Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Interfacial adhesion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Wear and interfacial transport of material

The paper is a review of adhesion or bonding across an interface between two solids in contact, transfer or transport to one or both surfaces, wear with tangential motion, and the effect of surface films on adhesion, transfer, and wear. The discussion is limited to the case of adhesive wear which deals with the interfacial transport of material from one surface to another. The data presented suggest that the resulting interfacial adhesive bond for metals in contact is generally stronger than the cohesive bond in the cohesively weaker of the two materials so that upon separation of the surfaces transfer will occur from the cohesively weaker material to the cohesively stronger; that with tangential motion of two metal surfaces in contact such as encountered with sliding, rolling, or rubbing contact, the frictional energy can be dissipated in a number of ways, where heating of the surfaces can produce metallurgical changes such as alloying; and that the presence of adsorbed and reacted films on the surface of metals and alloys even in frictions of a monolayer can reduce interfacial bonding, adhesion, and transfer.

Buckley, D. H.↗
NASA NTRS1989

Fundamentals of tribology at the atomic level

Tribology, the science and engineering of solid surfaces in moving contact, is a field that encompasses many disciplines: solid state physics, chemistry, materials science, and mechanical engineering. In spite of the practical importance and maturity of the field, the fundamental understanding of basic phenomena has only recently been attacked. An attempt to define some of these problems and indicate some profitable directions for future research is presented. There are three broad classifications: (1) fluid properties (compression, rheology, additives and particulates); (2) material properties of the solids (deformation, defect formation and energy loss mechanisms); and (3) interfacial properties (adhesion, friction chemical reactions, and boundary films). Research in the categories has traditionally been approached by considering macroscopic material properties. Recent activity has shown that some issues can be approached at the atomic level: the atoms in the materials can be manipulated both experimentally and theoretically, and can produce results related to macroscopic phenomena.

Ferrante, John↗
DOE OSTI2024

Equivalent Properties of Interfacial Void Defects at the CFRTP-adhesive Interface and Their Detrimental Effects on the Bonding Performance of Metal-CFRTP Dissimilar Joints

This paper revealed the detrimental effects of micro-scale air interfacial voids on the debonding at the interface of carbon-fiber-reinforced polyphthalamide (CFRPPA) and thermoset adhesive, representing a weak adherend-adhesive interface, within a dissimilar joint made of an aluminum alloy and a CFRPPA. The reduced lap shear strength of the joint, due to different void area fractions at the CFRPPA-adhesive interface, can be computationally described by using equivalent interfacial properties in the modeling to avoid the explicit modeling of the micro-scale interfacial voids. Such equivalent interfacial properties (e.g., interfacial normal strength, etc.) was found to have a non-linear relationship with respect to interfacial void area fraction as well as lap shear strength. This work has practical applications by utilizing equivalent interfacial properties for the analytical and/or computational design(s) of adhesively bonded joints.

Qiao, Yao↗
NASA NTRS1988

Adhesion, friction and micromechanical properties of ceramics

The adhesion, friction, and micromechanical properties of ceramics, both in monolithic and coating form, are reviewed. Ceramics are examined in contact with themselves, other harder materials, and metals. For the simplicity of discussion, the tribological properties of concern in the processes are separated into two parts. The first part discusses the pull-off force (adhesion) and the shear force required to break the interfacial junctions between contacting surfaces. The role of chemical bonding in adhesion and friction, and the effects of surface contaminant films and temperature on tribological response with respect to adhesion and friction are discussed. The second part deals with abrasion of ceramics. Elastic, plastic, and fracture behavior of ceramics in solid state contact is discussed. The scratch technique of determining the critical load needed to fracture interfacial adhesive bonds of ceramic deposited on substrates is also addressed.

Miyoshi, Kazuhisa↗
NASA NTRS1988

Adhesion, friction and micromechanical properties of ceramics

The adhesion, friction, and micromechanical properties of ceramics, both in monolithic and coating form, are reviewed. Ceramics are examined in contact with themselves, other harder materials, and metals. For the simplicity of discussion, the tribological properties of concern in the processes are separated into two parts. The first part discusses the pull-off force (adhesion) and the shear force required to break the interfacial junctions between contacting surfaces. The role of chemical bonding in adhesion and friction, and the effects of surface contaminant films and temperature on tribological response with respect to adhesion and friction are discussed. The second part deals with abrasion of ceramics. Elastic, plastic, and fracture behavior of ceramics in solid state contact is discussed. The scratch technique of determining the critical load needed to fracture interfacial adhesive bonds of ceramic deposited on substrates is also addressed.

Miyoshi, Kazuhisa↗
DOE OSTI2024

Exploring Failure of Adhesively-Bonded Joints with Different Void Sizes at the Same Void Volume Fraction through A Micro-scale Numerical Modeling

This paper studied the effects of void sizes on the failure behavior of adhesively-bonded materials under global shear via micro-scale computational modeling. The numerical results indicate that large void sizes with increased distances between them at the same void volume fraction can alleviate the reduced joint strength of a weaker adherend-adhesive interface caused by interfacial voids. However, this is not the case for an adherend-adhesive interface with the interfacial tensile strength being sufficiently higher than the adhesive strength, showing the negligible effect on the joint strength due to various void sizes and the amount of interfacial voids. This preliminary investigation provides insightful information for scaling up the void size in the macro-scale computational modeling of joints, and enhances the understanding of the micro-mechanical adhesion in adherend-adhesive interfaces with different levels of bonding.

Qiao, Yao↗
NASA NTRS1989

Fundamental tribological properties of ion-beam-deposited boron nitride films

The adhesion, friction, and micromechanical properties of ion-beam-deposited boron nitride (BN) films are reviewed. The BN films are examined in contact with BN metals and other harder materials. For simplicity of discussion, the tribological properties of concern in the processes are separated into two parts. First, the pull-off force (adhesion) and the shear force required to break the interfacial junctions between contacting surfaces are discussed. The effects of surface films, hardness of metals, and temperature on tribological response with respect to adhesion and friction are considered. The second part deals with the abrasion of the BN films. Elastic, plastic, and fracture behavior of the BN films in solid-state contact are discussed. The scratch technique of determining the critical load needed to fracture interfacial adhesive bonds of BN films deposited on substrates is also addressed.

Miyoshi, Kazuhisa↗
NASA NTRS1990

Fundamental tribological properties of ion-beam-deposited boron nitride films

The adhesion, friction, and micromechanical properties of ion-beam-deposited boron nitride (BN) films are reviewed. The BN films are examined in contact with BN metals and other harder materials. For simplicity of discussion, the tribological properties of concern in the processes are separated into two parts. First, the pull-off force (adhesion) and the shear force required to break the interfacial junctions between contacting surfaces are discussed. The effects of surface films, hardness of metals, and temperature on tribological response with respect to adhesion and friction are considered. The second part deals with the abrasion of the BN films. Elastic, plastic, and fracture behavior of the BN films in solid-state contact are discussed. The scratch technique of determining the critical load needed to fracture interfacial adhesive bonds of BN films deposited on substrates is also addressed.

Miyoshi, K.↗
NASA NTRS2021

An Investigation of the Grain Size and Adhesion Strength of High-Speed Impact Ice

Ice accumulation on aircraft from supercooled water droplets (impact icing) can increase drag and decrease lift, leading to a decrease in fuel efficiency and a potential for unsafe situations. Anti-icing materials and coatings are of high interest to prevent aircraft icing. Because no anti-icing material suitable for in-flight situations has been realized, icing models aim to predict the accumulation and shape of the ice to understand its effects. In both cases, understanding the physical mechanism behind ice adhesion and shedding is necessary. A recent literature review has shown that the apparent ice adhesion strength to any specific material varies over several orders of magnitude across studies and test methods. One of the reasons for this high variance is likely to be the varying microstructure of the ice used for different studies. Although the microstructure of impact ice has been studied in the past, those conditions were not relevant to that of in-flight aircraft icing. The microstructure of the ice formed will determine both its bulk and surface properties, yet it has been overlooked in the ice adhesion community. Here, we use optical microscopy to study the non-uniform ice crystal grain size in impact ice accreted in NASA Glenn Research Center’s Icing Research Tunnel at various icing conditions. Similar to other environmental conditions studied in the literature, we show an increase in grain size at larger distances from the growth interface; however, the data shows substantially larger grains than what was expected from the prior literature. Ice accrued at lower temperatures has a smaller grain size at all distances from the growth interface. No change in grain size was noticed when varying only the wind speed. A correlational analysis shows that smaller grain sizes at the growth interface corresponded to an increase in the apparent ice adhesion strength when the adhesive failure was interfacial, but not when the failure was cohesive. These results may explain the overall trend in the literature of increasing apparent adhesion strength with decreasing temperature. Incorporating microstructure trends for various environmental conditions in icing models may increase the certainty in predicting ice adhesion strength and shedding, and will provide a better basis for comparison between adhesive tests on ice produced in different facilities and at different storage times.

• Ice Fabric↗
NASA NTRS1981

Improved adhesion of Ni films on X-ray damaged polytetrafluoroethylene

The considered investigation shows that the adhesion of evaporated Ni on polytetrafluoroethylene (PTFE) is enhanced by irradiating the PTFE surface prior to evaporation. Evidence obtained with the aid of X-ray photoelectron spectroscopy is presented concerning the association of the enhanced adhesion with an interfacial chemical reaction. Evaporated Ni clearly adheres better to the X-ray damaged PTFE surface than to the undamaged surface. There is evidence that the improved adhesion is not related to the Ni-C bond, but rather to the NiF2. A possible mechanism which may be consistent with the data is the formation of a F-Ni-C complex, where C is a member of the polymer chain.

Wheeler, D. R.↗
NASA NTRS2008

Moisture-Induced Delayed Spallation and Interfacial Hydrogen Embrittlement of Alumina Scales

While interfacial sulfur is the primary chemical factor affecting Al2O3 scale adhesion, moisture-induced delayed spallation appears as a secondary, but impressive, mechanistic detail. Similarities with bulk metallic phenomena suggest that hydrogen embrittlement from ambient humidity, resulting from the reaction Al(sub alloy)+3(H2O)(sub air) = Al(OH)(-) (sub 3) +3H(+) may be the operative mechanism. This proposal was tested on pre-oxidized Rene N5 by standard cathodic hydrogen charging in 1N H2SO4, as monitored by weight change, induced current, and microstructure. Cathodic polarization at -2.0 V abruptly stripped mature Al2O3 scales at the oxide-metal interface. Anodic polarization at +2.0 V, however, produced alloy dissolution. Finally, with no applied voltage, the acid electrolyte produced neither scale spallation nor alloy dissolution. Thus, hydrogen charging was detrimental to alumina scale adhesion. Moisture-induced interfacial hydrogen embrittlement is concluded to be the cause of delayed scale spallation and desktop thermal barrier coating failures.

Smialek, James L.↗
NASA NTRS2010

Ultrasonic Characterization of Interfaces in Composite Bonds

The inverse determination of imperfect interfaces from reflection spectra of normal and oblique incident ultrasonic waves in adhesive bonds of multidirectional composites is investigated. The oblique measurements are complicated by the highly dispersed nature of oblique wave spectra at frequencies above 3MHz. Different strategies for bond property reconstruction, including a modulation method, are discussed. The relation of measured interfacial spring density to the physico-chemical model of a composite interface described by polymer molecular bonds to emulate loss of molecular strength on an adhesive composite interface is discussed. This potentially relates the interfacial (adhesion) strength (number of bonds at the adhesive substrate interface) to the spring constant (stiffness) area density (flux), which is an ultrasonically measurable parameter.

Wang, N.↗
NASA NTRSDate not supplied

Measurement System Analysis of a Novel Phase-Based Ultrasonic NDE Technique for Bond Strength Measurement

Fiber reinforced polymer parts have shown tremendous benefits in aerospace structural applications, but their qualification and certification for use in safety critical areas are currently hindered by the lack of a capable non-destructive evaluation (NDE) method or technique for the inspection of these adhesively bonded parts. Conventional NDE methods and techniques typically detect gross bond defects in a qualitative (Pass/Fail) manner. These techniques struggle to detect weak or kissing bonds. Also, there are no widely adopted NDE methods or techniques for measuring interfacial bond strength or detecting kissing bonds. Bond strength is currently ensured by process control and semi-destructive testing. Results from recent research from other authors, including but not limited to mechanical testing, have shown an excellent correlation between interfacial stiffness of an adhesively bonded joint and the adhesive bond strength of that joint. In this paper, a measurement system analysis (MSA) of a novel phase-based ultrasonic NDE Technique, developed at NASA Langley Research Center, is presented for bond strength measurement to assess at an increased level the measurement process and identify components of variation in that measurement process.

Ultrasound↗
DOE OSTI2026

High pressure effects on EBC systems in high temperature environments

Environmental barrier coatings (EBCs) are designed to protect SiCfiber/SiCmatrix ceramic matrix composites (CMCs) in turbine engines by mitigating wear in high-temperature water vapor environments. The failure of EBCs is frequently attributed to the accelerated oxidation of the silicon bond coating layer when exposed to high-temperature steam, leading to the formation of a thickened thermally grown oxide (TGO). TGO growth increases interfacial stress, weakens adhesion, and results in coating spallation. Understanding the impact of high-temperature oxidation of EBC systems is essential for developing accurate lifespan models for turbine components, although pressurized oxidation testing is extremely sparse in the open literature. In this work, oxidation tests were performed on rare earth silicate EBCs coated onto SiC substrates under increased pressure conditions. The coated specimens were tested at 1100°C, 1200°C, and 1300°C at both 1 atm and 10 atm total pressure in steam environments. Subsequent characterization focused on the microstructural evolution of the EBC/Si/SiC system. The experimental findings indicated that TGO behavior is dependent on high-pressure conditions, with elevated pressure leading to an increase in oxide scale thickness and modifications in its morphology.

Ardrey, Kristyn [ORNL] (ORCID:0000000184407796)↗
DOE OSTI2026

Structure of Layers Formed by [2-(3,6-Disubstituted-9 H -carbazol-9-yl)ethyl]phosphonic Acids on Metal Oxides

[2-(9 H -Carbazol-9-yl)ethyl]phosphonic acid (2PACz) and its derivatives are being used extensively as hole-transport layers in organic and perovskite solar cells due to their ability to modify electrode work function, surface wettability, and in some cases, to improve active-layer adhesion, while minimizing interfacial energy losses. The orientation and coverage of surface modifiers significantly impact these functional properties; however, the detailed structure and packing in these overlayers are challenging to investigate, leading to a lack of understanding of how this structure and packing influence performance and limiting the ability to rationally design molecular modifiers. Here, we investigate monolayers of 2-(9 H -carbazol-9-yl)ethyl phosphonic acid derivatives (from here on referred to as X-2PACz) on indium tin oxide (ITO) and alpha phase aluminum oxide (α-Al 2 O 3 ) using a combination of X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, and X-ray reflectivity (XRR). By correlating elemental ratios, molecular orientation, and electron density profiles, we directly quantify surface coverage, layer thickness, and molecular tilt across a series of chemically related monolayers. We find that 2PACz and the X-2PACz derivatives form dense monolayers on α-Al 2 O 3 and ITO, with similar surface coverages on either substrate that are inversely proportional to molecular steric bulk. These surface coverage results indicate that X-2PACz is sterically limited in its monolayer surface packing density, as opposed to site limited. Despite surface packing density differences between molecules, the NEXAFS data show a constant average molecular orientation of 61° to 65° between the plane of the carbazole and the substrate for all the molecules on both substrates. These results increase our general understanding of 2PACz derivatives as they become increasingly useful in high performance solar cells.

NEXAFS↗
NASA NTRS1974

Effect of Various Material Properties on the Adhesive Stage of Fretting

Various properties of metals and alloys were studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films were found to influence adhesion. High atomic density, low surface energy grain orientations exhibited lower adhesion than other orientations. Knowledge of interfacial surface binding energies assists in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents accomplishes both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗
NASA NTRS1988

Adhesively bonded joints: Testing, analysis, and design; Proceedings of the International Symposium, Baltimore, MD, Sept. 10-12, 1986

The papers contained in this volume provide an overview of the state of the art of testing, analysis, and design of adhesively bonded joints. The papers are grouped in the following sections: mechanical testing, stress analysis, failure mechanisms, and design and durability. Specific topics discussed include determination and verification of elastic parameters for adhesives; factors influencing elastic stresses in double cantilever beam specimens; special mixed finite elements for interfacial stress analysis of adhesively bonded joints; debonding characteristics of adhesively bonded woven Kevlar composites; and environmental durability of adhesively bonded joints.

Johnson, W. S.↗