SEARCH · Engineering Papers

Results for “Molybdenum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1971

Molybdenum-UO2 cerment irradiation at 1145 K

Two molybdenum-UO2 cermet fuel pins were fission heated in a helium-cooled loop at a temperature of 1145 K and to a total burnup of 5.3 % of the U-235. After irradiation the fuel pins were measured to check dimensional stability, punctured at the plenums to determine fission gas release, and examined metallographically to determine the effect of irradiation. Burnup was determined in several sections of the fuel pin. The results of the postirradiation examination indicated: (1) There was no visible change in the fuel pins on irradiation under the above conditions. (2) The maximum swelling of the fuel pins was less than 1%. (3) There was no migration of UO2 and no visible interaction between the molybdenum and the UO2. (4) Approximately 12% of the fission gas formed was released from the cermet cone into the gas plenum.

Mcdonald, G.↗

NASA NTRS1972

A simple spectrophotometric method for determination of zirconium or hafnium in selected molybdenum-base alloys

A simple analytical procedure is described for accurately and precisely determining the zirconium or hafnium content of molybdenum-base alloys. The procedure is based on the reaction of the reagent Arsenazo III with zirconium or hafnium in strong hydrochloric acid solution. The colored complexes of zirconium or hafnium are formed in the presence of molybdenum. Titanium or rhenium in the alloy have no adverse effect on the zirconium or hafnium complex at the following levels in the selected aliquot: Mo, 10 mg; Re, 10 mg; Ti, 1 mg. The spectrophotometric measurement of the zirconium or hafnium complex is accomplished without prior separation with a relative standard deviation of 1.3 to 2.7 percent.

Dupraw, W. A.↗

NASA NTRS1974

Evaluation of chromium oxide and molybdenum disulfide coatings in self-acting stops of an air-lubricated Rayleigh step thrust bearing

Two coatings for a Rayleigh step thrust bearing were tested when coasting down and stopping under self-acting operation in air. The thrust bearing had an outside diameter of 8.9 cm (3.5 in.), an inside diameter of 5.4 cm (2.1 in.), and nine sectors. The load was 73 N (16.4 lbf). The load pressure was 19.1 kN/per square meter (2.77 lbf/per square inch) on the total thrust bearing area. The chromium oxide coating was good to 150 stops without bearing deterioration, and the molybdenum disulfide coating was good for only four stops before bearing deterioration. The molybdenum disulfide coated bearing failed after nine stops.

Nemeth, Z. N.↗

NASA NTRS1974

Determination of copper, scandium, molybdenum, tin, lead, and iron group elements in lunar surface materials

Distribution regularities of copper, scandium, molybdenum, tin, lead, and iron group elements were investigated in basaltoid rocks of lunar and terrestrial origin. Samples of various regolith zones taken in the area of the Sea of Fertility were analyzed, along with samples of basic and ultrabasic rocks of the East African Rift for their content of the trace admixtures listed. Data obtained on the abundance of copper, scandium, molybdenum, tin, lead, cobalt, nickel, chromium, and vanadium in Luna 16 lunar surface material were compared with the abundance of these elements in samples of lunar rocks returned by Apollo 11, Apollo 12, and Apollo 14, with the exception of scandium; its content in the latter samples was considerably higher.

Pavlenko, L. I.↗

NASA NTRS1975

A review of chromium, molybdenum, and tungsten alloys

The mechanical properties of chromium, molybdenum, and tungsten alloys are reviewed with particular emphasis on high-temperature strength and low-temperature ductility. Precipitate strengthening is highly effective at 0.4 to 0.8 times the melting temperature in these metals, with HfC being most effective in tungsten and molybdenum, and Ta(B,C) most effective in chromium. Low-temperature ductility can be improved by alloying to promote rhenium ductilizing or solution softening. The low-temperature mechanical properties of these alloys appear related to electronic interactions rather than to the usual metallurgical considerations.

Klopp, W. D.↗

NASA NTRS1976

Effect of nature of oxygen interactions on friction of titanium, aluminum, and molybdenum

Friction studies were conducted with a gold pin contacting titanium, aluminum, and molybdenum surfaces after exposure to oxygen with various methods. Oxygen was adsorbed on the surface, it reacted with the surface, and the surface was ion bombarded with oxygen. The presence of oxygen was monitored with Auger spectroscopy. Titanium friction varied with the mode of the metal-oxygen interaction. It was highest with the adsorbed oxygen and least with ion bombardment using oxygen. Aluminum exhibited lower friction values for the reacted and the ion bombarded surfaces than for the surface having the adsorbed layer. With molybdenum the friction coefficients were generally the same despite the nature of the surface treatment with oxygen.

Buckley, D. H.↗

NASA NTRS1977

Critical currents in sputtered copper molybdenum sulphide

Critical currents in a sputtered Chevrel-phase copper molybdenum sulfide have been measured at 4.2 K as a function of applied magnetic field. Self-field critical-current values up to 10 to the 9th A/sq m were found, decreasing to 10 to the 8th A/sq m at 3 T. Graphs of pinning forces versus field were found to be independent of field direction, and the pinning mechanism is sample independent. Critical-current densities for sputtered lead molybdenum sulphide are estimated to be about 10 to the 8th A/sq m at 26 T based on a scaling law for pinning.

Alterovitz, S. A.↗

NASA NTRS1978

A study of the mechanisms of hydrogen embrittlement in molybdenum

The mechanical properties of polycrystalline molybdenum samples in both the 'as annealed' and hydrogenized conditions were studied. The results indicate that hydrogen does not alter the yield stress of samples significantly although it reduces both the ultimate tensile strength and the ductility considerably. Fractographic study of samples shows a tendency to intercrystalline cracking of the hydrogenised molybdenum at low temperatures. In the light of the results, a mechanism involving grain boundary weakening is suggested.

Taheri, M.↗

NASA NTRS1978

Upper critical field of copper molybdenum sulfide

The upper critical field of sintered and sputtered copper molybdenum sulfide Cu(x)Mo6S8 was measured and found to exceed the Werthamer, Helfand, and Hohenberg (1966) value for a type II superconductor characterized by dirty limit, weak isotropic electron phonon coupling, and no paramagnetic limiting. It is suggested that the enhancement results from anisotropy or clean limit or both. Other ternary molybdenum sulfides appear to show similar anomalies.

Alterovitz, S. A.↗

NASA NTRS1978

Thermocouples of molybdenum and iridium alloys for more stable vacuum-high temperature performance

Thermocouples providing stability and performance reliability in systems involving high temperatures and vacuums by employing a bimetallic thermocouple sensor are described. Each metal of the sensor is selected from a group of metals comprising molybdenum and iridium and alloys containing only those two metals. The molybdenum, iridium thermocouple sensor alloys provide bare metal thermocouple sensors having advantageous vapor pressure compatibility and performance characteristics. The compatibility and physical characteristics of the thermocouple sensor alloys result in improved emf, temperature properties and thermocouple hot junction performance.

Morris, J. F.↗

NASA NTRS1978

Normal state properties of the ternary molybdenum sulfides

By making a large number of normal state and superconducting properties measurements, all on the same ternary molybdenum sulfide samples, we obtain values for Fermi surface and superconducting parameters. From these we conclude that sputtered ternary molybdenum sulfides are not completely in the dirty superconductor limit, and that they are d-band metals with a high electron carrier density.

Woollam, J. A.↗

NASA NTRS1978

Reactively evaporated films of copper molybdenum sulfide

Films of superconducting Chevrel-phase copper molybdenum sulfide CuxMo6S8 were deposited on sapphire substrates by reactive evaporation using H2S as the reacting gas. Two superconducting temperatures (10.0 K and 5.0 K) of the films were found, corresponding to two different phases with different copper concentrations. All films were superconducting above 4.2 K and contained Chevrel-phase compound as well as free molybdenum. The critical current was measured as a function of applied field. One sample was found to deviate from the scaling law found for co-evaporated or sputtered samples, which possibly indicates a different pinning mechanism or inhomogeneity of the sample.

Chi, K. C.↗

NASA NTRS1980

The influence of isothermal annealing on the molybdenum fibers of a directed solid gamma/gamma prime - alpha alloy

The mechanical characteristics of the directed solid eutectic Ni-Al-Mo (gamma/gamma prime)-alpha alloy at high temperatures make it useful in the blades of gas turbines. Structural changes are observed for the alloy under isothermal annealing, particularly the formation of molybdenum plates at the grain boundary and an increase of the gamma phase in relation to the gamma prime phase. Molybdenum lamellas appear at the grain boundary above 1100 C which can have a negative influence on the mechanical properties. The change in the structure near the grain boundary with the increase in temperature is illustrated through a sequence of pictures.

Whittenberger, J. D.↗

NASA NTRS1984

Oxidation characteristics of molybdenum-zirconium oxide cermets

The oxidation of molybdenum is affected by the factors of temperature, the oxygen pressure in the oxidizing atmosphere, and the time of exposure. Studies of the oxidation characteristics of Mo show that the oxidation rate increases strongly when the temperature exceeds 600 C. Investigations of the behavior of cermets with various percentages of zirconium oxide are discussed, taking into account oxidation conditions at temperatures under and above the melting point of molybdenum trioxide.

Heitzinger, B.↗

NASA NTRS1984

Electrotransport and diffusivity of molybdenum, rhenium, tungsten, and zirconium in beta-thorium

The electric mobilities, diffusivities, and effective valences were determined for molybdenum, rhenium, tungsten, and zirconium in beta-thorium. All four solutes migrated in the same direction as the electron flow. Rhenium and molybdenum were found to be very mobile, with tungsten somewhat slower. Zirconium was found to move at a rate near that of the self-diffusion of beta-thorium, viz., about 10 to the -11th sq m/s at 1500 C. The electromigration velocities showed a similar trend. A comparison was made between experimental data obtained by scanning laser mass spectrometry and theoretical transport equations for two purification experiments. Good agreement was obtained with both the concentration profile predicted by DeGroot and the purification ratio predicted by Verhoeven.

Schmidt, F. A.↗

NASA NTRS1985

Molybdenum-silicon multilayer mirrors for the extreme ultraviolet

Multilayer structures of molybdenum and silicon have been synthesized by sputter deposition onto flat silicon single-crystal silicon substrates and spherically ground (0.5and 22.0-m radii) fused silica substrates; and the reflectivities for 170.4-A (72.8-eV), 160.1-A (77.4-eV), and 228-A (54.4-eV) light measured at near normal incidence. Observed peak values ranged from 26.2 to 78 percent, the highest reflectivities occurring closest to normal incidence. Energy resolutions were about 10 in all cases. Model calculations were performed using optical constants and experimentally determined multilayer structural parameters. In all cases the measured reflectivities were equal to or larger (by up to a factor of 2) than the calculated values, a result attributed to uncertainty in the optical constants used in the calculations. Experimental and calculated angular-peak positions and energy resolutions were in good agreement. The high reflectivities of these molybdenum-silicon structures will make possible application of traditional optics approaches in the EUV and support new developments including free-electron lasers.

Barbee, T. W., Jr.↗

NASA NTRS1986

Voltammetric studies of porous molybdenum electrodes for the alkali metal thermoelectric converter

Voltammetry of partially oxidized porous molybdenum alkali metal thermoelectric converter (AMTEC) electrodes from about 600 to 1000 K revealed a series of redox processes within the AMTEC operational voltage range which can be used to establish the electronic and ionic conductivities of these electrodes. Improved estimates of the free energies of formation of Na2Mo3O6, NaMoO2, and Na3MoO4 are obtained. Evidence is provided for the slow corrosive attack by Na2MoO4 on molybdenum. The ionic conductivity of Na2MoO4 is found to be sufficiently large at temperatures of greater than 700 K to explain the observed electrochemical phenomena in addition to the enhanced sodium transport in AMTEC electrodes below the freezing point of Na2MoO4.

Williams, R. M.↗

NASA NTRS1990

Secondary electron emission characteristics of molybdenum-masked, ion-textured OFHC copper

A method for producing a uniform, highly textured surface on oxygen-free, high conductivity (OFHC) copper by ion bombardment using sputtered molybdenum as a texture-inducing masking film was developed and used to provide samples for study. The purpose was to develop a basically OFHC copper surface having very low secondary electron emission characteristics. Surfaces having low secondary electron emission are a requirement for the electrodes of very high efficiency multistage depressed collectors (MDC's). Such MDC's are used in microwave amplifier traveling wave tubes for space communications and other applications. OFHC copper is the material most commonly used for MDC electrodes because it has high thermal conductivity, it is easy to machine, and its fabrication and brazing procedures are well established. However, its untreated surface displays relatively very high levels of secondary electron emissions. Textured OFHC copper samples were tested for true secondary electron emission and relative reflected primary electron yield at primary electron beam energy levels from 200 to 2000 eV and at direct (0 deg) to oblique (60 deg) beam impingement angles. The test results for three of the samples, each of which was processed in a slightly different way, are compared with each other and with test results for a machined OFHC copper sample. Although the textured samples are not represented here as having been processed optimally, their measured secondary electron emission characteristics are significantly lower than those of the untreated OFHC copper sample over the range of conditions studied. Importantly, the relative reflected primary electron yield of one of the textured samples is conspicuously lower than that of the others. Clearly, with further development, the molybdenum-masked ion-textured OFHC copper surface will be a promising material for high-efficiency MDC electrodes.

Curren, Arthur N.↗