Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microsegregation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

77 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Flight Experiment to Study Double-Diffusive Instabilities in Silver-Dopped Lead Bromide Crystals

The main objective of the present program is to understand thermosolutal convection during crystal growth of PbBr2-AgBr alloys. This involves identification of the growth conditions for microgravity experiments delineating the microsegregation, observation of convecto-diffusive instabilities and comparison with theoretical models. The overall objectives can be summarized as follows: 1. Observe and study the double diffusive and morphological instabilities in controlled conditions and to compare with theoretically predicted convective and morphological instability curves. 2. Study the three-dimensional morphological instabilities and resulting cellular growth that occur near the onset of morphological instability in the bulk samples under purely diffusive conditions. 3. Understand the micro-and macro-segregation of silver dopant in lead bromide crystals in microgravity. 4. Provide basic data on convective behavior in alloy crystals grown by the commercially important Bridgman crystal growth process.

Singh, N. B.↗
NASA NTRS2001

Simulation of the Effect of Realistic Space Vehicle Environments on Binary Metal Alloys

Simulations that assess the effect of space vehicle acceleration environments on the solidification of Pb-Sb alloys are reported. Space microgravity missions are designed to provide a near zero-g acceleration environment for various types of scientific experiments. Realistically. these space missions cannot provide a perfect environment. Vibrations caused by crew activity, on-board experiments, support systems stems (pumps, fans, etc.), periodic orbital maneuvers, and water dumps can all cause perturbations to the microgravity environment. In addition, the drag on the space vehicle is a source of acceleration. Therefore, it is necessary to predict the impact of these vibration-perturbations and the steady-state drag acceleration on the experiments. These predictions can be used to design mission timelines. so that the experiment is run during times that the impact of the acceleration environment is acceptable for the experiment of interest. The simulations reported herein were conducted using a finite element model that includes mass, species, momentum, and energy conservation. This model predicts the existence of "channels" within the processing mushy zone and subsequently "freckles" within the fully processed solid, which are the effects of thermosolutal convection. It is necessary to mitigate thermosolutal convection during space experiments of metal alloys, in order to study and characterize diffusion-controlled transport phenomena (microsegregation) that are normally coupled with macrosegregation. The model allows simulation of steady-state and transient acceleration values ranging from no acceleration (0 g). to microgravity conditions (10(exp -6) to 10(exp -3) g), to terrestrial gravity conditions (1 g). The transient acceleration environments simulated were from the STS-89 SpaceHAB mission and from the STS-94 SpaceLAB mission. with on-orbit accelerometer data during different mission periods used as inputs for the simulation model. Periods of crew exercise, quiet (no crew activity), and nominal conditions from STS-89 were used as simulation inputs as were periods of nominal. overboard water-dump, and free-drift (no orbit maneuvering operations) from STS-94. Steady-state acceleration environments of 0.0 and 10(exp -6) to 10(exp -1) g were also simulated, to serve as a comparison to the transient data and to assess an acceptable magnitude for the steady-state vehicle drag

Westra, Douglas G.↗
DOE OSTI2022

USE OF TWO-PISTON SPLAT QUENCHING TO INVESTIGATE & CHARACTERIZE THE IMPACT OF COMPOSITIONAL VARIATIONS ON RAPID SOLIDIFICATION MICROSTRUCTURES & SUB-MICROSCALE FEATURES IN STAINLESS STEEL ALLOY.

The objective of this dissertation was to use two-piston splat quenching (SQ) to investigate the impact of compositional modifications on the solidification and microstructure of rapidly solidified austenitic stainless steels (SS) and to demonstrate the ability of SQ to quickly and effectively simulate rapid solidification conditions similar to those found in powder bed fusion (PBF) additive techniques. PBF techniques like laser powder bed fusion (LPBF) are being implemented across a breadth of research and industrial applications to create parts with complex geometries and performance capabilities while pushing the current limits of processing conditions and understanding of material systems. In this work, SQ was used to experimentally produce rapid solidification in 20+ unique austenitic SS compositions with systematic variations of the chrome and nickel equivalency ratio (Cr/Nieq) through targeted compositional modifications. From the targeted change of Cr, Ni, and Mo concentrations in rapidly solidified SS alloys, the ferrite solidification mode was found to be the primary solidification mode at significantly lower Cr/Nieq than previously predicted for RS. Also, decreasing concentrations of Fe at a constant Cr/Nieq ratio (i.e., different Fe isopleths), or increased Mo concentrations at a constant Cr/Nieq ratio were found to suppress the ferrite to austenite massive transformation when compared to alloys with lower concentrations at the same Cr/Nieq. Using an established empirical relationship between cell size and cooling rate, the SQ technique was estimated to produce cooling rates between 106 and 108 K/s. Thermal gradients were extracted from 2-D heat transfer simulations of the SQ solidification event and used with these cooling rates to produce solidification rate estimates for SQ which were between 0.4-1.6m/s. The primary solidification mode was observed to be the determining factor in which elements segregated to the cell boundaries during RS, for which Cr and Mo were the main elements to segregate during primary austenite solidification and Ni during primary ferrite solidification. Finally, the solidification rates and conditions produced by SQ experiments resulted in similar microstructures, features, and microsegregation to what was found in LPBF samples of the same feedstock.

Hasenbusch, Zachary↗
DOE OSTI2023

Corrosion testing needs and considerations for additively manufactured materials in nuclear reactors

Metal additive manufacturing holds significant promise as an enabling technology for the 21st century nuclear energy industry. Metal additive manufacturing (MAM) can allow the fabrication of novel materials and innovative component designs that are not achievable through conventional manufacturing. Due to its very different fabrication methods, as-fabricated MAM components are characteristically different from conventionally manufactured components. MAM materials exhibit very different microstructures from conventional cast or wrought materials. For example, austenitic stainless steels fabricated by laser powder bed fusion exhibit columnar grain structures, dislocation cell structures, and melt pool fingerprints. In addition, MAM fabrication may result in defects such as porosity, incomplete processing of the feedstock (e.g., lack of fusion in melt-based methods), and oxide inclusions. Heat treatments may further evolve the microstructure, microsegregation, and stresses within the component. Furthermore, MAM components have a rough surface with feature sizes on the order of the feedstock material, as opposed to smooth surfaces resulting from conventional machining and forming operations. As a result, the corrosion behavior of MAM components will likely be significantly different from that of conventionally formed components. Corrosive environments for structural materials within advanced reactor environments include molten fluoride and chloride salts, liquid sodium and lead-bismuth, and high-temperature helium. The Advanced Materials and Manufacturing Technologies program within the Department of Nuclear Energy in the United States Department of Energy is assessing the unique concerns of MAM component corrosion and testing methodologies in advanced nuclear reactor environments. We discuss these concerns and testing strategies in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Prediction of microstructure formation in laser powder bed fusion process.

The datasets are results analyzing the predicted microstructures in a single track during the laser powder bed fusion additive manufacturing process. They are the outputs by running the opensource code, muMatScale (The code can be cited at: Yuan, Lang, Fattebert, Jean-Luc, and Sabau, Adrian. (2023, August 03). muMatScale. [Computer software]. https://github.com/lang-yuan/muMatScale. https://doi.org/10.11578/dc.20240112.2.) For each set of data, it contains the time-dependent information of Temperature, Fraction Solid, Grain ID, Grain Angle ( crystallographic orientations by Euler angles), and solute Composition. The dataset can be visualized by Paraview (https://www.paraview.org/ ). The 6 datasets are: 1. Baseline_base1_n4e14_dt20: baseline case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 2. Nuc_n4e15_dt20: case with bulk nucleation density of 4E+15/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 3. Nuc_n4e15_dt50: case with bulk nucleation density of 4E+15/m^3, undercooling of 50K, substrate nucleation density of 1.5E+15/m^3 4. Nuc_n6e15_dt20: case with bulk nucleation density of 4E+16/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 5. Base4_n4e14_dt20: case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 6.0E+15/m^3 6. Base16_n4e14_dt20: case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 2.4E+16/m^3

36 MATERIALS SCIENCE↗