Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Investigation of plasma characteristics in an unbalanced magnetron sputtering system

Results are presented from experimental studies of a magnetron sputtering system for different configurations of the magnetic field above the cathode surface. The current-voltage characteristics of a magnetron discharge at different working gas pressures (0.08-0.3 Pa) and currents in the unbalancing coil were studied. The production and transport of charge carriers in a magnetron discharge with an unbalanced magnetic field was investigated by means of probe measurements of plasma characteristics and ion energies in the region between the substrate and the magnetic trap at the cathode surface. The radial distributions of the ion current density, plasma potential, and floating potential in the unbalanced operating mode are found to have pronounced extrema at the magnetron axis. It is shown that the plasma density near the substrate can be increased considerably when the axial magnetic field is high enough to efficiently confine plasma electrons and prevent their escape to the chamber wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recirculating planar magnetrons: simulations and experiment

The Recirculating Planar Magnetron (RPM) is a novel crossed-field device whose geometry is expected to reduce thermal load, enhance current yield as well as ease the geometric limitations in scaling to high RF frequencies as compared to the conventional cylindrical magnetrons. The RPM has two different adaptations: A. Axial B field and radial E field; B. Radial B field and axial E field. The preliminary configuration (A) to be used in experiments at the University of Michigan consists of two parallel planar sections which join on either end by cylindrical regions to form a concentric extruded ellipse. Similar to conventional magnetrons, a voltage across the AK gap in conjunction with an axial magnetic field provides the electrons with an ExB drift. The device is named RPM because the drifting electrons recirculate from one planar region to the other. The drifting electrons interact with the resonantly tuned slow wave structure on the anode causing spoke formation. These electron spokes drive a RF electric field in the cavities from which RF power may be extracted to Waveguides. The RPM may be designed in either a conventional configuration with the anode on the outside, for simplified extraction, or as an inverted magnetron with the anode at the inner conductor, for fast start-up. Currently, experiments at the Pulsed Power and Microwave Laboratory at the University of Michigan are in the setup and design phase. A conventional RPM with planar cavities is to be installed on the Michigan Electron Long Beam Accelerator (MELBA) and is anticipated to operate at -200kV, 0.2T with a beam current of 1-10 kA at 1GHz. The conventional RPM consists of 12 identical planar cavities, 6 on each planar side, with simulated quality factor of 20.

43 PARTICLE ACCELERATORS↗

On the evolution of film roughness during magnetron sputtering deposition

The effect of long-range screening on the surface morphology of thin films grown with pulsed-dc (p-dc) magnetron sputtering is studied. The surface evolution is described by a stochastic diffusion equation that includes the nonlocal shadowing effects in three spatial dimensions. The diffusional relaxation and the angular distribution of the incident particle flux strongly influence the transition to the shadowing growth regime. In the magnetron sputtering deposition the shadowing effect is essential because of the configuration of the magnetron system (finite size of sputtered targets, rotating sample holder, etc.). A realistic angular distribution of depositing particles is constructed by taking into account the cylindrical magnetron geometry. Simulation results are compared with the experimental data of surface roughness evolution during 100 and 350 kHz p-dc deposition, respectively.

36 MATERIALS SCIENCE↗

A cookbook for building a high-current dimpled H – magnetron source for accelerators

A high-current (>50 mA) dimpled H – magnetron source has been built at Fermilab for supplying H – beam to the entire accelerator complex. Despite many decades of expertise with slit H – magnetron sources at Fermilab, we were faced with many challenges from the dimpled H – magnetron source, which needed to be overcome in order to make it operational. Dimpled H – sources for high-energy physics are not new: Brookhaven National Laboratory has operated a dimpled H- source for more than two decades. However, the transference of that experience to Fermilab took about two years because a cookbook for building this type of source did not exist and seemingly innocuous or undocumented choices had a huge impact on the success or failure for this type of source. Moreover, it is the goal of this paper to document the reasons for these choices and to present a cookbook for building and operating dimpled H – magnetron sources.

43 PARTICLE ACCELERATORS↗

Preferential growth of helium-doped Ti films deposited by magnetron sputtering

The authors present a study on the influence of the bias voltages on the preferred orientation and microstructure of helium-doped Ti films. The films were deposited in a vacuum chamber by both direct-current magnetron sputtering and electron-cyclotron-resonance plasma-aided magnetron sputtering (ECR-PMS) methods. The preferred orientation and microstructure of the films were analyzed by x-ray diffraction (XRD) and transmission electron microscopy. They found that the preferred crystal orientation of helium-doped Ti films was controllably varied from (002) to (100) orientation by increasing the bias voltage (i.e., ion bombardment current and energy). The dominant bombardment effect on the orientation was from the Ar ions of the anode sheath in the magnetron sputtering plasma, and He bombardment also showed a slight influence on the orientation transformation at low trapped-helium content in the crystal. The XRD peak broadening of helium-doped Ti films prepared by ECR-PMS is much more serious than for conventional magnetron sputtering even at low helium concentrations. It is believed that asynchronous bombardment from He ions in the ECR plasma area and Ar ions in the deposition plasma during film growth significantly decreases the mobility of Ti adatoms on the surface and enhances the growth of helium-induced defects, thus increasing the crystal disorder and influencing the crystal orientation transformation. On the contrary, the sequential bombardment of He and Ar particles can decrease helium-dissolution produced defects and improve crystallization.

36 MATERIALS SCIENCE↗

High-Power Magnetron Transmitter for the Electron Collider Ring of the MEIC Facility

Operation of the 3-12 GeV electron collider 8-shape ring of the MEIC facility causes a Synchrotron Radiation (SR) of electrons in arcs with energy loss of ~20 kW/m at beam current of ~3 A. The total SR loss up to 2 MW per a revolution is presumed to compensate by Superconducting RF (SRF) accelerating cavities. To minimize the beam emittance, each individual SRF cavity is proposed to feed by an individual and independent RF source allowing a wide-band control in phase and power. Most efficient and less expensive in capital and maintenance costs the high-power transmitters based on magnetrons, injection-locked by phase-modulated signals, controlled in wide-band are proposed as the RF sources. The magnetron RF sources utilizing 2-cascade magnetrons allowing a wide-band phase and power control by the injection-locking phase-modulated signals were experimentally modelled by 2.45 GHz, CW, 1 kW magnetrons. Results of the modelling and adequacy of the transmitters for the SRF cavities are discussed in the presented article.

Kazakevich, Grigory↗

Magnetron R&Ds for High Efficiency CW RF Sources of Particle Accelerators

A proof of principle experiment carried out at JLab's magnetron R&D test stand has demonstrated a -25dB injection signal to phase lock a 2.45GHz 1.2kW CW magnetron within 2.1 Hz of root mean square deviation (RMSD) value with the optimization of magnetic field trimming of ±25% in order to overcome the frequency pushing of more than 4MHz in the RF power output range of 45-100%. In addition, a test stand for a newly built 1497 MHz, 13kW, CW magnetron prototype is ready for the high power injection test with outcome aimed for the CEBAF klystron replacement. Based on these R&D results, a 915MHz, 2?75kW CW commercial heating type magnetron system is being developed as high efficiency (>80%) RF source to drive an electron linac for industrial applications.

Wang, H.↗

A Novel Technique for Pulsed Operation of Magnetrons without Modulation of Cathode Voltage

Modern pulsed superconducting accelerators of megawatt beams require efficient RF sources controllable in phase and power. For each Superconducting RF (SRF) cavity is desirable a separate RF source with power up to hundreds of kW with pulse duration in the millisecond range. The efficiency of the traditional RF sources (klystrons, IOTs, solid-state amplifiers) is lower than that of the magnetrons, while the cost of a unit of RF power is much higher. Therefore the magnetron-based RF sources would significantly reduce the capital and operation costs in comparison with the traditional RF sources. A recently developed an innovative technique makes possible the pulsed generation of magnetrons powered below the self-excitation threshold voltage. This technique does not require pulse modulators to form RF pulses. The magnetron operation in this regime is stable, low noise, controllable in phase and power, and provides higher efficiency than other types of RF power sources. It allows operation in pulsed modes with large duty factor. The developed technique and its experimental verification are considered and discussed.

43 PARTICLE ACCELERATORS↗

Fabrication of Nb3Sn by Magnetron Sputtering for Superconducting Radiofrequency Application

Particle accelerators are considered as an important device that has wide applications in cancer treatment, sterilizing waste, preserving foods, ion implantation in semiconductor industry, and in production of isotopes for medical applications. Superconducting radiofrequency (SRF) cavities are the building blocks of a linear particle accelerator. Current particle accelerators use niobium (Nb) superconductors as the sheet material to fabricate a single SRF cavity for particle acceleration. With better superconducting properties (critical temperature Tc ~ 18.3 K, superheating field Hsh~ 400 mT), Nb3Sn is considered a potential candidate in SRF technology. Magnetron sputtering is a promising deposition method to fabricate Nb3Sn thin films inside SRF cavities. Superconducting Nb3Sn films were fabricated on Nb and sapphire substrates by magnetron sputtering from a single stoichiometric Nb3Sn target, by multilayer sputtering of Nb and Sn followed by annealing, and by co-sputtering of Nb and Sn followed by annealing. The variation of morphological and superconducting properties was investigated for different substrate temperatures, annealing temperatures, annealing durations, and thicknesses. The film properties were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy dispersive X-ray spectroscopy (EDS). The films had crystalline Nb3Sn structure without any presence of poor superconducting Nb6Sn5 and NbSn2 phases. The highest Tc of the films fabricated from the stoichiometric target, multilayer sputtering and co-sputtering were 17.44, 17.93, and 17.66 K respectively. Finally, a cylindrical sputter coater with two identical magnetrons was designed and commissioned to fabricate Nb3Sn films inside a 2.6 GHz SRF cavity. The magnetrons were installed facing opposite to each other in a custom designed vacuum chamber and multilayers of Nb and Sn films on 1 cm2 Nb substrates replicating the beam tubes and equator locations of the cavity and the coated multilayered films were annealed at 950 °C for 3 h. The XRD of the as?deposited and annealed films confirmed the formation of Nb3Sn after the annealing. The dissertation discusses the fabrication process, characterized results of the fabricated films, the design of the cylindrical sputter coater and the preliminary data obtained from the sputter coater.

Sayeed, Md Nizam↗

NOVEL TECHNIQUE OF POWER CONTROL IN MAGNETRON TRANSMITTERS FOR INTENSE ACCELERATORS

A novel concept of a high-power magnetron transmitter allowing dynamic phase and power control at the frequency of locking signal is proposed. The transmitter compensating parasitic phase and amplitude modulations inherent in Superconducting RF (SRF) cavities within closed feedback loops is intended for powering of the intensity-frontier superconducting accelerators. The con- cept uses magnetrons driven by a sufficient resonant (in- jection-locking) signal and fed by the voltage which can be below the threshold of self-excitation. This provides an extended range of power control in a single magnetron at highest efficiency minimizing the cost of RF power unit and the operation cost. Proof-of-principle of the proposed concept demonstrated in pulsed and CW regimes with 2.45 GHz, 1kW magnetrons is discussed here. A conceptual scheme of the high-power transmitter allowing the dynamic wide-band phase and y power controls is presented and discussed.

Kazakevich, G.↗

Phase and Power Control in the RF Magnetron Power Stations of Superconducting Accelerators

Phase and power control methods that satisfy the requirements of superconducting accelerators to magnetron RF sources were considered by a simplified kinetic model of a magnetron driven by a resonant injected signal. The model predicting and explaining stable, low noise operation of the tube below the threshold of self-excitation (the Hatrree voltage in free run mode) at a highest efficiency, a wide range of power control and a wide-band phase control was well verified in experiments demonstrating capabilities of the magnetron transmitters for powering of state of the art superconducting accelerators. Descriptions of the kinetic model, the experimental verification and a conceptual scheme of the highly-efficient magnetron RF transmitter for the accelerators are presented and discussed.

43 PARTICLE ACCELERATORS↗

Numerical simulation of a relativistic magnetron using a fluid electron model

An approach to numerically modeling relativistic magnetrons, in which the electrons are represented with a relativistic fluid, is described. A principal effect in the operation of a magnetron is space-charge-limited (SCL) emission of electrons from the cathode. We have developed an approximate SCL emission boundary condition for the fluid electron model. This boundary condition prescribes the flux of electrons as a function of the normal component of the electric field on the boundary. Here we show the results of a benchmarking activity that applies the fluid SCL boundary condition to the one-dimensional Child–Langmuir diode problem and a canonical two-dimensional diode problem. Simulation results for a two-dimensional A6 magnetron are then presented. Computed bunching of the electron cloud occurs and coincides with significant microwave power generation. Numerical convergence of the solution is considered. Sharp gradients in the solution quantities at the diocotron resonance, spanning an interval of three to four grid cells in the most well-resolved case, are present and likely affect convergence.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Preparation and characterization of RF magnetron sputtered CuO/CaTi{sub 4}O{sub 9} thin films with enhanced third-order nonlinear optical properties

The titanate, is a material of interest for various energy applications, including photovoltaics, catalysts, and high-rate energy storage devices. Herein, its related materials, CuO/CaTi{sub 4}O{sub 9} [CCTO] thin films, were successfully fabricated on SrTiO{sub 3} (100) substrates by RF magnetron sputtering assisted with subsequent oxygen annealing. This obtained CCTO thin films were then systemically studied by X-ray powder diffraction (XRD), atomic force microscopy (AFM), scan electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electron microscopy (HRTEM). It was found that CuO and CaTi{sub 4}O{sub 9} (001) particles were closely accumulated together on the surface of the substrate in the annealing process after comparing with that of the as-prepared thin film, which was verified by SEM and AFM results. Furthermore, we investigated the third-order nonlinear optical (NLO) properties of the as-prepared and annealed CCTO thin film by means of the Z-scan technique using 650 nm femtosecond laser pulse. Post-deposition oxygen annealing was found to modify the morphological characteristics of the films, resulting in enhancing their NLO properties. The observation of NLO performance of annealed CCTO thin film indicates that RF magnetron sputtering is a feasible method for the fabrication of optical thin films, which can be expanded to fabricate other NLO materials from the corresponding dispersions. Naturally, we concluded that the CCTO thin film occupy a better NLO property, and thus enlarge its application in nonlinear optics. - Highlights: • The CCTO thin film was prepared using the RF magnetron sputtering and oxygen annealing. • The film was prepared on the SrTiO{sub 3}(100) substrates with a Ca{sub 2}CuO{sub 3} target. • The oxygen annealing was found can effectively enhance the film quality and NLO property. • The film was characterized using XPS, SEM, AFM, TEM, XRD and Z-scan techniques.

36 MATERIALS SCIENCE↗

Structure and properties of ternary manganese nitride Mn{sub 3}CuN{sub y} thin films fabricated by facing target magnetron sputtering

Graphical abstract: This figure reveals the dependence of the texture coefficient TC{sub (111)} and TC{sub (200)} of the Mn{sub 3}CuN{sub y} thin films on T{sub sub}. These results indicate that the preferred orientation of the Mn{sub 3}CuN{sub y} thin films dramatically changed from (1 1 1) to (2 0 0) with the increase of T{sub sub}. In one word, the orientation of Mn{sub 3}CuN{sub y} thin film can be tailored by adjusting the magnetron sputtering processing parameters and substrate. It is the first time to report the deposition of Mn{sub 3}CuN{sub y} thin films on single crystal Si (1 0 0) at various substrate temperatures (T{sub sub}) by facing target magnetron sputtering. The influences of substrate temperature on crystal structure and morphology are discussed. The temperature dependences of magnetization, lattice parameters and resistivity for the resulting film are systematically investigated, which shows several different physical properties from those of previous work. Highlights: {yields} Variation of the substrate temperatures adjusted the preferred orientation from (1 1 1) to (2 0 0) of the Mn{sub 3}CuN{sub y} thin films. {yields} There exists a magnetic ordering transition at 225 K from paramagnetic (PM) to ferrimagnetic (FI), which is different than previous results. {yields} It shows a positive thermal expansion behavior with average linear thermal expansion coefficient 2.49 x 10{sup -5} K{sup -1}. However there was no crystal phase transition occurred around the magnetic transition in the film. {yields} The temperature dependence of resistivity displayed a semiconductor-like behavior, which is quite different from the bulk sample. {yields} We believe that our findings may provide an important role to further utilize the potential of antiperovskite manganese nitride film. -- Abstract: Deposition of Mn{sub 3}CuN{sub y} thin films on single crystal Si (1 0 0) at various substrate temperatures (T{sub sub}) by facing target magnetron sputtering is reported. The crystal structure and composition were characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The results confirmed that the crystalline antiperovskite Mn{sub 3}CuN{sub y} thin film with (2 0 0) highly preferred texture had been obtained at T{sub sub} = 180 {sup o}C. Furthermore, for the resulting Mn{sub 3}CuN{sub y} thin film, it showed different properties compared with the bulk counterpart. There was a paramagnetic to ferrimagnetic transition at 225 K with decreasing temperature. The change of the lattice constant with temperature presented positive thermal expansion behavior and no structural transition was observed. The average linear thermal expansion coefficient ({alpha}) is 2.49 x 10{sup -5} K{sup -1} from 123 K to 298 K. More interestingly, the temperature dependence of resistivity displayed a semiconductor-like behavior, i.e. an obvious monotonous decrease of resistivity with increasing temperature.

36 MATERIALS SCIENCE↗

Impact of magnetron configuration on plasma and film properties of sputtered aluminum nitride thin films

We have investigated the growth of the c-axis oriented aluminum nitride (AlN) thin films on (100) silicon by reactive dc magnetron sputtering at low temperature, considering the effect of the magnet configuration on plasma and film properties. It appears that a magnet modification can significantly modify both the plasma characteristics and the film properties. Electrical and optical characterizations of the plasma phase highlight that depending on the magnet configuration, two very different types of deposition process can be involved in the same deposition chamber. On the one hand, with a balanced magnetron (type 1), the deposition process enhances the production of AlN dimers in the plasma phase and enables to synthesize AlN films with different preferential orientations (100, 002, and even 101). On the other hand, a strongly unbalanced magnetron (type 2) provides a limited production of AlN species in the plasma phase and a strong increase in the ratio of ions to metal atom flux on the growing films. In the latter case, the ion energy provided by the ion flux to the growing film is typically in the 20-30 eV range. Thus, dense (002) oriented films with high crystalline quality are obtained without any substrate heating.

36 MATERIALS SCIENCE↗

Plasma 'anti-assistance' and 'self-assistance' to high power impulse magnetron sputtering

A plasma assistance system was investigated with the goal to operate high power impulse magnetron sputtering (HiPIMS) at lower pressure than usual, thereby to enhance the utilization of the ballistic atoms and ions with high kinetic energy in the film growth process. Gas plasma flow from a constricted plasma source was aimed at the magnetron target. Contrary to initial expectations, such plasma assistance turned out to be contraproductive because it led to the extinction of the magnetron discharge. The effect can be explained by gas rarefaction. A better method of reducing the necessary gas pressure is operation at relatively high pulse repetition rates where the afterglow plasma of one pulse assists in the development of the next pulse. Here we show that this method, known from medium-frequency (MF) pulsed sputtering, is also very important at the much lower pulse repetition rates of HiPIMS. A minimum in the possible operational pressure is found in the frequency region between HiPIMS and MF pulsed sputtering.

36 MATERIALS SCIENCE↗

S-band relativistic magnetron operation with an active plasma cathode

Results of experimental research on a relativistic S-band magnetron with a ferroelectric plasma source as a cathode are presented. The cathode plasma was generated using a driving pulse (approx3 kV, 200 ns) applied to the ferroelectric cathode electrodes via inductive decoupling prior to the beginning of an accelerating pulse (200 kV, 150 ns) delivered by a linear induction accelerator. The magnetron and generated microwave radiation parameters obtained for the ferroelectric plasma cathode and the explosive emission plasma were compared. It was shown that the application of the ferroelectric plasma cathode allows one to avoid a time delay in the appearance of the electron emission to achieve a better matching between the magnetron and linear induction accelerator impedances and to increase significantly (approx30%) the duration of the microwave pulse with an approx10% increase in the microwave power. The latter results in the microwave radiation generation being 30% more efficient than when the explosive emission cathode is used, where efficiency does not exceed 20%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ion Source of Pure Single Charged Boron Based on Planar Magnetron Discharge in Self-Sputtering Mode

A planar magnetron sputtering device with thermally isolated sintered boron target has been designed and demonstrated. The magnetron is intended to use for generation of boron ion beams, as well as in plasma immersion implantation. For a boron target, high target temperature is required because boron has low electrical conductivity at room temperature, which increases with temperature. The target is well insulated thermally and can be heated by an initial low-current, high-voltage DC discharge mode. A discharge power of 16 W was adequate to reach the required surface temperature, after that a transition of the discharge to a high-current, low-voltage mode is observed. Applying high current pulses over the DC heating discharge results in a self-sputtering operational mode of the magnetron discharge. Ion beam was extracted from the discharge plasma. Beam analysis was performed with a time-of-flight system. All the boron ions are single charged. The maximum boron ion fraction in the beam is greater than 99%, and the mean boron ion fraction, time-integrated over the whole pulse length, is about 95%. This kind of boron ion source could be competitive to conventional boron ion sources that utilize compounds such as BF{sub 3}, and could be useful for semiconductor industry application.

36 MATERIALS SCIENCE↗