Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ISOTHERMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Site heterogeneity and broad surface-binding isotherms in modern catalysis: Building intuition beyond the Sabatier principle

Learning the science of heterogeneous catalysis and electrocatalysis always starts with the simple case of a flat, uniform surface with an ideal adsorbate. It has of course been recognized for a century that real catalysts are more complicated. For the increasingly complex catalysts of the 21st century, this Perspective argues that surface heterogeneity and non-ideal binding isotherms are central features, and their implications need to be incorporated in current thinking. A variety of systems are described herein where catalyst complexity leads to broad, non-Langmuirian surface isotherms for the binding of hydrogen atoms – and this occurs even for ideal, flat Pt(111) surfaces. Modern catalysis employs nanoscale materials whose surfaces have substantial step, edge, corner, impurity, and other defect sites, and they increasingly have both metallic and non-metallic elements M n X m , including metal oxides, chalcogenides, pnictides, carbides, doped carbons, etc. The surfaces of such catalysts are often not crystal facets of the bulk phase underneath, and they typically have a variety of potential active sites. Catalytic surfaces in operando are often non-stoichiometric, amorphous, dynamic, and impure, and often vary from one part of the surface to another. Understanding of the issues that arise at such nanoscale, multi-element catalysts is just beginning to emerge. Yet these catalysts are widely discussed using Brønsted/Bell-Evans-Polanyi (BEP) relations, volcano plots, Tafel slopes, the Butler-Volmer equation, and other linear free energy relations (LFERs), which all depend on the implicit assumption that the active sites are “similar” and that surface adsorption is close to ideal. These assumptions underly the ubiquitous intuition based on the Sabatier Principle, that the fastest catalysis will occur when key intermediates have free energies of adsorption that are not too strong nor too weak. Current catalysis research often aims to minimize the complexity of non-ideal isotherms through experimental and computational design (e.g., the use of single crystal surfaces), and these studies are the foundation of the field. In contrast, this Perspective argues that the heterogeneity of binding sites and binding energies is an inherent strength of these catalysts. Here, this diversity makes many nanoscale catalysts inherently a high-throughput screen wrapped in a tiny package. Only by making the heterogeneity part of the foundation of catalysis models, sorting the types of active sites and dissecting non-ideal binding isotherms, will modern catalysis learn to harness the inherent diversity of real catalysts. Controlling and exploiting diversity rather than avoiding it will help to optimize complex modern catalysts and catalytic conditions.

Mayer, James M.↗

The transformation behavior of Cu-8.0Ni-1.8Si-0.6Sn-0.15Mg alloy during isothermal heat treatment

The transformation behavior of Cu-8.0Ni-1.8Si-0.6Sn-0.15Mg alloy during isothermal heat treatment has been studied by transmission electron microscope observation. On the basis of micro-hardness measurement, time-temperature-property curves of the alloy have been established, and nose-temperatures of curves are about 650 deg. C. Discontinuous precipitates appeared as the samples isothermal heat treated at 550 deg. C, while continuous precipitates appeared as the samples isothermal heat treated at temperatures below 550 deg. C and above 650 deg. C. {beta}-Ni{sub 3}Si, {delta}-Ni{sub 2}Si and {delta}'-Ni{sub 2}Si precipitates were observed in the specimens. The crystal orientation relationships between copper matrix and precipitates were determined as (02-bar 2-bar){sub Cu} || (01-bar 1-bar){sub {beta}} || (010){sub {delta}}, [100]{sub Cu} || [100]{sub {beta}} || [001]{sub {delta}};(02-bar 2-bar){sub Cu} || (01-bar 1-bar){sub {beta}} || (100){sub {delta}} ', [100]{sub Cu} || [100]{sub {beta}} || [001]{sub {delta}} '. - Highlights: {yields} TTP curves have been established and their nose-tip temperatures are about 650 deg. C. {yields} Discontinuous precipitation appeared during isothermal treated at 550 deg. C. {yields} Continuous precipitation appeared when temperature is below 550 deg. C and above 650 deg. C. {yields} Crystal orientations relationships are: (02-bar 2-bar){sub Cu} || (01-bar 1-bar){sub {beta}} || (010){sub {delta}}, [100]{sub Cu} || [100]{sub {beta}} || [001]{sub {delta}};(02-bar 2-bar){sub Cu} || (01-bar 1-bar){sub {beta}} || (100){sub {delta}} ', [100]{sub Cu} || [100]{sub {beta}} || [001]{sub {delta}} '.

36 MATERIALS SCIENCE↗

On the evolution of secondary hardening carbides during continuous versus isothermal heat treatment of high speed steel HS 6-5-2

The continuous heat treatment of high speed steels reduces the process times from several hours to a few minutes. The resulting cost savings as well as lower decarburisation and distortion make the continuous heat treatment favourable over an isothermal heat treatment. However, the microstructure-property relationship during continuous heat treatments is far from being well understood. In order to identify the key microstructural features for the future optimisation of continuous heat treatments of high speed steels this study compares a current industrial continuous and an isothermal heat treatment of steel HS 6-5-2 by means of light optical microscopy, scanning electron microscopy, X-ray diffraction, atom probe tomography, and red hardness. After continuous hardening the content of primary carbides is higher and the amount of retained austenite is lower compared to isothermal hardening. Due to the reduced time for dissolution of primary carbides a lower content of alloying elements is present in the martensitic matrix for subsequent tempering. Therefore, the chemical composition of the secondary hardening carbides after tempering is different for a continuous heat treatment. Although the difference in chemistry is quite pronounced, the deterioration of the hardness at elevated temperatures, which strongly influences the performance characteristics of the finished parts, is not altered. - Highlights: •We studied the continuous and isothermal heat treatment of the steel HS 6-5-2. •The amount of primary carbides is higher in a continuously heat treated steel. •The chemistry of secondary hardening carbides changes during tempering. •Continuously heat treated steels exhibit the same performance characteristics.

36 MATERIALS SCIENCE↗

Non-isothermal creep aging behaviors of an Al-Zn-Mg-Cu alloy

Highlights: • A novel non-isothermal creep aging (NICA) process is proposed to improve sheet metal forming efficiency. • Appropriate heating-cooling rate is conducive to obtain desired creep deformation and material properties. • The time consumption in optimized NICA process is about half of that in conventional creep aging process. • In NICA, the precipitates formed in heating will be dissolved nearby the peak temperature and re-precipitated in cooling. - Abstract: To shorten production period and reduce manufacturing cost of high strength aluminum alloy integral panel components, a novel non-isothermal creep age forming (CAF) technology was developed. Taking an Al-Zn-Mg-Cu alloy as the case material, the non-isothermal creep aging (NICA) behavior and the conventional isothermal creep aging (ICA) behavior were comparatively investigated. The corresponding creep deformations, material performance variations and precipitate microstructure evolutions were studied by creep aging tests, mechanical property and corrosion resistance tests, and transmission electron microscope (TEM) and scanning electron microscope (SEM) characterizations. Unlike the ICA which contains short heating and cooling stages and long holding stage, the NICA only has heating and cooling stages, viz., the alloy is heated slowly and the cooling stage begins immediately when reaching the peak temperature. In the NICA process, the precipitates nucleate and grow up in the first half of heating stage, resulting in the reduction of creep rate and enhancement of mechanical strength. The coarsening of precipitates occurs in the second half of heating stage, elevating the creep rate and significantly improving the corrosion resistance. Nearby the peak temperature, the primary precipitates partially dissolve, and the creep rate, mechanical strength and corrosion resistance decrease. Distinctive from the ICA process, a secondary precipitation phenomenon takes place in the cooling stage of NICA, leading to the recovery of high mechanical strength. The higher heating-cooling rate (1 °C/min) is not beneficial to accumulating creep deformation in the shorter creep aging period, while the lower one (0.25 °C/min) causes the loss of mechanical strength due to the excessive dissolution of precipitates. The moderate heating-cooling rate (0.5 °C/min) can lead to larger creep deformation, better mechanical properties and more satisfactory corrosion resistances in the NICA treated alloy, reaching 87.0% of creep strain, 105.7% of yield strength and 97.9% of electric conductivity in the ICA treated alloy. It is worth noting that the time consumption of the optimal NICA process is only 52.9% of the ICA process.

36 MATERIALS SCIENCE↗

Effect of n-HA content on the isothermal crystallization, morphology and mechanical property of n-HA/PLGA composites

Graphical abstract: Effect of n-HA content on the isothermal crystallization, morphology and mechanical property of n-HA/PLGA composites was studied in details. The results showed that the addition of higher content of g-n-HA was favorable to promote the crystallization better in g-n-HA/PLGA composites, but it could also cause more agglomeration in PLGA matrix, as a result of worse mechanical properties, and the addition content of 3 wt% g-n-HA to PLGA matrix was an appropriate proportion, which had the highest bending strength among these g-n-HA/PLGA composites, and it might be potential to be used in biomedical fields in future. Highlights: ► The effect of n-HA content on the n-HA/PLGA composites was studied in detail. ► Isothermal crystallization, microstructure and mechanical property were studied. ► The relation between n-HA content and properties of n-HA/PLGA composite was found. ► An appropriate proportion of n-HA in n-HA/PLGA composite was obtained. - Abstract: A serials of g-n-HA/PLGA composites with surface-modified g-n-HA of 1%, 3%, 6%, 10% and 15% in weight were prepared by solution mixing. The isothermal crystallization, morphology and mechanical property of g-n-HA/PLGA composites were investigated by differential scanning calorimeter (DSC), scanning electron microscope (SEM) and electromechanical universal tester. The results showed that Avrami equation was suitable for describing the isothermal crystallization process in this system, and the crystallization rate of g-n-HA/PLGA composites containing more than 3 wt% g-n-HA was basically accord with the relational expression of T{sub 110} {sub °C} > T{sub 105°C} > T{sub 115°C} > T{sub 120°C}. Moreover, at the same Tc, crystallization rate was greatly enhanced with the increasing of g-n-HA acting as nucleate. However, the addition of higher content of g-n-HA would cause more agglomeration in PLGA matrix, so that the mechanical properties of g-n-HA/PLGA composites would gradually decrease. In conclusion, the addition of higher content of g-n-HA was favorable to promote the crystallization better in g-n-HA/PLGA composites, but it could also cause more agglomeration in PLGA matrix, result in worse mechanical properties, and the addition content of 3 wt% g-n-HA to PLGA matrix was an appropriate proportion, which had the highest bending strength among these g-n-HA/PLGA composites, and it might be potential to be used in biomedical fields in future.

36 MATERIALS SCIENCE↗

Temperature-Dependent Kinetic Prediction for Reactions Described by Isothermal Mathematics

Most kinetic models are expressed in isothermal mathematics. In addition, this may lead unaware scientists either to the misconception that classical isothermal kinetic models cannot be used for any chemical process in an environment with a time-dependent temperature profile or, even worse, to a misuse of them. In reality, classical isothermal models can be employed to make kinetic predictions for reactions in environments with time-dependent temperature profiles, provided that there is a continuity/conservation in the reaction extent at every temperature–time step. In this article, fundamental analyses, illustrations, guiding tables, and examples are given to help the interested readers using either conventional isothermal reacted fraction curves or rate equations to make proper kinetic predictions for chemical reactions in environments with temperature profiles that vary, even arbitrarily, with time simply by the requirement of continuity/conservation of reaction extent whenever there is an external temperature change.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding Solvent-Induced Glass Transition in Polymer Thin Films Using Absorption–Desorption Isotherms

The fundamental thermodynamic and mechanical underpinnings of polymer thin films exposed to solvent vapor are critical for the development of advanced nanolithography and high-performance coatings. This work investigates the solvent− polymer interactions of glassy thin films by using the solvent absorption−desorption isotherms. An analogous relationship to the Flory−Fox equation was observed between solvent−induced glass transition, swelling, Flory−Huggins interaction parameter, and molecular weight. Isothermal swelling measurements revealed that the glass transition trends are more robust in the absorption curve compared to desorption, contrary to previous reports. Excess osmotic pressure analysis of the isotherm provides a measure of the degree of physical aging in thin films annealed below the glass transition. This is further validated in the ordering of block copolymer (BCP) films annealed at low solvent activity. In agreement with the thermal analysis, free-surface plasticization effects become the most prominent below 100 nm. However, solvent annealing is largely dependent on solvent mass transport, as made evident by the strong dependence on solvent viscosity. From these observations, four general types of isotherms are identified that graphically capture distinct solvent−polymer interaction regimes. More broadly, these results inform solvent vapor annealing-induced self-assembly, sequential infiltration synthesis, membrane-based separations, adsorptive processes, and swelling-based responsive materials design.

Hendeniya, Nayanathara [Iowa State Univ., Ames, IA↗

Isothermal solidification for high-entropy alloy synthesis

Kinetically trapping the high-temperature states through rapid cooling solidification is widely used for the synthesis of high-entropy alloys (HEAs), especially those with intrinsically immiscible elemental combinations. However, strategies need to be developed to overcome the fundamental limitations of rapid cooling solidification in controlling the crystallinity, structure and morphology of HEAs. Here, in this study, we introduce an isothermal solidification strategy for the synthesis of HEAs by rapidly altering the metal alloy composition through liquid–liquid interface reactions at low temperatures, for example, from 25 °C to 80 °C. We use gallium (Ga)-based metal as the sacrificial reagent and mixing medium. By directing the reactions to the interfaces between the Ga-based liquid metal and an aqueous metal ion solution, the foreign metal ions can be reduced at the interfaces and incorporated into the liquid metal quickly. HEAs with various crystallinity (single crystal, mesocrystal, polycrystal and amorphous), morphology (zero, two and three dimensions) and compositions can be achieved through the isothermal solidification. Ga can be completely consumed, resulting in Ga-free HEAs. If desired, Ga can be one of the metal elements in the final products. In situ liquid phase transmission electron microscopy (TEM) studies and theoretical analysis show the isothermal solidification mechanisms. Our direct observations show the enhanced mixing of liquid metal elements and the solidification process with fluctuating nucleation dynamics. The isothermal solidification marks a powerful strategy for HEA synthesis through an unexplored pathway of kinetically trapping the high-entropy states.

Zhang, Qiubo [Lawrence Berkeley National Laborator↗

Measurement of Palladium Hydride and Palladium Deuteride Isotherms Between 130 K and 393 K

The data collected in the present work extend the measured phase diagram for palladium hydride and palladium deuteride to a region that has been sparsely reported in open literature. Absorption isotherms were measured using a 2.5-g bed of palladium powder at temperatures between 130 K and 393 K and pressures less than 1.3 x 10 5 Pa. Such low-pressure and low-temperature measurements are useful for characterizing palladium beds used for tritium pumping and storage. For tritium storage, pressures are kept below a few millibar for safety reasons. Low temperatures increase the tritium storage capacity of palladium. The measured absorption isotherms show the well-documented, two-phase behavior for this system: two solubility regions and a mixed, hydride-forming region. The isotherms show that an increased quantity of hydride is formed at lower temperatures, as marked by an increase in the hydride-forming region. This region exceeds hydrogen to metal ratios of 0.75 for T ≤ 273 K. Equilibrium pressures in the mixed region decrease with decreasing temperatures until a critical temperature is reached for each isotope. Below these critical temperatures, the rate of pressure decrease with decreasing temperature is significantly reduced. This change in trend suggests hydrogen isotopes are adsorbed onto the palladium surface, rather than forming a hydride. Using the equilibrium pressures recorded at temperatures between 236 K and 393 K for protium and between 211 K and 354 K for deuterium, the van’t Hoff constants were calculated to be A = –36 ± 1 kJ/mol and B = 88 ± 3 J/K for protium and A = -32 ± 2 kJ/mol and B = 88 ± 9 J/K for deuterium. As a result, these constants agree favorably with literature in the range where the temperatures of the measured isotherms overlap.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ON THE HORSESHOE DRAG OF A LOW-MASS PLANET. I. MIGRATION IN ISOTHERMAL DISKS

We investigate the unsaturated horseshoe drag exerted on a low-mass planet by an isothermal gaseous disk. In the globally isothermal case, we use a formalism, based on the use of a Bernoulli invariant, that takes into account pressure effects, and that extends the torque estimate to a region wider than the horseshoe region. We find a result that is strictly identical to the standard horseshoe drag. This shows that the horseshoe drag accounts for the torque of the whole corotation region, and not only of the horseshoe region, thereby deserving to be called corotation torque. We find that evanescent waves launched downstream of the horseshoe U-turns by the perturbations of vortensity exert a feedback on the upstream region, that render the horseshoe region asymmetric. This asymmetry scales with the vortensity gradient and with the disk's aspect ratio. It does not depend on the planetary mass, and it does not have any impact on the horseshoe drag. Since the horseshoe drag has a steep dependence on the width of the horseshoe region, we provide an adequate definition of the width that needs to be used in horseshoe drag estimates. We then consider the case of locally isothermal disks, in which the temperature is constant in time but depends on the distance to the star. The horseshoe drag appears to be different from the case of a globally isothermal disk. The difference, which is due to the driving of vortensity in the vicinity of the planet, is intimately linked to the topology of the flow. We provide a descriptive interpretation of these effects, as well as a crude estimate of the dependency of the excess on the temperature gradient.

79 ASTRONOMY AND ASTROPHYSICS↗

Generalized definition of the isothermal compressibility in (2+1)-flavor QCD

We introduce a generalized definition of the isothermal compressibility ($𝜅_{𝑇,𝜎{^2_𝑄}}$) calculable by keeping net conserved charge fluctuations rather than total number densities constant. We present lattice QCD results for this isothermal compressibility, expressed in terms of fluctuations of conserved charges that are related to baryon (𝐵), electric charge (𝑄), and strangeness (𝑆) quantum numbers. This generalized isothermal compressibility is compared with hadron resonance gas model calculations as well as with heavy-ion collision data obtained at RHIC and the LHC. We find $𝜅_{𝑇,𝜎{^2_𝑄}}$ = 13.8⁢(1.3) fm 3 /GeV at $𝑇_{\textrm{pc},0}$ =156.5⁢(1.5) MeV and $\hat{𝜇}_𝐵$ = 0. This finding is consistent with the rescaled result of the ALICE Collaboration, where we replaced the number of charged hadrons (𝑁 ch ) by the total number of hadrons (𝑁 tot ) at freeze-out. Normalizing this result with the QCD pressure (𝑃) we find that the isothermal compressibility on the pseudocritical line stays close to that of an ideal gas, i.e., $𝑃⁢𝜅_{𝑇,𝜎{^2_𝑄}} ≃$ 1.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Liquid Piston with Spray Cooling Near-Isothermal Compressor

The goal of this project was to prototype and characterize the performance of a liquid-piston spray-cooled gas compressor. The working principle of the compressor enables optimized high-efficiency operation over a very wide range of operating conditions, unlike conventional compressors that are optimized for a narrow range of operating conditions. The compressor technology is suitable for many applications, such as gas pipeline transport, gas storage, and commercial and residential heat pumps. Both physical testing and computational fluid dynamics (CFD) modeling of the processes using the Oak Ridge National Laboratory high-performance computing center were completed. The experimental and CFD studies focused on a near-isothermal liquid-piston compressor (LPC) that uses propylene glycol to compress CO 2 . The first prototype demonstrated isothermal operation during several sequentially executed cycles of CO 2 compression and raised the temperature of the compressed CO 2 by only 2 K, compared with approximately 6 K when the gas was compressed non-isothermally. Isothermal operation was demonstrated at CO 2 flow rates of up to 2 L/min. The second prototype was designed with two compression chambers to allow continuous flow of high-pressure CO 2 . However, the design of the valve train to direct flow between the compression chambers was not sufficient to allow demonstration of CO 2 compression. Numerical simulations of the LPC in which the compression chamber was filled with propylene glycol injected from the bottom inlet were performed using large eddy simulation (LES) with the wall-adapting local eddy-viscosity subgrid-scale model coupled with the multiphase volume of fluid (VOF) model to simulate the transient interface between gas and liquid and to capture the heat and mass transfers within the compression chamber. In this effort, the effects of boundary conditions applied to the LES-VOF calculations (i.e., no wall, an adiabatic wall, and a wall with a heat flux subscribed) on the overall pressure and temperature of the CO 2 gas as well as the transient evolution of flow and heat transfer within the compression chamber were investigated and are discussed in this report. The LES calculation with no wall showed no dynamical flow patterns, and the volume-averaged temperature of CO 2 increased from 305 to 392.7 K, whereas LES calculations with a constant wall temperature or a wall heat flux had similar increases of CO 2 temperatures. The results of the LES simulation using a wall heat flux showed different stages in the compression process and revealed dynamical formation and interaction of CO 2 gas layers and circulation flow patterns within the chamber that contributed to the overall heat transfer between the solid wall, gas, and liquid surface in the compressor. Though an industrial partnership for commercializing the compressor was not secured, the technology was attractive for an industrial partner to use in two research proposals in response to US Department of Energy funding opportunity announcements.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Evaluation of the Initial Isothermal Physics Measurements at the Fast Flux Test Facility, a Prototypic Liquid Metal Fast Breeder Reactor

The Fast Flux Test Facility (FFTF) was a 400-MWt, sodium-cooled, low-pressure, high-temperature, fast-neutron flux, nuclear fission reactor plant designed for the irradiation testing of nuclear reactor fuels and materials for the development of liquid metal fast breeder reactors (LMFBRs). The FFTF was fueled with plutonium-uranium mixed oxide (MOX) and reflected by Inconel-600. Westinghouse Hanford Company operated the FFTF as part of the Hanford Engineering Development Laboratory (HEDL) for the U.S. Department of Energy on the Hanford Site near Richland, Washington. Although the FFTF was a testing facility not specifically designed to breed fuel or produce electricity, it did provide valuable information for LMFBR projects and base technology programs in the areas of plant system and component design, component fabrication, prototype testing, and site construction. The major objectives of the FFTF were to provide a strong, disciplined engineering base for the LMFBR program, provide fast flux testing for other U.S. programs, and contribute to the development of a viable self-sustaining competitive U.S. LMFBR industry. During its ten years of operation, the FFTF acted as a national research facility to test advanced nuclear fuels, materials, components, systems, nuclear power plant operating and maintenance procedures, and active and passive reactor safety technologies; it also produced a large number of isotopes for medical and industrial users, generated tritium for the U.S. fusion research program, and participated in cooperative, international research work. Prior to the implementation of the reactor characterization program, a series of isothermal physics measurements were performed; this acceptance testing program consisted of a series of control rod worths, critical rod positions, subcriticality measurements, maximum reactivity addition rates, shutdown margins, excess reactivity, and isothermal temperature coefficient reactivity. The results of these experiments were of particular importance because they provide extensive information which can be directly applied to the design of large LMFBR’s. It should be recognized that the data presented in the initial report were evaluated only to the extent necessary to ensure that adequate data were obtained. Later reports provided further interpretation and detailed comparisons with prediction techniques. The conclusion of the isothermal physics measurements was that the FFTF nuclear characteristics were essentially as designed and all safety requirements were satisfied. From a nuclear point of view, the FFTF was qualified to proceed into power operation mode. The FFTF was completed in 1978 and first achieved criticality on February 9, 1980. Upon completion of the isothermal physics and reactor characterization programs, the FFTF operated for ten years from April 1982 to April 1992. Reactor operations of the FFTF were terminated and the reactor facility was then defueled, deactivated, and placed into cold standby condition. Deactivation of the reactor was put on hold from 1996 to 2000 while the U.S. Department of Energy examined alternative uses for the FFTF but then announced the permanent deactivation of the FFTF in December 2001. Its core support basket was later drilled in May 2005, so as to remove all remaining sodium coolant. On April 17, 2006, the American Nuclear Society designated the FFTF as a “National Nuclear Historic Landmark”.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The physical implications of an isothermal model for the hot intracluster medium

HEAO-1 A-2 and Einstein Observatory IPC observations of 15 clusters of galaxies have been used to measure the isothermal beta-model parameters, and the parameters are compared with those derived from model fits to the X-ray images. The physical constraints imposed on this model by existing optical data, the implied gas mass, and the gas contribution to the binding cluster mass are addressed. Values of beta less than unity are obtained, consistent with results from X-ray imaging data. This is interpreted to imply that the gas extends out to 8-10 core radii, about 2-3 Mpc. The isothermal gas mass can be as large as 60 percent of the virial mass for some clusters. This contradicts the fundamental assumption that the cluster potential is determined by an unseen mass which is given by the King approximation to an isothermal sphere, and it is concluded that the isothermal model is a nonphysical model.

Henriksen, M. J.↗

Calculation of thermomechanical fatigue life based on isothermal behavior

The isothermal and thermomechanical fatigue (TMF) crack initiation response of a hypothetical material was analyzed. Expected thermomechanical behavior was evaluated numerically based on simple, isothermal, cyclic stress-strain - time characteristics and on strainrange versus cyclic life relations that have been assigned to the material. The attempt was made to establish basic minimum requirements for the development of a physically accurate TMF life-prediction model. A worthy method must be able to deal with the simplest of conditions: that is, those for which thermal cycling, per se, introduces no damage mechanisms other than those found in isothermal behavior. Under these assumed conditions, the TMF life should be obtained uniquely from known isothermal behavior. The ramifications of making more complex assumptions will be dealt with in future studies. Although analyses are only in their early stages, considerable insight has been gained in understanding the characteristics of several existing high-temperature life-prediction methods. The present work indicates that the most viable damage parameter is based on the inelastic strainrange.

Halford, Gary R.↗

Calculation of thermomechanical fatigue life based on isothermal behavior

The isothermal and thermomechanical fatigue (TMF) crack initiation response of a hypothetical material was analyzed. Expected thermomechanical behavior was evaluated numerically based on simple, isothermal, cyclic stress-strain-time characteristics and on strainrange versus cyclic life relations that have been assigned to the material. The attempt was made to establish basic minimum requirements for the development of a physically accurate TMF life-prediction model. A worthy method must be able to deal with the simplest of conditions: that is, those for which thermal cycling, per se, introduces no damage mechanisms other than those found in isothermal behavior. Under these assumed conditions, the TMF life should be obtained uniquely from known isothermal behavior. The ramifications of making more complex assumptions will be dealt with in future studies. Although analyses are only in their early stages, considerable insight has been gained in understanding the characteristics of several existing high-temperature life-prediction methods. The present work indicates that the most viable damage parameter is based on the inelastic strainrange.

Halford, G. R.↗

Isothermal and nonisothermal fatigue behavior of a metal matrix composite

The isothermal and nonisothermal fatigue resistance of a metal matrix composite (MMC) consisting of Ti-15V-3Cr-3Al-3Sn (Ti-15-3) matrix reinforced by 33 vol pct continuous SiC fibers was investigated. The fibers were nominally oriented parallel to the specimen axis. Isothermal fatigue tests were performed in air at 300 and 550 C. The MMC had good isothermal fatigue resistance at low cyclic stress, with fatigue cracks initiating from fiber-matrix interfaces and foil laminations. At high cyclic stresses, stress relaxation in the matrix reduced isothermal composite fatigue resistance at 550 C. Nonisothermal fatigue loading substantially degraded composite fatigue resistnce. This degradation was produced by a thermomechanical fatigue damage mechanism associated with the fiber-matrix interfaces.

Gabb, T. P.↗

An analysis of isothermal, bithermal, and thermomechanical fatigue data of Haynes 188 and B1900+Hf by energy considerations

The low-cycle fatigue behavior of Haynes 188 and B1900+Hf under isothermal, bithermal, and thermomechanical loading conditions has been analyzed on the basis of the total hysteresis energy expended per cycle. It has been observed that in the case of isothermal fatigue the total hysteresis energy correlates well with the fatigue life. In the case of bithermal 'high rate' fatigue, for a given total hysteresis energy per cycle, the fatigue life is equal to or greater than the isothermal fatigue life at the maximum bithermal temperature. This observation could be used to establish a lower bound on life for design purposes. In one case of bithermal creep-fatigue and in thermomechanical fatigue, the life is shorter than that corresponding to the isothermal life at the maximum temperature. The energy supplied, per se, may not always give a systematic correlation with the fatigue life in the cases where time-dependent creep and environmental effects are encountered. Thus, in bithermal creep-fatigue and thermomechanical fatigue, the role of creep and environment and their dependence on the energy supplied have to be properly accounted for before the energy term can be used for life prediction.

Radhakrishnan, V. M.↗