Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Li batteries”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Dataset of mechanically induced thermal runaway measurement and severity level on Li-ion batteries

The deployment of Li-ion batteries covers a wide range of energy storage applications, from mobile phones, e-bikes, electric vehicles (EV) and stationary energy storage systems. However, safety issue such as thermal runaway is always one of the most important concerns to prevent Li-ion batteries from further market penetration. A standardized single-side indentation test protocol was developed to mechanically induce an internal short-circuit. The cell voltage, compressive load, indenter stroke, and temperature at the indentation point are measured in time series. The test data of each cell, along with cell parameters such as dimensions, mass, chemistry, state of charge (SOC), capacity, are integrated together to calculate a thermal runaway severity score from 0 to100. Complete data collection process including the original measured record, test method, severity score calculation scheme is presented in this article. The thermal runaway severity analysis and the more than 100 tested Li-ion battery records provide a good data source for further comparison and ranking of thermal runaway risks.

25 ENERGY STORAGE↗
DOE OSTI2021

Direct Cathode Recycling of End-Of-Life Li-Ion Batteries Enabled by Redox Mediation

The ongoing surge of electric vehicle (EV) adoption forecasts an unprecedented amount of lithium-ion battery wastes in the near future. Since cathode materials have the highest economic and engineering values, it is essential to recycle and reuse the end-of-life (EOL) cathode materials. Here, we show that redox mediators can deliver lithium ions and electrons from a lithium source to the cathode, efficiently relithiate the EOL cathode materials, and make them ready for new battery production after a postheat treatment. We have found that some quinone-based redox mediators, especially 3,5-di-tert-butyl-o-benzoquinone (DTBQ), can shuttle the charges very fast between Li metal and EOL cathode. Reduction of DTBQ on lithium is evidenced by chemical changes of Li metal and DTBQ, and successful relithiation of the EOL cathode by the subsequent oxidation of DTBQ is verified by electrochemical and structural evaluations.

battery recycling↗
DOE OSTI2020

Pursuing graphite-based K-ion O 2 batteries: a lesson from Li-ion batteries

The replacement of lithium metal by lithium intercalated graphite was crucial for developing safe lithium-ion batteries. Superoxide-based potassium–oxygen batteries represent an exciting metal–oxygen battery with the highest energy efficiencies. However, using potassium metal is a more serious safety threat than lithium. Herein, we explore the possibility of graphite-intercalation anodes for potassium-ion oxygen batteries (PIOBs) with enhanced safety. This work demonstrates for the first time that establishing an artificial potassium salt-rich solid electrolyte interphase (SEI) enables a reversible graphite-intercalation anode (249.6 mA h g -1 after 600 cycles) in a potassium bis(trifluoromethanesulfonyl)imide (KTFSI)-based localized high-concentration electrolyte. Such an electrolyte is stable with the superoxide cathode. The PIOB delivers energy efficiencies above 90% at a depth of discharge (DOD) of 25% for 80 cycles. A three-electrode measurement shows that its overpotential mainly comes from the anode. The lifespan is limited to the gradual degradation of the artificial SEI caused by oxygen crossover. This work represents a step towards achieving holistic anode–electrolyte–cathode compatibility in a PIOB and its realistic evaluation under a controlled DOD.

25 ENERGY STORAGE↗
NASA NTRS2006

Battery Control Boards for Li-Ion Batteries on Mars Exploration Rovers

Rechargeable Lithium-ion batteries have been operating successfully on both Spirit and Opportunity rovers for the last two years, which includes six months of Assembly Launch and Test Operations (ATLO), seven months of cruise and about eleven months of surface operations. The Battery Control Boards designed and fabricated in-house would protect cells against overcharge and over-discharge and provide cell balance. Their performance has thus far been quite satisfactory. The ground data o the mission simulation battery project little capacity loss of less than 3% during cruise and 180 sols. Batteries are poised to extend the mission beyond six months, if not a couple of years.

Ewell, R.↗
DOE OSTI2025

Neutron-Friendly Li-Ion Battery Coin Cell for In Situ 3D Visualization of Li Plating

Advanced battery characterization using in situ/operando neutron imaging is critical for uncovering degradation modes such as lithium (Li) plating in Li-ion batteries (LIBs). However, conventional LIBs hinder operando neutron radiography (NR) and in situ neutron micro-computed tomography (N-μCT) for visualizing Li plating near the graphite-separator interface due to strong attenuation from hydrogen-rich components like PP–PE–PP separators, electrolyte, and Fe-based spacers. In this work, we designed and tested a neutron-friendly battery (NFB) optimized for in situ Li detection during extreme fast charging (XFC). Guided by neutron attenuation cross-sections and material transmission, the NFB enables clear visualization at the graphite–separator interface, which is typically opaque in standard LIBs. Electrochemical tests show the NFB exhibits voltage/current responses like standard cells for up to 50 XFC cycles. However, its lower reversibility and capacity are likely due to Cu-coated Al spacer degradation from delamination or corrosion. We propose titanium spacers as a more stable alternative, albeit requiring custom machining. Using this optimized cell, we achieved simultaneous neutron tomography of multiple cells, capturing in situ 3D images of dead Li accumulation, particularly near graphite edges. These heterogeneous deposits and disconnected Li clusters suggest localized current density hotspots during XFC.

25 ENERGY STORAGE↗
DOE OSTI2022

Rigid-Rod Sulfonated Polyamide as an Aqueous-Processable Binder for Li-Ion Battery Electrodes

Polymer binders are important components of most battery electrodes, ensuring high performance and long-term durability. Increasing demand for lithium-ion batteries in the automotive, stationary power, and portable electronics industries calls for a greener binder to replace poly(vinylidene difluoride) (PVDF). We evaluate the performance of aqueous solution-processed electrodes prepared with a rigid-rod polymer binder, poly(2,2'-disulfonyl-4,4'-benzidine terephthalamide) (PBDT). The polyamide backbone and double-helical configuration of PBDT give rise to its mechanical strength and rigidity, and its functional nature (H-bonding amides and sulfonates) can provide specific binding with electrode particles. LiFePO 4 electrodes prepared with 3 wt% PBDT show mechanical integrity and cycling stability, achieving over 1000 cycles at 4C rate with negligible capacity decay. These electrodes demonstrate comparable rate performance with their PVDF counterparts while eliminating fluorine from the electrode as well as the organic solvents needed for processing. Furthermore, this study reveals that PBDT holds great potential as a binder for advanced sustainable batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Ionic conductive polymers as artificial solid electrolyte interphase films in Li metal batteries – A review

Lithium (Li) metal has been considered as the ultimate anode material for next-generation rechargeable batteries due to its ultra-high theoretical specific capacity (3860 mAh g -1 ) and the lowest reduction voltage (-3.04 V vs the standard hydrogen electrode). However, the dendritic Li formation, uncontrolled interfacial reactions, and huge volume variations lead to unstable solid electrolyte interphase (SEI) layer, low Coulombic efficiency and hence short cycling lifetime. Designing artificial solid electrolyte interphase (artificial SEI) films on the Li metal electrode exhibits great potential to solve the aforementioned problems and enable Li–metal batteries with prolonged lifetime. Polymer materials with good ionic conductivity, superior processability and high flexibility are considered as ideal artificial SEI film materials. In this review, according to the ionic conductive groups, recent advances in polymeric artificial SEI films are summarized to afford a deep understanding of Li ion plating/stripping behavior and present design principles of high-performance artificial SEI films in achieving stable Li metal electrodes. Perspectives regarding to the future research directions of polymeric artificial SEI films for Li–metal electrode are also discussed. The insights and design principles of polymeric artificial SEI films gained in the current review will be definitely useful in achieving the Li–metal batteries with improved energy density, high safety and long cycling lifetime toward next-generation energy storage devices.

25 ENERGY STORAGE↗
NASA NTRS2018

Transition Metal Oxides as Cathodes in Li-O2 battery: A First Principles Investigation

Li-O2 batteries have traditionally used carbon based electrodes (graphite, buckypaper) as the cathode of choice due to its good electrical conductivity, stability against non-aqueous electrolytes like Dimethyl ether (DME) and ease of handling. But, the carbon cathode also leads to formation of carbonate by-products that increase overpotentials during charging leading to degradation of cathode and reduction of cyclability. In this work, we investigate some of the well-known oxides as cathodes with focus on the interface between the oxide surfaces and the discharge product: Li2O2, in the Li-O2 battery using first principles computations. Our results show that attention must be paid on choosing the appropriate surface of the oxides. We extend the analysis to suggest other possible oxide chemistries that should be investigated as cathodes in Li-O2 batteries.

Li-O2 battery↗
NASA NTRS2019

Novel Electrolytes for Use in Li-Air Batteries for NASA Electric Aircraft

Li-Air batteries are a unique fit for electric aircraft due to their high theoretical energy densities and their potential to leverage on-board oxygen systems. The electrolyte and cathode are the limiting factors for advancing this technology. We are investigating novel "electrolyte and cathode engineering" concepts to enable Li-Air batteries with high practical energy densities, rechargeability and safety. New stable electrolytes and cathodes are being designed and fabricated for Li-Air batteries. An array of various electrolytes were screened and analyzed using NMR and DEMS analysis techniques to understand the fundamental decomposition mechanisms at the cathode surface and within the porous polymer separator. (NMR) spectroscopy has yielded mechanistic insight into decomposition pathway, which is vital to the development of future stable electrolyte candidates. Thus far, five new electrolytes have been screened with 2 showing promising results.

Li-Air↗
DOE OSTI2020

Supercooled liquid sulfur maintained in three-dimensional current collector for high-performance Li-S batteries

In lithium-sulfur (Li-S) chemistry, the electrically/ionically insulating nature of sulfur and Li 2 S leads to sluggish electron/ion transfer kinetics for sulfur species conversion. Sulfur and Li 2 S are recognized as solid at room temperature, and solid-liquid phase transitions are the limiting steps in Li-S batteries. Here, we visualize the distinct sulfur growth behaviors on Al, carbon, Ni current collectors and demonstrate that (i) liquid sulfur generated on Ni provides higher reversible capacity, faster kinetics, and better cycling life compared to solid sulfur; and (ii) Ni facilitates the phase transition (e.g., Li 2 S decomposition). Accordingly, light-weight, 3D Ni-based current collector is designed to control the deposition and catalytic conversion of sulfur species toward high-performance Li-S batteries. This work provides insights on the critical role of the current collector in determining the physical state of sulfur and elucidates the correlation between sulfur state and battery performance, which will advance electrode designs in high-energy Li-S batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Pathways for Sustainable Reaction Kinetics in Li-CO2 Batteries

Lithium-carbon dioxide (Li-CO2) batteries hold great promise for high-energy-density storage applications. However, advancing this technology as a sustainable alternative to Li-ion systems requires a deeper understanding of the underlying reaction mechanisms, which remain elusive. A key challenge stems from the added complexity introduced by the presence of oxygen (O2) in CO2 environment. In this study, we employed a stable Cu3(VBi)0.5Se4 mid-entropy catalyst and conducted a comprehensive investigation to uncover the underlying reaction mechanisms in Li-CO2 batteries under varying CO2/O2 ratios. Under pure CO2 conditions, the battery exhibits excellent rechargeability, sustaining up to 1200 cycles. However, at high current densities, the discharge potential drops significantly (below 2.0 V), primarily due to sluggish reaction kinetics caused by solid carbon formation. Interestingly, introducing O2 mitigates this limitation, leading to a 58% increase of the discharge potential (from 1.7 V to 2.7 V) at the high current density of 0.8 mA/cm2, signifying a substantial boost in energy output. Our results reveal that the reactions follow distinct pathways, shifting from surface- to solution-based mechanism, and may even exhibit coexistence of both mechanisms, depending on the CO2/O2 ratio. These findings offer new insights for designing high-performance and sustainable Li-gas batteries utilizing CO2 and O2 mixtures.

Ngo, Anh [University of illinois Chicago]↗
DOE OSTI2025

Operando FTIR investigation of salt dynamics in Li-ion batteries during fast charging

Li-ion batteries, when charged at fast-charging rates ($>$2C), suffer from reduced lifetimes and can undergo catastrophic failure. During high-rate charging, Li-ions are unable to rapidly transport through high-loading electrodes ($>$4 mAh cm −2 ). This results in unequal charge distributions, potentials, and utilization of the active material, which can lead to Li plating. Li-ion concentration polarization, in which Li-ions deplete in the anode and accumulate in the cathode during charging, precedes Li plating. An operando FTIR-ATR graphite/NMC cell developed in this research captured Li-ion concentration polarization in real-time. During fast charging, decreases in Li-ion concentration ($>$95%) were measured at the back of the anode. This is the first verification of complete Li-ion depletion within the anode at high C-rates. The measurements also showed graphite stage transition. A P2D model was developed for comparison to the operando measurements. The measurements agreed with the model in some cases, but disparities existed at high C-rates and loadings. In the experiment, the Li-ion concentration often failed to recover to 1.2 M until several hours after charging, whereas the model Li-ion concentration rapidly recovered. The contrast between the model and experiment results indicates that further investigation is required to improve understanding of Li-ion concentration dynamics during fast charging.

25 - ENERGY STORAGE↗
DOE OSTI2024

Healable and conductive sulfur iodide for solid-state Li–S batteries

Solid-state Li-S batteries (SSLSBs) are made of low-cost and abundant materials free of supply chain concerns. Owing to their high theoretical energy densities, they are highly desirable for electric vehicles. However, the development of SSLSBs has been historically plagued by the insulating nature of sulfur and the poor interfacial contacts induced by its large volume change during cycling, impeding charge transfer among different solid components. We report an S 9.3 I molecular crystal with I 2 inserted in the crystalline sulfur structure, which shows a semiconductor-level electrical conductivity (approximately 5.9 × 10 -7 S cm -1 ) at 25 °C; an 11-order-of-magnitude increase over sulfur itself. Iodine introduces new states into the band gap of sulfur and promotes the formation of reactive polysulfides during electrochemical cycling. Further, the material features a low melting point of around 65 °C, which enables repairing of damaged interfaces due to cycling by periodical remelting of the cathode material. As a result, an Li-S 9.3 I battery demonstrates 400 stable cycles with a specific capacity retention of 87%. The design of this conductive, low-melting-point sulfur iodide material represents a substantial advancement in the chemistry of sulfur materials, and opens the door to the practical realization of SSLSBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Solid 3D Li–S Battery Design via Stacking 2D Conductive Microporous Coordination Polymers and Amorphous Li–S Layers

To make a lithium-sulfur (Li-S) battery practical, not only high gravimetric energy capacity is important, but also high volumetric energy capacity will be required. The currently explored Li-S cathode designs often deploy systems with liquid electrolyte infiltration, hence with relatively low volumetric capacity. In the current study, we theoretically test a compact solid three-dimensional (3D) design (more like a Li-ion battery cathode than a conventional Li-S cathode) consisted of a sandwich structure alternating between the two-dimensional (2D) Mn-hexaaminobenzene-based coordination polymer (2D Mn-HAB-CP) layer and the amorphous Li-S layer. We study the theoretical limits for both its gravimetric and volumetric energy capacity, as well as its structural stability and Li diffusion within the cathode system. To study the Li diffusion within an amorphous system, we also develop a pull-atom molecular dynamics (PA-MD) to calculate the barrier heights of such disordered systems. We reveal the mechanism that determines the Li diffusion in the amorphous layer of the system. Overall, we find such a 3D solid Li-S cathode can be practical, with sufficient large gravimetric and volumetric energy capacity, as well as the Li diffusion constant. It also solves many other common Li-S cathode problems, from Li polysulfide dissolution to electrical insulating, and structure instabilities.

25 ENERGY STORAGE↗