Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INTERCEPTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

Canted–Cosine–Theta Magnet (CCT)—A Concept for High Field Accelerator Magnets

Canted-Cosine-Theta (CCT) magnet is an accelerator magnet that superposes fields of nested and tilted solenoids that are oppositely canted. The current distribution of any canted layer generates a pure harmonic field as well as a solenoid field that can be cancelled with a similar but oppositely canted layer. The concept places windings within mandrel's ribs and spars that simultaneously intercept and guide Lorentz forces of each turn to prevent stress accumulation. With respect to other designs, the need for pre-stress in this concept is reduced by an order of magnitude making it highly compatible with the use of strain sensitive superconductors such as Nb 3 Sn or HTS. Intercepting large Lorentz forces is of particular interest in magnets with large bores and high field accelerator magnets like the one foreseen in the future high energy upgrade of the LHC. This paper describes the CCT concept and reports on the construction of CCT1 a "proof of principle" dipole.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Water use and radiation balance of miscanthus and corn on marginal land in the coastal plain region of North Carolina

Abstract Miscanthus is a perennial grass that can yield substantial amounts of biomass in land areas considered marginal. In the Coastal Plain region of North Carolina, marginal lands are typically located in coarse‐textured soils with low nutrient retention and water‐holding capacity, and high erosivity potential. Little is known about miscanthus water use under these conditions. We conducted a study to better understand the efficiency with which miscanthus uses natural resources such as water and radiant energy to produce harvestable dry biomass in comparison to corn, a typical commodity crop grown in the region. We hypothesized that under non‐limiting soil water conditions, miscanthus would have greater available energy and water use rates owing to its greater leaf area, thus leading to greater agronomic yields. Conversely, these effects would be negated under drought conditions. Our measurements showed that miscanthus intercepted more radiant energy than corn, which led to greater albedo (by 0.05), lower net radiation (by 4% or 0.4 MJ m −2 day −1 ), and lower soil heat flux (by 69% or 1.0 MJ m −2 day −1 ) than corn on average. Consequently, miscanthus had greater available energy (by 7% or 0.6 MJ m −2 day −1 ) and water use rates (by 14% or 0.5 mm day −1 ) than corn throughout the growing season on average, which partially confirmed our hypothesis. Greater water use rates and radiation interception by miscanthus did not translate to greater water‐use (1.5 g kg −1 vs. 1.6 g kg −1 ) and radiation‐use (0.9 g MJ −1 vs. 1.1 g MJ −1 ) efficiencies than corn. Compared to literature values, our data indicated that water and radiation availability were not limiting at our study site. Thus, it is likely that marginal land features present at the Coastal Plain region such as low soil fertility and high air temperatures throughout the growing season may constrain agronomic yields even if soil water and radiant energy are non‐limiting.

Carvalho, Henrique D. R.↗

National Synchrotron Light Source II storage ring vacuum systems

The National Synchrotron Light Source II, completed in 2014, is a 3-GeV synchrotron radiation (SR) facility at Brookhaven National Laboratory and has been in steady operation since. With a design electron current of 500 mA and subnanometer radians horizontal emittance, this 792-m circumference storage ring is providing the highest flux and brightness x-ray beam for SR users. The majority of the storage ring vacuum chambers are made of extruded aluminium. Chamber sections are interconnected using low-impedance radiofrequency shielded bellows. SR from the bending magnets is intercepted by water-cooled compact photon absorbers resided in the storage ring chambers. This paper presents the design of the storage ring vacuum system, the fabrication of vacuum chambers and other hardware, the installation, the commissioning, and the continuing beam conditioning of the vacuum systems.

43 PARTICLE ACCELERATORS↗

SU-E-T-130: Dosimetric Evaluation of Tissue Equivalent Gel Dosimeter Using Saccharide in Radiotherapy System

Purpose: In this study, the dose responses of the MAGIC gel with various concentrations and type of saccharide are examined to clarify the roles of mono and disaccharide in the polymerization process. Then we focused on the tissue equivalence and dose sensitivity of MAGIC gel dosimeters. Methods: The gel is composed of HPLC, 8% gelatin, 2 × 10-3 M L-ascorbic acid, 1.8 × 10-2 M hydroquinone, 8 × 10-5 M copper(II)sulfate and 9% methacrylic acid, new polymer gels are synthesized by adding glucose(monosaccharide), sucrose(disaccharide) and urea in the concentration range of 5∼35%. For irradiation of the gel, cesium-137 gamma-ray irradiator was used, radiation dose was delivered from 5∼50 Gy. MRI images of the gel were acquired by using a 3.0 T MRI system. Results: When saccharide and urea were added, the O/C, O/N and C/N ratios agreed with those of soft tissue with 1.7%. The dose-response of glucose and sucrose gel have slope-to-intercept ratio of 0.044 and 0.283 respectively. The slope-to-ratio is one important determinant of gel sensitivity. R-square values of glucose and sucrose gel dosimeters were 0.984 and 0.994 respectively. Moreover when urea were added, the slope-to-intercept ratio is 0.044 and 0.073 respectively. R-square values of mono and disaccharide gel were 0.973 and 0.989 respectively. When a saccharide is added into the MAGIC gel dosimeter, dose sensitivity is increased. However when urea were added, dose sensitivity is slightly decreased. Conclusion: In this study, it was possible to obtain the following conclusions by looking at the dose response characteristics after adding mono-, di-saccharide and urea to a MAGIC gel dosimeter. Saccharide was a tendency of increasing dose sensitivity with disaccharide. Sa.ccharide is cost effective, safe, soft tissue equivalent, and can be used under various experimental conditions, making it a suitable dosimeter for some radiotherapy applications.

60 APPLIED LIFE SCIENCES↗

TU-H-CAMPUS-IeP3-04: Evaluation of Changes in Quantitative Ultrasound Parameters During Prostate Radiotherapy

Purpose: Clarity Autoscan ultrasound monitoring system allows acquisition of raw radiofrequency (RF) ultrasound data prior and during radiotherapy. This enables the computation of 3D Quantitative Ultrasound (QUS) tissue parametric maps from. We aim to evaluate whether QUS parameters undergo changes with radiotherapy and thus potentially be used as early predictors and/or markers of treatment response in prostate cancer patients. Methods: In-vivo evaluation was performed under IRB protocol to allow data collection in prostate patients treated with VMAT whereby prostate was imaged through the acoustic window of the perineum. QUS spectroscopy analysis was carried out by computing a tissue power spectrum normalized to the power spectrum obtained from a quartz to remove system transfer function effects. A ROI was selected within the 3D image volume of the prostate. Because longitudinal registration was optimal, the same features could be used to select ROIs at roughly the same location in images acquired on different days. Parametric maps were generated within the rectangular ROIs with window sizes that were approximately 8 times the wavelength of the ultrasound. The mid-band fit (MBF), spectral slope (SS) and spectral intercept (SI) QUS parameters were computed for each window within the ROI and displayed as parametric maps. Quantitative parameters were obtained by averaging each of the spectral parameters over the whole ROI. Results: Data was acquired for over 21 treatment fractions. Preliminary results show changes in the parametric maps. MBF values decreased from −33.9 dB to −38.7 dB from pre-treatment to the last day of treatment. The spectral slope increased from −1.1 a.u. to −0.5 a.u., and spectral intercept decreased from −28.2 dB to −36.3 dB over the 21 treatment regimen. Conclusion: QUS parametric maps change over the course of treatment which warrants further investigation in their potential use for treatment planning and predicting treatment outcomes. Research was supported by Elekta.

60 APPLIED LIFE SCIENCES↗

HALucinator v. 1.0

Scripts that enable emulating firmware by intercepting low-level hardware abstraction function calls and replacing their execution with abstractions of the hardware the intercepted functions are intended to interact with.

Clements, AbrahamA↗

Empirical Estimation of Shortest Route Length along U.S. Interstate Highways Based on Great Circle Distance

In this study, 98 regression models were specified for easily estimating shortest distances based on great circle distances along the U.S. interstate highways nationwide and for each of the continental 48 states. This allows transportation professionals to quickly generate distance, or even distance matrix, without expending significant efforts on complicated shortest path calculations. For simple usage by all professionals, all models are present in the simple linear regression form. Only one explanatory variable, the great circle distance, is considered to calculate the route distance. For each geographic scope (i.e., the national or one of the states), two different models were considered, with and without the intercept. Based on the adjusted R-squared, it was observed that models without intercepts generally have better fitness. Additionally, all these models generally have good fitness with the linear regression relationship between the great circle distance and route distance. At the state level, significant variations in the slope coefficients between the state-level models were also observed. Furthermore, a preliminary analysis of the effect of highway density on this variation was conducted.

33 ADVANCED PROPULSION SYSTEMS↗

NGEE Arctic Integrated Modeling (IM2): Improved subgrid hillslope hydrologic connectivity

This data product represents the integration of new code capability for arctic tundra hillslope hydrologic processes into the Energy Exascale Earth System Model (E3SM), through the E3SM Land Model (ELM) component. This code integration is the result of collaborative effort between the NGEE Arctic project and the E3SM project. The current ELM represents water movement primarily through vertical processes, such as precipitation, canopy interception, evaporation, infiltration, and soil water movement. Lateral water movement—such as surface runoff, subsurface flow, and river transport—plays a significant role in the hydrological cycle, especially in regions with varied topography. While E3SM includes a runoff routing component representing water transport in the river network, the lateral transport of water at the subgrid scale within the land model has previously not been taken into account. With the recent development of topographic units within the ELM subgrid data structure, there is an opportunity to simulate hillslope hydrologic connectivity by introducing water transport along topographic gradients. We expect that more realistic representation of hillslope hydrologic processes will lead to improved predictions of both soil water content and river network flows. Lateral transport of water at and near the surface is represented as a sub-grid process in this new code development. Water is tracked as it moves from higher to lower elevations within a gridcell. This capability uses the nested hierarchical sub-grid scheme within ELM to connect water fluxes from sub-grid elements with higher elevation to those with lower elevation. This data record consists of a single document (pdf format) that describes the theoretical basis for the hillslope hydrology processes added to ELM, and describes the modifications made to the ELM code. The Methods section of this metadata record includes a link to the public E3SM code repository where the exact code modifications as integrated in E3SM can be accessed. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

Thornton, Peter E [ORNL] (ORCID:0000000247595158)↗

Meteoric 10Be Flux Calibration Data for the East River Watershed, Colorado, USA

This data package contains tabular and geospatial data used to quantify and model meteoric beryllium-10 fluxes in the East River watershed, Colorado, USA. The tabular component includes calibration-site data from five glacial moraine sites and includes environmental variables used to evaluate spatial controls on meteoric 10Be delivery, including elevation, mean annual precipitation (MAP), mean snow depth, and mean snow water equivalent (SWE). These site-level data were used to compare observed fluxes with environmental gradients across the watershed and to evaluate the effects of erosion correction on flux estimates. The package also includes supporting slope and curvature values used to assess topographic inputs to the erosion analysis. A second component of the data package contains updated manuscript tables and regression outputs used to summarize the relationships between meteoric 10Be flux and environmental predictors. These tables include meteoric 10Be sample information and AMS results, site-level environmental values, site-level meteoric 10Be inventory and flux values, watershed-averaged predicted fluxes, soil bulk density measurements, fine-fraction values, soil pH measurements, and regression statistics including slope, intercept, coefficient of determination, and p-value. The regression products include both standard linear regressions and regressions in which the intercept is constrained to pass through zero, and they support the analyses presented in the companion manuscript. Together, these tabular files provide the numerical basis for the manuscript tables and the regression-based interpretation of meteoric 10Be flux variability in a snow-dominated mountain watershed. The geospatial component of the package consists of GeoTIFF raster files used to generate the map products presented in Figures 2 and 6 of the companion manuscript. These rasters represent watershed-scale spatial layers for environmental variables and regression-based predictions of meteoric 10Be flux. This dataset contains comma-separated values files (.csv), Microsoft Excel files (.xlsx), GeoTIFF raster files (.tif), and upporting metadata files, including CSV data dictionaries and readme text files (.csv, .txt). The tabular files can be opened with standard spreadsheet software, and the raster files can be viewed and analyzed in GIS software such as ArcGIS Pro or QGIS. Together, these files document the numerical and spatial datasets used to calibrate and predict meteoric 10Be delivery in the East River watershed.

East River↗

Monte Carlo simulation analysis for radiation damage on Glidcop Al-15 caused by 17-20 MeV/u heavy ions

The Facility for Rare Isotope Beams (FRIB) SRF linear heavy-ion accelerator is designed to accelerate all ions up to uranium to a maximum beam power of 400 kW. Several beam intercepting devices (BIDs) are essential to the successful operation of the accelerator, including a low power charge selector (LPCS) made of copper containing 0.15% precipitated aluminum oxide by weight called Glidcop Al-15. As FRIB ramps up the primary beam power beyond the current 20 kW level, the charge selector must withstand higher radiation damage rates, typically measured in displacements per atom (dpa). Significant beam induced radiation damage including significant deformation, like swelling, blistering, and cracking has been observed on a recently removed LPCS. We also observed physical features up to about 5.5 mm wide and appear to be deeper than the projected range of any ions. This paper presents the results of Monte Carlo simulations carried out using the Particle and Heavy Ion Transport code System (PHITS), quantifying the total damage dose and ion concentration, etc. Simulating an accurate irradiation history is essential to determining the scope of post irradiation examination (PIE) work.

Fletcher, Ethan [Michigan State U.]↗

Beam Diagnostic Challenges for FACET-II

FACET-II, the Facility for Advanced Accelerator Experimental Tests II, is a new accelerator R&D test facility to be constructed at SLAC. It will provide high-energy, high-density electron and positron beams to advance the development of beam driven plasma wakefield acceleration and support a broad range of experiments. The FACET-II beams are expected to have 10 GeV energy, contain 2 nC of charge, have a transverse normalized emittance of 7 microns, be compressed to about 1 micron long and focused to about 6 micron wide at the interaction point. Additionally, the nominal peak current is 20 kA and is expected to fluctuate up to 200 kA. Most experiments desire complete knowledge of the incoming beam parameters on a pulse-to-pulse basis. However, the extreme beam densities and strong fields of the beam current will destroy any diagnostics intercepting the beam in a single shot and impose unique challenges for beam diagnostics. Moreover, non-intercepting diagnostics are desirable to provide feedback for machine setup and characterization. Finally, we need to look beyond conventional diagnostics to seek new solutions for measurements of the high charge, small beam size, short bunch length, and low emittance.

43 PARTICLE ACCELERATORS↗

Hierarchical Linear Regression (Rev. 1)

We describe an algorithm for making inferences in a hierarchical linear model. The model allows different slopes and intercepts for different groups, and ties together the different slopes by representing them as samples from a higher level distribution. (The intercepts are treated as statistically independent.) Our model and code permit many options for the variance of this hierarchical distribution for the slopes, including gamma distributions on the precision, t-distributions on the standard error, pooled slopes (all equal), and independent slopes. The algorithm is described in the paper; an implementation of the algorithm in R is available on request.

97 MATHEMATICS AND COMPUTING↗

Thermal / structural analysis of the HB 650 thermal shield

Fermilab’s PIP-II project’s superconducting linear accelerator will drive the next generation of particle accelerators through a revolution in beam intensity. Key to beam intensification are the high efficiencies of niobium-tin superconducting radiofrequency (SRF) cavities operating at cryogenic temperatures near 5 Kelvin. A multifaceted approach is employed to achieve and maintain the extreme temperature. Vacuum provides the first barrier to thermal convection. Physical thermal intercept zones further isolate the exterior shell vacuum vessel at 300 Kelvin from the supercooled beamline. The first thermal intercept lies just inside the exterior vacuum vessel forming the 40 Kelvin zone. This 40K thermal shield is the focus of this investigation. In preparation for operation, the thermal shield is cooled from 300K to 40K in a slow process over 2-1/2 days. The factors limiting the cooling rate are a high thermal gradient which produces thermal strain and high mechanical stress. D ecreasing the time required to reach operational temperatures is the desired research goal. Physical testing data and finite element method (FEM) computer models from the Single Spoke Resonator – 1 (SSR1) and Linac Coherent Light Source (LCLS-II) cryomodules will be evaluated to determine needed design changes. The thermal shield design for the High Beta 650 MHz (HB650) will be modified and analyzed using FEM computer models to determine maximum cooling rate with a target of 50 thermal cycles of life. Maximum allowable stress will be determined through low cycle fatigue calculations.

43 PARTICLE ACCELERATORS↗

Materials Characterization, Prediction, and Control Project: Characterization of 316L Stainless Steel after Solid Phase Processing using Ultrasonic NDE Method

The Pacific Northwest National Laboratory undertook the Materials Characterization, Prediction, and Control Laboratory Directed Research and Development Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems produced via advanced manufacturing methods, such as solid phase processing, for use in national security and advanced energy applications (Smith 2021). A motivation of the Materials Characterization, Prediction, and Control Project was to demonstrate ultrasonic testing as a nondestructive evaluation method to complement traditional destructive methods for characterizing material microstructure with emphasis on grain size determination using a method that may have future applications for real-time inline process monitoring. The objective of the work described in this report is to establish the process and an analysis method for measuring grain sizes of polycrystalline metals with ultrafine grains using ultrasonic shear wave backscattering, building on prior studies on coarser-grained material. The work involves five tasks: Measured ultrasonic backscattering experimentally for a series of 316L stainless steel specimens with various grain sizes made by friction stir processing. Calculated ultrasonic backscattering coefficients from experimental data based on a physical measurement model. Measured ground truth grain sizes of the specimens from electron backscatter diffraction grain boundary images using a generalization of the ASTM E112 (ASTM 2021) intercept method. Built a curve of ultrasonic backscattering coefficients versus the ground truth intercept-based grain sizes to determine the correlation between mean grain sizes and ultrasonic measurements. Demonstrated the ability of using the correlation curve to deduce grain sizes with measured ultrasonic backscattering coefficients for a few 316L stainless steel specimens whose grain sizes were unknown beforehand but were targeted to be an extrapolation to larger grain sizes than used to formulate the correlation curves. Experimental procedures and computational algorithms are developed and validated for these tasks. This work establishes an ultrasonic technique for characterizing material microstructure with ultrafine grains that are often resulted by solid-phase processing. The technique is nondestructive, and it has the potential to be used for real time inline process monitoring. This work successfully demonstrates the viability of an ultrasonic nondestructive evaluation method for microstructural characterization of material having ultrafine grain structure (as small as 1?mm) and produced by an advanced manufacturing method. This includes a demonstration of the method to extrapolate to other conditions. While not demonstrated here, the method is expected to be viable for in-line, or near-inline, process monitoring in advanced manufacturing applications with suitable consideration for access of instrumentation to the material being manufactured.

316 L Stainless Steel↗

High-Power Targetry R&D Roadmap for High Energy Physics

Designing a reliable target is already a challenge for MW-class facilities today and has led several major accelerator facilities to operate at lower power due to target concerns. With present plans to increase beam power for next-generation accelerator facilities in the next decade, timely R&D in support of robust high-power targets is critical to secure the full physics benefits of ambitious accelerator power upgrades. The next generation of high-power targets and beam-intercepting devices (beam dumps, absorbers, collimators ) will have more complex geometries, novel materials, and new concepts that allow for use of improved high-heat-flux cooling methods. Advanced numerical simulations need to be developed to support design of reliable high-power beam targets. In parallel, development of radiation-hardened beam instrumentation is needed. Irradiation methods for high-power targets must be further developed, and new irradiation facilities are needed since only a few facilities worldwide offer beams suitable for target testing. A comprehensive R&D program must be implemented to address the many complex challenges faced by multi-MW beam intercepting devices.

Pellemoine, Frederique [Fermilab]↗

High power targets: Challenges of next-generation high-intensity neutrino beams

High power target systems are crucial elements in enabling future neutrino and other rare particle beams. These systems transform intense source of protons into secondary particles of interest to enable new scientific discoveries. As primary beam intensities increase in next-generation multi-megawatt accelerator facilities, high power target systems face key challenges. Thermal shock and radiation damage effects in beam-intercepting devices were identified as the leading cross-cutting challenges of high-power target facilities. Target materials R&D to address these challenges are therefore essential to enable and ensure reliable operation of future accelerator target facilities. This paper provides an overview of the R&D activities underway to help support high power target systems development for next-generation multi-MW facilities.

43 PARTICLE ACCELERATORS↗

Predicting Water Cycle Characteristics from Percolation Theory and Observational Data

The fate of water and water-soluble toxic wastes in the subsurface is of high importance for many scientific and practical applications. Although solute transport is proportional to water flow rates, theoretical and experimental studies show that heavy-tailed (power-law) solute transport distribution can cause chemical transport retardation, prolonging clean-up time-scales greatly. However, no consensus exists as to the physical basis of such transport laws. In percolation theory, the scaling behavior of such transport rarely relates to specific medium characteristics, but strongly to the dimensionality of the connectivity of the flow paths (for example, two- or three-dimensional, as in fractured-porous media or heterogeneous sediments), as well as to the saturation characteristics (i.e., wetting, drying, and entrapped air). In accordance with the proposed relevance of percolation models of solute transport to environmental clean-up, these predictions also prove relevant to transport-limited chemical weathering and soil formation, where the heavy-tailed distributions slow chemical weathering over time. The predictions of percolation theory have been tested in laboratory and field experiments on reactive solute transport, chemical weathering, and soil formation and found accurate. Recently, this theoretical framework has also been applied to the water partitioning at the Earth’s surface between evapotranspiration, ET, and run-off, Q, known as the water balance. A well-known phenomenological model by Budyko addressed the relationship between the ratio of the actual evapotranspiration (ET) and precipitation, ET/P, versus the aridity index, ET 0 /P, with P being the precipitation and ET 0 being the potential evapotranspiration. Existing work was able to predict the global fractions of P represented by Q and ET through an optimization of plant productivity, in which downward water fluxes affect soil depth, and upward fluxes plant growth. In the present work, based likewise on the concepts of percolation theory, we extend Budyko’s model, and address the partitioning of run-off Q into its surface and subsurface components, as well as the contribution of interception to ET. Using various published data sources on the magnitudes of interception and information regarding the partitioning of Q, we address the variability in ET resulting from these processes. The global success of this prediction demonstrated here provides additional support for the universal applicability of percolation theory for solute transport as well as guidance in predicting the component of subsurface run-off, important for predicting natural flow rates through contaminated aquifers.

54 ENVIRONMENTAL SCIENCES↗

DYNAMICS OF CIRCUMSTELLAR DISKS. III. THE CASE OF GG Tau A

We present two-dimensional hydrodynamic simulations using the Smoothed Particle Hydrodynamic code, VINE, to model a self-gravitating binary system. We model configurations in which a circumbinary torus+disk surrounds a pair of stars in orbit around each other and a circumstellar disk surrounds each star, similar to that observed for the GG Tau A system. We assume that the disks cool as blackbodies, using rates determined independently at each location in the disk by the time dependent temperature of the photosphere there. We assume heating due to hydrodynamical processes and to radiation from the two stars, using rates approximated from a measure of the radiation intercepted by the disk at its photosphere. We simulate a suite of systems configured with semimajor axes of either a = 62 AU (“wide”) or a = 32 AU (“close”), and with assumed orbital eccentricity of either e = 0 or e = 0.3. Each simulation follows the evolution for ∼6500–7500 yr, corresponding to about three orbits of the torus around the center of mass. Our simulations show that strong, sharply defined spiral structures are generated from the stirring action of the binary and that, in some cases, these structures fragment into 1–2 massive clumps. The torus quickly fragments into several dozen such fragments in configurations in which either the binary is replaced by a single star of equal mass, or radiative heating is neglected. The spiral structures extend inwards to the circumstellar environment as large scale material streams for which most material is found on trajectories that return it to the torus on a timescale of 1–200 yr, with only a small fraction accreting into the circumstellar environment. The spiral structures also propagate outwards through the torus, generating net outwards mass flow, and eventually losing coherence at large distances from the stars. The torus becomes significantly eccentric in shape over most of its evolution. In all configurations, accretion onto the stars occurs at a steady rate of a few ×10{sup −8} M {sub ⊙} yr{sup −1}, with the net result that, without replenishment, the disk lifetimes would be shorter than ∼10{sup 4} yr. Our simulations show that only wide orbit configurations are able to retain circumstellar disks, by virtue of accretion driven from the robust material streams generated in wide configurations, which are very weak in close configurations. In wide, eccentric orbit configurations, accretion is episodic and occurs preferentially onto the secondary, with rates strongly peaked near the binary periapse. Based on our results, we conclude that the GG Tau A torus is strongly self gravitating and that a major contribution to its thermal energy input is the shock dissipation associated with spiral structures generated both by self gravitating disturbances and by the stirring action of the binary. We interpret the sharply defined features observed in the torus as manifestations of such spiral structures. We interpret the low density disk surrounding it as an excretion disk created by the outward mass flux generated by the spiral arms as they propagate outwards. Typical eccentricities calculated for the shape of the tori modeled in our simulations are large enough to account for the supposed ∼20° mutual inclination between the stellar orbit plane of GG Tau A and its surrounding torus through a degeneracy between the interpretation of inclination of the torus and its eccentricity. We therefore interpret the observations in favor of a coplanar system with an eccentric torus. Because accretion onto the disks occurs at rates sufficient to sustain them only in wide orbit configurations, we conclude that the gas currently resident in the circumstellar disks of the GG Tau A system has been accreted from the torus within the past few thousand years. Although circumstellar disks will persist over time spans long enough to permit planet formation, the overall environment remains unfavorable due to high temperatures and other conditions. Given the presence of circumstellar disks, robust accretion streams, and our interpretation of the GG Tau A stellar orbit plane as coplanar with the torus surrounding it, we conclude that the GG Tau A system is in an eccentric, a ∼ 62 AU orbit, resolving questions in the literature regarding its orbit parameters.

79 ASTRONOMY AND ASTROPHYSICS↗