Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “In situ microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A study on the creep behavior of alloy 709 using in-situ scanning electron microscopy

In this research, an experimental evaluation of creep properties of Alloy 709 in the temperature range of 750–850 °C was undertaken. Alloy 709 is a novel austenitic stainless steel with 20% Cr and 25% Ni by wt% that was developed for application in structural components of nuclear power plants. Creep rupture tests were conducted in an in-situ heating-loading and Scanning Electron Microscope (SEM) unit equipped with Electron Backscatter Diffraction (EBSD) detector and Energy Dispersive Spectroscopy (EDS). “Real-time” creep damage mechanisms of Alloy 709 at various stresses and temperatures using a flat, un-notched sample with continuously reducing cross-section is studied so that the failure and maximum creep damage occurred at the center of the sample where the in-situ SEM imaging could be focused. Accelerated creep tests at temperatures and stresses above service conditions were performed by employing multiple blocks of constant loads where the loads were increased once the sample attained constant creep rate, indicating a secondary creep regime. This technique ensures multiple data points can be obtained from the same test, saves the time required for an otherwise long-term creep test and usage of SEM. Further, Coincident Site Lattice (CSL) boundary maps were collected as control maps before testing, and the grain boundaries were observed during the creep test to understand the effect of grain boundary character on the creep damage mechanism. Void growth, grain boundary separation, and sliding were found to be the main creep mechanisms whose rate is dependent on stress and temperature. Failure mechanisms studied on the fracture surface using SEM fractography were correlated to the sample surface observations to create complementary information to better understand the underline creep mechanism of Alloy 709.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Integrated atomic force microscopy and x-ray irradiation for in situ characterization of radiation-induced processes

Understanding radiation-induced chemical and physical transformations at material interfaces is important across diverse fields, but experimental approaches are often limited to either ex situ observations or in situ electron microscopy or synchrotron-based methods in which cases the radiation type and dose are inextricably tied to the imaging basis itself. In this work we overcome this limitation by demonstrating integration of an X-ray source with an atomic force microscope to directly monitor radiolytically-driven interfacial chemistry at the nanoscale. We illustrate the value of in situ observations by examining effects of radiolysis on material adhesion forces in aqueous solution, as well as examining the production of alkali nitrates at the interface between an alkali halide crystal surface and air. For the examined salt-air interface, direct visualization under flexible experimental conditions greatly extends prior observations by enabling the transformation process to be followed comprehensively from source-to-sink with mass balance quantitation. Overall, our novel rad-AFM opens doors into understanding the dynamics of radiolytically-driven mass transfer and surface alteration at the nanoscale in real-time.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Photo-exfoliation of MoS 2 quantum dots from nanosheets: an in-situ transmission electron microscopy study

Fabrication of transition metal dichalcogenide (TMD) quantum dots (QDs) is complex and requires submerging of powders in binary solvents and the constant tuning of wavelength and pulsed frequency of light to achieve a desired reaction. Here,iInstead of liquid state photoexfoliation, we utilize infrared laser irradiation of free-standing MoS 2 flakes in transmission electron microscope (TEM) to achieve solid-state multi-level photoexfoliation of QDs. By investigating the steps involved in photochemical reaction between the surface of MoS 2 and the laser beam, we gain insight into each step of the photoexfoliation mechanism and observe high yield production of QDs, led by an inhomogeneous crystalline size distribution. Additionally, by using a laser with a lower energy than the indirect optical transition of bulk MoS 2 , we conclude that the underlying phenomena behind the photoexfoliation is from multi-photon absorption achieved at high optical outputs from the laser source. These findings provide an environmentally friendly synthesis method to fabricate QDs for potential applications in biomedicine, optoelectronics, and fluorescence sensing.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mechanistic Transformation of CuI Nanoparticles Into Oxidation‐Resistant 2D Copper Nanoplates

Unconventional phase transformations reveal new crystallization mechanisms, yet direct observation of such pathways during nanoscale solution-phase synthesis remains challenging. This study uncovers an atypical growth process in which thermodynamically stable CuI nanoparticles (NPs) transform into high-energy 2D Cu plates. Using a combination of in situ transmission electron microscopy, ex situ structural analysis, and density functional theory calculations shows that the formation of structural defects induced by hexadecylamine and chloride ions facilitates the transformation by promoting surface iodine vacancies. The resulting Cu{111} nanoplates, with ultrathin thicknesses (≈4 nm) and exceptionally high aspect ratios (≈450), display enhanced oxidation resistance and long-term stability under ambient conditions. This resistance is attributed to the close-packed {111} facets, which suppress chemical oxidation even after extended exposure to air over 100 days. These findings provide new insights into non-classical crystallization pathways in metal nanomaterials and suggest a versatile approach for preparing oxidation-resistant, structurally defined Cu nanostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultrahigh temperature in situ transmission electron microscopy based bicrystal coble creep in Zirconia II: Interfacial thermodynamics and transport mechanisms

This work uses a combination of stress dependent single grain boundary Coble creep and zero-creep experiments to measure interfacial energies, along with grain boundary point defect formation and migration volumes in cubic ZrO 2 . These data, along with interfacial diffusivities measured in a companion paper are then applied to analyzing two-particle sintering. The analysis presented here indicates that the large activation volume, v * = v f + v m primarily derives from a large migration volume and suggests that the grain boundary rate limiting defects are delocalized, possibly due to electrostatic interactions between charge compensating defects. The discrete nature of the sintering and creep process observed in the small-scale experiments supports the hypothesis that grain boundary dislocations serve as sources and sinks for grain boundary point defects and facilitate strain during sintering and Coble creep. Model two-particle sintering experiments demonstrate that initial-stage densification follows interface reaction rate-limited kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Insights into Mechanisms of Screw Feeder Plugging by Heated Pine Forestry Residues Using in-situ and Correlative Microscopy

Increasing concerns about global carbon emissions due to fossil fuel use has created interest in renewable fuel alternatives, such as lignocellulosic biomass. With an estimated global biomass production probability ten-fold higher than projected need, functionalizing and scaling biomass conversion processes, like pyrolysis, is a promising component of a diverse sustainable energy program (Kan, Strezov, & Evans, 2016). Pyrolysis reactors employed in biomass conversion often encounter the known problem of screw feeder plugging, halting work and reducing efficiency of biorefineries. Although the screw feeder is not heated directly, conductive heat transfer from the fluidized bed pyrolysis reactor creates a temperature gradient, where particles experience temperatures between 22°C and 500°C from the time they enter the feeder to being emptied into the reactor (Digman, Joo, & Kim, 2009; Nieminen & Folke, 1982). The impact of unintentional heating on this highly variable feedstock may result in particle morphology modification, surface texture transformation, and the evolution of viscous compounds and may contribute to screw feeder plugging (Haas, Nimlos, & Donohoe, 2009; Ingram et al., 2008). We hypothesized that particles of various anatomical fractions (including needles, branches, bark, cambium, and whitewood) will experience dramatic changes during this heating regime, which will be characterized by decreased particle size, increased surface roughness, degradation of key structural macromolecules, and generation of viscous compounds that would result in increased particle friction and cohesion, contributing to screw feeder plugging.

biofuels↗
DOE OSTI2023

Assessment of the Degradation Mechanisms of Cu Electrodes during the CO 2 Reduction Reaction

Catalyst degradation and product selectivity changes are two of the key challenges in the electrochemical reduction of CO 2 on copper electrodes. Yet, these aspects are often overlooked. Here, we combine in situ X-ray spectroscopy, in situ electron microscopy, and ex situ characterization techniques to follow the long-term evolution of the catalyst morphology, electronic structure, surface composition, activity, and product selectivity of Cu nanosized crystals during the CO 2 reduction reaction. We found no changes in the electronic structure of the electrode under cathodic potentiostatic control over time, nor was there any build-up of contaminants. In contrast, the electrode morphology is modified by prolonged CO 2 electroreduction, which transforms the initially faceted Cu particles into a rough/rounded structure. In conjunction with these morphological changes, the current increases and the selectivity changes from value-added hydrocarbons to less valuable side reaction products, i.e. , hydrogen and CO. Hence, our results suggest that the stabilization of a faceted Cu morphology is pivotal for ensuring optimal long-term performance in the selective reduction of CO 2 into hydrocarbons and oxygenated products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

In Situ Transmission Electron Microscopy: Signal processing challenges and examples

Transmission electron microscopy (TEM) is a powerful tool for imaging material structure and characterizing material chemistry. Recent advances in data collection technology for TEM have enabled high-volume and high-resolution data collection at a microsecond frame rate. Here, taking advantage of these advances in data collection rates requires the development and application of data processing tools, including image analysis, feature extraction, and streaming data processing techniques. In this article, we highlight a few areas in materials science that have benefited from combining signal processing and statistical analysis with data collection capabilities in TEM and present a future outlook on opportunities of integrating signal processing with automated TEM data analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Facet-dependent dispersion and aggregation of aqueous hematite nanoparticles

Nanoparticle aggregates in solution controls surface reactivity and function. Complete dispersion often requires additive sorbents to impart a net repulsive interaction between particles. Facet engineering of nanocrystals offers an alternative approach to produce monodisperse suspensions simply based on facet-specific interaction with solvent molecules. Here, we measure the dispersion/aggregation of three morphologies of hematite (α-Fe 2 O 3 ) nanoparticles in varied aqueous solutions using ex situ electron microscopy and in situ small-angle x-ray scattering. We demonstrate a unique tendency of (104) hematite nanoparticles to maintain a monodisperse state across a wide range of solution conditions not observed with (001)- and (116)-dominated particles. Density functional theory calculations reveal an inert, densely hydrogen-bonded first water layer on the (104) facet that favors interparticle dispersion. Results validate the notion that nanoparticle dispersions can be controlled through morphology for specific solvents, which may help in the development of various nanoparticle applications that rely on their interfacial area to be highly accessible in stable suspensions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The Reactivity and Structural Dynamics of Supported Metal Nanoclusters Using Electron Microscopy, in-situ X-Ray Spectroscopy, Electronic Structure Theories, and Molecular Dynamics Simulations

This research will provide new methods to determine the structures and compositions of heterogeneous catalysts as they exist in reaction conditions. The new tools will make it possible to understand how extremely small material structures—ones in a size range spanning from single atoms to larger polyatomic clusters—make it possible to carry out highly selective chemical transformations required to synthesize useful materials as well as for efficient energy production and utilization. The tools will make it possible to see how the atomic structures of catalytic materials evolve over time under the conditions of their use, and in this way provide understandings to guide the design of new energy-efficient catalysts. The work will make it possible to answer long standing questions that include the following. How does catalyst structure help guide molecules along specific reaction pathways? What are the important intermediates involved in these transformations? How do the structures and reactivity of catalytic materials, as well as the chemistry of their interfaces, vary with reaction conditions? Is it possible to develop new catalytic materials using new knowledge of the active structures and reaction mechanisms? The work will provide heretofore unavailable experimental tools that can be applied in advanced programs of research addressing such questions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗