Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nano”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Development of low temperature fuel cell holders for Operando x-ray micro and nano computed tomography to visualize water distribution

Abstract Synchrotron x-ray imaging techniques, like x-ray computed tomography (CT) and radiography have proven instrumental in expanding the communities knowledge of complex transport and reaction kinetics in electrochemical devices such as fuel cells and electrolyzers. This work presents the development of novel x-ray CT imaging techniques for operando visualization of water within low temperature fuel cells at spatial resolutions spanning the micro and nano scales. The design of operando sample holders, for both micro x-ray CT and nano CT experiments is described in depth, and prototypes of these sample holders were evaluated across a set of requirements, the most important of which are x-ray transmissibility, electrical conductivity and mechanical stability. Water segmentation from micro x-ray CT data was enabled by an image subtraction method, where the image without water is subtracted from the one with water. Through iterative experimentations, the operando nano CT cell was developed to optimize mechanical compression, electric conductivity and gas flow. While three-dimensional fuel cell reconstructions were shown possible, there remain challenges to overcome at typical lower energies (8 keV) due to beam damage, whereas it is not as significant for higher energies (>17.5 keV).

Kulkarni, Devashish↗
DOE OSTI2021

Distributed Optimization for Nonrigid Nano-Tomography

Resolution level and reconstruction quality in nano-computed tomography (nano-CT) are in part limited by the stability of microscopes, because the magnitude of mechanical vibrations during scanning becomes comparable to the imaging resolution, and the ability of the samples to resist radiation induced deformations during data acquisition. In such cases, there is no incentive in recovering the sample state at different time steps like in time-resolved reconstruction methods, but instead the goal is to retrieve a single reconstruction at the highest possible spatial resolution and without any imaging artifacts. Here we propose a distributed optimization solver for tomographic imaging of samples at the nanoscale. Our approach solves the tomography problem jointly with projection data alignment, nonrigid sample deformation correction, and regularization. Projection data consistency is regulated by dense optical flow estimated by Farneback's algorithm, leading to sharp sample reconstructions with less artifacts. Synthetic data tests show robustness of the method to Poisson and low-frequency background noise. We accelerated the solver on multi-GPU systems and validated the method on three nano-imaging experimental data sets.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Saccharomyces cerevisiae CellWall Remodeling in the Absence of Knr4 and Kre6 Revealed by Nano-FourierTransform Infrared Spectroscopy

The cell wall integrity (CWI) signaling pathway regulates yeast cell wall biosynthesis, cell division, and responses to external stress. The cell wall, comprised of a dense network of chitin, β-1,3- and β-1,6- glucans, and mannoproteins, is very thin, <100 nm. Alterations in cell wall composition may activate the CWI pathway. Saccharomyces cerevisiae, a model yeast, was used to study the role of individual wall components in altering the structure and biophysical properties of the yeast cell wall. Near-field Fourier transform infrared spectroscopy (nano-FT-IR) was used for the first direct, spectrochemical identification of cell wall composition in a background (wild-type) strain and two deletion mutants from the yeast knock-out collection: kre6Δ and knr4Δ. Killer toxin resistant 6 (Kre6) is an integral membrane protein required for biosynthesis of β-1,6-glucan, while Knr4 is a cell signaling protein involved in the control of cell wall biosynthesis, in particular, biosynthesis and deposition of chitin. Complementary spectral data were obtained with far-field (FF)-FT-IR, in transmission, and with attenuated total reflectance (ATR) spectromicroscopy with 3 –10 μm wavelength-dependent spatial resolution. The FF-FT-IR spectra of cells and spectra of isolated cell wall components showed that components of the cell body dominated transmission spectra and were still evident in ATR spectra. In contrast, the nano-FT-IR at ~25 nm spatial resolution could be used to characterize the yeast wall chemical structure. Our results show that the β-1,6-glucan content is decreased in kre6Δ, while all glucan content is decreased in the knr4Δ cell wall. The latter may be thinner than in wild type, since not only are mannan and chitin detectable by nano-FT-IR, but also lipid membranes and protein, indicative of cell interior.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Nano-Engineered Catalyst Supported on Ceramic Hollow Fibers for the Utilization of CO 2 in Dry Reforming to Produce Syngas

The objective of this project was to develop a novel catalytic reactor containing nano-engineered catalysts for the utilization of CO 2 (captured from coal-fired power plants and other CO 2 emitting sources) in dry methane reforming (DMR) (CO 2 + CH 4 → 2 H 2 + 2 CO) to produce synthesis gas (syngas). The technology aims to reduce CO2 emissions by developing beneficial uses for CO 2 from coal-fired power plants. It also offers an alternative to mitigate CO 2 emissions in areas where geologic storage may not be an optimal solution and/or utilization could significantly offset the costs of carbon capture and sequestration. The nano-engineered Ni-based catalyst was prepared by atomic layer deposition (ALD). The Ni particles were as small as ~2-4 nm. The nano-engineered catalyst showed CH 4 conversion >95%, H 2 /CO ratio in the range of 0.7-1.0, and CH 4 reforming rate as high as 2,500 L/h/gNi at 850 ºC and pressure of 15-25 psia. The Ni-based ALD catalyst also showed good stability in DMR reaction during a 200-h continuous operation at 850 °C. This is due to strong bonding between the nanoparticles and substrates since the Ni nanoparticles were chemically bonded to the substrate during the ALD process. The high thermal stability maintains the high dispersion of Ni nanoparticles, which can inhibit coke formation because their step edges are small enough to limit carbon nucleation and growth. Technoeconomic analysis (TEA) indicates the levelized cost of syngas (LCOS) is $172/ton with our technology, which is lower than the equivalent (molar) cost of hydrogen produced by steam methane reforming (SMR) or autothermal reforming (ATR). The major operating cost is natural gas feed and fuel, and the levelized cost is highly sensitive to the price of natural gas and relatively insensitive to the CAPEX. Revenues from syngas could have a significant impact on the net cost of electricity (COE), depending on the cost of natural gas and the selling price of syngas, estimated at $36 per MWh if the syngas were sold at $195 per ton. Following DOE NETL’s guidance, a lifecycle analysis (LCA) was conducted to compare with SMR. The functional unit for the basis of comparison was defined as 1kg carbon monoxide in the product stream. The global warming potential (GWP) of our process was found to be 40% lower than the state-of-the-art SMR process. The sensitivity analysis confirms the emissions are most sensitive to the natural gas fuel requirements to deliver heat to the process.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Characterization of polysaccharide from Lonicera japonica Thunb leaves and its application in nano-emulsion

The polysaccharides in honeysuckle leaves (PHL) were separated and characterized for the first time. The nano-emulsion stabilized by PHL and whey protein isolate (WPI) were also fabricated based on the ultrasonic method. The results indicated that PHL was mainly composed of glucose (47.40 mol%), galactose (19.21 mol%) and arabinose (20.21 mol%) with the weight-average molecular weight of 137.97 ± 4.31 kDa. The emulsifier concentration, WPI-to-PHL ratio, ultrasound power and ultrasound time had significant influence on the droplet size of PHL-WPI nano-emulsion. The optimal preparation conditions were determined as following: emulsifier concentration, 1.7%; WPI/PHL ratio, 3:1; ultrasonic power, 700 W; ultrasonic time, 7 min. Under the above conditions, the median diameter of the obtained nano-emulsion was 317.70 ± 5.26 nm, close to the predicted value of 320.20 nm. The protective effect of PHL-WPI emulsion on β-carotene against UV irradiation was superior to that of WPI emulsion. Our results can provide reference for the development of honeysuckle leaves.

Li, Yongchao↗
DOE OSTI2021

Synthesis of Core@Shell Cu-Ni@Pt-Cu Nano-Octahedra and Their Improved MOR Activity

Fabrication of 3d metal-based core@shell nanocatalysts with engineered Pt-surfaces provides an effective approach for improving the catalytic performance. The challenges in such preparation include shape control of the 3d metallic cores and thickness control of the Pt-based shells. Herein, we report a colloidal seed-mediated method to prepare octahedral CuNi@Pt-Cu core@shell nanocrystals using CuNi octahedral cores as the template. By precisely controlling the synthesis conditions including the deposition rate and diffusion rate of the shell-formation through tuning the capping ligand, reaction temperature, and heating rate, uniform Pt-based shells can be achieved with a thickness of < 1 nm. Furthermore, the resultant carbon-supported CuNi@Pt-Cu core@shell nano-octahedra showed superior activity in electrochemical methanol oxidation reaction (MOR) compared with the commercial Pt/C catalysts and carbon-supported CuNi@Pt-Cu nano-polyhedron counterparts, demonstrating that both the lattice strain and shape effects arising from the as-prepared CuNi@Pt-Cu octahedral nanocatalysts play a crucial role in MOR performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The Wormholes Within: A Study of 1, 3, 5–Triamino–2, 4, 6–Trinitrobenzene Crystal Morphology by Micro and Nano–Scale X–Ray Computed Tomography and its Effects Upon the Shock Sensitivity of Detonation

We report that we understand heterogeneous-explosive detonation only to the extent that we can first measure the salient chemical and microstructural features. Barring an inordinate amount of trial and error, we can tailor the detonation properties of our HE formulations only to the extent that we understand (at least qualitatively) the same effects. As an insensitive high explosive, 1, 3, 5-triamino-2, 4, 6-trinitrobenzene (TATB) burns more heterogeneously than conventional high explosives, making its detonation properties sensitive to microstructure. The Benziger route can produce various grain morphologies depending on the amount of water used in the amination step. So-called dry-aminated (DA) TATB crystals are riddled with a void structure called wormholes, which are washed out ammonium chloride (NH4Cl) inclusions that form during synthesis. So-called wet-aminated (WA) TATB crystals do not contain NH 4 Cl inclusions but possess a very convoluted external structure. Using both micro and nano-scale CT, we explore three DA-TATB lots that reflect evolutionary processing changes, plus one WA-TATB material. Micro CT imaged crystal collections show the exterior grain structure, revealing its roughness and providing a crude particle size measurement. The DA-TATB lots that test most sensitively in the LANL ECOT corner-turning test are roughest, having the appearance of being “corroded”. Nano-scale CT reveals both internal NH 4 Cl inclusions and void structures. The DA-TATB lots that tested intermediate and high sensitivity in ECOT exhibited similar wormhole structures, which were more extensive than that of the low-sensitivity lot. The least sensitive DA-TATB lot also retained more NH 4 Cl, consistent with reduced connectivity of voids to the surface.

1, 3, 5-triamino-2,4↗
DOE OSTI2025

Heterostructured nano-catalysts with efficient metal-oxide interfaces unlock high-performance direct methanol protonic ceramic fuel cells

Direct methanol protonic ceramic fuel cells (PCFCs) are attractive due to their low cost, convenient storage, and high volumetric energy density, as well as their suitability for transportation. However, the poor coking tolerance of conventional nickel-based anodes leads to their susceptibility to severe carbon deposition and significant deactivation after long-term exposure to hydrocarbons. Herein, we report a nano-catalyst of Ce 0.6 Ni 0.2 Cu 0.2 O 2 with a heterogeneous structure that is spontaneously reduced into a Ce 0.6 Ni 0.2-x Cu 0.2-x O 2-δ (CeNCO) oxide framework interfaced with a nano NiCu alloy (denoted as NC/CeNCO) under operating conditions, as confirmed by analyses of X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. A Ni-BaCe 0.7 Y 0.06 Yb 0.06 Zr 0.06 Hf 0.06 Gd 0.06 O 3-δ anode-supported PCFC employing the NC/CeNCO metal-oxide catalyst achieved a peak power density of 1.11 W cm −2 and operational stability of about 100 h at 700 °C when fueled by 35 % CH 3 OH-15 % H 2 O-50 % N 2 . In conclusion, the enhanced performance and coking resistance are attributed to the efficient interfaces of Ni, Cu, and ceria-based oxide in NC/CeNCO for CH 3 OH reforming, as confirmed by analyses of electrochemical performance and Raman spectroscopy with density functional theory calculations, revealing that these interfaces can enhance CH 3 OH activation and promote efficient OH-mediated carbon removal via COH intermediates.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Self-supported MoO 2 /MoS 2 nano-sheets embedded in a carbon cloth as a binder-free substrate for high-energy lithium–sulfur batteries

As one of the most prospective candidates for next-generation rechargeable batteries, lithium-sulfur (Li-S) batteries currently still encounter great challenges associated with the low conductivity, severe shuttle effects, and sluggish redox kinetics. Herein, a self-supported sulfur host is fabricated by an in-situ growth of MoO 2 /MoS 2 nano-sheets on a carbon cloth (CC). First, carbon cloth serves as a good template for the morphology-controlled synthesis of nanostructured materials, which not only alleviates the agglomeration of MoO2/MoS2, but also enhances the flexibility and mechanical strengthen of the hybrid architecture as a free-standing host. Second, the polysulfide-trapping ability can be greatly enhanced by both physical and chemical adsorption from the MoO 2 /MoS 2 -anchored carbon cloth. Moreover, the partially sulfurized MoO 2 /MoS 2 nano-sheets integrate the benefits of conductive MoO 2 and sulfiphilic MoS 2 , thus facilitating fast charge transfer and redox kinetics of polysulfide conversion. As a result, these attributes enable the host to hold a high sulfur loading (up to 7.6 mg cm -2 ), which exceeds most of the reported carbon cloth-related cathode work in the literature. Furthermore, the Li-S cells can achieve a high peak capacity of 1350 mA h g -1 , excellent rate capability (C/20 - 2C rate), impressive areal capacity (up to 6.3 mA h cm -2 ), and a high capacity retention of 85% after 100 cycles.

25 ENERGY STORAGE↗
DOE OSTI2025

Multi-phase characterization of pitch-carbon coated nano-silicon anodes for lithium-ion batteries

Silicon (Si) is a leading next-generation Li-ion battery anode candidate that meets rigorous performance demands for portable power including enhanced power and energy density with robust cycling performance. However, a series of complex and interrelated reactions lead to reduced calendar life in Si-containing systems and therefore challenge practical adoption. In the present work, we probe the mechanisms underlying observed performance improvements by adding a pitch-carbon coating onto nano-Si material. We pair solid-phase (X-ray photoemission spectroscopy, Fourier-transform infrared), semi-volatile phase (solid-phase microextraction-gas chromatography-mass spectrometry), and gas-phase (gas chromatography-flame-ionization detector) characterization signals to comprehensively evaluate the impact of pitch-carbon coating on the evolution of the Si solid-electrolyte interphase (SEI) and the associated impacts on electrode/electrolyte reactivity. The pitch-carbon is found to serve as a physicochemical barrier, reducing the electro-active surface area for Si/electrolyte reactivity and preventing Si oxidation. Further, the pitch-carbon coating promotes the evolution of a more-favorable SEI by subsuming substantial functionality typically associated with the fluoroethylene carbonate (FEC) electrolyte additive - such as alkoxide scavenging and suppression of transesterification pathways - and by shifting the competitive electrolyte degradation pathways' favorability. The multi-phase characterization approach enables holistic end-products evaluation from complex (electro)chemical interfacial reactions, which informs a robust interpretation of the carbon coating's role in electrochemical performance improvements. The present mechanistic evaluation aids the rational design for improved nano-Si materials.

25 ENERGY STORAGE↗
DOE OSTI2020

Estimating diffusion coefficients of shale oil, gas, and condensate with nano-confinement effect

Molecular diffusion plays an important role in oil and gas migration in tight shale formations. However, there are insufficient reference data in the literature to specify the diffusion coefficients within porous media. This study aims at calculating diffusion coefficients of shale gas, shale condensate, and shale oil at reservoir conditions with CO 2 injection for EOR/EGR. The large nano-confinement effects including large gas-oil capillary pressure and critical property shifts could alter the phase behaviors. This paper estimates the diffusivities of shale fluids in nanometer-scale shale rock from two perspectives: 1) examining the shift of diffusivity caused by nanopore confinement effects from phase change (phase composition and fluid property) perspective, and 2) calculating the effective diffusion coefficient in porous media by incorporating rock intrinsic properties (porosity and tortuosity factor). The tortuosity is obtained by using tortuosity-porosity relations as well as the measured tortuosity of shale from 3D imaging techniques. The results indicated that nano-confinement effects could affect the diffusion coefficient through altering the phase properties, such as phase compositions and densities. Compared to bulk phase diffusivity, the effective diffusion coefficient in porous shale rock is reduced by 10 2 to 10 4 times as porosity decreases from 0.1 to 0.03.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

X-ray-Based Techniques to Study the Nano–Bio Interface

X-ray-based analytics are routinely applied in many fields, including physics, chemistry, materials science, and engineering. The full potential of such techniques in the life sciences and medicine, however, has not yet been fully exploited. We highlight current and upcoming advances in this direction. We describe different X-ray-based methodologies (including those performed at synchrotron light sources and X-ray free-electron lasers) and their potentials for application to investigate the nano–bio interface. The discussion is predominantly guided by asking how such methods could better help to understand and to improve nanoparticle-based drug delivery, though the concepts also apply to nano–bio interactions in general. We discuss current limitations and how they might be overcome, particularly for future use in vivo.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Deep-learning-based image registration for nano-resolution tomographic reconstruction

Nano-resolution full-field transmission X-ray microscopy has been successfully applied to a wide range of research fields thanks to its capability of non-destructively reconstructing the 3D structure with high resolution. Due to constraints in the practical implementations, the nano-tomography data is often associated with a random image jitter, resulting from imperfections in the hardware setup. Without a proper image registration process prior to the reconstruction, the quality of the result will be compromised. Here a deep-learning-based image jitter correction method is presented, which registers the projective images with high efficiency and accuracy, facilitating a high-quality tomographic reconstruction. This development is demonstrated and validated using synthetic and experimental datasets. We report the method is effective and readily applicable to a broad range of applications. Together with this paper, the source code is published and adoptions and improvements from our colleagues in this field are welcomed.

deep learning↗
DOE OSTI2024

Electrolyzer Integrated Modular Nano-Array Monolithic Catalytic Reactors

The project objective is to design and develop a new class of electrolyzer-integrated, modular, nanostructure array (nano-array) monolithic catalytic reactors for high-flux, robust and selective methanol synthesis. The modular reactor features metal oxide nano-array grown on an additively-manufactured channeled honeycomb monolith made of ceramic or metals; this low-pressure carbon dioxide hydrogenation reactor is fueled with hydrogen from a low-temperature water electrolyzer having reduced platinum group metal (PGM) content. Through these nanostructured monolithic reactors, methanol synthesis is enabled with cost-effective hydrogenation reactions under low-temperature (<200°C) and low-pressure (<10 atm) conditions, thus significantly reducing the energy demand of the entire process.

08 HYDROGEN↗
DOE OSTI2022

Synthesis of Nano-Oxide Precipitates by Implantation of Ti, Y and O Ions in Fe-10%Cr: Towards an Understanding of Precipitation in Oxide Dispersion-Strengthened (ODS) Steels

The properties of oxide dispersion-strengthened steels are highly dependent on the nature and size distribution of their constituting nano-oxide precipitates. A fine control of the processes of synthesis would enable the optimization of pertinent properties for use in various energy systems. This control, however, requires knowledge of the precise mechanisms of nucleation and growth of the nanoprecipitates, which are still a matter of debate. In the present study, nano-oxide precipitates were produced via the implantation of Y, Ti, and O ions in two different sequential orders in an Fe-10%Cr matrix that was subsequently thermally annealed. The results show that the oxides that precipitate are not necessarily favoured thermodynamically, but rather result from complex kinetics aspects related to the interaction between the implanted elements and induced defects. When Y is implanted first, the formation of nanoprecipitates with characteristics similar to those in conventionally produced ODS steels, especially with a core/shell structure, is evidenced. In contrast, when implantation starts with Ti, the precipitation of yttria during subsequent high-temperature annealing is totally suppressed, and corundum Cr 2 O 3 precipitates instead. Moreover, the systematic involvement of {110} matrix planes in orientation relationships with the precipitates, independently of the precipitate nature, suggests matrix restriction effects on the early stages of precipitation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ionic Liquid-Mediated Scanning Probe Electro-Oxidative Lithography as a Novel Tool for Engineering Functional Oxide Micro- and Nano-Architectures

Functional oxides have extensively been investigated as a promising class of materials in a broad range of innovative applications. Harnessing the novel properties of functional oxides in micro- to nano-scale applications hinges on establishing advanced fabrication and manufacturing techniques able to synthesize these materials in an accurate and reliable manner. Oxidative scanning probe lithography (o-SPL), an atomic force microscopy (AFM) technique based on anodic oxidation at the water meniscus formed at the tip/substrate contact, not only combines the advantages of both “top-down” and “bottom-up” fabrication approaches, but also offers the possibility of fabricating oxide nanomaterials with high patterning accuracy. While the use of self-assembled monolayers (SAMs) broadened the application of o-SPL, significant challenges have emerged owing to the relatively limited number of SAM/solid surface combinations that can be employed for o-SPL, which constrains the ability to control the chemistry and structure of oxides formed by o-SPL. Here, in this work, a new o-SPL technique that utilizes room-temperature ionic liquids (RTILs) as the functionalizing material to mediate the electrochemistry at AFM tip/substrate contacts is reported. The results show that the new IL-mediated o-SPL (IL-o-SPL) approach allows sub-100 nm oxide features to be patterned on a model solid surface, namely steel, with an initiation voltage as low as -2 V. Moreover, this approach enables high tunability of both the chemical state and morphology of the patterned iron oxide structures. Owing to the high chemical compatibility of ILs, which derives from the possibility of synthesizing ILs able to adsorb on a wide variety of solid surfaces, IL-o-SPL can be extended to other material surfaces and provide the opportunity to accurately tailor the chemistry, morphology, and electronic properties within nanoscale domains, thus opening new pathways to the development of novel micro- and nano-architectures for advanced integrated devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unique Role of GeO 2 as a Noninvasive Promoter of Nano‐Sized Zeolite Crystals

Abstract The synthesis of zeolites with nano‐sized dimensions is often limited to a narrow design space that conventionally relies upon the design of organics to direct hierarchical materials. Here, it is demonstrated that the addition of an inorganic modifier, germanium oxide (GeO 2 ), to a zeolite growth mixture directs the formation of crystals with ultrasmall dimensions. This effect is observed for zeolites ZSM‐11 and ZSM‐5 over a range of synthesis conditions wherein the role of GeO 2 in zeolite crystallization deviates from its typical function as a heteroatom. Notably, the final products contain trace amounts of Ge, which indicates the inorganic modifier does not compete for sites in the zeolite framework based on its formation of a discrete phase that enables GeO 2 recovery. Catalytic tests using the methanol‐to‐hydrocarbons reaction reveal significant enhancement in the performance of zeolite catalysts prepared with GeO 2 compared to reported examples of nano‐sized zeolites. These findings highlight a potentially generalizable and commercially viable synthesis method to reduce mass‐transport limitations in zeolites for diverse applications.

Chemistry↗
DOE OSTI2024

Organic Nano-Junctions: Linking Nanomorphology and Charge Transport in Organic Semiconductor Nanoparticles for Organic Photovoltaic Devices

In this study, innovative nanoscale devices are developed to investigate the charge transport in organic semiconductor nanoparticles. Using different steps of lithography techniques and dielectrophoresis, planar organic nano-junctions are fabricated from which hole mobilities are extracted in a space charge-limited current regime. Subsequently, these devices are used to investigate the impact of the composition and morphology of organic semiconductor nanoparticles on the charge mobilities. Pure donor nanoparticles and composite donor:acceptor nanoparticles with different donor compositions in their shell are inserted in the nanogap electrode to form the nano-junctions. The results highlight that the hole mobilities in the composite nanoparticles decrease by two-fold compared to pure donor nanoparticles. However, no significant change between the two kinds of composite nanoparticle morphologies is observed, indicating that conduction pathways for the holes are as efficient for donor proportion in the shell from 40% to 60%. Organic photovoltaic (OPV) devices are fabricated from water-based colloidal inks containing the two composite nanoparticles (P3HT:eh-IDTBR and P3HT:o-IDTBR) and no significant change in the performances is observed in accordance with the mobility results. Through this study, the performance of OPV devices have been successfully correlated to the transport properties of nanoparticles having different morphology via innovative nanoscale devices.

42 ENGINEERING↗