SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This presentation gives an overview of the technology, methods and processes developed during the TC3 Technical Challenge of the System-Wide Safety (SWS) project. The presentation goes over the motivation for doing this research, gives an overview of the tool, methods and process developed under this program, and describes case studies and impact in industry.
The status of an investigation of four numerical techniques for the time-dependent compressible Navier-Stokes equations is presented. Results for free shear layer calculations in the Reynolds number range from 1000 to 81000 indicate that a sequential alternating-direction implicit (ADI) finite-difference procedure requires longer computing times to reach steady state than a low-storage hopscotch finite-difference procedure. A finite-element method with cubic approximating functions was found to require excessive computer storage and computation times. A fourth method, an alternating-direction cubic spline technique which is still being tested, is also described.
An empirical approach to determine the redding in WN stars is presented, in which the measured strengths of the emission lines of He II at 1640 and 4686 A are used to estimate the extinction. The He II emission lines at these wavelengths are compared for a number of WN stars in the Galaxy and the LMC. It is shown that the equivalent width ratios are single valued and are independent of the spectral subtypes. The reddening for stars in the Galaxy is derived using a Galactic extinction law and observed line flux ratios, showing good agreement with previous determinations of reddening. The possible application of the method to study the absorption properties of the interstellar medium in more distant galaxies is discussed.
Although pyrotechnic devices have been singularly responsible for the success of many of the critical mechanical functions in aerospace programs for over 30 years, ground and in-flight failures continue to occur. Subsequent investigations reveal that little or no quantitative information is available on measuring the effects on performance of system variables or on determining functional margins. Pyrotechnics are considered to be readily available and, therefore, can be managed by any subsystem in which they are applied, such as structure, propulsion, electric power, or life support. The primary purpose of this manual is to alter the concept that the use of pyrotechnics is an art and refute 'justifications' that applications do not need to be understood by providing information on pyrotechnic design, development, and qualification on an engineering basis. Included are approaches to demonstrate functional reliability with less than 10 units, how to manage pyrotechnic-unique requirements, and methods to assure that the system is properly assembled and will perform the required tasks.
Software-Only-Simulations have been an emerging but quickly developing field of study throughout NASA. The NASA Independent Verification Validation (IVV) Independent Test Capability (ITC) team has been rapidly building a collection of simulators for a wide range of NASA missions. ITC specializes in full end-to-end simulations that enable developers, VV personnel, and operators to test-as-you-fly. In four years, the team has delivered a wide variety of spacecraft simulations that have ranged from low complexity science missions such as the Global Precipitation Management (GPM) satellite and the Deep Space Climate Observatory (DSCOVR), to the extremely complex missions such as the James Webb Space Telescope (JWST) and Space Launch System (SLS).This paper describes the evolution of ITCs technologies and processes that have been utilized to design, implement, and deploy end-to-end simulation environments for various NASA missions. A comparison of mission simulators are discussed with focus on technology and lessons learned in complexity, hardware modeling, and continuous integration. The paper also describes the methods for executing the missions unmodified flight software binaries (not cross-compiled) for verification and validation activities.
The Earth's atmosphere is impacted daily by both meteoroids and artificial objects. Calibrated observations of the emitted light at sufficiently high sampling rates can enable or improve the estimation of impactor attributes such as size, cohesion, trajectory, and composition, but are difficult to obtain owing to the unpredictability, brevity, and high dynamic (brightness) range of impacts. Ground-based camera systems have successfully monitored small regions of the atmosphere at video frame rates and with limited radiometric capabilities, but most impacts occur over the 70% of the Earth's surface covered by water and are therefore missed by these networks. The Geostationary Lightning Mapper (GLM) instruments aboard Geostationary Operational Environmental Satellites 16 and 17 provide near-hemispherical coverage at 500 frames per second. These data have been shown to contain the signatures of many independently confirmed impacts, often from both viewing angles simultaneously, and constitute an observational resource that is currently unparalleled in the public domain. NASA's Asteroid Threat Assessment Project has implemented an automated impact detection pipeline that processes data from GLM daily. Given a detected impact, the GLM data contain a wealth of information for use in quantitative follow-up analyses. However, impact events differ from lightning in ways that violate key assumptions built into GLM's design. The result is that GLM's onboard processing introduces errors into pixel observations of impact events and the calibrated energies near the periphery of the detector may be substantially overestimated. We present methods for mitigating these and other issues to produce a data product more suitable for impact analyses than the existing GLM lightning product.
A simple test method for the measurement of delamination resistance is assessed through its application to 11-ply graphite-epoxy laminates whose matrices employ the F185 and 205 resins. The F185 resin has the same base epoxy as the 205, to which liquid and solid elastomers have been added. The critical value of the mixed mode energy release rate, calculated from a closed form equation employing nominal strain measurements from the onset of edge delamination, show that addition of the elastomers to the base epoxy increases interlaminar fracture toughness. Comparison of these results with those of width-tapered double cantilever beam (WTDCB) test data for the two materials shows a similar strain energy release rate, establishing the accuracy of the novel method. Both tests are found to be needed, however, for the quantitative characterization of interlaminar fracture toughness.
The ChemCam instrument selected for the Curiosity rover is capable of remote laser-induced breakdown spectroscopy (LIBS).[1] We used a remote LIBS instrument similar to ChemCam to analyze 197 geologic slab samples and 32 pressed-powder geostandards. The slab samples are well-characterized and have been used to validate the calibration of previous instruments on Mars missions, including CRISM [2], OMEGA [3], the MER Pancam [4], Mini-TES [5], and Moessbauer [6] instruments and the Phoenix SSI [7]. The resulting dataset was used to compare multivariate methods for quantitative LIBS and to determine the effect of grain size on calculations. Three multivariate methods - partial least squares (PLS), multilayer perceptron artificial neural networks (MLP ANNs) and cascade correlation (CC) ANNs - were used to generate models and extract the quantitative composition of unknown samples. PLS can be used to predict one element (PLS1) or multiple elements (PLS2) at a time, as can the neural network methods. Although MLP and CC ANNs were successful in some cases, PLS generally produced the most accurate and precise results.
The use of composite materials for a variety of practical structural applications is presented and the need for an accelerated characterization procedure is assessed. A new experimental and analytical method is presented which allows the prediction of long term properties from short term tests. Some preliminary experimental results are presented.
A survey of integral methods in laminar-boundary-layer analysis is first given. A simple and sufficiently accurate method for practical purposes of calculating the properties (including stability) of the laminar compressible boundary layer in an axial pressure gradient with heat transfer at the wall is presented. For flow over a flat plate, the method is applicable for an arbitrarily prescribed distribution of temperature along the surface and for any given constant Prandtl number close to unity. For flow in a pressure gradient, the method is based on a Prandtl number of unity and a uniform wall temperature. A simple and accurate method of determining the separation point in a compressible flow with an adverse pressure gradient over a surface at a given uniform wall temperature is developed. The analysis is based on an extension of the Karman-Pohlhausen method to the momentum and the thermal energy equations in conjunction with fourth- and especially higher degree velocity and stagnation-enthalpy profiles.
Scientific visualizations of two-dimensional compressible flow of a gas with discontinuities are presented. The numerical analogue to experimental techniques such as schlieren imaging, shadowgraphs, and interferograms are discussed. Edge detection techniques are utilized to identify the discontinuities. In particular, the zero crossing of the Laplacian of a field (usually density) is recommended for extracting the discontinuities. An algorithm to extract and quantify the discontinuities is presented. To illustrate the methods developed in the report, the example chosen is that of an unsteady interaction of a shock wave with a contact discontinuity.
This paper describes experimental investigations of devices designed for the nonintrusive detection of terminal shock location in mixed-compression inlets at high supersonic flight speeds. Systems based on sensing wall pressures by an array of wall-mounted transducers were selected for detailed study. Pressure signals were processed by three different methods: (1) interpretation of instantaneous pressure distributions, (2) detection of the turbulent intensity amplification occurring at the shock, and (3) determination of the upstream limit to which a search-tone, introduced at the downstream end of the channel, can propagate. The first two of these methods were tested in real time. The third method appeared feasible for weak shocks only; at high shock strengths, propagation upstream of the source could not be detected.
Following the failure of a previously qualified pyrotechnically actuated pin puller design, an investigation led to a redesign and requalification. The emphasis of the second qualification was placed on determining the functional margin of the pin puller by comparing the energy deliverable by the pyrotechnic cartridge to the energy required to accomplish the function. Also determined were the effects of functional variables. This paper describes the failure investigation, the test methods employed and the results of the evaluation, and provides a recommended approach to assure the successful functioning of pyrotechnic devices.
Following the failure of a previously qualified pyrotechnically actuated pin puller design, an investigation led to a redesign and requalification. The emphasis of the second qualification was placed on determining the functional margin of the pin puller by comparing the energy deliverable by the pyrotechnic cartridge to the energy required to accomplish the function. Also determined were the effects of functional variables. This paper describes the failure investigation, the test methods employed and the results of the evaluation, and provides a recommended approach to assure the successful functioning of pyrotechnic devices.
The depth to which sunlight will penetrate in turbid waters was investigated. The tests were conducted in water with a single scattering albedo range, and over a range of solar elevation angles. Two different techniques were used to determine the depth of light penetration. It showed little change in the depth of sunlight penetration with changing solar elevation angle. A comparison of the penetration depths indicates that the best agreement between the two methods was achieved when the quasisingle scattering relationship was not corrected for solar angle. It is concluded that sunlight penetration is dependent on inherent water properties only.
An algorithm for automatic analysis of stereoscopic images is applied to stereo pairs of severe local storms and hurricanes observed by two GOES satellites. The automatically derived height fields and manual analyses are compared. It is found that the automatic analysis produces a more detailed structure in less time than manual analysis, although the two methods have similar quality. In areas where the features are very small, however, it is suggested that manual analysis is superior.
This paper discusses the history of SE&I management of the overall program architecture, organizational structure and the relationship of SE&I to other program organizational elements. A brief discussion of the method of executing the SE&I process, a summary of some of the major lessons learned, and identification of things that have proven successful are included.
Marine Spatial Planning (MSP) provides a process that uses spatial data and models to evaluate environmental, social, economic, cultural, and management trade-offs when siting (i.e., strategically locating) ocean industries. Aquaculture is the fastest-growing food sector in the world. The United States (U.S.) has substantial opportunity for offshore aquaculture development given the size of its exclusive economic zone, habitat diversity, and variety of candidate species for cultivation. However, promising aquaculture areas overlap many protected species habitats. Aquaculture siting surveys, construction, operations, and decommissioning can alter protected species habitat and behavior. Additionally, aquaculture-associated vessel activity, underwater noise, and physical interactions between protected species and farms can increase the risk of injury and mortality. In 2020, the U.S. Gulf of Mexico was identified as one of the first regions to be evaluated for offshore aquaculture opportunities as directed by a Presidential Executive Order. We developed a transparent and repeatable method to identify aquaculture opportunity areas (AOAs) with the least conflict with protected species. First, we developed a generalized scoring approach for protected species that captures their vulnerability to adverse effects from anthropogenic activities using conservation status and demographic information. Next, we applied this approach to data layers for eight species listed under the Endangered Species Act, including five species of sea turtles, Rice’s whale, smalltooth sawfish, and giant manta ray. Next, we evaluated four methods for mathematically combining scores (i.e., Arithmetic mean, Geometric mean, Product, Lowest Scoring layer) to generate a combined protected species data layer. The Product approach provided the most logical ordering of, and the greatest contrast in, site suitability scores. Finally, we integrated the combined protected species data layer into a multi-criteria decision-making modeling framework for MSP. This process identified AOAs with reduced potential for protected species conflict. These modeling methods are transferable to other regions, to other sensitive or protected species, and for spatial planning for other ocean-uses.