Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

ASSESSMENT OF HIGH-VOLUME HARVESTED FLY ASH BLENDS FOR USE IN PRECAST CONSTRUCTION

Declining supplies of fresh fly ashes in some regions have further driven the importance of using harvested fly ash as a supplementary cementitious material and thus replacement for more energy-intensive ordinary Portland cement (OPC). Higher replacement rates of OPC with fly ash in general has traditionally been limited in precast operations due to stringent early-age strength requirements necessitated by initial prestress and lifting/handling of hardened components – often well within 24 hours after fresh concrete placement. Therefore, a series of mix designs were developed, as part of a larger framework for reassessing high-volume fly ash (HVFA) use in the context of precast construction, to demonstrate the feasibility of using larger fractions of harvested fly ash in concrete formulations suitable for precast fabrication demands. More specifically, a target minimum 24-hour compressive strength of 24.1 MPa (3500 psi) was set, in accordance with conventional precast structural design checks, while increasing the fly ash content to 40% replacement of OPC – at least a 15% increase above the traditional limit of 25%. The effect of using more sustainable Type IL cement in contrast to conventional Type III Portland cement (the traditional standard for precast use) – both in conjunction with HVFA use – was also examined. Early-age mechanical properties including compressive strength, modulus of rupture, and modulus of elasticity were evaluated within the aforementioned early-age window. Lastly, corresponding design equations were then reassessed for their applicability with respect to the high-early strength HVFA mixes examined herein.

Gombeda, Matthew J.↗
DOE OSTI2025

Structure property correlations in wet-spun textile PAN fibers for cost-effective carbon fibers applicable in H 2 storage tank manufacturing

The economic viability of high-strength carbon fibers is pivotal for their integration into Type IV compressed hydrogen storage tanks. Oak Ridge National Laboratory is advancing this objective by developing cost-effective, textile-grade polyacrylonitrile (PAN) precursor fibers through an optimized wet spinning-process to garner more microstructural control over the precursor fibers. Here, this study examines the microstructural characteristics of PAN fibers, particularly the crystalline orientation factor, and their impact on mechanical properties in both precursor and thermally converted carbon fibers (CFs). Three wet-spun PAN fibers, all having diameters of 12-13 µm but varying orientation factors were assessed. Comprehensive characterization using X-ray scattering and microscopy revealed that fibers with higher orientation factors exhibited enhanced crystallinity and optimized crystallite sizes. Mechanical testing demonstrated that the PAN fiber with the highest orientation factor achieved the greatest tensile strength (98 ksi) and modulus (1.60 Msi). Additionally optical and scanning electron microscopy confirmed smooth and defect-free surfaces across all samples. These findings indicate that manipulating spinning parameters to maximize orientation factor is more impactful in achieving high strength and modulus over factors attributed to crystallinity and crystallite sizes. Here, highest performing CFs, thermally processed in lab from textile-grade precursor averaged 558 ksi, a 10% increase over previous results.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impacts of Curing-Induced Phase Segregation in Silicon Nanoparticle-Based Electrodes

We report the investigation of silicon nanoparticle composite anodes for Li-ion batteries, using a combination of two nm-scale atomic force microscopy-based techniques: scanning spreading resistance microscopy for electrical conduction mapping and contact resonance and force volume for elastic modulus mapping, along with scanning electron microscopy-based energy dispersion spectroscopy, nanoindentation, and electrochemical analysis. Thermally curing the composite anode—made of polyethylene oxide-treated Si nanoparticles, carbon black, and polyimide binder—reportedly improves the anode electrochemical performance significantly. This work demonstrates phase segregation resulting from thermal curing, where alternating bands of carbon and silicon active material are observed. This electrode morphology is retained after extensive cycling, where the electrical conduction of the carbon-rich bands remains relatively unchanged, but the mechanical modulus of the bands decreases distinctly. These electrical and mechanical factors may contribute to performance improvement, with carbon bands serving as a mechanical buffer for Si deformation and providing electrical conduction pathways. This work motivates future efforts to engineer similar morphologies for mitigating capacity loss in silicon electrodes.

25 ENERGY STORAGE↗
DOE OSTI2024

Flax–Reinforced Vitrimer Epoxy Composites Produced via RTM

Composite laminates were produced by RTM using similar glass and flax fabrics and both vitrimer epoxy and aerospace-grade epoxy, both formulated for liquid molding. Tensile and flexural properties were measured and compared, revealing that the vitrimer composites exhibited equivalent performance in flexural strength and tensile modulus, but slightly lower performance in tensile strength relative to reference epoxy composites. In general, glass–fiber composites outperformed flax–fiber composites in tension. However, both glass and flax–fiber composites yielded roughly equivalent flexural strength and tensile modulus-to-weight ratios. Flax fabrics were recovered from composites by matrix dissolution, and a second-life laminate showed full retention of the mechanical properties relative to those produced from fresh flax. Finally, a demonstration of re-forming was undertaken, showing that simple press-forming can be used to modify the composite shape. However, re-forming to a flat configuration resulted in local fiber damage and a decrease in mechanical properties. An alternative forming method was demonstrated that resulted in less fiber damage, indicating that further refinements might lead to a viable forming and re-forming process.

Martinez, Patricio (ORCID:0000000225884389)↗
DOE OSTI2025

Enabling Industrial Re-Use of Large-Format Additive Manufacturing Molding and Tooling

Large-format additive manufacturing (LFAM) is an enabling manufacturing technology capable of producing large parts with highly complex geometries for a wide variety of applications, including automotive, infrastructure/construction, and aerospace mold and tooling. In the past decade, the LFAM industry has seen widespread use of bio-based, glass, and/or carbon fiber reinforced thermoplastic composites which, when printed, serve as a lower-cost alternative to metallic parts. One of the highest-volume materials utilized by the industry is carbon fiber (CF)-filled polycarbonate (PC), which in out-of-autoclave applications can achieve comparable mechanical performance to metal at a significantly lower cost. Previous work has shown that if this material is recovered at various points throughout the manufacturing process for both the lab and pilot scale, it can be mechanically recycled with minimal impacts on the functional performance and printability of the material while significantly reducing the feedstock costs. End-of-life (EOL) CF-PC components were processed through industrial shredding, melt compounding, and LFAM equipment, followed by evaluation of the second-life material properties. Experimental assessments included quantitative analysis of fiber length attrition, polymer molecular weight degradation using gel permeation chromatography (GPC), density changes via pycnometry, thermal performance using dynamic mechanical analysis (DMA), and mechanical performance (tensile properties) in both the X- and Z-directions. Results demonstrated a 24.6% reduction in average fiber length compared to virgin prints, accompanied by a 21% decrease in X-direction tensile strength and a 39% reduction in tensile modulus. Despite these reductions, Z-direction tensile modulus improved by 4%, density increased by 6.8%, and heat deflection temperature (HDT) under high stress retained over 97% of its original value. These findings underscore the potential for integrating mechanically recycled CF-PC into industrial LFAM applications while highlighting the need for technological innovations to mitigate fiber degradation and enhance material performance for broader adoption. This critical step toward circular material practices in LFAM offers a pathway to reducing feedstock costs and environmental impact while maintaining functional performance in industrial applications.

additive manufacturing↗
DOE OSTI2025

Glassy interphases reinforce elastomeric nanocomposites by enhancing percolation-driven volume expansion under strain

For nearly a century, introduction of nanoparticles to elastomers has yielded extraordinarily tough nanocomposites that are critical to technologies from actuators to tires. The mechanisms by which this reinforcement occurs have nevertheless remained a central open question in material science. One widely debated hypothesis posits that strong interactions between polymer and particles induce "glassy bridges" that cement particles into a cohesive percolating network that resists elongation. Here, molecular dynamics simulations show that glassy particle shells do not primarily provide elongational cohesion. Instead, they amplify an underlying mechanism wherein competition between filler and elastomer networks causes the elastomer's volume to increase on deformation. This induces contributions from the elastomer's bulk modulus, which is of order 1000 times larger than its Young's modulus. These findings establish a unified understanding of low-strain reinforcement in filled elastomers as emanating from volumetric competition between coexisting particulate and elastomeric networks. This reframes and unifies our understanding of low-strain reinforcement, provides a clear-cut diagnostic for the presence of glassy bridging, and offers a new design principle for tough elastomeric nanocomposites.

Computational Physics (physics.comp-ph)↗
DOE OSTI2025

Investigating the Effect of Water on the Mechanical Properties of Cellulose from Multiscale Molecular Dynamics Simulations

Classical molecular dynamics (MD) simulations provide insight into the structure and physicochemical properties of materials with atomic resolution. However, the length and time scales accessible to atomistic MD are orders of magnitude smaller than many relevant processes such as the response of a bulk material to experimentally accessible strain rates, which presents challenges when comparing models to experimental measurements. Bottom-up coarse-graining provides a means for systematically mapping atomistic information to lower resolution models to increase the length and time scales achievable by simulation. Cellulose is an abundant carbohydrate biopolymer with applications to many fields of research, such as materials science and renewable energy, due to its desirable mechanical properties and viability for conversion into biofuel. The effect of moisture content on the Young's modulus of cellulose is of special interest due to its native environment often being in the hydrated secondary plant cell wall and the grinding energy requirements for biomass feedstock preprocessing. The current work investigates the effects of water solvent on the Young's modulus of cellulose calculated from coarse-grained MD mechanical stress simulations. The coarse-grained model was parametrized from atomistic MD calculations of cellulose-cellulose potentials of mean force using umbrella sampling techniques under vacuum and solvated conditions. The Young's moduli of the coarse-grained cellulose assemblies parametrized from cellulose in vacuum or solvated in water were computed via mechanical stress simulations to highlight the importance of capturing solvent interactions for modeling the mechanical behavior of cellulose.

BASIC BIOLOGICAL SCIENCES,RADIATION PROTECTION AND↗
DOE OSTI2024

Investigation of acoustic waves under subsurface conditions to improve the predictions of rock mechanical properties and natural fracture characteristics

Mechanical properties and natural fracture characteristics are critical to investigate for subsurface engineering applications, including carbon storage, well drilling, and stimulation, as they govern rock stability, fluid flow, and mechanical behavior under stress. This dissertation integrates experimental and machine learning approaches to enhance the prediction and understanding of these properties by analyzing acoustic wave behavior under varied subsurface conditions. First, the influence of temperature, pore pressure, and supercritical CO2 (scCO2) saturation on poroelastic properties is examined using Gray Berea sandstone samples. The results show that temperature and pore pressure significantly affect the bulk modulus and Biot’s coefficient, while scCO2 saturation impacts rock compressibility, informing strategies for effective geological carbon storage. The study extends this understanding by experimentally evaluating the impact of reservoir depletion on the dynamic mechanical properties of the emerging Caney shale in South Oklahoma with the employment of unsupervised machine learning to predict static mechanical properties across the Caney shale. Integrating petrophysical data and chemostratigraphy, the workflow—featuring K-means clustering, principal component analysis (PCA), and inverse distance weighting (IDW)—improves stratigraphic characterization and the estimation of static-to-dynamic modulus ratios, which is vital for optimizing drilling and stimulation strategies. Finally, the work explores how natural fracture characteristics in shale influence acoustic waveforms and shear wave splitting (SWS) analysis. Experimental data on fractured samples under different stress and temperature conditions, combined with machine learning models such as K-nearest neighbors (KNN) and extreme gradient boosting (XGBoost), reveal key fracture properties impacting SWS and wave propagation. Together, these studies provide a comprehensive framework for linking acoustic wave behavior with rock properties, advancing the methods for monitoring and predicting geomechanical changes. The insights offered valuable implications for safer, more efficient CO2 injection, hydrocarbon extraction, and subsurface management.

Elkholy, Sherif↗
DOE OSTI2026

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗
DOE OSTI2024

Analysis of differential scanning calorimetry data for aged plutonium

Differential scanning calorimetry data for samples of a 52 year old plutonium alloy with 3.3 at. % Ga that were heated beyond the melting point is analyzed using transition state theory to find activation energies for the δ to ε and ε to liquid phase transitions. A Bayesian statistical method involving a Gaussian process model is used to find mean values and confidence intervals for the activation energies. The activation energy for the δ to ε phase transition increases by 3.3 ± 3.8% per decade, relative to the case when all age related plutonium lattice point defects have been removed through annealing. The corresponding increase in activation energy for the ε to liquid transition is shown to be 7.1 ± 1.8% per decade. It is postulated that the change in activation energy with age for both phase transitions is caused, in part, by the accumulation of the same type of lattice point defects associated with the observed increase in elastic bulk modulus over time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Experimental and computational studies on high-entropy carbide MoNbTaVWC 5 under high pressures

High-entropy carbide, MoNbTaVWC 5 , was synthesized from oxide precursors of the constituent metals, mixed with graphite powder in a microwave-generated hydrogen plasma at 26.66 kPa and 2100 °C. Ambient x-ray diffraction analysis confirms the full conversion of oxide precursors into a single-phase, face-centered cubic structure with a lattice parameter a = 4.3309 Å. Nanoindentation measured a hardness of 24.5 ± 1.3 GPa and an elastic modulus of 386 ± 22 GPa. The synthesized sample, mixed with a copper pressure marker, was studied by the radial x-ray diffraction technique with beryllium gasketing in a diamond anvil cell up to 70 GPa. The experimentally measured pressure–volume curve and shear strength were compared with theoretical predictions using the special quasi-random structure technique and density functional theory. MoNbTaVWC 5 achieved a 12% volume compression at 70 GPa and exhibited a high shear strength of 6.6 GPa. The present study demonstrates that the high-entropy carbide MoNbTaVWC 5 exhibits exceptional incompressibility and high strength under extreme conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Response functions and giant monopole resonances for light to medium-mass nuclei from the ab initio symmetry-adapted no-core–shell model

Using the ab initio symmetry-adapted no-core–shell model, we compute sum rules and response functions for light to medium-mass nuclei, starting from interactions that are derived in the chiral effective field theory. Specifically, we investigate electromagnetic transitions of monopole, dipole and quadrupole nature for 4 He, and explore dominant features of giant monopole resonances in symmetric nuclei such as the closed-shell 4 He and 16 O light nuclei, the intermediate-mass open-shell 20 Ne and the medium-mass closed-shell 40 Ca. Furthermore, for the NNLO opt chiral potential, we determine parameter-free monopole sum rules, which can provide information on the incompressibility of symmetric nuclear matter. Here, we report 213(10) MeV as an estimate for the compression modulus for infinite nuclear matter, which overlaps with the lower range of values often used in current astrophysical applications.

ab initio nuclear structure↗
DOE OSTI2024

On the length scale and rate-dependent mechanical behavior of monolithic (oxy)sulfidic glassy solid-state electrolytes

In the controlled atmosphere of a dedicated glove box, nanoindentation performed with a diamond Berkovich indenter tip has been used to examine the mechanical behavior of three (oxy)sulfide solid-state electrolytes (SSEs), 70Li 2 S·(30–x)P 2 S 5 ·xP 2 O 5 (x = 0, 2, and 5). At a drive frequency of 120 Hz, the elastic modulus is found to be predominantly depth independent over the range of 100 nm to 1 μm and generally insensitive to the varying mol fraction of oxygen (0, 2, and 5%) as well as the imposed strain rates of 0.025, 0.05, and 0.1 1/s. All three SSEs exhibit significant room-temperature creep. Strain burst activity observed during loading (potentially representative of pore collapse or cracking) is attenuated with the addition of oxygen. The hardness is found to be insensitive to the imposed strain rates but varying with depth and oxygen content. Furthermore, the highest oxygen concentration yields the lowest hardness and strongest depth dependence.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sound Velocities in Vanadium Reveal Complex Elastic Behavior at High Pressures

Compressional (VP) and shear (VS) wave velocities of polycrystalline vanadium were measured simultaneously up to 11.5 GPa at room temperature using ultrasonic interferometry in a multi-anvil press. Complex softening behavior in VS and resulting shear moduli are discovered, possibly revealing a precursor to the reported phase transition within 30–60 GPa. The current data enables a comprehensive assessment of the elastic and mechanical properties of vanadium at high pressures, including bulk and shear moduli, Young’s modulus, Poisson’s ratio, and Pugh’s ratio. Through fitting to the 3rd-order finite strain equations, the elastic moduli and their pressure derivatives were determined to be K S0 = 151 (2) GPa, G 0 = 46.9 (8) GPa, K$^{’}_{S0}$ = 3.47 (5), and G$^{’}_{0}$ = 0.62 (1). These experimental results allow us to compare with and benchmark the existing Steinberg–Guinan models for extrapolations to extreme pressure and temperature conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of Zn Addition on Phase Evolution in AlCrFeCoNiZn High–Entropy Alloy

The addition of Zn to AlCrFeCoNi high-entropy alloy (HEA) poses intriguing questions as to how it would affect phase evolution. Herein, the phase evolution in AlCrFeCoNiZn is studied using a combination of experimental techniques (X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, and differential scanning calorimetry) and computational (density-functional theory [DFT], calculation of phase diagrams, and machine-learning) methods. Mechanically alloyed and spark-plasma-sintered AlCrFeCoNiZn assumes a metastable single-phase, body-centered-cubic (BCC) structure that undergoes diffusion-controlled phase separation upon subsequent heat treatment to form separate (Al, Cr)-rich, (Fe, Co)-rich, and (Zn, Ni)-rich phases. The formation of (Al, Cr)-rich phase, not reported previously in AlCrFeCoNi-based HEAs, is attributed to strong clustering tendency of Cr–Zn and Cr–Ni pairs, combined with the strong ordering of Zn–Ni pair, driving out Cr that in turn combines with Al to form a (Al, Cr)-rich phase. In the DFT results, the formation of thermodynamically stable L1 2 phase is shown wherein Cr–Fe–Zn [Al–Ni-Co] preferably occupy1a (000) [3c (0 ½ ½)] positions. Furthermore, the sluggish diffusional transformation to L1 2 phase from BCC precursors is attributed to the small stacking-fault energy of AlCrFeCoNiZn. The equilibrated HEA exhibits a high microhardness of 8.24 GPa with an elastic modulus of 184 GPa.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermoplastic Elastomers and Their Physical Gels Electrospun into Tunable Microfibrous Nonwoven Mats: Structure Formation and Property Enhancement

Abstract Thermoplastic elastomers (TPEs) based on styrenic block copolymers constitute excellent examples of self‐networking macromolecules that are employed in a wide range of contemporary technologies as molded parts. In such applications, these TPEs exist as dense (nonporous) films or other shapes. Here, it is first demonstrated that a series of commercial TPEs possessing comparable compositions can be electrospun from solution to form microfibers that are arranged into nonwoven mats that are breathable. An important consideration for microfiber formation is the copolymer molecular weight, which regulates i) the viscosity of the parent solution prior to electrospinning, ii) the ability of these copolymers to self‐assemble during electrospinning, iii) the microfiber morphology, and iv) the mechanical properties of the resultant microfibers. The addition of a midblock‐selective aliphatic oil to these TPEs yields thermoplastic elastomer gels (TPEGs), wherein the copolymer morphology and mechanical properties become highly composition‐tunable. Electrospinning TPEGs from a binary oil+solvent solution introduces a micelle inversion mechanism that begins with an oil‐rich micellar core and ends with a styrene‐rich micellar core, required for network stabilization, as the solvent dries during microfiber solidification. This work has implications for the production of controllably low‐modulus microfibrous materials possessing modestly improved toughness but exceptional extensibility and enhanced optical transparency.

Shamsi, Mohammad↗
DOE OSTI2024

Mechanically Reinforced Pseudosolid Polyelectrolyte Membranes via Layer-by-Layer Assembly for High-Performing Lithium-Metal Batteries

Ionogels are emerging as high-potential pseudosolid electrolytes for lithium-metal batteries (LMBs), leveraging their intrinsic high ionic conductivity from entrapped ionic liquid (IL) electrolytes. However, their practical application is hindered by poor mechanical strength stemming from the confinement of ILs within a polymer matrix. To address this challenge, the formation of conformal polyion coatings with functional groups is reported to be relevant to LMBs’ application on ionogels, utilizing a layer-by-layer (LbL) assembly strategy. Here, this approach significantly enhances the mechanical strength (Young's modulus and tensile strength) and electrochemical performance of ionogels, owing to the tailored interface modifications introduced by functional groups’ specific conformal polyion coatings. The core of this methodology leverages the inherent ionic structure of ionogels to enable facile interface modification through Coulombic interactions between polyanions and polycations. These conformally coated interface functionalized membranes show improved electrochemical performance when integrated with cathode materials such as LiFePO 4 (LFP) and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) in an LMB configuration, underscoring their potential for robust, high-conductivity, pseudosolid membranes for LMB applications. These innovative pseudosolid membranes offer improved mechanical and electrochemical properties, leading to higher battery efficiency and safety, making them promising candidates for next-generation LMB technology.

25 ENERGY STORAGE↗
DOE OSTI2024

Additive Manufacturing with Cellulose-Based Composites: Materials, Modeling, and Applications

Recent advances in large-scale additive manufacturing (AM) with polymer-based composites have enabled efficient production of high-performance materials. Cellulose nanomaterials (CNMs) have emerged as bio-based feedstocks due to their exceptional strength and sustainability. However, challenges such as hornification and poor dispersion in polymer matrices still limit large-scale CNM–polymer composite manufacturing, requiring novel strategies. Here, this review outlines an approach starting with atomic-level simulations to link molecular composition to key parameters like bulk density, viscosity, and modulus. These simulations provide data for finite element analysis (FEA), which informs large-scale experiments and reduces the need for extensive trials. The strategy explores how atomic interactions impact the morphology, adhesion, and mechanical properties of CNM-based composites in AM processes. The review also discusses current developments in AM, along with predictions of mechanical and thermal properties for structural applications, packaging, flexible electronics, and hydrogel scaffolds. By integrating experimental findings with molecular dynamics (MD) simulations and finite element modeling (FEM), valuable insights for material design, process optimization, and performance enhancement in CNM-based AM are provided to address ongoing challenges.

36 MATERIALS SCIENCE↗