Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ION CURRENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

The Role of Magnetic Reconnection in Energizing Protons and Heavier Ions at the Heliospheric Current Sheet

During near-Sun crossings of the heliospheric current sheet (HCS), Parker Solar Probe (PSP) observed populations of high-energy protons and heavier ions, indicating possible energization by magnetic reconnection up to 10 s–100 s keV nucleon −1 . Here we study ion acceleration by magnetic reconnection at the HCS. To estimate ion energization, we solve the Parker transport equation coupled to a large-scale 2D MHD reconnection simulation. We find that multiple ion species develop power-law distributions with both spectral index and high-energy cutoff E max consistent with in situ data. By accounting for the injection physics determined by kinetic simulations, we confirm that the charge-to-mass ratio scales as E max ∝ (Q/M) α with α ∼ 0.8–1.1, approximately consistent with PSP measurements in the broader range α ∼ 0.6–1.7. In the limit where ions are injected at the same energy per nucleon, α can be as low as ∼0.3. These findings further support the role of magnetic reconnection in producing high-energy heavy ions at the HCS.

Murtas, Giulia [West Virginia Univ., Morgantown, W↗
DOE OSTI2020

Review of Ion Exchange Technologies for Cesium Removal from Caustic Tank Waste

This article reviews the historical uses of and current research into ion exchange for the removal of cesium (Cs) from defense-related nuclear waste streams. Emphasis is placed on key attributes of the two current leading ion exchangers for Cs removal: spherical resorcinol-formaldehyde, an elutable organic resin, and crystalline silicotitanate, a non-elutable crystalline solid. An understanding of the successes, issues, and limitations of past ion exchange experience may be helpful in better understanding current ion exchanger use. Emphasis is placed on Cs capacity, exchange kinetics, stability, and column hydrodynamics for processing alkaline wastes as well as the final waste forms of the ion exchangers.

Fiskum, Sandra K.↗
DOE OSTI2020

Effects of dissipative baryon current in heavy-ion collisions at RHIC-BES energies

The CLVisc (3+1)D viscous hydrodynamic model is extended to include the equation of net baryon conservation and the Israel-Stewart-like equations for dissipative baryon current. Using the NEOSB equation of state, we simulate the dynamical evolution and collectivity of the quark-gluon plasma with finite chemical potential, assuming smooth energy density and net baryon density distributions at the initial proper time. Numerical results are shown for the impact of net-baryon dissipation on particle yields and p T spectra in heavy-ion collisions at beam energy scan energies.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Effect of parallel flow on resonant layer responses in high beta plasmas

Abstract Resonant layers in a tokamak respond to non-axisymmetric magnetic perturbations by amplifying the mode amplitude and balancing the plasma rotation through magnetic reconnection and force balance, respectively. This resonant response can be characterized by local layer parameters and especially by a single quantity in the linear regime, the so-called inner-layer Δ. The computation of Δ under two-fluid drift-MHD formalism has been progressed by reducing the order of the system in the phase space, where the shielding current is approximated as being only carried by electrons, a posteriori . In this study, we relax the approximation and compute Δ accounted for by the parallel flow associated with the ion shielding current. The posteriori is numerically verified in great agreement with the original SLAYER developed in a previous paper (J.-K. Park 2022 Phys. Plasmas 29 072506). Extending the resonant layer response theory to high β plasmas, our research findings answer two important questions: how the parallel flow influences the resonant layer response and why the parallel flow effect appears in high β plasmas. The complicated plasma compression in high β regime allows the parallel flow response to give rise to the ion shielding current, which not only shifts the zero-crossing condition of the ExB flow but also enhances the field penetration threshold. Technically, the Riccati matrix transformation method is adapted to handle the numerical stiffness due to the increased order of the system. The high fidelity of this numerical method makes use of further extension of the model to higher-order systems to take other physical phenomena into account. This work is envisaged to predict the resonant layer response under high β fusion reactor conditions.

Lee, Yeongsun (ORCID:000000034474416X)↗
DOE OSTI2025

The MIST-1 and MIST-2 multicusp ion sources for high-current $H$$^{+}_{2}$ beams

We present two iterations of the Multicusp Ion Source Technology at MIT (MIST) sources, designed to fulfill the requirements of the HCHC-XX cyclotron design. The HCHC-XX is a novel compact cyclotron accelerating $H$$^{+}_{2}$. Beam is injected through a radio-frequency quadrupole buncher-accelerator (embedded in the cyclotron yoke) and utilizes so-called vortex motion during acceleration. If successful, it will deliver 10 mA of protons at 60 MeV in CW mode. This scheme requires a low-emittance, high-current initial beam with high $H$$^{+}_{2}$ purity. We briefly summarize the design and previous results of the MIST-1 ion source and, for the first time, the detailed design of the new and improved MIST-2, including the mechanical, electrical, and control system design. We further show experimental results of using the MIST-2 backplate on the MIST-1 body, present a study using different types of permanent magnets for confinement (including no magnets), and finally, we present first results of the MIST-2 in full operation. In this first commissioning run, we were able to increase the total extracted current from the MIST-2 to 7 mA—a factor of 2 over the MIST-1.

Winklehner, D. [Massachusetts Institute of Technol↗
DOE OSTI2025

High tensile alloy of copper to mitigate current collector deformation in silicon electrodes for lithium-ion batteries

The volumetric changes of silicon electrodes, along with the strong adhesive properties of certain binders, can lead to plastic deformation of the current collector and create damage in the electrode coating. Here, in this study, we report a detailed study of silicon coatings on a high-tensile alloy (HTA) foil of copper with strength over twice that of conventional copper foils. The HTA current collectors with high mechanical strength can mitigate plastic deformation upon continuous cycling. At moderate areal capacities (2.5–3 mAh cm −2 ), conventional copper foils show significant wrinkling after only a few electrochemical cycles, whereas the HTA foils remain intact. We demonstrate viability of the HTA foils in large format xx6395 pouch cells, in which the HTA current collectors remain intact even at an areal capacity of 4.5 mAh cm −2 ; in contrast, wrinkles form in conventional copper current collectors increasing the likelihood of lithium plating. Computational studies show that stresses generated during cycling of silicon electrodes are very high in the current collector and at the current collector-coating interface, explaining the wrinkling of conventional Cu foils. Our studies highlight importance of current collector to solve the electrochemical and chemo-mechanical performance challenges associated with high-loading silicon electrodes.

Chemo-mechanical degradation↗
DOE OSTI2025

New model for the ion collection by cylindrical probes over a wide range of collisionality

Langmuir probes remain one of the most important diagnostic tools for plasma processing applications. Modern probe analysis usually relies on the electron current part of the Langmuir probe characteristic using the Druyvesteyn method. However, for electronegative plasmas or for discharges containing dust the analysis of the ion current attracted by the probe can be desirable to determine the ion density. But, even at low pressures of a few Pa, the ion current is affected by collisions due to the large cross section for charge exchange. Available theories for collisional or collision-enhanced ion currents onto probes are complex and not well validated. Thus, in this contribution, we compare available collisional probe theories for the ion current to results of particle-in-cell (PIC) simulations. To this end, the probe surrounded by a semi-infinite plasma is simulated using a modified version of the open-source code EDIPIC. A dataset of currents for different neutral gas pressures is obtained and compared to the different theories from the literature. Based on these results, we propose a simpler and more intuitive model for the ion current collected by the probe, based on the model of Gatti and Kortshagen (Phys. Rev. E 78, 046402, 2008), developed for the charging of dust particles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Probe the Localized Electrochemical Environment Effects and Electrode Reaction Dynamics for Metal Batteries using In Situ 3D Microscopy

Uncontrollable dendrite growth is closely related to non-uniform reaction environments. However, there is a lack of understanding and analysis methods to probe the localized electrochemical environment (LEE). Here the effects of the LEE are investigated, including localized ion concentrations, current density, and electric potential, on metal plating/stripping dynamics and dendrite minimization. A novel in situ 3D microscopy technique is developed to image the morphology dynamics and deposition rate of Zn plating/stripping processes on 3D Zn–Mn anodes. Using the in situ 3D microscope, the electrode morphology changes during the reactions are directly imaged and Zn deposition rate maps at different time points are obtained. It is found that reaction kinetics are highly correlated to LEE and electrode morphology. To further quantify the LEE effects, the digital twin technique is employed that allows the accurate calculation of the electrochemical environments, such as localized ion concentrations, current density, and electric potential, which cannot be directly measured from experiments. We found that the curvature of the 3D electrode surface determines the LEE and significantly influences reaction kinetics. This provides a new strategy to minimize the dendrite formation by designing and optimizing the 3D geometry of the electrode to control the LEE.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electrodialysis through nafion membranes coated with polyelectrolyte multilayers yields >99% pure monovalent ions at high recoveries

Separation of monovalent and multivalent ions is important in processes ranging from water softening to recycling of Li. Previous studies show that cation-exchange membranes coated with multilayer polyelectrolyte films exhibit monovalent/divalent ion selectivities as high as 1000 in electrodialysis (ED) under ideal conditions with low ion recoveries. This work shows that even at 60-80% monovalent-ion recoveries, ED through Nafion membranes coated with protonated poly(allylamine)/poly(4-styrenesulfonate) multilayers can separate equimolar K + and Mg 2+ or Li + and Mg 2+ to give 99.5% pure monovalent ion. Moreover, the use of a low-volume receiving phase allows ED to concentrate the monovalent ion. Typical current efficiencies are around 70% for these separations. Selectivities appear to increase when the membrane-coating procedure uses a higher polyelectrolyte concentration in the deposition solution. Because the limiting current declines with ED time due to depletion of the monovalent ion in the source phase, use of a gradually decreasing applied current enhances current efficiency compared to ED at a constant high current. Further, the membranes also show Li + /Mg 2+ selectivities around 100 when Mg 2+ is in a 20-fold excess in the source phase at an ionic strength of 0.6 M, but selectivity decreases at even higher ionic strengths.

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

Metal-ion-controlled growth and nanoindentation response of 3D, bicontinuous Cu–Fe thin films

Bicontinuous, nanocomposite thin film morphologies depend largely on the deposition conditions applied during physical vapor deposition. With the introduction of high power impulse magnetron sputtering (HiPIMS), the range of potential morphologies achieved during deposition has been increased. In this work, we compare the deposition outcomes between traditional direct-current magnetron sputtering (DCMS) and HiPIMS for a thin film co deposit of Cu and Fe. Modular control of the columnarity, porosity and roughness was achieved by varying the Cu and Fe metal ion currents during deposition. The directionality of the nanostructured phase-separated morphology was also controlled as the ion current increased. At zero ion current for both Cu and Fe sputtered species during DCMS, the film exhibited lateral concentration modulations of Cu and Fe. The directionality of the Cu- and Fe-rich phases shifted to vertical concentration modulations at low ion currents of I Fe = 1A and I Cu = 0:1A and to lateral concentration modulations at relatively moderate ion currents of I Fe = 5A and I Cu = 2A: At high ion currents of I Fe = 18A and I Cu = 2A; a more randomized phase domain structure was observed on the nanoscale. This structural shift is rationalized using an interdiffusion model. Here, the role of different kinds of phase separated morphologies, achieved during DCMS deposition, on the mechanical properties has also been studied. Results indicated increase in hardness, indentation modulus and flow strength values with the increase in indentation strain rates. Bicontinuous Cu-Fe nanocomposites are found to be stronger than multilayer Cu-Fe samples.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ytterbium ion trap quantum computing: The current state-of-the-art

In this work, we present an overview of contemporary quantum computing with ytterbium ion traps, placing the emphasis on industry implementations. We provide brief, concrete descriptions of various key features, such as trap loading, electronic structure, qubit function, gates, error analysis, and benchmarking. We focus on the underlying science and current technologies to provide readers with a holistic picture of available techniques for using ytterbium in contemporary ion trap designs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Polymers in Lithium‐Ion and Lithium Metal Batteries

Abstract Lithium‐ion batteries play a significant role in modern electronics and electric vehicles. However, current Li‐ion battery chemistries are unable to satisfy the increasingly heightened expectations regarding energy demand and reliability. To boost the overall energy density while ensuring the safety of Li batteries, researchers have focused on alternative battery materials, such as silicon, sulfur, and Li metal. These represent promising avenues, although numerous obstacles (e.g., Si cracking, polysulfide shuttling, Li dendrites, etc.) must be tackled before batteries based on these materials can enter mass production and penetrate the mainstream market. Polymers are a class of materials that are widely used in current battery systems; however, many novel polymer chemistries may offer better performance and reliability than the current ones, and even overcome the issues of the above‐mentioned new battery materials. In this review, selected polymeric materials for solving these issues are categorized into four parts: polymer electrolytes, polymer artificial solid‐electrolyte interphases, binders, and separators. Both the current progress and the characterization methods are included. Potential future directions of energy materials research are pointed out as well.

Li, Junheng↗
DOE OSTI2025

Investigation of divertor detachment induced through neon seeding and density ramp on HL-3

A new self-consistent 1D scrape-off layer model has been recently developed in BOUT++ framework, named SD1D, which includes equations for various particle species (e.g. main plasma, neutrals and impurities) and couples open databases like ADAS and AMJUEL. It is able to quickly and effectively simulate divertor detachment experiments. In this work, a typical detachment experiment (shot #6270) on HL-3 with neon seeding is simulated using the SD1D code. It is found that the target electron temperature and the target ion saturation current in the simulations are consistent with experimental results measured by Langmuir probes on the target plate. The variation of D α radiation intensity in the divertor is qualitatively similar to the measured D α signal. Following the experimental validations, different upstream densities are set in the simulations to study the impurity distribution under different plasma density conditions. It is found that increasing upstream density can be helpful for the control of the neon radiation front (closer to the target). In this work we also compare two detachment regimes in simulations. Based on the same initial experimental parameters (shot #6270) on HL-3, a scan of upstream density and a scan of neon seeding rate are carried out respectively. It is found that the role of atomic and molecular processes is different in the two detachment regimes. The current density roll-over is ascribed to a drop in the divertor ion source, and the variation of D α radiation intensity via different excitation channels is associated with the relevant collisional reaction sources.

BOUT++↗
DOE OSTI2021

Separation of cobalt, nickel, and manganese in leach solutions of waste lithium-ion batteries using Dowex M4195 ion exchange resin

Current methods to separate and recover critical metals from waste lithium-ion battery (LIB) scrap require multiple unit operations that involve selective leaching and a combination of separation methods. These methods include impurity removal, solvent extraction, ion exchange, and precipitation, to achieve high purity Co and Ni products. In this paper an efficient extraction strategy was developed to individually separate Ni and Co from a LIB leachate that was generated from an electrochemical leaching process. By using Dowex M4195 resin, as the only method of separation, additional impurity removal operations were not needed. After loading and eluting, three different fractions were obtained: 99.0% Ni concentrate, 98.5% Co concentrate, and a Li/Mn rich concentrate allowing the separation of Ni, Co and Mn. Here, the developed process is then presented as an alternative for metal recovery from leachates from scrap LIBs with minimum chemical addition and pH adjustment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Constructing “Li-rich Ni-rich” oxide cathodes for high-energy-density Li-ion batteries

The current exploration of high-energy-density cathode materials for Li-ion batteries is mainly concentrated on either so-called “Li-rich” or “Ni-rich” oxides. However, both are suffering from formidable practical challenges. Here, we combine these two concepts to obtain “Li-rich Ni-rich” oxides in pursuit of more practical high-energy-density cathodes. As a proof of concept, we synthesized an array of Li 1+y Ni( 3-5y)/3 Mo 2y/3 O 2 oxides, whose structures were identified to be the coexistence of LiNiO 2 -rich and Li 4 MoO 5 -rich domains with the aid of XRD, TEM, and NMR techniques. Such an intergrowth structure of 5–20 nm size enables excellent mechanical and structural reversibility for the layered rock-salt LiNiO 2 -rich domain upon cycling thanks to the robust cubic rock-salt Li 4 MoO 5 -rich domain enabling an “epitaxial stabilization” effect. As a result, we achieved high capacities (>220 mA h g -1 ) with Ni contents as low as 80%; the Li 1.09 Ni 0.85 Mo 0.06 O 2 member (y = 0.09) shows much improved cycling performances (91% capacity retention for 100 cycles at C/10) compared with pure LiNiO 2 . Further, this work validates the feasibility of constructing Li-rich Ni-rich compounds in the form of intergrowing domains and hence unlocks vast possibilities for future cathode design.

25 ENERGY STORAGE↗
DOE OSTI2022

Effects of polarization-reversed EMIC waves on the ring current dynamics

Electromagnetic ion cyclotron (EMIC) waves are widely believed to play an important role in influencing the radiation belt and ring current dynamics. Most studies have investigated the effects or characteristics of EMIC waves by assuming their left-handed polarization. However, recent studies have found that the reversal of polarization, which occurs at higher latitudes along the wave propagation path, can change the wave-induced pitch angle diffusion coefficients. Whether such a polarization reversal can influence the global ring current dynamics remains unknown. In this study, we investigate the ring current dynamics and proton precipitation loss in association with polarization-reversed EMIC waves by using the ring current–atmosphere interactions model (RAM). The results indicate that the polarization reversal of H-band EMIC waves can truly decrease the scattering rates of protons of 10 to 50 keV or >100 keV in comparison with the scenario in which the EMIC waves are considered purely left-handed polarized. Additionally, the global ring current intensity and proton precipitation may be slightly affected by the polarization reversal, especially during prestorm time and the recovery phase, but the effects are not large during the main phase. This is probably because the H-band EMIC waves contribute to the proton scattering loss primarily at E < 10 keV, an energy range that is not strongly affected by the polarization reversal.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Large Local Currents in a Lithium-Ion Battery during Rest after Fast Charging

Increasing electric vehicle (EV) adoption requires lithium-ion batteries that can be charged quickly and safely. Some EV batteries have caught on fire despite being neither charged nor discharged. While the lithium that plates on graphite during fast charging affects battery safety, so do the internal ionic currents that can occur when the battery is at rest after charging. These currents are difficult to quantify; the external current that can readily be measured is zero. Here we study a graphite electrode at rest after 6C fast charging using operando X-ray microtomography. We quantify spatially resolved current density distributions that originate at plated lithium and end in underlithiated graphite particles. The average current densities decrease from 1.5 to 0.5 mA cm -2 in about 20 min after charging is stopped. Surprisingly, the range of the stripping current density is independent of time, with outliers above 20 mA cm -2 . In conclusion, the persistence of outliers provides a clue as to the origin of catastrophic failure in batteries at rest.

25 ENERGY STORAGE↗