SEARCH · Engineering Papers

Results for “High Temperature Plasma”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS1993

INPIStron switched pulsed power for dense plasma pinches

The inverse plasma switch INPIStron was employed for 10kJ/40kV capacitor bank discharge system to produce focused dense plasmas in hypocycloidal-pinch (HCP) devices. A single unit and an array of multiple HCP's were coupled as the load of the pulsed power circuit. The geometry and switching plasma dynamics were found advantageous and convenient for commutating the large current pulse from the low impedance transmission line to the low impedance plasma load. The pulse power system with a single unit HCP, the system A, was used for production of high temperature plasma focus and its diagnostics. The radially running down plasma dynamics, revealed in image converter photographs, could be simulated by a simple snow-plow model with a correction for plasma resistivity. The system B with an array of 8-HCP units which forms a long coaxial discharge chamber was used for pumping a Ti-sapphire laser. The intense UV emission from the plasma was frequency shifted with dye-solution jacket to match the absorption band of the Ti crystal laser near 500 nm. An untuned laser pulse energy of 0.6 J/pulse was obtained for 6.4 kJ/40 kV discharge, or near 103 times of the explosion limit of conventional flash lamps. For both systems the advantages of the INPIStron were well demonstrated: a single unit is sufficient for a large current (greater than 50 kA) without increasing the system impedance, highly reliable and long life operation and implied scalability for the high power ranges above I(sub peak) = 1 MA and V(sub hold) = 100 kV.

Han, Kwang S.↗

NASA NTRS2016

Solar Array at Very High Temperatures: Ground Tests

Solar array design for any spacecraft is determined by the orbit parameters. For example, operational voltage for spacecraft in Low Earth Orbit (LEO) is limited by significant differential charging due to interactions with low temperature plasma. In order to avoid arcing in LEO, solar array is designed to generate electrical power at comparatively low voltages (below 100 V) or to operate at higher voltages with encapsulated of all suspected discharge locations. In Geosynchronous Orbit (GEO) differential charging is caused by energetic electrons that produce differential potential between coverglass and conductive spacecraft body in a kilovolt range. In such a case, weakly conductive layer over coverglass (ITO) is one of possible measures to eliminate dangerous discharges on array surface. Temperature variations for solar arrays in both orbits are measured and documented within the range of -150 C +110 C. This wide interval of operational temperatures is regularly reproduced in ground tests with radiative heating and cooling inside shroud with flowing liquid nitrogen. The requirements to solar array design and tests turn out to be more complicated when planned trajectory crosses these two orbits and goes closer to Sun. Conductive layer over coverglass causes sharp increase in parasitic current collected from LEO plasma, high temperature may cause cracks in encapsulating material (RTV), radiative heating of coupon in vacuum chamber becomes practically impossible above 150 C, conductivities of glass and adhesive go up with temperature that decrease array efficiency, and mechanical stresses grow up to critical magnitudes. A few test arrangements and respective results are presented in current paper. Coupons were tested against arcing in simulated LEO and GEO environments under elevated temperatures up to 200 C. The dependence of leakage current on temperature was measured, and electrostatic cleanness was verified for coupons with antireflection (AR) coating over ITO layer.

differential charging↗

NASA NTRS2016

Solar Array at Very High Temperatures: Ground Tests

Solar array design for any spacecraft is determined by the orbit parameters. For example, operational voltage for spacecraft in Low Earth Orbit (LEO) is limited by significant differential charging due to interactions with low temperature plasma. In order to avoid arcing in LEO, solar array is designed to generate electrical power at comparatively low voltages (below 100 volts) or to operate at higher voltages with encapsulation of all suspected discharge locations. In Geosynchronous Orbit (GEO) differential charging is caused by energetic electrons that produce differential potential between the coverglass and the conductive spacecraft body in a kilovolt range. In such a case, the weakly conductive layer over coverglass, indium tin oxide (ITO) is one of the possible measures to eliminate dangerous discharges on array surface. Temperature variations for solar arrays in both orbits are measured and documented within the range of minus150 degrees Centigrade to plus 1100 degrees Centigrade. This wide interval of operational temperatures is regularly reproduced in ground tests with radiative heating and cooling inside a shroud with flowing liquid nitrogen. The requirements to solar array design and tests turn out to be more complicated when planned trajectory crosses these two orbits and goes closer to the Sun. The conductive layer over coverglass causes a sharp increase in parasitic current collected from LEO plasma, high temperature may cause cracks in encapsulating (Room Temperature Vulcanizing (RTV) material; radiative heating of a coupon in vacuum chamber becomes practically impossible above 1500 degrees Centigrade; conductivities of glass and adhesive go up with temperature that decrease array efficiency; and mechanical stresses grow up to critical magnitudes. A few test arrangements and respective results are presented in current paper. Coupons were tested against arcing in simulated LEO and GEO environments under elevated temperatures up to 2000 degrees Centigrade. The dependence of leakage current on temperature was measured, and electrostatic cleanness was verified for coupons with antireflection (AR) coating over the indium tin oxide (ITO) layer.

differential charging↗

DOE OSTI2019

A study of velocity, temperature, and density in the plasma generated by laser-induced breakdowns

The paper presents velocity measurements of shock-induced flow field, leading to vortex generation and plasma deformation in air. Femtosecond-laser electronic excitation tagging (FLEET) velocimetry was performed at the times Δt = 3, 20, 50, and 100 µs post laser-induced breakdown. Emissions over Δt = 3–10 µs showed the propagations of the initially elliptic shock, transitioning into a spherical front. The shock emanated along the laser axis causes the flow outward, and then the pressure gradient generated by the rarefaction wave drives the inward flow at later moments, with the velocity magnitude approaching a steady-state value of 40 m s -1 . Temporal velocity evolution was compared with non-self-similar solutions behind the propagating shock, which are sensitive to the size of the energy deposition, and the use of the measured initial plasma diameter reproduced the experiment. There establishes a region of uniform velocity around 35 m s -1 in the air-flow running through the plasma, which triggers the roll-up of the plasma surface by a large-scale vortex, providing the detail of flow field evolution from the shock propagation to the plasma deformation. A collective Thomson scattering and hybrid fs/ps pure rotational coherent anti-Stokes Raman scattering (CARS) were also performed to gain insight into the high-temperature plasma. An effective electron–ion recombination rate of 2 x 10 -12 cm 3 s -1 was measured at Δt = 0.5–10 µs, during a dynamic plasma expansion and compression. When the shock resides close to the plasma at Δt = 0.5–1 µs, the temperature distributions were found to follow the similarity law.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Breaking Beams: A Kinetic Treatment of the Filamentation and Forward Scatter of Laser Beams in Plasma (Abbreviated Final Report)

Precise and predictable propagation and deposition of laser energy in high energy density (HED) plasma is threatened by the breakup of the beam into filaments. Such filaments can be deflected and sprayed but also locally intensify the light, increasing the likelihood of other problematic interactions with the plasma. Adequately modeling, anticipating, and avoiding such processes in HED experiments requires a thorough understanding of the thresholds and nonlinear saturation mechanisms, particularly for the weakly collisional, high temperature plasmas achieved at the National Ignition Facility (NIF).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Breaking Beams: A Kinetic Treatment of the Filamentation and Forward Scatter of Laser Beams in Plasma

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Final Technical Report for DoE award DE‐SC0023367 “Energetic Electron Transport in Magnetized Plasma with Magnetic Islands”

This project investigated how plasmas interact with energetic particles and solid materials under extreme conditions relevant to fusion energy, space plasmas, and planetary environments. Using experiments on the DIII-D National Fusion Facility, the research first examined how high-energy electrons move, become trapped, and are released in plasmas containing magnetic islands—structures commonly found in fusion reactors and Earth’s magnetosphere—providing new insight into particle transport and acceleration processes. The project also explored plasma-driven chemical reactions that can occur during meteoroid entry into planetary atmospheres, demonstrating that simple molecules such as ammonia can be produced and survive in high-temperature plasma conditions. Together, these results improve understanding of plasma behavior across laboratory, space, and planetary systems while informing fusion plasma control and plasma–material interaction studies. The project additionally contributed to workforce development by training graduate students, undergraduates, and early-career researchers and by disseminating results through peer-reviewed publications and international scientific conferences.

Orlov, Dmitri Mikhailovich [UC San Diego] (ORCID:0↗

NASA NTRS1985

Spectra of simulated lightning on Venus, Jupiter, and Titan

Laser-induced plasmas in various gas mixtures were used to simulate lightning in other planetary atmospheres. This method of simulation has the advantage of producing short-duration, high-temperature plasmas free from electrode contamination. The laser-induced plasma discharges in air are shown to accurately simulate terrestrial lightning and can be expected to simulate lightning spectra in other planetary atmospheres. Spectra from 240 to 880 nm are presented for simulated lightning in the atmospheres of Venus, earth, Jupiter, and Titan. The spectra of lightning on the other giant planets are expected to be similar to that of Jupiter because the atmospheres of these planets are composed mainly of hydrogen and helium. The spectra of Venus and Titan show substantial amounts of radiation due to the presence of carbon atoms and ions and show CN Violet radiation. Although small amounts of CH4 and NH3 are present in the Jovian atmosphere, only emission from hydrogen and helium is observed. Most differences in the spectra can be understood in terms of the elemental ratios of the gas mixtures. Consequently, observations of the spectra of lightning on other planets should provide in situ estimates of the atmospheric and aerosol composition in the cloud layers in which lightning is occurring. In particular, the detection of inert gases such as helium should be possible and the relative abundance of these gases compared to major constituents might be determined.

Borucki, W. J.↗

NASA NTRS1984

A solar spectral line list between 10 and 200 A modified for application to high spectral resolution X-ray astronomy

A spectral line list for the 10-200 A range is developed from existing solar spectra for application to high spectral resolution measurements of astrophysical plasmas. The solar spectral line lists are merged into a single comprehensive list. The effect of the solar emission measure distribution is removed from the line intensities, which results in a set of emission rates for the lines that can be applied to many optically thin, low density high temperature plasmas in ionization equilibrium. In addition to the measured solar lines, 250 theoretical lines are added to this list. These lines fall in wavelength regions where the existing solar lists have few lines because of limitations in instrumental sensitivity. Also, some lines have been added because the sun has very little plasma at temperatures of about one million K, and consequently these lines are weak or absent in solar spectra. The entire list contains about 600 lines. Finally, predicted spectra of the two RS CVn stars, alpha Aur (Capella) and UX Ari, are presented at 1 and 0.25 A spectral resolution. Also, the solar spectrum is shown at 1 A resolution, and the emission rate spectrum (spectrum not modified by an emission measure distribution) is shown at very high spectral resolution. The predicted spectra for Capella and UX Ari are based on results obtained from the Einstein and International Ultraviolet Explorer (IUE) spacecraft.

Doschek, G. A.↗

NASA NTRS2003

Magnetized Target Fusion Propulsion: Plasma Injectors for MTF Guns

To achieve increased payload size and decreased trip time for interplanetary travel, a low mass, high specific impulse, high thrust propulsion system is required. This suggests the need for research into fusion as a source of power and high temperature plasma. The plasma would be deflected by magnetic fields to provide thrust. Magnetized Target Fusion (MTF) research consists of several related investigations into these topics. These include the orientation and timing of the plasma guns and the convergence and interface development of the "pusher" plasma. Computer simulations of the gun as it relates to plasma initiation and repeatability are under investigation. One of the items under development is the plasma injector. This is a surface breakdown driven plasma generator designed to function at very low pressures. The performance, operating conditions and limitations of these injectors need to be determined.

Griffin, Steven T.↗

NASA NTRS2016

NuSTAR Hard X-Ray Survey of the Galactic Center Region. II. X-Ray Point Sources

We present the first survey results of hard X-ray point sources in the Galactic Center (GC) region by NuSTAR. We have discovered 70 hard (3-79 keV) X-ray point sources in a 0.6 deg(sup 2) region around SgrA* with a total exposure of 1.7 Ms, and 7 sources in the Sgr B2 field with 300 ks. We identify clear Chandra counterparts for 58 NuSTAR sources and assign candidate counterparts for the remaining 19. The NuSTAR survey reaches X-ray luminosities of approx. 4× and approx. 8 ×10(exp 32) erg/s at the GC (8 kpc) in the 3-10 and 10-40 keV bands, respectively. The source list includes three persistent luminous X-ray binaries (XBs) and the likely run-away pulsar called the Cannonball. New source-detection significance maps reveal a cluster of hard (>10 keV) X-ray sources near the Sgr A diffuse complex with no clear soft X-ray counterparts. The severe extinction observed in the Chandra spectra indicates that all the NuSTAR sources are in the central bulge or are of extragalactic origin. Spectral analysis of relatively bright NuSTAR sources suggests that magnetic cataclysmic variables constitute a large fraction (>40%-60%). Both spectral analysis and logN-logS distributions of the NuSTAR sources indicate that the X-ray spectra of the NuSTAR sources should have kT > 20 keV on average for a single temperature thermal plasma model or an average photon index of Lambda = 1.5-2 for a power-law model. These findings suggest that the GC X-ray source population may contain a larger fraction of XBs with high plasma temperatures than the field population.

center - X-rays: binaries - diffuse background↗

NASA NTRS1997

Coordinated XTE/EUVE Observations of Algol

We performed a coordinated RXTE observation of the prototypical eclipsing binary Algol in conjunction with EUVE and ASCA observations. Observing the x-ray spectrum of Algol with ASCA, EUVE, and RXTE provides critical, near-simultaneous constraints on the distribution of the hottest temperature plasma in the Agol system: this is required to unambiguously determine the coronal Fe abundance. After some initial shuffling of observatory schedules with the help of mission planners, the coordinated multiwavelength observation was successfully performed in February, 1996. Analysis of the data, including development of new, IDL-based global model fitting routines, was accomplished from mid-1996 to mid-1997. The results indicate that the initial estimates of [Fe/H] approximately 0.3 dex (Stern et al.) are confirmed, and the Algol high temperature plasma thus has an Fe deficiency relative to the (Anders and Grevesse) solar abundance.

Stern, Robert A.↗

DOE OSTI2020

Model for the electrical conductivity in dense plasma mixtures

A new density functional theory, average atom based model for the electrical conductivity of dense plasmas with a mixture of ion species, containing no adjustable parameters, is presented herein. The model takes the temperature, mass density and relative abundances of the species as input. It takes into account partial ionization, ionic structure, and core-valence orthogonality, and uses quantum mechanical calculations of cross sections. Comparison to an existing high fidelity but computationally expensive method reveals good agreement. The new model is computationally efficient and can reach high temperatures. A new mixing rule is also presented that gives reasonably accurate conductivities for high temperature plasma mixtures.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2008

A Hot Microflare Observed with RHESSI and HINODE

RHESSI and Hinode observations of a GOES B-class flare are combined to investigate the origin of 15 MK plasma. The absence of any detectable hard X-ray emission coupled with weak blueshifted emission lines (indicating upward velocities averaging only 14 km/s) suggests that this was a result of direct heating in the corona, as opposed to nonthermal electron precipitation causing chromospheric evaporation. These findings are in agreement with a recent hydrodynamical simulation of microflare plasmas that found that higher temperatures can be attained when less energy is used to accelerate electrons out of the thermal distribution. In addition, unusual redshifts in the 2 MK Fe xv line (indicating downward velocities of approx.14 km/s) were observed cospatial with one of the flare ribbons during the event. Downflows of such high-temperature plasma are not predicted by any common flare model.

Milligan, Ryan O.↗

DOE OSTI2020

Studies of Autoionizing States relevant to Dielectronic Recombinaton

Doubly excited autoionizing states of alkaline earth atoms are explored by multistep laser spectroscopy, which is precisely the inverse process to dielectronic recombination, the recombination of hot electron with ions via an autoionizing state. Dielectronic recombination is an important mechanism leading to power loss in high temperature plasmas. Measurements included the autoionization rates of atoms in zero field and in the presence of electric and magnetic fields, as might be encountered in a plasma. To mimic the effects of the rapidly varying fields of electron collisions measurements were made in the presence of microwave electric fields. These experiments are analogous to experiments conducted with combined high intensity infrared and vuv laser fields, In laser/microwave experiments the effects of laser pulse envelope timing relative to the microwave phase were explored extensively.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1976

Investigation of forbidden transitions in argon ions

An attempt has been made to observe the visible forbidden argon coronal lines at 553.6 nm (Ar X), 691.7 nm (Ar XI), 847.6 nm (Ar XIII), and 441.2 nm (Ar XIV) in a deuterium-argon plasma produced in a large theta pinch. The electron temperature (250 eV) and the electron density (5 by 10 to the 16th power per cu cm) were measured by Thomson scattering of ruby laser radiation. This temperature is adequate to produce ionization stages up to Ar XIV, as was verified by photographic observation of Ar XIV lines. No line corresponding to the coronal lines was observed from the high-temperature plasma, but lines with wavelengths very nearly identical to those of two of the forbidden transitions were observed; these lines were due to allowed transitions of Ar II in a cooler portion of the plasma. Calculation of rate coefficients in the Coulomb-Born approximation shows that for laboratory experiments, electron collisions are much more important than radiative decay in depopulating the upper state of the forbidden lines.

Jalufka, N. W.↗

DOE OSTI2025

X-ray spectroscopy of multi-temperature plasmas using the differential emission measure formalism

We present a theoretical construct that nominally underlies spectroscopic data analysis of multi-temperature plasmas, known as the differential emission measure (DEM). From a data analytic perspective, the DEM formalism is used to derive temperature distributions from line spectra that are formed in the presence of temperature gradients and by time integrations of evolving plasmas. From a modeling perspective, DEMs are convenient intermediaries between radiation hydrodynamics simulations and spectroscopic measurements acquired in the laboratory. The DEM concept and its associated methodologies were originally developed by spectroscopists working with astrophysical data. We borrow from these earlier investigations. In this manuscript, intended primarily as a tutorial, we discuss the basic concepts, but also augment various aspects of the theory by the way of extension and example, including a detailed treatment of various weighting and averaging schemes, intended to mitigate ambiguities that often arise when reporting temperature information. We focus on high-temperature plasmas that are not in local thermodynamic equilibrium and the x-ray spectra that they produce, although the core ideas presented here are applicable to spectroscopy in other energy bands. A few examples involving the derivation and manipulation of model DEMs in simple geometries are provided.

Liedahl, Duane A. [Lawrence Livermore National Lab↗

NASA NTRS2016

Correlation of Coronal Plasma Properties and Solar Magnetic Field in a Decaying Active Region

We present the analysis of a decaying active region observed by the EUV Imaging Spectrometer on Hinode during 2009 December 7-11. We investigated the temporal evolution of its structure exhibited by plasma at temperatures from 300,000 to 2.8 million degrees, and derived the electron density, differential emission measure, effective electron temperature, and elemental abundance ratios of Si/S and Fe/S (as a measure of the First Ionization Potential (FIP) Effect). We compared these coronal properties to the temporal evolution of the photospheric magnetic field strength obtained from the Solar and Heliospheric Observatory Michelson Doppler Imager magnetograms. We find that, while these coronal properties all decreased with time during this decay phase, the largest change was at plasma above 1.5 million degrees. The photospheric magnetic field strength also decreased with time but mainly for field strengths lower than about 70 Gauss. The effective electron temperature and the FIP bias seem to reach a basal state (at 1.5 x 10(exp 6) K and 1.5, respectively) into the quiet Sun when the mean photospheric magnetic field (excluding all areas <10 G) weakened to below 35 G, while the electron density continued to decrease with the weakening field. These physical properties are all positively correlated with each other and the correlation is the strongest in the high-temperature plasma. Such correlation properties should be considered in the quest for our understanding of how the corona is heated. The variations in the elemental abundance should especially be considered together with the electron temperature and density.

Sun: abundances↗