Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Heat Index”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Numerical Analysis of Fuel Effects on Advanced Compression Ignition Using a Cooperative Fuel Research Engine Computational Fluid Dynamics Model

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intake charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

High Field Side Launch of Lower Hybrid Waves: A Scoping Study for ADX

Launching lower hybrid (LH) waves from the high field side (HFS) of a tokamak offers significant advantages over low field side (LFS) launch with respect to both wave physics and plasma material interactions (PMI). The higher magnetic field opens the window between wave accessibility and the condition for strong electron Landau damping, allowing LH waves from the HFS to penetrate into the core of a burning plasma, while waves launched from the LFS are restricted to the periphery of the plasma. The lower parallel refractive index (n) of waves launched from the HFS yields a higher current drive efficiency as well. The absence of turbulent heat and particle fluxes on the HFS, particularly in double null configuration, makes it the ideal location to minimize PMI damage to the antenna structure. The quiescent SOL also eliminates the need to couple LH waves across a long distance to the separatrix, as the antenna can be located close to plasma without risking damage to the structure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Data for Responsiveness of Miscanthus and Switchgrass Yields to Stand Age and Nitrogen Fertilization: A Meta-regression Analysis

The compiled datasets include plot level observations of energy crops (miscanthus and switchgrass) from recent experimental field trials in the US including dry biomass yield, location, state, region, harvest year, growing season degree days (GDD), winter season heating degree days (HDD), growing season cumulative precipitation, annual nitrogen application rate, age of the pant when harvested, National Commodity Crop Productivity Index (NCCPI) values, and cultivar type (switchgrass) from various published and unpublished sources. The stata codes include estimation procedures for four different specifications, i.e., Model A includes deterministic effect without interaction terms; Model B includes deterministic effect with interaction terms (N2, age2, N × age, GDD2, precip2, N × NCCPI); Model C includes deterministic effect with interaction terms, study, and location random effect; Model D includes deterministic effect with interaction terms, harvest year augmented study, and location random effect.

Age↗
DOE OSTI2026

Monolithic Mesoporous Metamaterials for R-10 to R-15 Glazing (Final Scientific Technical Report)

The objective of the project was to develop and validate monolithic mesoporous metamaterials (MMMs), to which we also refer as Mesoporous Optically Clear Heat Insulators (MOCHIs) capable of serving as High-thermal-barrier Glazing (including Windows, Skylights, and Daylighting) with Transparency ≥99%, Color Rendering Index ≥99%, Haze ≤1%, Thermal Insulation per inch ≥R-15, Manufacturing Cost per Square Foot ≤$0.3; In addition, MMM-Based Frame Insulation and Glazing Products with Thermal Insulation per inch R-10 to R-15. All objectives of the project were successfully accomplished.

14 SOLAR ENERGY↗
DOE OSTI2020

Nanostructured layer for graded index freeform optics

The present disclosure relates to a method for creating an optical component having a spatially controlled refractive index. The method may involve applying a thin metal material layer to a substrate. The thin metal material layer may then be heated to create a mask having a spatially varying nano-particle distribution. The substrate may then be etched, using the mask, to imprint a spatially patterned nanostructure pattern on a surface the substrate.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Photoinduced modification of optical properties of ferroelectric PZT thin films

This study investigates ultrafast photoinduced changes in optical properties of ferroelectrics (PZT) on femtosecond to nanosecond timescales, using broadband transient reflectivity studies. Surprisingly, spectral features were observed below the bandgap, which could not be attributed to ground state bleaching, excited state absorption, and/or stimulated emission. A model based on probe energy independent changes in refractive index and extinction coefficient showed good agreement with experimental results. Three relaxation processes were phenomenologically considered for the temporal evolution. Laser-induced heating was ruled out as the cause of short timescale behavior and photorefractive effect was suggested as a potential mechanism for changes in the optical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Temperature dependent index of refraction compensation and radiation resistance in monolithic optical systems

Monolithic catadioptric optical systems are susceptible to defocus errors caused by inhomogeneous temperature within the glass material due to temperature dependent index of refraction. This invention discloses methods to mitigate these errors using tuned materials in its optical design coupled with active optical radiative heating to provide optimal performance and includes methods to enhance radiation resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Enhanced predictability of Eastern North Pacific Tropical cyclone activity using the ENSO Longitude Index

Past studies have indicated that El Nino-Southern Oscillation (ENSO) plays a major role in the interannual variability of Eastern Pacific hurricane activity. The primary mechanism being the eastward displacement of the warm pool during an El Nino, which carries warm water into that basin thereby creating favorable oceanic conditions. Despite this, the question of whether an accurate knowledge of ENSO enhances seasonal predictabiity of Eastern Pacific hurricanes has not been addressed specifically. In this study, we show that unlike traditional indices of ENSO, the ENSO Longitude Index (ELI) is able to predict Eastern Pacific hurricane activity at significant lead times. By capturing changes in the location of deep convection and associated thermocline processes more accurately, ELI explains the most variability in the upper-ocean heat content in the main development region of the Eastern Pacific basin compared to other ENSO indices. These results have substantial implications for operational seasonal forecasts of Eastern Pacific hurricanes.

Balaguru, Karthik↗
DOE OSTI2026

Ion Cyclotron Heating in a Levitated Dipole Fusion Reactor

OpenStar Technologies is pursuing the levitated dipole (LD) as a highly modular, loosely-coupled system that leverages their expertise in high temperature superconductor (HTS) technology. The next generation experiment at OpenStar, Tahi (Ma¯ori for “first”), will demonstrate the generation and confinement of fast ions in a levitated dipole for the first time. Ion cyclotron range of frequency (ICRF) heating is a leading candidate for energetic ion formation in Tahi. A frequency in the 10 MHz range will be used for H minority heating or D majority heating with waves launched from an antenna located above the floating coil. Unlike a tokamak, where the targeted cyclotron resonance is typically a vertical path through the center of the plasma, in a dipole the resonance location follows a C-shaped path from the separatrix to the center of the plasma. The value of B also varies significantly within the confined plasma resulting in a large number of cyclotron harmonics present in the low field region. Furthermore, levitated dipoles contain a “first closed flux surface” surrounding the floating coil, in addition to the traditional separatrix /last closed flux surface. Simulation e ff orts using full-wave ICRF codes show that ICRF heating of a levitated dipole reactor is feasible using a pair of toroidal current straps phased to launch the appropriate parallel ( i.e. poloidal) refractive index.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Sequential versus Simultaneous Aging of EPDM Nuclear Cable Insulation Subjected to Elevated Temperature and Gamma Radiation

Electrical cables are integral to power, control, and instrumentation systems within nuclear power plants (NPPs). Exposure of cable systems within nuclear containment to elevated temperatures and gamma radiation during decades-long operation of NPPs can lead to degradation of cable polymeric insulation. Prediction of nuclear cable insulation degradation is complicated as thermal and radiation stress are not additive. In this work, we explore the relative effects of simultaneous and sequential thermal and gamma irradiation on the aging of ethylene-propylene-diene (EPDM) elastomer insulation to better understand realistic scenarios of cable insulation degradation. Cable insulation samples of EPDM were subjected to up to 320 kGy of gamma radiation at a dose rate of 300 Gy/hr in two heating scenarios: (1) simultaneously aged samples were heated at 150°C during irradiation and (2) sequentially aged samples were heated at 150°C for designated durations followed by corresponding periods of irradiation at ambient temperature. The mass, tensile elongation at break, and carbonyl index were assessed to quantify aging of the polymers. The simultaneous aging scenario was found to the more severe of the two for EPDM insulation degradation.

ethylene-propylene-diene elastomer, EPDM, nuclear ↗
DOE OSTI2024

Identification of surface urban heat versus cool islands for arid cities depends on the choice of urban and rural definitions

The urban heat island (UHI) effect in arid cities can be small or even negative, the latter known as the urban cool island (UCI) effect. Differences in defining urban and rural areas can introduce uncertainties in detecting UHI or UCI, especially when the UHI signal is small. Here, we compared the surface UHI intensity (SUHII) estimated by a dozen different methods (with multiple urban and/or rural definitions) across 104 arid cities globally, providing a comprehensive evaluation of the uncertainty in SUHII estimates. Results show that the absolute difference in annual average SUHII (ΔSUHII) among methods exceeded 1°C in about half of the arid cities during both daytime and nighttime. Further, the overall annual mean ΔSUHII for all arid cities was 1.35°C during daytime and 1.03 °C at night. The uncertainty arising from simultaneous variations in urban and rural definitions was generally higher than that resulting from their individual changes. It was observed that, with varying definitions of urban and rural areas, nearly 50% of arid cities experienced a sign reversal in daytime SUHII estimates, while approximately 15% exhibited a sign reversal in nighttime SUHII. Variations in urban-rural differences in surface properties, such as vegetation index and albedo, due to differing urban and rural definitions, contributed strongly to the observed SUHII uncertainties. Overall, our results offer new insights into the ongoing debate on heat and cold islands in arid cities, emphasizing a critical need to standardize SUHII estimation frameworks.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Strong Local Evaporative Cooling Over Land Due to Atmospheric Aerosols

Abstract Aerosols can enhance terrestrial productivity through increased absorption of solar radiation by the shaded portion of the plant canopy—the diffuse radiation fertilization effect. Although this process can, in principle, alter surface evaporation due to the coupling between plant water loss and carbon uptake, with the potential to change the surface temperature, aerosol‐climate interactions have been traditionally viewed in light of the radiative effects within the atmosphere. Here, we develop a modeling framework that combines global atmosphere and land model simulations with a conceptual diagnostic tool to investigate these interactions from a surface energy budget perspective. Aerosols increase the terrestrial evaporative fraction, or the portion of net incoming energy consumed by evaporation, by over 4% globally and as much as ∼40% regionally. The main mechanism for this is the increase in energy allocation from sensible to latent heat due to global dimming (reduction in global shortwave radiation) and slightly augmented by diffuse radiation fertilization. In regions with moderately dense vegetation (leaf area index >2), the local surface cooling response to aerosols is dominated by this evaporative pathway, not the reduction in incident radiation. Diffuse radiation fertilization alone has a stronger impact on gross primary productivity (+2.18 Pg C y −1 or +1.8%) than on land evaporation (+0.18 W m −2 or +0.48%) and surface temperature (−0.01 K). Our results suggest that it is important for land surface models to distinguish between quantity (change in total magnitude) and quality (change in diffuse fraction) of radiative forcing for properly simulating surface climate.

Chakraborty, TC↗
DOE OSTI2020

Ability of Particulate Matter Index to describe sooting tendency of various gasoline formulations in a stratified-charge spark-ignition engine

This study investigates the ability of Particulate Matter Index (PMI) to describe the sooting behavior of various gasoline formulations in a stratified-charge (SC) spark-ignition engine. Specifically, the engine was operated at 2000 rpm with an intake pressure of 130 kPa where soot formation is known to primarily occur in the bulk gases. Exhaust soot emissions were measured for nine test fuels at various exhaust gas recirculation levels. A comparison between measured soot levels and PMI shows that PMI is a relatively poor predictor of the sooting tendency of the tested fuels under lean SC combustion. Among the fuels, three fuels, namely the diisobutylene blend, High Olefin, and E30 fuels exhibit measured soot behavior opposite of that predicted by PMI. Optical diagnostics were utilized to further investigate the in-cylinder phenomena for these three fuels. Analysis of natural luminosity and diffused back-illumination extinction imaging suggests that fuel-induced differences in the amount of soot formed are responsible for a majority of the discrepancy in measured versus predicted sooting tendency. Fuel-induced differences in soot oxidation and spray development seem to play minor roles. Because the combustion and air-fuel mixing processes for lean SC combustion are different from conventional stoichiometric operation it is hypothesized that the PMI correlation needs to be modified to account for differences in stoichiometric air-fuel ratio and level of oxygenation between fuels. Furthermore, the role of fuel volatility in PMI possibly needs to be de-emphasized for SC operation with fuel injection into compression-heated gases.

42 ENGINEERING↗
DOE OSTI2022

Reconnection-driven energy cascade in magnetohydrodynamic turbulence

Magnetohydrodynamic turbulence regulates the transfer of energy from large to small scales in many astrophysical systems, including the solar atmosphere. We perform three-dimensional magnetohydrodynamic simulations with unprecedentedly large magnetic Reynolds number to reveal how rapid reconnection of magnetic field lines changes the classical paradigm of the turbulent energy cascade. By breaking elongated current sheets into chains of small magnetic flux ropes (or plasmoids), magnetic reconnection leads to a previously undiscovered range of energy cascade, where the rate of energy transfer is controlled by the growth rate of the plasmoids. As a consequence, the turbulent energy spectra steepen and attain a spectral index of -2.2 that is accompanied by changes in the anisotropy of turbulence eddies. The omnipresence of plasmoids and their consequences on, for example, solar coronal heating, can be further explored with current and future spacecraft and telescopes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Small-scale validation tests for MFIX-Exa CFD-DEM

This report describes several bench-scale fluidization experiments that can be used to validate the CFD-DEM method as encapsulated in the MFIX-Exa code. The five cases considered are the cold-flow fluidized beds of Müller et al., Link et al. (spout-fluid), and Goldschmidt et al. (bi-disperse), the hot fluidized bed of Patil et al., and the adsorbing fluidized bed of Li et al. and Janssen. In most cases, MFIX-Exa with “standard” or “typical” CFD-DEM settings, the Gidaspow drag model, and the Gunn heat transfer provide a relatively good prediction of the quantities considered: mean void fraction profiles, mean velocity profiles, fluctuating velocity profiles, mean particle temperature and segregation index. These results, with other verification and validation tests reported elsewhere, contribute to a body of work providing confidence and credibility in CFD predictions from the MFIX-Exa code.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI1988

Nuclear Safety [Vol. 29, No. 1, January-March 1988]

Nuclear Safety is a review journal that covers significant developments in the field of nuclear safety. Its scope includes the analysis and control of hazards associated with nuclear energy, operations involving fissionable materials, and the products of nuclear fission and their effects on the environment. Primary emphasis is on safety in reactor design, construction, and operation; however, the safety aspects of the entire fuel cycle, including fuel fabrication, spent-fuel processing, nuclear waste disposal, handling of radioisotopes, and environmental effects of these operations, are also treated. Table of Contents for this issue follows. THE CHERNOBYL ACCIDENT: 1 Core History and Nuclide Inventory of the Chernobyl Core at the Time of Accident by Gerald Kirchner and Cornelius C. Noack; GENERAL SAFETY CONSIDERATIONS: 6 Nonprescriptive Nuclear Safety Regulation: The Example of Loss of Offsite Power by M. W. Golay, V. P. Manno, and C. Vlahoplus, Jr., 20 Nuclear Power Safety Goals in Light of the Chernobyl Accident by C. Whipple and C. Starr; ACCIDENT ANALYSIS: 29 Containment Loads from Severe Accidents—U.S. Program by W. Kerr and M. K. Dey; PLANT SAFETY FEATURES: 36 Safety Characteristics of Modern High-Temperature Reactors: Focus on German Designs by W. Kröger, H. Nickel, and R. Schulten; ENVIRONMENTAL EFFECTS: 49 Radiation Hormesis and Nuclear Safety by C. C. Congdon; OPERATING EXPERIENCES: 58 Evaluation of Nonradiological Water Chemistry at Power Reactors by Harvey Zibulsky, James J. Kottan, Walter J. Pasciak, Mary Ann Castrogivanni, and Sujit Banerjee, 64 Reactor Shutdown Experience Compiled by J. W. Cletcher, 67 Operating U.S. Power Reactors Compiled by E. G. Silver; RECENT DEVELOPMENTS: 85 General Administrative Activities Compiled by E. G. Silver, 94 Reports, Standards, and Safety Guides by D. S. Queener, 100 Status of Power-Reactor Projects Undergoing Licensing Review Compiled by E. G. Silver, 103 Proposed Rule Changes as of Sept. 30, 1987; ANNOUNCEMENTS: 5 Northwestern University Short Course on Radiation Safety, 28 International Approach to Nuclear Safety (After Three-Mile Island and Chernobyl), 57 RPI Short Course on Modern Developments in Boiling Heat Transfer and Two-Phase Flow, 107 20th DOE/NRC Nuclear Air Cleaning Conference, 110 Third International Topical Meeting on Nuclear Power Plant Thermal Hydraulics and Operations, 108 The Authors, 111 Indexes to Nuclear Safety, Volume 28.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Effects of shielding gas and spot reduction on humping suppression in high-speed laser welding

High-speed laser welding is a crucial process to enhance the production rate of fuel cell fabrication. However, exceeding a critical welding speed leads to defect formation such as humps and root concavities, which degrade weld quality and mechanical performance. This study employed shielding gas and spot reduction approaches to suppress these defects. The relationships between individual defect types and their influence on weld strength were systematically examined. Moreover, in situ high-speed synchrotron X-ray imaging was employed to comprehend the mechanisms of humping mitigation by shielding gas through analysis of instantaneous keyhole and melt pool dynamics. The observations reveal that shielding gas mitigates humping by shortening the molten pool through enhanced surface heat convection and by altering surface tension to prevent melt flow collisions. The effects of shielding gas and spot reduction were further incorporated into the dimensionless humping index (π h ) that describes the humping formation tendency. These findings provide mechanistic insights and quantitative guidance for defect control strategies in high-speed laser welding.

08 HYDROGEN↗
DOE OSTI2021

Application of Principal Component Analysis for the Monitoring of the Aging Process of Nuclear Electrical Cable Insulation

To ensure the safe operation of nuclear power plants (NPPs), it is critical to understand how NPP electrical cable insulation will degrade under different service environments. In this study, various nondestructive examination methods were selected to evaluate degradation of electrical cable insulation after aging. Elongation at break, indenter modulus, relaxation constant, mass change, total color difference, and carbonyl index were collected stepwise on cross-linked polyethylene (XLPE) cable insulations after predetermined exposure intervals. Three different insulation aging scenarios were investigated: 1) simultaneous irradiation and heating at 150°C, 2) heating at 150°C followed by corresponding times of irradiation at ambient temperature, and 3) irradiation at ambient temperature followed by heating at 150°C for the same duration. A constant dose rate of 300 Gy/hr was selected with a total gamma irradiation absorbed dose up to 320 kGy. To gain insight into the long-term performance of NPP electrical cable insulation, principal component analysis (PCA), a data-driven approach, was utilized to identify key indicators of cable insulation degradation. By reducing the dimensionality of the data while retaining degradation information, PCA was used to highlight the changes in the measured properties under gamma irradiation according to total absorbed dose and the different aging scenarios.

Li, Donghui↗