Delta Wind Mating to Upper Stage at PHSF
Footage shows the mating of the Delta Wind to the Upper Stage rocket engine at the Payload Hazardous Servicing Facility (PHSF).
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Footage shows the mating of the Delta Wind to the Upper Stage rocket engine at the Payload Hazardous Servicing Facility (PHSF).
This NASA Kennedy Space Center video release presents footage of the mating of NASA's WIND payload to the Delta launch vehicle at Cape Canaveral Air Station's complex 17B. The video includes shots of the workcrews as well as wide angle views of the spacecraft in its launching position. WIND was launched on November 1, 1994 and is the first of two NASA spacecraft in the Global Geospace Science initiative and part of the International Solar Terrestrial Physics (ISTP) Project.
This NASA Kennedy Space Center (KSC) video release presents footage of the lift and mate of NASA's X-ray Timing Explorer (XTE) to a McDonnell Douglas Delta II rocket at Launch Complex 17A, Cape Canaveral Air Station. The video includes shots of the workcrews as well as wide angle views of the spacecraft in its launching position. The XTE was launched into a circular orbit with an altitude of 600 km and an inclination of 23 degrees on Dec. 30, 1995.
Footage shows the mating of the Tethered Satellite System (TSS) to the Deployer.
The International Space Station (ISS) Pressurized Mating Adapters (PMAs) Environmental Control and Life Support (ECLS) System is comprised of three subsystems: Atmosphere Control and Supply (ACS), Temperature and Humidity Control (THC), and Water Recovery and Management (WRM). PMA 1 and PMA 2 flew to ISS on Flight 2A and PMA 3 flew to ISS on Flight 3A. This paper provides a summary of the PMAs ECLS design and the detailed Element Verification methodologies utilized during the Qualification phase for the PMAs.
While in space silicone based elastomer seals planned for use on NASA's Crew Exploration Vehicle (CEV) are exposed to threats from micrometeoroids and orbital debris (MMOD). An understanding of these threats is required to assess risks to the crew, the CEV orbiter, and missions. An Earth based campaign of hypervelocity impacts on small scale seal rings has been done to help estimate MMOD threats to the primary docking seal being developed for the Low Impact Docking System (LIDS). LIDS is being developed to enable the CEV to dock to the ISS (International Space Station) or to Altair (NASA's next lunar lander). The silicone seal on LIDS seals against aluminum alloy flanges on ISS or Altair. Since the integrity of a seal depends on both sealing surfaces, aluminum targets were also impacted. The variables considered in this study included projectile mass, density, speed, incidence angle, seal materials, and target surface treatments and coatings. Most of the impacts used a velocity near 8 km/s and spherical aluminum projectiles (density = 2.7 g/cubic centimeter), however, a few tests were done near 5.6 km/s. Tests were also performed using projectile densities of 7.7, 2.79, 2.5 or 1.14 g/cubic centimeter. Projectile incidence angles examined included 0 degrees, 45 degrees , and 60 degrees from normal to the plane of the target. Elastomer compounds impacted include Parker's S0383-70 and Esterline's ELA-SA-401 in the as received condition, or after an atomic oxygen treatment. Bare, anodized and nickel coated aluminum targets were tested simulating the candidate mating seal surface materials. After impact, seals and aluminum plates were leak tested: damaged seals were tested against an undamaged aluminum plate; and undamaged seals were placed at various locations over craters in aluminum plates. It has been shown that silicone elastomer seals can withstand an impressive level of damage before leaking beyond allowable limits. In general on the tests performed to date, the diameter of the crater in either the elastomer, or the aluminum, must be at least as big as 80% to 90% of width of the bulb of the seal before significant leakage occurs.
Teams participating in the 2006 ROV competition organized by the Marine Advanced Technology Education (MATE) Center and the Marine Technology Society's (MTS) ROV Committee experienced first-hand the scientific and technical challenges that many ocean scientists, technicians, and engineers face every day. The competition tasked more than 1,000 middle and high school, college, and university students from Newfoundland to Hong Kong with designing and building ROVs to support the next generation of ocean observing systems. Teaming up with the National Office for Integrated and Sustained Ocean Observations, Ocean. US, and the Ocean Research Interactive Observatory Networks (ORION) Program, the competition highlighted ocean observing systems and the careers, organizations, and technologies associated with ocean observatories. The student teams were challenged to develop vehicles that can deploy, install, and maintain networks of instruments as well as to explore the practical applications and the research questions made possible by observing systems.
While in space silicone based elastomer seals planned for use on NASA's Crew Exploration Vehicle (CEV) are exposed to threats from micrometeoroids and orbital debris (MMOD). An understanding of these threats is required to assess risks to the crew, the CEV orbiter, and missions. An Earth based campaign of hypervelocity impacts on small scale seal rings has been done to help estimate MMOD threats to the primary docking seal being developed for the Low Impact Docking System (LIDS). LIDS is being developed to enable the CEV to dock to the ISS (International Space Station) or to Altair (NASA's next lunar lander). The silicone seal on LIDS seals against aluminum alloy flanges on ISS or Altair. Since the integrity of a seal depends on both sealing surfaces, aluminum targets were also impacted. The variables considered in this study included projectile mass, density, speed, incidence angle, seal materials, and target surface treatments and coatings. Most of the impacts used a velocity near 8 km/s and spherical aluminum projectiles (density = 2.7 g/cubic cm), however, a few tests were done near 5.6 km/s. Tests were also performed using projectile densities of 7.7, 2.79, 2.5 or 1.14 g/cubic cm. Projectile incidence angles examined included 0 deg, 45 deg, and 60 deg from normal to the plane of the target. Elastomer compounds impacted include Parker's S0383-70 and Esterline's ELA-SA-401 in the as received condition, or after an atomic oxygen treatment. Bare, anodized and nickel coated aluminum targets were tested simulating the candidate mating seal surface materials. After impact, seals and aluminum plates were leak tested: damaged seals were tested against an undamaged aluminum plate; and undamaged seals were placed at various locations over craters in aluminum plates. It has been shown that silicone elastomer seals can withstand an impressive level of damage before leaking beyond allowable limits. In general on the tests performed to date, the diameter of the crater in either the elastomer, or the aluminum, must be at least as big as 80% to 90% of width of the bulb of the seal before significant leakage occurs.
This paper presents Proof Mate, an interactive proof helper for the PVS verification system. The helper is integrated in VSCode-PVS, the Visual Studio Code extension for PVS. It extends the capabilities of VSCode-PVS by introducing new functionalities for suggesting proof commands, sketching proof attempts, and repairing broken proofs during interactive proof sessions. This work further aligns VSCode-PVS to the functionalities provided by modern development tools, with the ultimate aim to facilitate the adoption of formal methods in engineering practices and education.
This paper presents Proof Mate, an interactive proof helper for the PVS verification system. The helper is integrated in VSCode-PVS, the Visual Studio Code extension for PVS. It extends the capabilities of VSCode-PVS by introducing new functionalities for suggesting proof commands, sketching proof attempts, and repairing broken proofs during interactive proof sessions. This work further aligns VSCode-PVS to the functionalities provided by modern development tools, with the ultimate aim to facilitate the adoption of formal methods in engineering practices and education.
A system or method for a magnetic self-aligning coupling device for a fiber optic cable. The device includes a first end coupling comprising a first magnet and a second magnet. Both magnets include a mating surface and an annular ring defining an axial aperture. The aperture receives a distal end of a segment of fiber optic cable in a tight fit. The fiber optic cable has an exterior sleeve and a fiber core. The fiber core of the first segment and the second segment of the fiber optic cable are axially aligned by magnetic force in the first and second apertures to create a continuous fiber optic path. A method for detecting a security breach of a door using the self-aligning couplings is also described.
A system or method for a magnetic self-aligning coupling device for a fiber optic cable. The device includes a first end coupling comprising a first magnet and a second magnet. Both magnets include a mating surface and an annular ring defining an axial aperture. The aperture receives a distal end of a segment of fiber optic cable in a tight fit. The fiber optic cable has an exterior sleeve and a fiber core. The fiber core of the first segment and the second segment of the fiber optic cable are axially aligned by magnetic force in the first and second apertures to create a continuous fiber optic path. A method for detecting a security breach of a door using the self-aligning couplings is also described.
Not Available
Not Available
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Chromium carbon nitride coatings have potential industrial applications in aqueous environments due to their good tribological properties and corrosion resistance. In order to reveal the effect of silicon doping on the tribological properties of CrCN coating, the tribological properties of Cr(Si)CN coatings sliding against potential sliding partners (Si{sub 3}N{sub 4}, Al{sub 2}O{sub 3} and SUS440C balls) in water were discussed. The results showed that the coefficient of friction (COF) for different partners could be arranged as μ{sub Al2O3} < μ{sub Si3N4} < μ{sub SUS440C} regardless of coatings. This result was determined by the tribochemical reaction, oxidation resistance and contact pressures of tribopairs. After the incorporation of Si element, the friction behavior of CrCN coating was improved due to the friction-induced hydration of amorphous silicon compound phase as sliding against Si{sub 3}N{sub 4} and SUS440C balls.
Not Available