Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLEXURAL STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

An experimental study of the mechanism of failure of rocks under borehole jack loading

Laboratory and field tests with an experimental jack and an NX-borehole jack are reported. The following conclusions were made: Under borehole jack loading, a circular opening in a brittle solid fails by tensile fracturing when the bearing plate width is not too small. Two proposed contact stress distributions can explain the mechanism of tensile fracturing. The contact stress distribution factor is a material property which can be determined experimentally. The borehole tensile strength is larger than the rupture flexural strength. Knowing the magnitude and orientation of the in situ stress field, borehole jack test results can be used to determine the borehole tensile strength. Knowing the orientation of the in situ stress field and the flexural strength of the rock substance, the magnitude of the in situ stress components can be calculated. The detection of very small cracks is essential for the accurate determination of the failure loads which are used in the calculation of strengths and stress components.

Van, T. K.↗

IM7/LARC(tm) MPEI-1 Polymide Composites

LARC(Trademark) MPEI-1 (Langley Research Center(Trademark) modified phenylethynyl imide-1) phenylethynyl containing aromatic polymide, is based on the reaction of biphenyl dianhydride (BPDA), 3,4'-oxydianiline (3,4'-ODA), 1,3-bis(3-aminophenoxy)benzene (APB), 2,4,6-triaminopyrimidine (TAP) and 4-phenylethynyl phthalic anhydride (PEPA), presumably resulting in a mixture of linear, branched and star shaped phenylethynyl containing imides which was evaluated as a matrix for high-performance composites. The poly(amid acid) solution of MPEI-1 in N-methypyrrolidinone was synthesized at 35% and 42% solids. Unidirectional prepreg was fabricated from these solutions and Hercules IM7 carbon fiber utilizing NASA- Langley's multipurpose prepreg machine. The temperature-dependent volatile depletion rates, thermal crystallization behavior and resin theology were characterized. Based on this information, a composite molding cycle was developed which yielded well consolidated, void-free laminates. Composite mechanical properties such as short beam shear strength, longitudinal and transverse flexural strength and flexural modulus, longitudinal tensile strength and notched and unnotched compression strengths were measured at room temperature (RT) and elevated temperatures. These mechanical properties are compared with those of IM7/LARC(Trademark) PETI-5 composites.

Hou, T. H.↗

A comparison of flexural properties of aramid reinforced pultrusions having constant fiber volume and varied matrices, pretreatments, and postcures

Aramid reinforcement composite materials of equal fiber volume having varied polymer thermoset matrices have been pultruded and flexurally tested to failure. The objective was to improve flexural properties of aramid reinforced pultrusions. Pultrusions of both sized and unsized aramid fiber with four different resin systems were compared to determine the effects of sizing compounds and post-thermal treatments on the flexural strength as an indication of fiber wettability and fiber-to-resin interface bonding. Improvements in flexural strength as the result of pretreatments with sizing solutions used in this study were marginal. The most significant improvements in flexural properties were the results of postcuring. Overall improvements ranged from a low 39,647 Psi(273 Mpa) to a high of 80,390 Psi(554 Mpa), or 103 percent. The fact that post-thermal treatments improved the flexural properties of the four pultrusions indicates that a full cure did not occur in either resin system during the pultrusion process. The increased flexural strengths of the polyester and vinyl ester pultrusions were the most surprising. Based on data presented, the most promising resin system of the four examined (VE 8300, Aropol 7430, Epon 9302, and Epon 9310) for Kevlar reinforced pultrusion is Epon 9310 epoxy.

Wilson, Maywood L.↗

Effect of Sintering Temperature on Density and Mechanical Properties of Solid-State Sintered Silicon Carbide Ceramics and Evaluation of Failure Origin

Densified silicon carbide (SiC) is prepared through dry pressing of SiC powder followed by pressureless sintering in the presence of boron carbide and carbon as the additives. Sintering of SiC parts shows the increase in density with the increase in temperature (1950-2180 °C) by resulting in higher than 98% relative density (RD) at 2150 °C and above for 1 h. Sintered specimens are evaluated concerning the phase, microstructure and mechanical properties including hardness and flexural strength. The machined surface of SiC parts with about 98% RD is studied for the origin of failure. The estimated size of critical flaws (32-110 µm) based on flexural strength and fracture toughness indicates that machining defects are one of the primary reasons for failure in SiC ceramics. The order of magnitude of defects on machined surfaces of sintered SiC by SEM studies is found to be comparable with the estimated size of critical flaws. The failure behavior of SiC is discussed with the help of Weibull statistics with respect to the variation of four-point flexural strength.

36 MATERIALS SCIENCE↗

Surface modification of bamboo fiber with sodium hydroxide and graphene oxide in epoxy composites

Bamboo fibers (BFs) have high mechanical properties and are candidate reinforcement for epoxy matrix composites. However, to improve performance, good fiber-matrix interaction is required. In this work, unidirectional long BF reinforced epoxy composites at fiber volume content of 22%, 40%, and 50% were made by compression molding. The 40 v% untreated BF reinforced composites exhibited 107% and 439% increase for flexural strength and modulus, respectively, compared to neat epoxy. Sodium hydroxide (NaOH) treatment was used to modify the surface of the BFs, and then the NaOH modified BFs were coated with graphene oxide (GO). The 40 v% NaOH modified BF composites showed an improvement from 259.9 to 327.5 MPa for flexural strength and from 16.7 to 21.5 GPa for flexural modulus, compared to 40 v% untreated BF composites. Slight improvement in properties up to 334.6 MPa for flexural strength and up to 23.8 GPa for flexural modulus was achieved for composites made of 40 v% NaOH/GO modified BF. Surface modification of BF after the NaOH and NaOH/GO treatment was confirmed by X-ray photoelectron spectroscopy and by scanning electron microscopy, which showed differences on the fiber surface morphology and on the composite fracture surface. This BF surface modification approach with GO has potential to impart other properties beyond mechanical to produce multifunctional composite and lead to the use of sustainable plant fibers as alternatives to synthetic fibers.

36 MATERIALS SCIENCE↗

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

ABSTRACT Zirconia‐toughened alumina (ZTA) ceramics with high mechanical properties were sintered by hot‐pressing method using SiC particles (SiCp) and SiC whiskers (SiCw) as the reinforcing agents simultaneously. The influences of sintering temperature, SiCp, and SiCw contents on the microstructure and mechanical properties of ZTA ceramics were investigated. It was found that both SiCp and SiCw could contribute to grain refinement significantly and promote the mechanical properties of the ceramics. However, the excess addition of SiCp or SiCw led to the formation of pores with large sizes and degraded the mechanical properties instead. When 13 wt% SiCp was introduced, the maximum flexural strength of 1180.0 MPa and fracture toughness of 15.9 MPa·m 1/2 were obtained, whereas the maximum flexural strength of 1314.0 MPa and fracture toughness of 14.7 MPa·m 1/2 were achieved at 20 wt% SiCw. Interestingly, the simultaneous addition of SiCp and SiCw could further improve the mechanical properties, and the highest flexural strength of 1334.0 MPa and fracture toughness of 16.0 MPa·m 1/2 were achieved at a SiCw/SiCp ratio of 16/4. The reinforcement mechanisms in the ceramics mainly included the phase transformation toughening of ZrO 2 , the crack deflection and bridging of SiCp and SiCw, and the pull‐out of SiCw.

Liu, Longyang↗

Understanding the effect of specimen size on the properties of fine-grain isotropic nuclear graphite for irradiation studies: Mechanical properties

Programs at Oak Ridge National Laboratory are investigating the effects of neutron irradiation in the High Flux Isotope Reactor (HFIR) on properties of fine-grain isotropic nuclear graphites. Specimens were irradiated in the HFIR flux trap, which requires using specimens that are smaller than the sizes recommended by ASTM standards. Here, this work has investigated whether subsized specimens can be used to reliably predict strength behavior. The results show that (1) tensile strength was loosely coupled to specimen volume, (2) the compression specimens had a slightly higher strength for larger volumes, (3) the uniaxial flexural strength was nearly independent of specimen effective area for one orientation whereas the other orientation showed a slight strength–size scaling Weibull behavior, and (4) equibiaxial flexural strength followed traditional strength–size scaling Weibull behavior. These results suggest that fine-grain graphite is more similar to ceramics than to medium- and large-grained graphite with respect to both the strength-limiting flaws (Griffith theory) and the effect of machining on the strength behavior. This work shows that using specimens that are smaller than ASTM recommendations are suitable for investigating the strength changes caused by neutron irradiation because the primary interest is the relative change in the strength distribution parameters rather than their absolute values.

36 MATERIALS SCIENCE↗

Reliability comparisons between additively manufactured and conventional SiC–Si ceramic composites

Abstract An additively manufactured reaction‐bonded silicon carbide ceramic composite is fabricated using a bimodal powder feedstock and the binder‐jetting printing technique. On fabricating, the ceramic is investigated to report its composition, mechanical, and thermal properties at room temperature and high temperatures (up to 750). The ceramic has a density of 2.76 g/cc, and shows a hardness of 21.74 GPa, and a flexure strength of 207.5 MPa at room temperature. The mechanical property of flexure strength is used to estimate its failure probability under applied stress, using a Weibull distribution. The mechanical properties and failure probabilities are compared with those of conventionally fabricated reaction‐bonded silicon carbide ceramics reported in the literature. These ceramics were fabricated using methods such as slip‐casting, compacting, and tape‐casting. The comparison is used to elucidate the advantages and areas of improvement of the present additive manufacturing technique for reaction‐bonded ceramics.

14 SOLAR ENERGY↗

Magnetic and mechanical properties of grain-refined Dy-free Nd-Fe-B sintered magnets

In this work, the effects of grain size on magnetic and mechanical properties of Dy-free Nd-Fe-B sintered magnets were studied. The grain size of the sintered magnets was varied by using different sized Dy-free Nd-Fe-B alloy feedstock powders which were ball milled to different extents. Increasing the ball milling time from 7 to 11 h caused the average particle size of the powders to decrease from 3.6 to 2.1 µm, while the average grain size of the corresponding sintered magnets decreased from 5.0 to 4.0 µm. The intrinsic coercivity Hcj and maximum energy product (BH) max of these magnets increased from 11.6 to 13.7 kOe and 41.6 to 43.6 MGOe, respectively. The finer grain magnets exhibited better thermal stability, as indicated by a smaller temperature coefficient of H cj (-0.71%/°C). With extending ball milling time to 15 h, the magnetic properties of the magnets deteriorate, while the flexural strengths first decrease and then increase. The flexural strength improvement is attributed to the increased Oxygen content in the magnets due to finer grains. The coercivity enhancement by reduction of grain size is a promising approach to develop Dy-free Nd-Fe-B sintered magnets with better thermal stability. It is important to control the Oxygen contents in the magnets to compromise both magnetic and mechanical properties.

36 MATERIALS SCIENCE↗

Effect of hot isostatic pressing on reaction-bonded silicon nitride

Specimens of nearly theoretical density have been obtained through the isostatic hot pressing of reaction-bonded silicon nitride under 138 MPa of pressure for two hours at 1850, 1950, and 2050 C. An amorphous phase that is introduced by the hot isostatic pressing partly accounts for the fact that while room temperature flexural strength more than doubles, the 1200 C flexural strength increases significantly only after pressing at 2050 C.

Watson, G. K.↗

Thermal effects on the mechanical properties of SiC fiber reinforced reaction bonded silicon nitride matrix (SiC/RBSN) composites

The elevated temperature four-point flexural strength and the room temperature tensile and flexural strength properties after thermal shock were measured for ceramic composites consisting of 30 vol pct uniaxially aligned 142 micron diameter SiC fibers in a reaction bonded Si3N4 matrix. The elevated temperature strengths were measured after 15 min of exposure in air at temperatures to 1400 C. Thermal shock treatment was accomplished by heating the composite in air for 15 min at temperatures to 1200 C and then quenching in water at 25 C. The results indicate no significant loss in strength properties either at temperature or after thermal shock when compared with the strength data for composites in the as-fabricated condition.

Bhatt, R. T.↗

Thermal effects on the mechanical properties of SiC fibre reinforced reaction-bonded silicon nitride matrix composites

The elevated temperature four-point flexural strength and the room temperature tensile and flexural strength properties after thermal shock were measured for ceramic composites consisting of 30 vol pct uniaxially aligned 142 micron diameter SiC fibers in a reaction bonded Si3N4 matrix. The elevated temperature strengths were measured after 15 min of exposure in air at temperatures to 1400 C. Thermal shock treatment was accomplished by heating the composite in air for 15 min at temperatures to 1200 C and then quenching in water at 25 C. The results indicate no significant loss in strength properties either at temperature or after thermal shock when compared with the strength data for composites in the as-fabricated condition.

Bhatt, R. T.↗

Effect of Carbon Fiber Surface Modification on the Mechanical Properties of Carbon-Fiber-Reinforced Ultrahigh-Molecular-Weight Polyethylene Composite

In this paper, the surface properties and morphologies of the concentrated nitric acid (HNO{sub 3})-modified carbon fiber (CF) were characterized by XPS, SEM, and contact angle goniometer, respectively. The results showed that both the oxygen-containing functional groups content and the surface roughness of concentrated HNO{sub 3}-modified CF significantly increased. The contact angle of concentrated HNO{sub 3}-modified CF was obviously lower than that of unmodified CF. Studies on the mechanical properties of carbon-fiber-reinforced ultrahigh-molecular-weight polyethylene (CF/UHMWPE) composite revealed that the stress–strain behavior gradually changed from nonlinear to linear relationship with the rise of CF content in UHMWPE matrix. Both the tensile strength and modulus increased with the rise of CF content. Conversely, as the CF content in UHMWPE matrix is increasing, the flexural strength and modulus increased first and then decreased. The flexural strength and modulus of CF/UHMWPE composite with 30 wt.% CF content reached the maximum value of 157.61 MPa and 9.82 GPa, respectively. Moreover, the CF surface modification and CF content have a synergistic effect on the tensile and flexural mechanical properties of the CF/UHMWPE composite. The influence of CF modification on the tensile and flexural mechanical properties of the composite became more and more obvious with the rise of CF content.

36 MATERIALS SCIENCE↗

Melt extruded versus extrusion compression molded glass-polypropylene long fiber thermoplastic composites

Long fiber thermoplastic (LFT) composites are processed either with extrusion compression or fiber injection processes. The properties of LFT materials are highly influenced by processing techniques, which lead to different porosity contents, fiber length distributions, and fiber orientation distributions. It is important to understand the various LFT processing techniques and their effects on mechanical, thermal, and microscopic properties. This work considered LFT sheets processed via extrusion, which offers highly aligned fibers (referred to as “Tecnogor composites”), and LFT composites produced via extrusion compression molding (ECM), which offers a random distribution of fibers. Tecnogor composites exhibited higher flexural strength (35–65%), flexural modulus (132–172%), tensile strength (39–52%), tensile modulus (67–75%), and Izod impact resistance (195–220%) than the random LFT composites. This response was attributed to the aligned fibers in Tecnogor composites. Mathematical models including Halpin-Tsai and Lavengood-Goettler were used to predict and compare the Young’s modulus of Tecnogor and ECM composites, respectively.

mechanical testing↗

Thermal shock resistance of additively manufactured alumina

The mechanical behavior and cracking patterns of thermally-shocked additively manufactured alumina were investigated. The flexural strength of test specimens that had been heated to temperatures ranging from 200°C to 1000°C and then rapidly quenched in water was determined at ambient temperature by four-point bending. Results indicated that the surface cracking patterns had a multifractal structure and that an increase in the thermal shock temperature led to an increase in the density and uniformity of the crack network. Further, the flexural strength results were analyzed with Weibull statistics, where the Weibull moduli for most of the thermal shock conditions tested were found to be statistically indistinguishable. It was also found that a significant decrease (~50%) in flexural strength occurred for heating temperatures ≥300°C. The effect of the manufacturing method on cracking patterns is discussed, as well as the implication of the material behavior for practical applications of these materials.

36 MATERIALS SCIENCE↗

Novel dense membrane for hydrogen separation for energy applications

The main objectives of this project are: (1) Characterization of the thermo mechanical properties of the novel dense HTM bulk sample; (2) Development of a correlation among the intrinsic factors (such as grain size and phase distribution), and the extrinsic factors (such as temperature and atmosphere) and the thermo-mechanical properties (such as strengths and stress) to predict the performance of a HTM system (HTM membrane and porous substrate) ; and (3) Evaluation of the stability of the novel HTM membrane and its property correlations after thermal cycling. Based on all results and analysis of the thermo mechanical properties for the HTM cermet bulk samples, several important conclusions were made. The mean σfs at room temperature is approximately 356 MPa for the HTM cermet. The mean σfs value decreases to 284 MPa as the temperature increases to 850?C. The Difference difference in atmosphere, such as air or N2, had an insignificant effect on the flexural strength values at 850?C for the HTM cermet. The HTM cermet samples at room temperature and at 500?C fractured without any significant plastic deformation. Whereas, at 850?C, the HTM cermet samples fractured, preceded by an extensive plastic deformation. It seems that the HTM cermet behaves more like an elastic material such as a nonmetal ceramic at the room temperature, and more like a ductile material at increased temperature (850?C). The exothermic peak during the TG/DTA tests centered at 600?C is most likely associated with both the enthalpy change of transformation from the amorphous phase into crystalline zirconia and the oxidation of Pd phase in HTM cermet in air. The endothermic peak centered at 800?C is associated with the dissociation of PdO to Pd for the HTM cermet sample in both inert N2 environment and air. There is a corresponding weight gain as oxidation occurs for palladium (Pd) phase to form palladium oxide (PdO) and there is a weight loss as the unstable PdO is dissociated back to Pd and oxygen. The normal stress and shear stresses from the Mohr?s circle indicate that the residual stress in the HTM cermet sample is mainly as compressive residual stress in the magnitude of -135 to -155 MP, and with very little shear stress (in the magnitude of 10 MPa). The magnitude of change in the normal stress and the shear stress is insignificant in the HTM after 120 thermal cycles. However, the principle normal stress changes from compressive to tensile residual stress and there is a significant increase in the shear stress after 500 thermal cycles. The calculated value based on the equation and the Mohr?s circle is found to be consistent with the experimental value for the as-received HTM cermet samples. At some rotation (φ) angle, the residual stress was found to be as tensile stress. Most ceramic material is weak in tension, and develops microscopic cracks. With treatment of 120 thermal cycles between 50?850?C, the HTM- sample exhibited thermally-induced cracks on the surface. Visually observable cracks appeared on the surface of HTM cermet with continuous thermal cycling, after 500 thermal cycles. The XRD powder diffraction analysis indicated an increased amount of crystalline PdO crystalline in HTM cermet after 120 and 500 thermal cycles as compare to the as-received samples. The Pd crystalline peaks were found to significantly decrease in peak intensity with thermal cycling. Higher peak intensity for PdO phase was observed with increased number of thermal cycles. A Monoclinic monoclinic zirconia phase was first identified in the as-received HTM as-received sample. However, with thermal cycling treatment of both 120 and 500 thermal cycles, the M-ZrO2 phase is transformed to the tetragonal YSZ, which is consistent with the thermal analysis results by TG/DTA. Correlations of the microstructural and thermo-mechanical properties of both selected reference material and ANL-3e HTM cermet bulk sample are affected mainly by porosity and microstructural features, such as grain size and pore size/distribution. The Young?s Modulus (E-value), especially, is positively proportional to the flexural strength for materials with similar crystallographic structure. For different crystallographic materials, physical properties such as E and density are independent of mechanical properties, such as flexural strength.. Microstructural properties, particularly, grain size and crystallographic structure, and thermodynamic properties are the main factors affecting the mechanical properties at both room and high temperatures. The oxidation and the plasticity of Pd phase mainly affect the mechanical properties of HTM cermet at high temperature or with thermal cycling treatment. Changes in the residual stress and microstructure affect the mechanical properties of HTM when subjected to high temperature or thermal cycling treatment.

08 HYDROGEN↗

Research on graphite reinforced glass matrix composites

A composite that can be used at temperatures up to 875 K with mechanical properties equal or superior to graphite fiber reinforced epoxy composites is presented. The composite system consist of graphite fiber, uniaxially or biaxially, reinforced borosilicate glass. The mechanical and thermal properties of such a graphite fiber reinforced glass composite are described, and the system is shown to offer promise as a high performance structural material. Specific properties that were measured were: a modified borosilicate glass uniaxially reinforced by Hercules HMS graphite fiber has a three-point flexural strength of 1030 MPa, a four-point flexural strength of 964 MPa, an elastic modulus of 199 GPa and a failure strain of 0.0052. The preparation and properties of similar composites with Hercules HTS, Celanese DG-102, Thornel 300 and Thornel Pitch graphite fibers are also described.

Bacon, J. F.↗

Polyimide Composites from 'Salt-Like' Solution Precursors

Four NASA Langley-developed polyimide matrix resins, LaRC(TM)-IA, LaRC(TM)-IAX, LaRC(TM)-8515 and LaRC(TM)-PETI-5, were produced via a 'saltlike' process developed by Unitika Ltd. The salt-like solutions (65% solids in NMP) were prepregged onto Hexcel IM7 carbon fiber using the NASA LaRC multipurpose tape machine. Process parameters were determined and composite panels fabricated. The temperature dependent volatile depletion rates, the thermal crystallization behavior and the resin rheology were characterized. Composite molding cycles were developed which consistently yielded well consolidated, void-free laminated parts. Composite mechanical properties such as the short beam shear strength; the longitudinal and transverse flexural strength and flexural modulus; the longitudinal compression strength and modulus; and the open hole compression strength and compression after impact strength were measured at room temperature and elevated temperatures. The processing characteristics and the composite mechanical properties of the four intermediate modulus carbon fiber/polyimide matrix composites were compared to existing data on the same polyimide resin systems and IM7 carbon fiber manufactured via poly(amide acid) solutions (30-35% solids in NMP). This work studies the effects of varying the synthetic route on the processing and mechanical properties of the polyimide composites.

Cano, Roberto J.↗