Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HTTR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

80 records · Page 5

Accelerator-Based Irradiation Creep of Pyrolytic Carbon Used in TRISO Fuel Particles for the (VHTR) Very Hight Temperature Reactors

Pyrolytic carbon (PyC) is one of the important structural materials in the TRISO fuel particles which will be used in the next generation of gas-cooled very-high-temperature reactors (VHTR). When the TRISO particles are under irradiation at high temperatures, creep of the PyC layers may cause radial cracking leading to catastrophic particle failure. Therefore, a fundamental understanding of the creep behavior of PyC during irradiation is required to predict the overall fuel performance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

SCALE Code Validation for Prismatic High-Temperature Gas-Cooled Reactors

Using experimental data published in the International Handbook of Evaluated Reactor Physics Benchmark Experiments for the fresh cold core of the High Temperature Engineering Test Reactor, a comprehensive validation study has been carried out to assess the performance of the SCALE code system for analysis of high-temperature gas-cooled reactor configurations. This paper describes part of the results of that effort. The studies performed included criticality evaluations for the full core and for the annular cores realized during the fuel loading, as well as calculations and comparisons for excess reactivity, shutdown margin, control rod worths, temperature coefficient of reactivity, and reaction rate distributions. Comparisons of the SCALE results with both experimental values and MCNP-calculated values are presented. The comparisons show that the SCALE calculated results, obtained with both multigroup and continuous energy cross sections, are in reasonable agreement with the experimental data and the MCNP predictions.

code validation↗

The COMET method in 3-D hexagonal geometry

The hybrid stochastic-deterministic coarse mesh radiation transport (COMET) method developed at Georgia Tech now solves reactor core problems in 3-D hexagonal geometry. In this paper, the method is used to solve three preliminary test problems designed to challenge the method with steep flux gradients, high leakage, and strong asymmetry and heterogeneity in the core. The test problems are composed of blocks taken from a high temperature test reactor benchmark problem. As the method is still in development, these problems and their results are strictly preliminary. Results are compared to whole core Monte Carlo reference solutions in order to verify the method. Relative errors are on the order of 50 pcm in core eigenvalue, and mean relative error in pin fission density calculations is less than 1% in these difficult test cores. The method requires the one-time pre-computation of a response expansion coefficient library, which may be compiled in a comparable amount of time to a single whole core Monte Carlo calculation. After the library has been computed, COMET may solve any number of core configurations on the order of an hour, representing a significant gain in efficiency over other methods for whole core transport calculations. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Preliminary requirements for a Fluoride Salt-Cooled High-Temperature Test Reactor (FHTR)

A Fluoride Salt-Cooled High-Temperature Test Reactor (FHTR) design is being developed at MIT to provide the first demonstration and test of a salt-cooled reactor using high-temperature fuel. The first step is to define the requirements. The top level requirements are (1) provide the confidence that a larger demonstration reactor is warranted and (2) develop the necessary data for a larger-scale reactor. Because requirements will drive the design of the FHTR, a significant effort is being undertaken to define requirements and understand the tradeoffs that will be required for a practical design. The preliminary requirements include specifications for design parameters and necessary tests of major reactor systems. Testing requirements include demonstration of components, systems, and procedures for refueling, instrumentation, salt temperature control to avoid coolant freezing, salt chemistry and volume control, tritium monitoring and control, and in-service inspection. Safety tests include thermal hydraulics, neutronics - including intrinsic core shutdown mechanisms such as Doppler feedback - and decay heat removal systems. Materials and coolant testing includes fuels (including mechanical wear and fatigue) and system corrosion behavior. Preliminary analysis indicates a thermal power output below 30 MW, an initial core using pebble-bed or prismatic-block fuel, peak outlet temperatures of at least 700 deg. C, and use of FLi{sup 7}Be ({sup 7}LiF-BeF{sub 2}) coolant. The option to change-out the reactor core, fuel type, and major components is being investigated. While the FHTR will be used for materials testing, its primary mission is as a reactor system performance test to enable the design and licensing of a FHR demonstration power reactor. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Study on balance of axial force in helium circulator for HTR-PM - 18490

The helium circulator is one of the key equipment in the first loop of the High Temperature gas-cooled Reactor Pebble bed Module (HTR-PM). The active magnetic bearings are employed in the helium circulator, so that the inlet ring sealing clearance is about 5 to 10 times larger than that if the mechanical bearings are employed. Bigger clearance results in bigger leakage flow and bigger axial force. A new design of balance holes was proposed to reduce the axial aerodynamic force and the design principle was analyzed. To investigate the axial aerodynamic force due to leakage flow, numerical simulation of fluid dynamic was conducted in the impeller with two kinds of inlet ring sealing clearance and four types of balance holes, respectively. The calculation results shows that the balance holes with diameter 12 mm have high performance and that the designed balance holes reduce effectively about 78% of the axial aerodynamic force. The axial force was obtained from the measured real-time electric current of the axial active magnetic bearings in one helium circulator prototype. The comparison of experimental data with the CFD analysis results showed that the new design of balance holes was successful. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Analysis of the High Temperature Engineering Test Reactor Using MOOSE Tools

This presentation shows the development of neutronics and thermal hydraulics models of the High Temperature Engineering Test Reactor using codes in the Multiphysics Object Oriented Simulation Environment. We show preliminary results of full-power steady state and a loss of forced cooling transient from that steady state.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗

BENCHMARK EVALUATION OF THE START-UP CORE REACTOR PHYSICS MEASUREMENTS OF THE HIGH TEMPERATURE ENGINEERING TEST REACTOR

The benchmark evaluation of the start-up core reactor physics measurements performed with Japan’s High Temperature Engineering Test Reactor, in support of the Next Generation Nuclear Plant Project and Very High Temperature Reactor Program activities at the Idaho National Laboratory, has been completed. The evaluation was performed using MCNP5 with ENDF/B-VII.0 nuclear data libraries and according to guidelines provided for inclusion in the International Reactor Physics Experiment Evaluation Project Handbook. Results provided include updated evaluation of the initial six critical core configurations (five annular and one fully-loaded). The calculated keff eigenvalues agree within 1s of the benchmark values. Reactor physics measurements that were evaluated include reactivity effects measurements such as excess reactivity during the core loading process and shutdown margins for the fully-loaded core, four isothermal temperature reactivity coefficient measurements for the fully-loaded core, and axial reaction rate measurements in the instrumentation columns of three core configurations. The calculated values agree well with the benchmark experiment measurements. Fully subcritical and warm critical configurations of the fully-loaded core were also assessed. The calculated keff eigenvalues for these two configurations also agree within 1s of the benchmark values. The reactor physics measurement data can be used in the validation and design development of future High Temperature Gas-cooled Reactor systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Current Status of VHTR Technology Development

Abstract – High Temperature Gas-cooled Reactors (HTGRs) featuring particle fuel reached the stage of commercial deployment in the mid-1980s with the Fort St.Vrain and Thorium HochTemperatur Reaktor feeding electricity to the grids in the United States and West Germany, respectively. The technology was then adopted by Japan and China with the operation of the High Temperature Test Reactor in Oarai, Japan and the High Temperature Reactor (HTR-10) in China. Increasing the outlet temperature of the HTGR to even higher temperatures above 900°C will improve the thermodynamic efficiency of the system and enable application of a new class of gas reactor, the very high temperature reactor, to provide process heat, electricity, and hydrogen to chemical industries with the attendant benefits of improved energy security and reduced CO2 emissions. However, the increase in coolant outlet temperature presents a number of technical challenges associated with fuel, materials, power conversion, and analysis methods for the reactor and hydrogen production. The U.S. Department of Energy is sponsoring a broad program of research and development with a goal of addressing the technical challenges over a broad range of outlet temperatures as part of the Next Generation Nuclear Plant Project. This paper describes the research and development activities that are currently underway to realize the technologies needed for an HTGR that features outlet temperatures of 750 to 950°C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗