Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Interface properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

The effect of weak interface on transverse properties of a ceramic matrix composite

Experimental studies conducted at NASA Lewis on SiC reaction-bonded Si3N4 composite system showed that transverse stiffness and strength were much lower than those predicted from existing analytical models based on good interfacial bonding. It was believed that weakened interfaces were responsible for the decrease in tranverse properties. To support this claim, a two-dimensional FEM analysis was performed for a transverse representative volume element. Specifically, the effect of fiber/matrix displacement compatibility at the interface was studied under both tensile and compressive transverse loadings. Interface debonding was represented using active gap elements connecting the fiber and matrix. The analyses show that the transverse tensile strength and stiffness are best predicted when a debonded interface is assumed for the composite. In fact, the measured properties can be predicted by simply replacing the fibers by voids. Thus, it is found that little or no interfacial bonding exists in the composite, and that an elastic analysis can predict the transverse stiffness and strength.

Shimansky, R. A.↗
DOE OSTI2026

Interface and Thermophysical Properties of R 32 Refrigerant

Driven by the urgent demand for efficient cooling in microelectronics and advanced thermal management systems, difluoromethane (R32/CH 2 F 2 ) has emerged as a promising candidate owing to its favorable thermophysical properties, including high heat transfer efficiency and low viscosity. While bulk properties such as density, viscosity, and thermal conductivity have been widely studied, interfacial properties, including surface tension and interfacial thickness, remain comparatively underexplored, despite their importance in phase-transition dynamics. Here, we perform molecular dynamics (MD) simulations from 180 to 300 K using an optimized transferable force field for fluoropropenes with enhanced electrostatics to assess both bulk and interfacial behavior of R32. Simulations reproduced density within ±2.1%, viscosity within 3.05%, and thermal conductivity within 7.41% of NIST reference data. Heat capacities (C p and C v ) were predicted within 5%. For interfacial properties, surface tension trends were reproduced within 13.58% deviation, and the vapor–liquid coexistence curve closely matched reference data, yielding a critical temperature of 345.7 K (1.6% deviation) and a critical density of 0.397 g/cm 3 (6.4% deviation). Importantly, the vapor–liquid interface exhibited pronounced temperature-dependent broadening across the 180–290 K range. This behavior correlates with increasing molecular kinetic energy, reduction in intermolecular cohesive interactions, and a progressive loss of preferential dipole alignment, which collectively enhance thermal fluctuation amplitudes at elevated temperatures. These validated results provide predictive molecular-level insights, particularly for interfacial properties that remain less characterized. By reducing property prediction errors in key parameters such as critical temperature, this work provides reliable inputs for heat-exchanger and system models. Such correlations can support optimized component sizing, improved performance, and reduced refrigerant charge. Beyond R32, the methodology offers a transferable framework for blended and next-generation low-GWP refrigerants, contributing to sustainable thermal management aligned with the 2027 EU F-Gas regulation and 2030 Kigali Amendment.

Fluids↗
DOE OSTI2021

Interface and optical properties of Zn 1-x Mg x O films with Mg content of more than 70% grown on the (1$\bar{2}$10)-ZnO substrates

Fabricating Zn 1-x MgxO films with a high Mg content is key to their applications in deep-ultraviolet optoelectronic devices. In this work, we report the preparation of Zn1-xMgxO films on ($1\bar{2}10$)-ZnO substrates by molecular beam epitaxy. The Zn 1-x Mg x O/($1\bar{2}10$)-ZnO structure is revealed by x-ray diffraction and high-resolution transmission electron microscopy. Remarkably, no cubic MgO is observed for films with 74.6% Mg content; the film shows mainly the wurtzite structure with some intermediate phases at the interface. Photoluminescence spectra show that the film exhibits good optoelectronic properties with a bandgap of 4.6 eV. This work provides a new avenue for the fabrication of deep-ultraviolet Zn 1-x Mg x O films.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Thermal relaxation of strain and twist in ferroelectric hexagonal boron nitride moiré interfaces

New properties can arise at van der Waals (vdW) interfaces hosting a moiré pattern generated by interlayer twist and strain. However, achieving precise control of interlayer twist/strain remains an ongoing challenge in vdW heterostructure assembly, and even subtle variation in these structural parameters can create significant changes in the moiré period and emergent properties. Characterizing the rate of interlayer twist/strain relaxation during thermal annealing is critical to establish a thermal budget for vdW heterostructure construction and may provide a route to improve the homogeneity of the interface or to control its final state. Here, we characterize the spatial and temporal dependence of interfacial twist and strain relaxation in marginally-twisted hBN/hBN interfaces heated under conditions relevant to vdW heterostructure assembly and typical sample annealing. We find that the ferroelectric hBN/hBN moiré at very small twist angles (θ ≤ 0.1°) relaxes minimally during annealing in air at typical assembly temperatures of 170°C. However, at 400°C, twist angle relaxes significantly, accompanied by a decrease in spatial uniformity. Uniaxial heterostrain initially increases and then decreases over time, becoming increasingly non-uniform in direction. Structural irregularities such as step edges, contamination bubbles, or contact with the underlying substrate result in local inhomogeneity in the rate of relaxation.

2D materials↗
DOE OSTI2022

Tomographic imaging of atmospheric pressure plasma on complex surfaces

Many plasma types and behaviors such as streamer, arcs, cathode spots, anode spots, ionization waves, and magnetic field interactions create non-symmetric, fully 3D plasma structures. The plasma distribution in 3D space is heavily influenced by complex surfaces and the coupling interactions between plasma properties and the interfacing material properties. For example, ionization waves propagate in directions where ionization rates are highest, leading to complex configurations that are not fully understood or well characterized. Recent advances in laser diagnostics and models have been able to investigate well-controlled idealized plasmas in 2D fashion, but the complex structure in actual plasmas requires a technique than can provide a more complete 3D picture. However, 3D plasma diagnostics do not currently exist. To address this limitation, this activity will leverage available equipment to build a new tomographic optical imaging capability and advance the state-of-the-art in plasma diagnostics to investigate 3D phenomena on complex surfaces.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1990

Properties of insulator interfaces with p-HgCdTe

Heat treatment at 70 C of low carrier concentration p-type HgCdTe samples (p sub o = 8 x 10 exp 14/cm) generates an inverted surface layer. A two day anneal process below 95 C did not affect the Hall coefficient, whereas an almost complete recovery was obtained by annealing at 120 C. While bulk electron mobility, obtained from PEM data, remained high (about 9 x 10 exp 4 sq cm/V s at 77 K), surface mobility is lower by more than an order of magnitude. Surface recombination velocity indicates a continuous improvement with increased temperature, and the activation energy remains equal to the vacancies energy level. The proposed mechanism is that of positive changes in the sulfide migrating towards the interface and generating an image inversion layer.

Schacham, Samuel E.↗
NASA NTRS2011

JPL Thermal Design Modeling Philosophy and NASA-STD-7009 Standard for Models and Simulations - A Case Study

The Standard JPL thermal engineering practice prescribes worst-case methodologies for design. In this process, environmental and key uncertain thermal parameters (e.g., thermal blanket performance, interface conductance, optical properties) are stacked in a worst case fashion to yield the most hot- or cold-biased temperature. Thus, these simulations would represent the upper and lower bounds. This, effectively, represents JPL thermal design margin philosophy. Uncertainty in the margins and the absolute temperatures is usually estimated by sensitivity analyses and/or by comparing the worst-case results with "expected" results. Applicability of the analytical model for specific design purposes along with any temperature requirement violations are documented in peer and project design review material. In 2008, NASA released NASA-STD-7009, Standard for Models and Simulations. The scope of this standard covers the development and maintenance of models, the operation of simulations, the analysis of the results, training, recommended practices, the assessment of the Modeling and Simulation (M&S) credibility, and the reporting of the M&S results. The Mars Exploration Rover (MER) project thermal control system M&S activity was chosen as a case study determining whether JPL practice is in line with the standard and to identify areas of non-compliance. This paper summarizes the results and makes recommendations regarding the application of this standard to JPL thermal M&S practices.

thermal blanket performance↗
NASA NTRS1979

Effects of isothermal and cyclic exposures on interface structure and mechanical properties of FPalpha-Al2O3/aluminum composites

The microstructural and interface stability of FPalpha-Al203/Al-Li composites are investigated as a function of isothermal exposure at 500 C or thermal cycling between 140 and 500 C with hold time at Tmax. Interfacial morphology, growth kinetics, crystal structure, and composition of interfacial reaction products are characterized. Strength is monitored in the transverse orientation, and fracture mechanics is analyzed in terms of interface reaction products. The interfacial reaction product in FP/Al is Li2O.5Al2O3. Significant fiber-matrix reaction occurs during fabrication. The number of thermal cycles rather than total time at Tmax is the determining factor in strength degradation, thermal cycling giving rise to voids at the fiber-matrix interface. Extensive interface failures occur at composite fracture stresses below about 128 MPa; above this stress level failure is attributed to ductile matrix fracture.

Kim, W. M.↗
DOE OSTI2026

Performance of Heterostructural TaC/AlGaN Schottky Diodes Based on First Principles Electronic Structure Properties

Advances in ultra-wide bandgap materials, such as high Al-content AlxGa1-xN (AlGaN), are essential for next generation power electronics, but the requirement for lattice matched substrates is currently a significant obstacle. Recently, conductive TaC has emerged as a promising virtual substrate for AlGaN heteroepitaxy, with wurtzite (0001) AlxGa1-xN lattice-matched to rocksalt (111) TaC at x ~ 0.5. Thus, understanding and controlling the electronic properties of the TaC/AlGaN interface is key for developing technological applications based on TaC/AlGaN devices. Using density functional theory and electronic structure calculations, we here investigate TaC/Al0.5Ga0.5N interfaces, where we include explicit alloy models in the slab calculations. We predict the Schottky barrier height and the electric field discontinuity resulting from interface charges. Considering all possible combinations of (Ta, C) substrate termination, (Al/Ga, N) nucleation, and (Al/Ga, N) polarity, we construct a chemical potential phase diagram to identify the stable interfaces that can be accessed through variation of the synthesis conditions. The predicted interface electronic properties are implemented in device performance simulations to demonstrate a practical design for a strain-free, high-efficiency TaC/AlGaN Schottky diode with a low barrier height and without interface charges, underscoring the potential of TaC as a substrate for ultra-wide bandgap devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1982

Interface control and mechanical property improvements in silicon carbide/titanium composites

Several composite systems made of titanium matrix reinforced with silicon carbide fiber were investigated to obtain a better understanding of composite-degradation mechanisms and to develop techniques to minimize loss of mechanical properties during fabrication and in service. Emphasis was on interface control by fiber or matrix coatings. X-ray diffraction studies on planar samples showed that the formation of titanium silicides was greatly inhibited by the presence of aluminum or Ti3A1 layers at the fiber-matrix interface, with the Ti3A1 being more effective in reducing the reactions. Fiber studies showed that coating the fiber with a 1-micron-thick layer of aluminum improved the as-fabricated strength of a stoichiometric SiC fiber and reduced the fiber degradation during exposure to composite-fabrication conditions. Applying an interfacial barrier by coating the matrix foils instead of the fibers was found to be an effective method for improving composite strength. Reducing the fabrication temperature also resulted in significant improvements in composite strengths. Good-quality, well-consolidated composites were fabricated at temperatures well below those currently used for SiC-Ti composite fabrication.

Brewer, W. D.↗
DOE OSTI2022

On the Interfacial Behavior of Catenated Poly(l-lactide) at the Air–Water Interface

Interfacial properties of polymeric materials are significantly influenced by their architectural structures and spatial features, while such a study of topologically interesting macromolecules is rarely reported. Here, we reported, for the first time, the interfacial behavior of catenated poly(l-lactide) (C-PLA) at the air–water interface and compared it with its linear analogue (L-PLA). The isotherms of surface pressure–area per repeating unit showed significant interfacial behavioral differences between the two polymers with different topologies. Isobaric creep experiments and compression–expansion cycles also showed that C-PLA demonstrated higher stability at the air–water interface. Interestingly, when the films at different surface pressures were transferred via the Langmuir–Blodgett method, successive atomic force microscopy imaging displayed distinct nanomorphologies, in which the surface of C-PLA exhibited nanofibrous structures, while that of the L-PLA revealed a smoother topology with less fiber-like structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Impact of the Atomic Structure at the BiVO 4 /TiO 2 Interface on the Electronic Properties and Performance of BiVO 4 /TiO 2 Photoanodes

In photoelectrochemical cells, semiconductor electrodes are usually interfaced with protection layers to extend their stability. Ideally, the protection layer should not decrease photocurrent generation. Hence, the conduction band minimum (CBM) and valence band maximum (VBM) of the protection layer should appropriately align with those of the underlying semiconductor electrode to facilitate the desired interfacial charge transfer with minimal interfacial recombination. However, predicting interfacial band alignment can be challenging, as it may vary depending on the detailed interfacial atomic structure. Investigating the effect of the atomic structure at the semiconductor/protection layer junction on the band alignment is also challenging as it requires samples with varied interfaces without altering the semiconductor and protection layers. Here, we considered TiO 2 , the most widely used material as a protection layer, interfaced with a BiVO 4 photoanode, and we fabricated two n-type BiVO 4 (010)/TiO 2 photoanodes where a thin (∼4 nm) amorphous TiO 2 layer was deposited by atomic layer deposition (ALD). While the individual BiVO 4 (010) and TiO 2 layers were identical in these two samples, we modified the interfacial atomic structure at the BiVO 4 /TiO 2 junction by changing which precursor, Ti or O, was introduced first upon deposition of TiO 2 . By experimentally and computationally investigating the differences in these two samples, we show that the band alignments between BiVO 4 and TiO 2 at the interface may not be straightforwardly predicted by the CBM and VBM of bulk BiVO 4 and TiO 2 and that interfacial atomic arrangements can have a marked impact on the electronic properties and photoelectrochemical performance of the BiVO 4 (010)/TiO 2 photoanode.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Electric Field Effects on Water and Ion Structure and Diffusion at the Orthoclase (001)–Water Interface

Understanding the electrochemical properties of mineral–water interfaces tends to rely upon electrical double layer (EDL) models, but these models are based on the assumption that electrostatic equilibrium is constantly maintained. In reality, interfacial reactions, ion diffusion, and their electrochemical signatures are based in nonequilibrium conditions of locally or globally imbalanced electrical fields where current EDL models have limited purview. In this work, we performed molecular dynamics (MD) simulations of the orthoclase (001) surface in contact with a 1 M NaCl aqueous solution under various electric fields, to explore the interplay between EDL structure and dynamics when perturbed by electric fields of different direction and strength, by confinement, and by different distributions of structural surface charge. The simulations showed that confinement between two opposing (001) surfaces led to the development of an induced field when the applied field was perpendicular to the surfaces and, as a result, to ionic diffusion coefficients that were independent of electric field strength. In contrast, when the applied field was parallel to the surfaces, confinement resulted in ionic diffusion coefficients that were more strongly dependent on the magnitude of the electric field than in bulk water. Differences in the density and distribution of aluminol groups on the two surfaces had a significant impact on how the interfacial structure and dynamics varied in the presence of an electric field. Notably, these differences resulted in an electro-osmotic flow with opposite directions at the two surfaces under parallel applied electric field. Overall, the MD simulations highlighted the importance of considering atomic-level structure and heterogeneities when developing models of the electrochemical properties of mineral–water interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Photoelectrochemical Imaging of Charge Separation between MoS 2 Triangles and Insulating SiO 2 Support

The role of the insulating support in photocatalysis is poorly understood. Using high-resolution photo-scanning electrochemical microscopy (photo-SECM), we observed significant spatial charge separation in few-layer-thick molybdenum disulfide (MoS 2 ) triangles attached to a SiO 2 substrate. Spatially resolved surface photovoltage (SPV) measurements revealed that photogenerated holes migrate from MoS 2 to the SiO 2 surface and travel laterally over distances exceeding 2 μm, driven by the builtin electric field of ~1.7 kV/cm. In thicker and less uniform flakes, the charge separation is dominated by internal driving forces within MoS 2 , without significant contribution from SiO 2 . These findings underscore the importance of insulator–semiconductor interactions for effective charge separation, suggesting a new strategy for optimizing photocatalytic systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗