared to higher Cr-containing Ni- or Fe-based alloys, the mechanical properties of these alloys degrade quickly at temperatures above ~600°C. Twelve Ni-based or Fe-based alloys were selected due to their high temperature stability or their low Cr alloy composition and tested for their corrosion behavior in FLiBe. The results show that the mode and the extent of alloy degradation by selective dissolution mechanism corelates well with the overall alloy composition, and not just the concentration of active elements. It was found that there was good correlation between weight loss of the tested alloys and the ratio of major active elements (Cr, Mn) to that of the more noble alloying elements (Ni, Mo).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Cryo-based Structural Characterization and Growth Model of Salt Film on Metal

Metal salt films play a critical role in high rate dissolution processes such as within an active pit. However, structural and compositional characterization of salt films is challenging owing to the dynamic nature of the dissolving interface. Here, the salt film formed on SS304 one-dimensional artificial pit surface was directly characterized using flash freezing and cryo-based focused ion beam/scanning electron microscopy. The salt film exhibits a porous structure. Ni is co-located with Fe in the salt film, indicating the formation of co-precipitated salt containing Fe2+ and Ni2+. Additionally, a salt film growth model is presented based on ion transport.

Salt film, Pitting corrosion, Cryogenic, Cryo-FIB/↗
DOE OSTI2023

Electrolyte Study for High-Nickel LiNi 0.9 Mn 0.05 Co 0.05 O 2 Cathodes

With an increasing demand for intermittent renewable energy and electric vehicles, it is imperative to develop lithium-ion batteries with Earth-abundant cathode materials. Cobalt (Co) is preferred to be kept at a minimum because of its high cost and limited mining options, yet it has played an essential role in the high-performance transition metal oxides (TMOs). Herein, we report work from Argonne National Laboratory, conducted under the U.S. DoE's Vehicle Technologies Office, Deep Dive consortium on Next-Generation Cathodes, to optimize electrolytes for LiNi 0.9 Mn 0.05 Co 0.05 O 2 . LiNi 0.9 Mn 0.05 Co 0.05 O 2 is a high-Ni TMO benchmark as it outperforms most other TMOs under standard cycling conditions. In this study, we use the figure-of-merit approach to optimize electrolytes for this novel cathode material. Dual-salt carbonate electrolytes containing lithium difluorooxyphosphate and hexafluorophosphates were found to be the best for capacity retention and slowing the impedance rise. Importantly, transition metal dissolution and lithium inventory losses in the solid electrolyte interface were found to be the major causes for capacity fade.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Structural and Electrochemical Impacts of Mg/Mn Dual Dopants on the LiNiO 2 Cathode in Li-Metal Batteries

Doping chemistry has been regarded as an efficient strategy to overcome some fundamental challenges facing the “no-cobalt” LiNiO 2 cathode materials. By utilizing the doping chemistry, we evaluate the battery performance and structural/chemical reversibility of a new no-cobalt cathode material (Mg/Mn-LiNiO 2 ). The unique dual dopants drive Mg and Mn to occupy the Li site and Ni site, respectively. We report the Mg/Mn-LiNiO 2 cathode delivers smooth voltage profiles, enhanced structural stability, elevated self-discharge resistance, and inhibited nickel dissolution. As a result, the Mg/Mn-LiNiO 2 cathode enables improved cycling stability in lithium metal batteries with the conventional carbonate electrolyte: 80% capacity retention after 350 cycles at C /3, and 67% capacity retention after 500 cycles at 2 C (22 °C). We then take the Mg/Mn-LiNiO 2 as the platform to investigate the local structural and chemical reversibility, where we identify that the irreversibility takes place starting from the very first cycle. The highly reactive surface induces the surface oxygen loss, metal reduction reaching the subsurface, and metal dissolution. Our data demonstrate that the dual dopants can, to some degree, mitigate the irreversibility and improve the cycling stability of LiNiO 2 , but more efforts are needed to eliminate the key challenges of these materials for battery operation in the conventional carbonate electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2023

Stabilizing Ni-rich layered cathode for high-voltage operation through hierarchically heterogeneous doping with concentration gradient

High-nickel LiNi x Mn y Co 1-x-y O 2 (NMC) cathodes have demonstrated superior energy density, yet their stability is compromised under high voltage conditions. To address this, here we propose a strategy of heterogeneous doping with a concentration gradient, specifically through Sr–Zr co-modification. We synthesized Ni-rich NMC particles featuring several micron-sized secondary particles composed of micron-sized primary grains. This design aims to harness the structural robustness of single-crystalline grains and the favorable diffusion kinetics of polycrystalline secondary particles. Systematic characterization using a combination of electrochemical measurements and synchrotron analytics reveals an intriguing pattern of hierarchically heterogeneous Sr–Zr co-doping. It demonstrates a depth-dependent concentration gradient at the secondary particle level and competing dopant segregation over the buried grain boundaries. This unique characteristic creates opportunities for enhancing battery performance, particularly by optimizing precursors and implementing advanced modulation techniques. We also investigate the dissolution and precipitation of the cathode's transition metal cations upon high-voltage cycling. These insights suggest that a tailored compositional variation can be a viable approach to effectively design the next-generation high-Ni NMC cathode materials for high-voltage lithium batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In Situ Construction of Uniform and Robust Cathode–Electrolyte Interphase for Li-Rich Layered Oxides

The high-energy-density Li-rich layered oxides (LLOs) as promising cathodes for Li-ion batteries suffer from the dissolution of transition metals (especially manganese) and severe side reactions in conventional electrolytes, which greatly deteriorate their electrochemical performance. Herein, an in situ “anchoring + pouring” synergistic cathode-electrolyte interphase (CEI) construction is realized by using 1,3,6-hexanetricarbonitrile (HTCN) and tris(trimethylsilyl) phosphate (TMSP) electrolyte additives to alleviate the challenges of an LLO (Li 1.13 Mn 0.517 Ni 0.256 Co 0.097 O 2 ). HTCN with three nitrile groups can tightly anchor transition metals by coordinative interaction to form the CEI framework, and TMSP will electrochemically decompose to reshape the CEI layer. The uniform and robust in situ constructed CEI layer can suppress the transition metal dissolution, shield the cathode against diverse side reactions, and significantly improve the overall electrochemical performance of the cathode with a discharge voltage decay of only 0.5 mV/cycle -1 . Further investigations based on a series of experimental techniques and theoretical calculations have revealed the composition of in situ constructed CEI layers and their distribution, including the enhanced HTCN anchoring effect after lattice densification of LLOs. Finally, this study provides insights into the in situ CEI construction for enhancing the performance of high-energy and high-voltage cathode materials through effective, convenient and economical electrolyte approaches.

25 ENERGY STORAGE↗
DOE OSTI2020

Potential-pH diagrams considering complex oxide solution phases for understanding aqueous corrosion of multi-principal element alloys

The potential-pH diagram, a graphical representation of the thermodynamically predominant reaction products in aqueous corrosion, is originally proposed for the corrosion of pure metals. The original approach only leads to stoichiometric oxides and hydroxides as the oxidation products. However, numerous experiments show that non-stoichiometric oxide scales are prevalent in the aqueous corrosion of alloys. In the present study, a room temperature potential-pH diagram considering oxide solid solutions, as a generalization of the traditional potential-pH diagram with stoichiometric oxides, is constructed for an FCC single-phase multi-principal element alloy (MPEA) based on the CALculation of PHAse Diagram method. The predominant reaction products, the ions in aqueous solution, and the cation distribution in oxides are predicted. The oxide solid solution is stabilized by the mixing free energy (or mixing entropy) and the stabilizing effect becomes more significant as the temperature increases. Consequently, solid solution oxides are stable in large regions of the potential-pH diagram and the mixing free energy mostly affects the equilibrium composition of the stable oxides, while the shape of stable regions for oxides is mostly determined by the structure of the stable oxides. Agreements are found for Ni 2+ , Fe 2+ , and Mn 2+ between the atomic emission spectroelectrochemistry measurements and thermodynamic calculations, while deviations exist for Cr 3+ and Co 2+ possibly due to surface complexation with species such as Cl - and the oxide dissolution. By incorporating the solution models of oxides, the current work presents a general and more accurate way to analyze the reaction products during aqueous corrosion of MPEAs.

Materials Science↗
DOE OSTI2020

Generalized synthesis of high surface area mesoporous metal titanates as efficient heterogeneous catalysts

A novel metal dissolution coupled with reverse micelle formation approach is used as a generalized synthesis method for a series of high surface area metal titanates where the metals used are Bi, Mg, V, Mn, Fe, Co, Ni, Cu, Zn, Mo, W, and Ce. This study reports the highest surface areas published so far. The homogeneous distributions of the metals and titanium are observed in SEM-EDX and TEM mapping. The synthesized materials were comprehensively characterized using PXRD, Raman, nitrogen adsorption isotherms, SEM; EDX, TEM, TEM mapping, TGA, and XPS. The green catalytic oxidation of aniline to nitrosobenzene occurs within 30 min at room temperature when mesoporous W/Ti binary metal oxide is used as the catalyst. The radical mediated catalytic reaction gives excellent yields and the catalyst is reusable up to 4 reaction cycles without losing significant activity.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Understanding coarsening of a post-corrosion microstructure in a molten salt by combining phase-field modeling and in situ tomography

Alloys corroding in molten salt have been observed to form bicontinuous, nanoporous microstructures via dealloying, which subsequently undergo coarsening due to facile transport in high-temperature conditions. In this work, we describe a methodology to elucidate the underlying transport mechanisms during coarsening of a bicontinuous microstructure via quantitative comparisons between phase-field simulations and four-dimensional in situ experiments, in this case X-ray nanotomography of the coarsening of a dealloyed 80 wt% Ni-20 wt% Cr microwire in molten KCl-MgCl 2 at 800°C. We conduct phase-field simulations initialized from experimental data to model coarsening via three different transport mechanisms: surface diffusion, solid bulk diffusion, and liquid bulk diffusion. These simulations reproduce key features of the experiment, such as the densification of the outer layer of the dealloyed wire and the reduction in radius over time. We quantitatively compare different microstructural characteristics between the simulations and experiment and extract temporal scaling factors that optimally match the time scales of the simulations to that of the experiment. This allows us to evaluate morphological similarity between the simulations and experiment and relate the experimental coarsening kinetics to fundamental material properties. We find that surface diffusion is most likely to be the dominant coarsening mechanism, and its kinetics imply a surface diffusivity of D S = 8.9 x 10 -20 m 3 /s, which is within the range of reported values for Ni-vacuum interfaces at 800°C. However, the difference between the experiment and the surface diffusion simulation increases substantially at late times, suggesting that other mechanisms, such as the dissolution of residual Cr, may be at play.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dissolution zone model of the oxide structure in additively manufactured dispersion-strengthened alloys

The structural evolution of oxides in dispersion-strengthened superalloys during laser-powder bed fusion is considered in detail. Alloy chemistry and process parameter effects on oxide structure are assessed through a parameter study on the model alloy Ni-20Cr, doped with varying concentrations of Y 2 O 3 and Al. Small angle neutron scattering measurements of the dispersoid size distribution show the dispersoid size increases with higher laser power, slower scan speed, and increasing Y 2 O 3 and Al content. Complementary electron microscopy measurements reveal reactions between Y 2 O 3 and Al, even in nanoscale dispersoids, and the presence of micron-scale oxide slag inclusions in select specimens. A scaling analysis of mass and momentum transport within the melt pool, presented here, establishes that diffusional structural evolution mechanisms dominate for nanoscale dispersoids, while fluid forces and advection become significant for larger slag inclusions. These findings are developed into a theory of dispersoid structural evolution, integrating quantitative models of diffusional processes – dispersoid dissolution, nucleation, growth, coarsening – with a reduced order model of time-temperature trajectories of fluid parcels within the melt pool. Calculations of the dispersoid size in single-pass melting reveal a zone in the center of the melt track in which the oxide feedstock fully dissolves. Within this zone the final Y 2 O 3 size is independent of feedstock size and determined by nucleation and growth kinetics. If the dissolution zones of adjacent melt tracks overlap sufficiently with each other to dissolve large oxides, formed during printing or present in the powder feedstock, then the dispersoid structure throughout the build volume is homogeneous and matches that from a single pass within the dissolution zone. Gaps between adjacent dissolution zones result in oxide accumulation into larger slag inclusions. Predictions of final dispersoid size and slag formation using this dissolution zone model match the present experimental data and explain process-structure linkages speculated in the open literature.

36 MATERIALS SCIENCE↗
DOE OSTI2026

NiFeCo-based catalysts in high current zero-gap anion exchange membrane water electrolyzers

Understanding degradation mechanisms in pure water anion exchange membrane water electrolyzers is essential for developing durable and precious metal-free hydrogen production systems, yet electronic, chemical, and transport-driven pathways often occur simultaneously at the anode. To separate these effects, we establish a morphology invariant Ni/Fe/Co thin film model catalyst platform using physical vapor deposition and systematically compare composition-dependent behavior under both pure water and 0.1 M KOH feeds. Devices were operated under industrially relevant current density conditions, galvanostatically at 1 A cm −2 for 24 hours; metal dissolution, ionomer oxidation, and resistance growth were quantified using inductively coupled plasma mass spectrometry, X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy. Under pure-water operation, Ni-rich films showed voltage increases that correlated with rising total cell resistance (ΔV ≈ 243 mV, ΔR ≈ 0.17 Ω cm 2 ). Co-rich films maintained near constant voltages with minimal resistance change (ΔV < 10 mV, ΔR ≈ 0.03 Ω cm 2 ) but induced pronounced ionomer oxidation observed by XPS. In 0.1 M KOH, ionomer oxidation is suppressed, and impedance growth is minimized (<0.08 Ω cm 2 ) across all compositions, consistent with reduced transport limitations and improved ionic conduction relative to pure-water feeds. These results demonstrate how a controlled thin film model platform can isolate composition electrolyte relationships and provide mechanistic design principles for stable pure water anion exchange membrane electrolyzers.

Milenia Rojas Mendoza, B. [Stanford Univ., CA (Uni↗
DOE OSTI2023

Retrofitting of carbon-supported bimetallic Ni-based catalysts by phosphorization for hydrogen evolution reaction in acidic media

Commercial bimetallic Ni–Mo and Ni–Re electrocatalysts supported on advanced conductive carbon are high-performing materials for H 2 evolution reaction in alkaline medium, but they cannot be applied in acidic medium due to the rapid dissolution of metals. Here, in this work, we solve this issue by introducing a convenient phosphorization protocol to convert these commercial metallic electrocatalysts into the respective phosphides, rendering them stable under acidic conditions, and thus providing a pathway to electrocatalysts for water reduction in acidic electrolyte. The novel materials demonstrate high performance, as reflected by the measured low overpotentials, shallow Tafel slopes, fast kinetics, as well as excellent stability and durability. This work opens the possibility to expand the applicability of commercial supported metallic catalysts and electrocatalysts through retrofitting via phosphorization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Revealing the Roles of CuF 2 /NiF 2 Incorporation in the Electrochemical Performance of FeF 3 Cathodes in Solid‐State Batteries

Mixed metal fluorides have been considered as a promising candidate to lower the voltage hysteresis of conversion-type iron fluoride cathodes, but their cycling stability is limited due to transition metal dissolution and interphase growth in liquid electrolyte batteries. Here, we study the role of incorporating CuF 2 and NiF 2 in the electrochemical performance of FeF 3 cathode in halide-based solid-state batteries to test whether we can transfer the kinetic benefit of low voltage hysteresis to solid-state batteries while using solid electrolyte to eliminate transition metal dissolution and stabilize the interphase. Synchrotron X-ray absorption spectroscopy results indicated the redox reactions are attributed to Cu 0 /Cu + and Fe 0 /Fe 2+ in 25CuF 2 -75FeF 3 and Ni 0 /Ni 2+ and Fe 0 /Fe 3+ in 10NiF 2 -90FeF 3 . While no apparent improvement in electrode kinetics can be observed, the incorporation of CuF 2 and NiF 2 can largely improve the cycling stability of FeF 3 cathodes. In conclusion, the results demonstrate the advantages of using solid-state concept to improve the cycling stability of conversion-type cathodes.

25 ENERGY STORAGE↗
DOE OSTI2023

Stabilizing the Interphase in Cobalt–Free, Ultrahigh–Nickel Cathodes for Lithium–Ion Batteries

High-nickel layered oxide cathodes, such as LiNi 1-x-y Mn x Co y O 2 (NMC) and LiNi 1-x-y Co x Al y O 2 (NCA), are at the forefront for implementation in high-energy-density lithium-ion batteries. The presence of cobalt in both cathode chemistries, however, largely deters their application due to fiscal and humanitarian issues affiliated with cobalt sourcing. Increasing the Ni content drives down the Co content, but introduces additional structural and electrochemical problems attributed to high-Ni cathodes. Herein a dually modified cobalt-free ultrahigh-nickel cathode 0.02B-LiNi 0.99 Mg 0.01 O 2 (NBM) is presented with 1 mol% Mg and 2 mol% B that exhibits a high initial 1C discharge capacity of 210 mA h g –1 with a 20% capacity retention improvement over 500 cycles when benchmarked against LiNiO 2 (LNO) in pouch full cell configurations with graphite anode. Postmortem analyses reveal the enhanced performance stems from reduced active lithium inventory loss and localized surface reactivity in the NBM cathode. Here, the stabilized cathode-electrolyte interphase subsequently reduces transition-metal dissolution and ensuing chemical crossover to the graphite anode, which prevents further catalyzed parasitic reactions that harmfully passivate the anode surface. Altogether, this study aims to highlight the importance of electrode characterization and analysis from an interphasial viewpoint and to push the ongoing research to stabilize cobalt-free ultrahigh-Ni cathodes for industrial feasibility.

25 ENERGY STORAGE↗