Results for “Fixed Base” — Page 5

NASA NTRSDate not supplied

Dynamic Characterization of NASA Armstrong Test Facility Mechanical Vibration Facility

In preparation for Sierra Nevada Corporation’s (SNC) Dream Chaser spacecraft vibration test campaign at NASA Armstrong Test Facility (ATF) in Sandusky, Ohio, a dynamic characterization of the Mechanical Vibration Facility (MVF) is currently ongoing. The Mechanical Vibration Facility is comprised of an 18 ft diameter annulus table that is driven with sixteen hydraulic vertical actuator assemblies and four hydraulic horizontal actuator assemblies. During a test campaign this allows for single axis vibration testing in the vertical axis and in each of the two orthogonal horizontal axes without the need for reconfiguring the test article. The dynamic characterization of the facility was defined to follow a building-block approach requiring three vibration test configurations: (1) MVF bare table (2) MVF table and head expander (3) MVF table, head expander, and a dummy test article. Following the completion of the facility dynamic characterization, a facility finite element model (FEM) will be test-verified allowing for more accurate pretest analysis used for determining response limits and abort levels. To date two of the three test configurations have been completed. Test results have been used to verify the facility FEM that includes both the 18 ft diameter annulus table and the aluminum head expander that fills in the center opening of the annulus to provide a continuous flat mounting surface. Both the MVF table and the head expander models were previously correlated using test results from free-free boundary condition modal tests so model updates to the facility FEM focused on the uncorrelated vertical actuator assemblies and horizontal actuator assemblies. The accuracy of the test-verified facility FEM will be further determined based on comparison of analytical and test results from the vibration test of the dummy test article. Efforts will also be made to determine fixed base modes of the test article attached to the flexible vibration table using fixed base correction techniques. This paper will discuss test and analytical results from the MVF dynamic characterization test sequence and corresponding model updating effort.

Emma L Pierson↗

NASA NTRS1991

On the nature of control algorithms for free-floating space manipulators

It is suggested that nearly any control algorithm that can be used for fixed-based manipulators also can be employed in the control of free-floating space manipulator systems, with the additional conditions of estimating or measuring a spacecraft's orientation and of avoiding dynamic singularities. This result is based on the structural similarities between the kinematic and dynamic equations for the same manipulator but with a fixed base. Barycenters are used to formulate the kinematic and dynamic equations of free-floating space manipulators. A control algorithm for a space manipulator system is designed to demonstrate the value of the analysis.

Papadopoulos, Evangelos↗

NASA NTRS1984

The Shuttle Mission Simulator computer generated imagery

Equipment available in the primary training facility for the Space Transportation System (STS) flight crews includes the Fixed Base Simulator, the Motion Base Simulator, the Spacelab Simulator, and the Guidance and Navigation Simulator. The Shuttle Mission Simulator (SMS) consists of the Fixed Base Simulator and the Motion Base Simulator. The SMS utilizes four visual Computer Generated Image (CGI) systems. The Motion Base Simulator has a forward crew station with six-degrees of freedom motion simulation. Operation of the Spacelab Simulator is planned for the spring of 1983. The Guidance and Navigation Simulator went into operation in 1982. Aspects of orbital visual simulation are discussed, taking into account the earth scene, payload simulation, the generation and display of 1079 stars, the simulation of sun glare, and Reaction Control System jet firing plumes. Attention is also given to landing site visual simulation, and night launch and landing simulation.

Henderson, T. H.↗

NASA NTRS1994

Bolt and nut evaluator

A device for testing fasteners such as nuts and bolts is described which consists of a fixed base plate having a number of threaded and unthreaded holes of varying size for receiving the fasteners to be tested, a torque marking paper taped on top the fixed base plate for marking torque-angle indicia, a torque wrench for applying torque to the fasteners being tested, and an indicator for showing the torque applied to the fastener. These elements provide a low cost, nondestructive device for verifying the strength of bolts and nuts.

Kerley, James J.↗

NASA NTRS1969

Connect-disconnect coupling for preadjusted rigid shafts

Coupling device enables a rigid shaft to be connected to or disconnected from a fixed base without disturbing the point of adjustment of the shaft in a socket or causing the shaft to rotate. The coupling consists of an externally threaded, internally slotted boss extending from the fixed base.

Bajkowski, F. W.↗

NASA NTRS1990

The kinematics and dynamics of space manipulators - The virtual manipulator approach

Future robotic manipulator systems will be required to perform complex tasks in space such as satellite repair. These robotic manipulators will encounter a number of kinematic, dynamic, and control problems caused by the dynamic coupling between the manipulators and its spacecraft. This dynamic coupling also makes it difficult to analyze these systems. This paper introduces a new analytical modeling method for space manipulators called the Virtual Manipulator (VM), which has a fixed based in inertial space at a point called a Virtual Ground. The kinematics and dynamics of the manipulator, spacecraft, and payload can be described relatively easily in terms of the VM. With its fixed base, the Virtual Manipulator is shown to have the potential to be an effective aid for the analysis, design, and development of future space manipulator systems.

Vafa, Z.↗

NASA NTRS1994

Residual flexibility test method for verification of constrained structural models

A method is described for deriving constrained modes and frequencies from a reduced model based on a subset of the free-free modes plus the residual effects of neglected modes. The method involves a simple modification of the MacNeal and Rubin component mode representation to allow development of a verified constrained (fixed-base) structural model. Results for two spaceflight structures having translational boundary degrees of freedom show quick convergence of constrained modes using a measureable number of free-free modes plus the boundary partition of the residual flexibility matrix. This paper presents the free-free residual flexibility approach as an alternative test/analysis method when fixed-base testing proves impractical.

Admire, John R.↗

NASA NTRS1977

Recent ground-based and in-flight simulator studies of low-speed handling characteristics of supersonic cruise transport aircraft

Several advanced arrow-wing concepts have evolved from NASA's Supersonic Cruise Aircraft Research (SCAR) Program. Evaluations of the low-speed handling characteristics of these configurations have been conducted at Langley Research Center using a fixed-base ground simulator with a visual landing scene. A brief in-flight simulation program was also conducted using Calspan's Total In-Flight Simulator (TIFS) in order to provide: (1) points of reference for interpretation of the ground-simulator results, (2) data for control-system design tradeoffs, and (3) data on effects of real-world visual height cues and cockpit-motion cues not available in the fixed-base simulation. The more significant results of these studies are presented.

Grantham, W. D.↗

NASA NTRS1985

An investigation into the vertical axis control power requirements for landing VTOL type aircraft onboard nonaviation ships in various sea states

The problem of determining the vertical axis control requirements for landing a VTOL aircraft on a moving ship deck in various sea states is examined. Both a fixed-base piloted simulation and a nonpiloted simulation were used to determine the landing performance as influenced by thrust-to-weight ratio, vertical damping, and engine lags. The piloted simulation was run using a fixed-based simulator at Ames Research center. Simplified versions of an existing AV-8A Harrier model and an existing head-up display format were used. The ship model used was that of a DD963 class destroyer. Simplified linear models of the pilot, aircraft, ship motion, and ship air-wake turbulence were developed for the nonpiloted simulation. A unique aspect of the nonpiloted simulation was the development of a model of the piloting strategy used for shipboard landing. This model was refined during the piloted simulation until it provided a reasonably good representation of observed pilot behavior.

Stevens, M. E.↗

NASA NTRSDate not supplied

Alternate Methods of Model Reduction to Avoid Dynamic Modal Truncation Error

Loads analysis is traditionally performed using dynamically reduced models, which provides the benefit to reduce run time. If the reduced model frequency cutoff is not chosen appropriately, the model will lack the dynamic content required to fully represent the response of the non-reduced model. Standard guidance for reduced model frequency content, provided in NASA-STD-5002, is to solve fixed base modes up to a minimum of 1.5x the model frequency content of interest and to employ static modal truncation methods such as residual vectors, the mode acceleration method, and the residual flexibility method to account for the truncated flexibility of the missing modes. Fixed base modes require the selection of a set of degrees of freedom to be constrained which, if not properly selected, may affect the accuracy of the reduced model by excluding some of the dynamic characteristic of the full model. In this case, the standard NASA guidance would be insufficient, but it may not be readily apparent that a portion of the reduced model response is missing. This error was encountered during an independent verification and validation (IV&V) effort, where it was observed that the resulting dynamic response was lower than the inline analysis. In this specific case, despite following the standard NASA model reduction guidelines in the selection of the frequency cutoff, the inline model still did not fully capture the necessary dynamic content. As part of the IV&V, an alternate reduction methodology was employed using an unconstrained mode acceleration method. The original model initially performed a constrained reduction to twice the frequency content of interest before doing a free-free run, employing the mode acceleration method to account for the truncated modes. In contrast in the IV&V, the unconstrained model reduced directly to the needed frequency content of the free-free run, avoiding any interactions between constraints and dynamic content. To verify the model, the original reduction methodology was used to generate a series of Hurty-Craig-Bampton reductions, each with a higher frequency cutoff than the previous. The results were shown to converge once the frequency cutoff increased past eight times the frequency content of interest. At the same frequency cutoff, the results of the Hurty-Craig-Bampton model converged with the results of the unconstrained mode acceleration model. This comparative study provided confidence that the results of the unconstrained modal acceleration reduced model were correct and that the Hurty-Craig-Bampton needed to increase its frequency cutoff to fully capture the dynamic response.

Erin Simmons↗

NASA NTRSDate not supplied

Alternate Methods of Model Reduction to Avoid Dynamic Modal Truncation Error

Loads analysis is traditionally performed using dynamically reduced models, which provides the benefit to reduce run time. If the reduced model frequency cutoff is not chosen appropriately, the model will lack the dynamic content required to fully represent the response of the non-reduced model. Standard guidance for reduced model frequency content, provided in NASA-STD-5002, is to solve fixed base modes up to a minimum of 1.5x the model frequency content of interest and to employ static modal truncation methods such as residual vectors, the mode acceleration method, and the residual flexibility method to account for the truncated flexibility of the missing modes. Fixed base modes require the selection of a set of degrees of freedom to be constrained which, if not properly selected, may affect the accuracy of the reduced model by excluding some of the dynamic characteristic of the full model. In this case, the standard NASA guidance would be insufficient, but it may not be readily apparent that a portion of the reduced model response is missing. This error was encountered during an independent verification and validation (IV&V) effort, where it was observed that the resulting dynamic response was lower than the inline analysis. In this specific case, despite following the standard NASA model reduction guidelines in the selection of the frequency cutoff, the inline model still did not fully capture the necessary dynamic content. As part of the IV&V, an alternate reduction methodology was employed using an unconstrained mode acceleration method. The original model initially performed a constrained reduction to twice the frequency content of interest before doing a free-free run, employing the mode acceleration method to account for the truncated modes. In contrast in the IV&V, the unconstrained model reduced directly to the needed frequency content of the free-free run, avoiding any interactions between constraints and dynamic content. To verify the model, the original reduction methodology was used to generate a series of Hurty-Craig-Bampton reductions, each with a higher frequency cutoff than the previous. The results were shown to converge once the frequency cutoff increased past eight times the frequency content of interest. At the same frequency cutoff, the results of the Hurty-Craig-Bampton model converged with the results of the unconstrained mode acceleration model. This comparative study provided confidence that the results of the unconstrained modal acceleration reduced model were correct and that the Hurty-Craig-Bampton needed to increase its frequency cutoff to fully capture the dynamic response.

Erin Simmons↗

NASA NTRS1973

A comparison of results from two simulators used for studies of astronaut maneuvering units

A comparison of the results from a fixed-base, six-degree-of -freedom simulator and a moving-base, three-degree-of-freedom simulator was made for a close-in, EVA-type maneuvering task in which visual cues of a target spacecraft were used for guidance. The maneuvering unit (the foot-controlled maneuvering unit of Skylab Experiment T020) employed an on-off acceleration command control system operated entirely by the feet. Maneuvers by two test subjects were made for the fixed-base simulator in six and three degrees of freedom and for the moving-base simulator in uncontrolled and controlled, EVA-type visual cue conditions. Comparisons of pilot ratings and 13 different quantitative parameters from the two simulators are made. Different results were obtained from the two simulators, and the effects of limited degrees of freedom and uncontrolled visual cues are discussed.

Stewart, E. C.↗

NASA NTRS1976

The Influence of Loss of Visual Cues on Pilot Performance During the Final Approach and Landing Phase of a Remotely Piloted Vehicle Mission

Remotely piloted research vehicles (RPRVS) are currently being flown from fixed-base control centers, and visual information is supplied to the remote pilot by a TV camera mounted in the vehicle. In these circumstances, the possibility of a TV failure or an interruption in the downlink to the pilot must be considered. To determine the influence of loss of TV information on pilot performance during the final approach and landing phase of a mission, an experiment was conducted in which pilots were asked to fly a fixed-base simulation of a Piper PA-30 aircraft with loss of TV information occurring at altitudes of 15.24, 30.48, and 45.72 m (50, 100, and 150 ft). For this experiment, a specially designed display configuration was presented to four pilots in accordance with a Latin square design. Initial results indicate that pilots could not ensure successful landings from altitudes exceeding 15.24 m (.50 ft) without the visual cues supplied by the TV picture.

Howard, James C.↗

NASA NTRS1975

The influence of radio altimeter errors on pilot performance during the final approach and landing phase of an RPV mission

Due to the fact that remotely piloted vehicles (RPV's) are currently being flown from fixed base control centers, kinesthetic and real world peripheral vision cues are absent. The absence of these cues complicates the piloting task, particularly during the final approach and landing phase of a mission. The pilot's task is futher complicated by errors in the displayed altitude information. To determine the influence of these errors on pilot performance during the final approach and landing phase of a mission, an experiment was conducted in which pilot subjects were asked to fly a fixed base simulation of a Piper PA-30 aircraft, using degraded altitude information. For this experiment, the chevron component of the display configuration was driven by a radio altimeter. Four altimeters were used, each with a different error characteristic, but within the range specified for the Sperry series of radio altimeters. Results indicate that for range of errors considered, there is no significant difference in landing performance that can be attributed to errors in altitude information.

Howard, J. C.↗

NASA NTRS1992

Piloted evaluation of an integrated propulsion and flight control simulator

This paper describes a piloted evaluation of the integrated flight and propulsion control simulator at NASA Lewis Research Center. The purpose of this evaluation is to demonstrate the suitability and effectiveness of this fixed based simulator for advanced integrated propulsion and airframe control design. The evaluation will cover control effector gains and deadbands, control effectiveness and control authority, and heads up display functionality. For this evaluation the flight simulator is configured for transition flight using an advanced Short Take-Off and vertical Landing fighter aircraft model, a simplified high-bypass turbofan engine model, fighter cockpit, displays, and pilot effectors. The paper describes the piloted tasks used for rating displays and control effector gains. Pilot comments and simulation results confirm that the display symbology and control gains are very adequate for the transition flight task. Additionally, it is demonstrated that this small-scale, fixed base flight simulator facility can adequately perform a real time, piloted control evaluation.

Bright, Michelle M.↗

NASA NTRS2020

Comparing Virtual Reality to Conventional Simulator Visuals: Effects of Peripheral Visual Cues in Roll-Axis Tracking Tasks

This paper compares the effects of peripheral visual cues on manual control between a conventional fixed-base simulator and virtual reality. The results were also compared with those from a previous experiment conducted in a motion-base simulator. Fifteen participants controlled a system with second-order dynamics in a disturbance-rejection task. Tracking performance, control activity, simulator sickness questionnaire answers, and biometrics were collected. Manual control behavior was modeled for the first time in a virtual reality environment. Virtual reality did not degrade participants’ manual control performance or alter their control behavior. However, peripheral cues were significantly more effective in virtual reality. Control activity decreased for all conditions with peripheral cues. The trends introduced by the peripheral visual cues from the previous experiment were replicated. Finally, VR was not more nauseogenic than the conventional simulator. These results suggest that virtual reality might be a good alternative to conventional fixed-base simulators for training manual control skills.

Terenzi, Lorenzo↗

NASA NTRS1979

Advanced transport operation effects on pilot scan patterns

Long straight-in and close-in, curved, descending instrument approaches were made in NASA's fixed-base Terminal Configured Vehicle simulator. The pilot either manually controlled the simulator or monitored the automatic system control of the simulated aircraft during the approach. Tests were performed with or without the display of traffic. The results indicate that the pilots' use of the Electronic Horizontal Situation Indicator (EHSI) increased appreciably for the close-in, curved, descending approach compared to the conventional straight-in approach. When operating as a monitor of the autopilot system, the pilot scanned around more with less attention devoted to the Electronic Attitude Direction Indicator (EADI). The pilots preferred the manual mode because it kept them in the control loop. The addition of displayed traffic to the EHSI increased the pilots' use of the EHSI with a corresponding reduction in his use of the EADI. Also, the pilot's pupil diameter increased during the landing flare indicating a higher stress level even though the tests were conducted in a fixed-base simulator.

Harris, R. L., Sr.↗

NASA NTRS1986

Mission and space vehicle sizing data for a chemical propulsion/aerobraking option

This paper presents sizing data for various combinations of Mars missions and chemical-propulsion/aerobraking vehicles. Data is compared for vehicles utilizing opposition (2-year mission) and conjunction (3-year mission) trajectories for 1999 and 2001 opportunities, for various sizes of vehicles. Payload capabilities for manned and unmanned missions vehicles and for propulsive-braking and aerobraking cases are shown. The effect of scaling up a reference vehicle Is compared to the case of utilizing two identical vehicles, for growth In payload capability. The rate of cumulative build up of weight on the surface of Mars is examined for various mission/vehicle combinations, and is compared to the landed-weight requirements for sortie missions, moving-base missions, and fixed-base missions. Also, the required buildup of weight in low Earth orbit (LEO) for various mission/vehicle combinations Is presented and discussed.

John Butler↗