Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IMPINGEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Twinning pathways enabled by precipitates in $\mathrm{AZ91}$

While precipitates have been shown to substantially strengthen magnesium alloys by blocking the glide of dislocations inside the grain, the interactions between these precipitates and deformation twins, which commonly occur in these alloys, are much less understood. Here, in this work, an elasto-viscoplastic fast-Fourier-transform (EVP-FFT) model is used to study the interactions between plate-shaped basal precipitates and propagating $10\bar{1}2$ tensile twins in AZ91 Mg alloy. The results suggest that while precipitates may impede the propagation and thickening of twins, they can also cause stress localizations that can promote the formation of multiple new twins of the same or different crystallographic variants. We show that the location of the twin-precipitate interaction site, whether precipitate-central or precipitate-edge impingement, and the thickness of the precipitate can influence the propensity for twins to expand around the precipitate or nucleate a new twin on the other side of it. Depending on the twin-precipitate impingement site, we propose multiple twinning pathways that can help explain how twins can proliferate in the magnesium alloys in the presence of precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A gas dynamic perspective on particle lifting in electrostatic discharge-like devices using multiphase particle-in-cell approach

Although particle–laden electrostatic discharges are widely used in laboratories as well as in industrial applications, the mechanism of particle lifting for particles initially at rest in such highly unsteady systems is not well understood. A multiphase gas–particle solver is developed using the multiphase particle-in-cell (MP-PIC) approach to emulate the interaction of a compressible shock-dominated gas phase with the dense particle phase. First, the two-way coupled solver is initially used to study the interaction of a planar traveling shock with a vertical curtain of particulates. The gas and particle phase evolution was found to be in good agreement with a similar experimental study in Ling et al. [Phys. Fluids 24, 113301 (2012)]. Second, the MP-PIC code is used to study the interaction of an expanding blast wave with a thick bed of particles. The simulation considered forces such as quasi-steady drag, pressure-gradient, added-mass, Saffman, and Magnus forces. We observe that the vertical liftoff particles close to the shock impingement point in this configuration are associated with the quasi-steady drag, pressure gradient, and added-mass forces. Also, the Saffman lift and Magnus forces contribute to lifting particles located radially farther away from the shock impingement point. In addition, the study finds a decrease in particle lifting efficiency with decreasing plasma kernel length and shock strength.

42 ENGINEERING↗
DOE OSTI2023

Modeling of the spray-induced wall stress acting on the ignition assistance device

This research introduces a novel wall-stress model called the Spray-Induced Wall Stress (SIWS) model, which considers the effects of spray-wall impingement and the resulting formation of wall stress within the Lagrangian spray modeling framework. The primary objective of this paper is to provide a mathematical description of the fundamental physics underlying the model. Subsequently, the proposed model is validated using existing experimental data. Here, the remainder of the study focuses on the practical application of the model to an ignition assistance device. Specifically, this device is installed in a compression ignition engine and designed to enhance ignition in aviation-fueled high-altitude aircraft propulsion systems. The research sheds light on the mechanical impulse caused by the high-speed impact of the spray jet, leading to the accumulation of mechanical stress on the rigid body of the ignition assistance device. Previous studies on fluid-structure interaction have only considered the interaction between the gas phase and the solid wall. However, the SIWS model incorporates the additional impact of the impinging liquid spray jet. Consequently, the simulated stress distribution on the ignition assistance device can be estimated by considering both the gas-phase-induced term and the spray-induced term simultaneously.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

Extended Rice–Thomson analysis and atomistic simulations revealing grain boundary effects on fracture in refractory high-entropy alloys

Significance This work serves to extend the fundamental ductile vs. brittle fracture theory, specifically the Rice–Thomson criterion, by introducing a grain boundary ahead of an initiating crack which propagates at an oblique angle to impinge the boundary. Atomistic fracture simulations on two refractory complex concentrated alloys, the brittle NbMoTaW and the ductile Nb 45 Ta 25 Ti 15 Hf 15 , demonstrate qualitative correspondence with the extended Rice–Thomson criterion and experimental observations. Abstract Understanding how grain boundaries mediate fracture remains a critical challenge in designing ductile, high-performance refractory alloys. Here, we extend the Rice–Thomson criterion to account for the angle between cracks and the impinging grain boundaries (GBs), capturing the competition between intergranular fracture and dislocation-mediated plasticity. Using machine learning interatomic potentials, we performed molecular statics simulations to probe fracture mechanisms in nanocrystalline NbMoTaW and Nb 45 Ta 25 Ti 15 Hf 15 , each with two different grain sizes, revealing trends consistent with experimental observations and the extended Rice model. Comparison with averaged R-curves for bulk samples demonstrates that GBs enhance ductility in Nb 45 Ta 25 Ti 15 Hf 15 in both grain sizes investigated. In contrast, GBs only locally improve fracture resistance in NbMoTaW when cracks are temporarily pinned at GBs inclined at high angles from the crack, but generally promote brittle intergranular fracture. These contrasting behaviors are attributed to differences in GB cohesion, reflecting clear alloying trends that align with ab-initio calculations and trends observed experimentally. Our results bridge classical fracture theory, atomistic simulations, and experimental observations, providing a comprehensive understanding of the fracture mechanisms in nanocrystalline refractory complex concentrated alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-Fidelity Simulation of the Light-to-Dense Stratification Transient in the HiRJET Facility

Density stratification in a large enclosure is a crucial phenomenon to heat transfer and sustainable passive heat removal of a sodium fast reactor during reactivity transients. However, engineering turbulence models were identified to have unsatisfactory performance in predicting propagation of a stratified front. Yet, the scarcity of high-resolution data for stratification hampers the development of models. To explor e applications of leveraging direct numerical simulation (DNS) data to support turbulence model development, this work conducted DNS using NekRS to study a long stratification transient in the High-Resolution Jet (HiRJET) experimental facility. Here, this work considers an experiment run where light fluid is injected into a tank containing a denser fluid with a relative density difference of 1.5%. Formation of the stratified layer is identified as impingement of the buoyant jet promoting mixing of the two fluids. Based on the transient statistics, transport of the concentration can be characterized by regions with dominating effects of turbulent mixing, buoyant dissipation, and molecular diffusion, respectively, as moving away from the elevation of jet impingement. Concentration near the stratified front also exhibits oscillation at Brunt-Väisälä frequency. Preliminary validation of the simulation showed encouraging agreement of the concentration distribution with the reference experiment.

buoyant mixing↗
DOE OSTI2023

Quantitative Systems Modeling for Critical Infrastructure Predictions in Climate Change: A National Defense Framework

Any national defense is dependent on the efficacy of the available physical infrastructure. Whatever degrades infrastructure, structurally, physically, architecturally, or esthetically, is of interest to the nation. Climate change is now a major significant factor of interest impinging on national critical infrastructure. The devastating effects of climate change have increasing pervasiveness throughout the world. The impact on critical infrastructure is of particular interest to researchers. In consonance with ASCE-ASME's special issue on critical infrastructure protection and resilience, this paper presents a systems-modeling approach for critical infrastructure and predictions in relation to climate change agreements in COP26. The paper addresses high-level critical systems-based assessment of the social, legal, economic, and technical nuances impinging on the viability of COP26 agreements. The paper was written using a multinational collaboration approach. In conclusion, the specific focus of national defense is used as the backdrop for the methodology of the paper.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

A new approach of microbiome monitoring in the built environment: feasibility analysis of condensation capture

Background: Humans emit approximately 30 million microbial cells per hour into their immediate vicinity. However, sampling of aerosolized microbial taxa (aerobiome) remains largely uncharacterized due to the complexity and limitations of sampling techniques, which are highly susceptible to low biomass and rapid sample degradation. Recently, there has been an interest in developing technology that collects naturally occurring water from the atmosphere, even within the built environment. Here, we analyze the feasibility of indoor aerosol condensation collection as a method to capture and analyze the aerobiome. Methods: Aerosols were collected via condensation or active impingement in a laboratory setting over the course of 8 h. Microbial DNA was extracted from collected samples and sequenced (16S rRNA) to analyze microbial diversity and community composition. Dimensional reduction and multivariate statistics were employed to identify significant (p < 0.05) differences in relative abundances of specific microbial taxa observed between the two sampling platforms. Results: Aerosol condensation capture is highly efficient with a yield greater than 95% when compared to expected values. Compared to air impingement, aerosol condensation showed no significant difference (ANOVA, p > 0.05) in microbial diversity. Among identified taxa, Streptophyta and Pseudomonadales comprised approximately 70% of the microbial community composition. Conclusion: The results suggest that condensation of atmospheric humidity is a suitable method for the capture of airborne microbial taxa reflected by microbial community similarity between devices. Future investigation of aerosol condensation may provide insight into the efficacy and viability of this new tool to investigate airborne microorganisms.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Evaluation of Polyethylene and Blank Pulsed Sphere Experiments Using Deuteron Transport Feature in COG

From the late 1960s to about 1985, LLNL undertook a series of ‘pulsed sphere’ experiments for 31 materials involving 148 different experiments using 75 different spheres. The purpose was to measure the neutron leakage spectra for different materials from 14-MeV neutrons generated by 3 H(d,n) 4 He reactions induced by an incident D+ beam from the Insulated Core Transfer (ICT) accelerator at LLNL. This deuteron beam was focused to impinge upon tritium loaded onto a titanium substrate within a low mass target assembly placed within the center of a spherical shell constructed from the material of interest. COG is a three-dimensional, continuous energy, Monte Carlo code, developed by Lawrence Livermore National Laboratory (LLNL). Recent additions to COG include alpha and deuteron particle transport in order to directly calculate (α,n) and 3 H(d,n) 4 He reactions, and resulting neutron emission spectra. Results of the direct deuteron transport calculation for the 0.8 MFP (mean free path) polyethylene sphere with PILOT B detector was previously published. The purpose of this paper is to present expanded COG results showing the neutron peak from deuterium buildup ( 2 H(d,n) 3 He) due to tritium decay in the target. Cross section data libraries used are ENDF/B-VIII.0 for neutrons and ENDF/B-VII.1 for deuterons, respectively.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Second Annual Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with the flat wall of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the resonant frequency, which can be detected with a spectrum analyzer. Because the transducer is intended for immersion in a high temperature corrosive fluid, understanding of material degradation is crucial for estimation of transducer performance lifetime, and development of measurement interpretation algorithms. We conducted a preliminary computational investigation of relevant damage mechanisms of a stainless steel 316 cylindrical resonator in FLiBe salt. The two main damage mechanisms, creep and corrosion, were modeled using multiphysics COMSOL software. Degradation was modeled for a temperature range 500°C to 700°C. Coupling of the damage mechanisms was not considered. These models predict significant inelastic deformation at most temperatures due to creep, and qualitatively predict chromium depletion both along the liquid/solid interface and along the grain boundaries. An algorithmic approach for compensation of these degradation effects during fluid flow measurements will be developed in the future work. To validate sensor physics, we have performed proof-of-principle test of flow sensing in water. For this test, we have developed a cylindrical resonator for K-band, which was machined from brass. The cavity was excited through WR-42 waveguide through a subwavelength hole on the side of the wall of the cylinder. To increase the spectral signal visibility, we developed a signal processing method for baseline subtraction. A flow loop for proof-of-principle test of transducer performance in water was assembled. A commercial flow meter was installed in the loop for reference measurements. Cylindrical cavity was excited in the TE 011 mode with resonant frequency f ≈ 17.8GHz. Frequency shift of cavity spectral response was obtained by gradually increasing water flow rate from 0 to 60gpm. Corresponding monotonic increase of resonant frequency shift by several MHz was observed. Approximate figure of merit of sensitivity to flow rate is 100KHz/GPM. In addition, we have identified an existing liquid sodium experimental setup for demonstration of flow sensing in environment similar to that of an advanced reactor. The setup consists of a cylindrical vessel and center feed line, where transducer inserted through the lid will measure velocity of the impinging liquid jet. As a calibration experiment, we have assembled a water vessel with center feed with the same dimensions as those of the liquid sodium setup. We have also developed and insertion probe consisting of a 50cm brass waveguide enclosed in protective SS316 tube. Using the water loop, we have demonstrated feasibility of sensing the impinging liquid jet in the vessel.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Development and Integration of a Stochastic Clad Damage Propagation Model into PRONGHORN-SC Subchannel Analysis Code

The failure of fuel pins in nuclear reactors is intrinsically stochastic. Typically, a combination of variation in manufacturing that affects the material characteristics and the fuel assembly dimensions, variation in operating conditions, such as local power, coolant flow rate, and irradiation induced changes in material properties lead to a large uncertainty in failure margin of the fuel pins. Failure, therefore, may occur in exceptional pins with adverse combinations of these variations. Upon a metal fuel pin (U-Pu-Zr/HT9) failure, depressurization of the fuel pin takes place by release of fission gas, liquid sodium bond, and potentially solid fuel particles or molten/eutectic fuel droplets through the hole in cladding. The effect of a fission gas jet on neighbor fuel pins and possible propagation of a clad damage during normal operation was studied experimentally in 1970s and it was found that the post-failure fission gas jet insulates the jet impingement area of the target fuel pin surface and could increase the target pin’s surface temperature by as much as 100 – 200 K during the failed pin depressurization. It was concluded that the effect should not lead to fuel pin failure propagation during normal operation. In accident scenarios of sodium and lead fast reactors such as Unprotected Loss-Of-Flow (ULOF) or Unprotected Transient Over Power (UTOP), the fuel pins can be subjected to higher clad temperatures and fuel pin pressures or fuel clad mechanical/chemical interaction where thermal creep margin becomes significantly lower compared to the normal operation conditions. Therefore, possible stochastic failure and the post-failure fission gas/fuel jet impingement could be critical in order to predict fuel pin failure propagation. Pin depressurization due to fission gas release may degrade the heat transfer by formation of a gas blanket on a neighboring pin surface, which is a local phenomenon, and by causing coolant flow deceleration and starvation, which could affect a surrounding region as well. Furthermore, the potential presence of solid fuel particles or molten fuel at the time of clad failure could boost post-failure jet induced degradation even further. The present study models the U-Pu-Zr/HT9 metal fuel pin failure and stochastic clad damage propagation by biased sampling based on a Cumulative Damage Fraction (CDF) type clad failure criterion and the normal distribution of fuel failure probability density as a function of logarithm of Cumulative Damage Fraction. In addition, the effect of post-failure fission gas jet on heat transfer degradation is modeled for the target pins. This model is called stochastic Clad Damage Propagation (CDAP). The CDAP model is now fully integrated into developmental version of PRONGHORN-SC subchannel analysis code, allowing for modeling local failures and its propagation potential. Section 2 describes the components of the CDAP models. Section 3 describes the model implementation to PRONGHORN-SC and input specifications. Section 4 describes the CDAP model validation coupled to PRONGHORN-SC.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

HPC for Optimizing Process Parameters to Control Material Evolution in Seamless Induction Hardening of Wind Turbine Main Shaft Bearings

Work proposed in this project focused on understanding the effect of martensitic transformation in the steel on the potential for cracking during seamless induction hardening (SIH) as a function of process conditions to allow the process to optimally scale up. Large-scale, three-dimensional phase-field simulations of martensitic transformation were performed using MEUMAPPS-SS (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid State) code developed at Oak Ridge National Laboratory. The simulations were guided by location-specific thermal history generated by experimental measurements of time-temperature history generated at The Timken Company. The simulations were able to capture the morphological evolution of the martensite variants in an Fe-1.0C-1.5Cr steel based on the Nishiyama-Wasserman (NW) orientation relationship. The simulations were also able to quantify the stress-state at the interface between impinging martensite variants. The simulations indicated that the magnitude of the various stress and strain components were dependent on the sizes of the impinging plates with a reduction in these quantities with reduced plate size in agreement with experimental findings. The results obtained from the simulations will be used to guide the optimization of the alloy thermal conditions to eliminate quench cracking during SIH of bearing steels.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

HPC for optimizing process parameters to control material evolution in seamless induction hardening of wind turbine main shaft bearings

Work proposed in this project focused on understanding the effect of martensitic transformation in the steel on the potential for cracking during seamless induction hardening (SIH) as a function of process conditions to allow the process to optimally scale up. Large-scale, three-dimensional phase-field simulations of martensitic transformation were performed using MEUMAPPS-SS (Microstructure Evolution Using Massively Parallel Phase-field Simulations – Solid State) code developed at Oak Ridge National Laboratory. The simulations were guided by location-specific thermal history generated by experimental measurements of time-temperature history generated at The Timken Company. The simulations were able to capture the morphological evolution of the martensite variants in an Fe-1.0C-1.5Cr steel based on the Nishiyama-Wasserman (NW) orientation relationship. The simulations were also able to quantify the stress-state at the interface between impinging martensite variants. The simulations indicated that the magnitude of the various stress and strain components were dependent on the sizes of the impinging plates with a reduction in these quantities with reduced plate size in agreement with experimental findings. The results obtained from the simulations will be used to guide the optimization of the alloy thermal conditions to eliminate quench cracking during SIH of bearing steels.

17 WIND ENERGY↗
DOE OSTI2026

HIGHER EFFICIENCY FISSION COUNTER FOR NEUTRON DETECTION

Fission chambers containing 235U have been used for detection of neutrons for many decades. In these chambers 235U is electroplated on a metal which is one plate of an ionization chamber. Since the range of fission products from induced fission in the chamber is extremely short, these deposits from electroplating are so thin that the amount of 235U results in low neutron detection efficiency and the chamber needs high internal 235U surface area to increase efficiency. A typical ~8 in. long, ~2 in. diameter fission counter only contains < 2 g of 235U total, resulting in very low detection efficiency per incident neutron impinging on the outer surface of the detector. However, because of their large electronic pulses from fission products compared to gamma rays it is very easy to discriminate against gamma rays impinging on the detector. These types of chambers are produced commercially and are used worldwide in nuclear research and nuclear power reactors. ORNL has made a higher efficiency fission ionization chamber by using many thin concentric annuli to increase the area. A higher efficiency fission counter would be useful and can be made by incorporating 235U into a glass or ceramic scintillator. For nearly 100 years the green color in antique glass was produced by incorporation of depleted uranium (up to 20 wt. %) into a glass. The concept for this scintillation-optical-based fission detector is to dope a scintillator (either ceramic or glass) with 235U. Glass scintillators are commercially available doped with as much as 8 wt. % 6Li for neutron detection. In the 235U doped scintillator the fission product pulses would be double the size of those in an ion chamber since all fission products produce light in the scintillator whereas in the ionization chamber half do not go into the ionizing gas volume. These higher efficiency fission chambers would be very useful for a wide variety of research, nuclear research, and nuclear power reactor applications. Because of their smaller size and weight, they should be useful for space application such as monitoring of space nuclear power reactors. This report reviews existing fission chamber technology and suggests the development of these small high-efficiency fission chambers. Other fission isotopes could be used for other research applications.

Mihalczo, John [ORNL] (ORCID:0000000254292681)↗
DOE OSTI2024

An Investigation of Oxides of Tantalum Produced by Pulsed Laser Ablation and Continuous Wave Laser Heating

Recent progress has seen multiple Ta 2 O 5 polymorphs generated by different synthesis techniques. However, discrepancies arise when these polymorphs are produced in widely varying thermodynamic conditions and characterized using different techniques. This work aimed to characterize and compare Ta 2 O 5 particles formed at high and low temperatures using nanosecond pulsed laser ablation (PLA) and continuous wave (CW) laser heating of a local area of tantalum in either air or an 18 O 2 atmosphere. Scanning electron microscopy (SEM) and Raman spectroscopy of the micrometer-sized particles generated by PLA were consistent with either a localized amorphous Ta 2 O 5 phase or a similar, but not identical, crystalline β-Ta 2 O 5 phase. The Raman spectrum of the material formed at the point of CW laser impingement was in good agreement with the previously established ceramic “H-Ta 2 O 5 ” phase. TEM and electron diffraction analysis of these particles indicated the phase structure matched an oxygen-vacated superstructure of monoclinic H-Ta 2 O 5 . Further from the point of laser impingement, CW heating produced particles with a Raman spectrum that matched β-Ta 2 O 5 . We confirmed that the high-temperature ceramic phase characterized in previous work by Raman spectroscopy was the same monoclinic phase characterized in different work by TEM and could be produced by direct laser heating of metal in air.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Particle Matter Index and Fuel Wall-wetting Relations on Stochastic Pre-ignition

This works explores the effect of the particle matter index (PMI) and aromatic content on fuel wall impingement and associated stochastic pre-ignition (SPI) propensity. Statically significant measurements of SPI rates are directly coupled with laser induced florescence (LIF) measurements of fuel dilution from spray-linear impingement. Literature suggests that PMI is could be correlated with the number of SPI events, but the root cause(s) of PMI and SPI are directly causational or are a predicator of SPI. Three fuels have been used in this study with 3 different PMI and two different aromatic contents. These fuels are direct injected at two different injection timings, an earlier injection timing which targets the piston crown, 310°CA bTDC, and a later injection timing that the linear, 220°CA bTDC start of injection timings (SOI) respectively. The earlier 310 SOI injection increases soot, whereas the later 220°CD SOI targets the linear and increases wall-wetting. The findings of this work highlight that the SPI activity has a weak correlation with the soot promoted by the combustion process and increased PMI. However, SPI activity shows a strong dependency with high levels of oil dilution and aromatic content, suggesting that PMI might be an indicator of fuel chemistry conducive to SPI and the soot form increased PMI fuels is not a strong source of SPI relative to fuel wall wetting.

42 ENGINEERING↗
DOE OSTI2021

System and method for passive assay of holdup deposits in nuclear piping

Disclosed herein are a method, apparatus, and software for passive, non-destructive assay of holdup deposits in nuclear piping by in-pipe apparatus. A detector deployed within a pipe is collimated to observe radiation impinging radially inward from decay of deposits that lie on the pipe wall. A radiation detector is centered in the pipe and collimated by a pair of coaxial shielding discs disposed equidistant from the detector. This arrangement causes radiation from a truncated cylinder of pipe deposit within a field of regard to impinge on the detector, while precluding radiation emanating from pipe walls beyond the field of regard from reaching the detector. Hence, observations are unique to a known cylindrical length of pipe. The detector assembly is translated through pipes by an autonomous mobile robotic apparatus. Computer software controls the robotic apparatus, logs data, and post-processes to assay deposits.

Whittaker, William Lawrence↗
DOE OSTI2022

Coolant delivery via an independent cooling circuit

An embodiment of an independent cooling circuit for selectively delivering cooling fluid to a component of a gas turbine system includes: at least one coolant feed channel fluidly coupled to a supply of cooling fluid; and an interconnected circuit of cooling channels, including: an interconnected circuit of cooling channels embedded within an exterior wall of the component; an impingement plate; and a plurality of feed tubes connecting the impingement plate to the exterior wall of the component and fluidly coupling a supply of cooling fluid to the interconnected circuit of cooling channels; wherein the cooling fluid flows through the plurality of feed tubes into the interconnected circuit of cooling channels only in response to a formation of a breach in the exterior wall of the component that exposes at least one of the cooling channels.

42 ENGINEERING↗