SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In TBA–water mixtures, using DSC and XRD, the eutectic temperature (-8 °C) and composition (22.5% w/w TBA) were determined.
The equilibrium compositions of all phases in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C were determined experimentally through isothermal annealing for up to 500 h and compared with currently available computational thermodynamic descriptions. Additionally, the study examined how adding a third element to the binary system affects the microstructure by analyzing changes in the volume fraction of the intermetallic phase in the eutectic region. It was observed that Nb and Ti addition lowered the intermetallic fraction in the eutectic region while Al and Cr addition did the opposite. The fraction of intermetallic phase in the eutectic region is very important because it contributes to extreme brittleness of these alloys. Also, Al, Nb and Ti addition promoted different precipitates upon annealing when added in sufficient amounts. The collected data on composition and phase equilibria provides crucial information for improving the thermodynamic assessments of the binary and ternary alloy systems.
Molten salt reactor (MSR) with Thorium (Th) fuel cycle has attracted growing attention due to its merits such as safety, low radioactive waste production, and non-proliferation. The design and safe operation of MSR rely on a thorough understanding of the thermophysical properties of molten salts over a wide range of composition and temperature. However, experimental data of Th-based molten salts are limited due to the inherent challenges of dealing with corrosive molten salts and the radioactive nature of actinides. Here, in this work, thermophysical properties including density, heat capacity, thermal expansion coefficient, and mixing energy of binary NaCl-ThCl 4 and ternary NaCl-ThCl 4 -UCl 3 molten salts are explored using ab-initio molecular dynamic simulations (AIMD) with the dDsC dispersion correction. The calculated mixing energy of binary NaCl-ThCl 4 exhibits a minimum close to the eutectic composition. The heat capacity of the mixtures is linearly dependent on the mole fraction of each component. 7-fold and 6-fold coordinated Th complexes are dominant in the mixtures. 8-fold coordinated Th complex increases with ThCl 4 fraction due to the formation of network structures. The average coordination number of Th exhibits a minimum near the eutectic composition. The minimum mixing energy for the ternary mixtures is observed in systems with a composition close to [NaCl] 0.5 [ThCl 4 ] 0.25 [UCl 3 ] 0.25 . The density positively deviates from the ideal solution in mixtures near this composition. These results are important to fill the data and knowledge gap of ThCl 4 molten salts.
Zirconium (Zr) possesses outstanding properties, including exceptional chemical resistance and a high melting point, and is therefore desirable for use in a wide variety of challenging environments, such as in nuclear reactors and the chemical processing industry. To minimize the amount of Zr required for any given application, developing methods for generating metallic Zr coatings is highly advantageous. Owing to Zr’s highly negative reduction potential, electrodeposition in traditional solvents at near ambient temperatures remains challenging and thus not well understood. Due to the extreme conditions required to deposit this metal, extensive work has been conducted in molten salt electrolytes, however the broad applicability of this methodology is limited due to its corrosivity. The primary focus of this article is to present an overview of Zr’s electrochemical behavior and to consolidate the efforts of researchers in exploring electrodeposition techniques for Zr involving aqueous, organic, ionic liquid, deep eutectic, and molten salt solvents. With this information, we highlight trends across solvent systems and opportunities for future research.
Argonne performed thermodynamic modeling to predict eutectic compositions in the LiF-NaF-UF4 and LiF-NaF ThF4 systems. Three compositions each of LiF-NaF-UF4 and LiF-NaF-ThF4 molten salts were produced and the thermal properties between 400 and 600 °C were measured. One composition from each salt system was selected for measurements of heat capacity and thermal diffusivity across temperature ranges suggested by FEI experts as beneficial to industry.
This specification covers the requirements and details for the selection, testing, cleaning, marking, shipping, inspection and installation (including welding) of the Inert Gas Subsystem, Secondary Coolant Management Subsystem, and Secondary Cover Gas Management Subsystem from the Valve Panel up to the classification division, the patch panel of the upper confinement. Including NaK, argon, eutectic gallium indium tin (eGaInSn), and helium fill tubing, valves, and hangers. These systems consist of the necessary straight lengths, elbows, reducers, fittings, tube connections, instrument taps, and valves called for by applicable drawings. All components shall be procured as ASME Section III Class 2 unless otherwise modified hereinafter. Pressure relief valves have been sized to prevent overpressure in the event there is full regulator flow. This is documented in ECAR-7365.
Thermal properties of several compositions of the binary NaCl-PuCl 3 salt were measured to confirm the eutectic composition and provide high quality data for use by MSR developers. The PuCl 3 was generated by reducing PuO 2 to plutonium metal in the presence of calcium metal and then chlorinating the metallic plutonium with NH 4 Cl. The resulting PuCl 3 was used to make seven binary NaCl-PuCl 3 compositions with between 59.9 mol % PuCl 3 (Salt 1) and 20.0 mol % PuCl 3 (Salt 7). The eutectic temperature was measured to be 457 ± 4 °C by onset determination in DSC analyses of the seven mixtures, which is consistent with the values in the literature. Additional transitions were observed at approximately 332 and 363 °C in analyses of the PuCl 3 -rich compositions (Salts 1-3) at about 376 and 439 °C in analyses the Na-rich compositions (Salts 4-7). The solid state heat capacity decreased with increasing PuCl 3 content. The liquid state heat capacity was measured for Salt 3 (37.4 mol % PuCl 3 ) and Salt 4 (38.3 mol % PuCl 3 ). A higher heat capacity was measured for Salt 4 and measurements with both salts showed a positive correlation with temperature between 520 and 730 °C. Cells fabricated from nickel and molybdenum for use in DSC measurements at high temperatures could not be adequately sealed because these materials are not sufficiently malleable, even after high temperature annealing. It is recommended that future development focus on corrosion-resistant materials that have mechanical and thermal properties similar to the commercially available gold cells, such as Pt-Rh (80–20) and pure platinum. Those materials are chemically inert, soft, and malleable like gold, but have melting temperatures higher than 1000 °C (Rakhtsaum, 2013). Use of the Pt-Rh alloy should be evaluated first based on superior machinability for making precision parts and its current use in commercial DSC high temperature crucibles. The commercial Pt-Rh cells are not hermetically sealable, but it is expected that cells made from thinner stock can be sealed.
This study aimed to determine the structure–function relationship (SFR) for ChCl–glycerol mixtures, a deep eutectic solvent (DES), by investigating their microscopic solvation dynamics and how it relates to their macroscopic properties across varying concentrations of ChCl. Femtosecond transient absorption (fs-TA) spectroscopy revealed two distinct solvation dynamics time constants: τ 1 , governed by glycerol–glycerol interactions, and τ 2 , dominated by the choline response. The τ 2 minimum at 25–30 mol % ChCl closely aligned with the eutectic composition (~33.33 mol % ChCl), where the glycerol network was the most organized and the choline ions exhibited the fastest relaxation. The viscosity decreased sharply up to ~25 mol % ChCl and then plateaued, while the conductivity increased monotonically with ChCl concentration, reflecting enhanced ionic mobility. The density decreased with both increasing ChCl concentration and temperature, indicating disrupted hydrogen bonding and reduced molecular packing. The polarity, measured using betaine-30 (B30) and the E T (30) polarity scale, increased steeply up to approximately 25 mol % ChCl before reaching a plateau. These findings identified the eutectic composition as the optimal concentration range for balancing stability, fluidity, conductivity, and enhanced dynamics within the glycerol system.
High-temperature Thermal Energy Storage (TES) has drawn great attention as a technology that can increase the role and profitability of micro nuclear reactors in the decentralized clean energy market. Various research needs have been proposed by Idaho National Laboratory (INL) in "the Integrated Energy Systems: 2020 Roadmap" with the goal of utilizing the high temperature of 550 degrees or more generated in the 4th generation reactor to industrial purposes from the standpoint of integrated energy systems [1]. With the recent development of the 4th generation nuclear power plant, including micro nuclear reactor, there is a great deal of interest in researching how to efficiently couple a heat source to an industrial process through thermal processing. Texas A&M University (TAMU) and INL are currently collaborating to develop a novel latent heat storage design called HITB (Heat pipe-Integrated Thermal Battery). As part of the small-scale experimental demonstration research for HITB, a study for storage medium selection was conducted at TAMU. Eutectic salts have attracted interest as high-temperature heat storage medium for HITB. Especially, chloride molten salts and fluoride molten salts are considered promising candidates due to their high melting temperature, thermal stability, and high latent heat of fusion. Since eutectic salts have poor thermal conductivity in general, it is critical to distribute materials with high thermal conductivity evenly to facilitate the charging and discharging of heat. In this study, metal foam was considered in the HITB system to overcome the poor heat transfer characteristics of eutectic salts. In order to improve heat transfer, it is necessary to study materials with high thermal conductivity, corrosion resistant to molten salts, such as fins, extended surfaces, particles, microcapsulation, or foam structure. Porous structure of copper or aluminum can increase heat transfer area, form a thermal transfer network, and increase the effective thermal conductivity of thermal storage medium [2]. Since the melting temperature is required to be at least 450? in the current HITB design, various eutectic salts are being considered. FLiNaK and FLiBe, which are famous for fluoride salts, are good candidates, but due to the sharp rise in the price of LiF recently, they are excluded for economic reasons to be applied to large-capacity thermal energy storage. On the other hand, chloride salts are very cheap and easy to obtain, have a high melting temperature, and have a high latent heat of fusion, so they are recently in the spotlight as a phase change material. However, because of the hygroscopic nature of chloride salts, HCl gas due to impurity is easy to be released and is particularly vulnerable to corrosion. Chloride eutectic salts have been tested and suggested for metal alloys that are particularly resistant to corrosion, such as SS304, SS316, Hastelloy, Inconel 625, Incoloy 800H, which has low thermal conductivity, and is very expensive [3-6]. Porous materials with high thermal conductivity such as copper and aluminum have been tested for stability in fluids such as paraffin or water as metal foam or metal fin structures, but high temperature corrosion tests were not performed on various eutectic salts yet. Therefore, this study investigated the high temperature corrosion characteristics of metal alloys, such as C10100 foam, C10100 plate, 6101 alloy foam, and SS316 plate, while immersed in the candidate eutectic salts. A total of 20 tests for SS316 coupons and 10 tests for C10100 coupons were performed to ensure the repeatability of the present measurements. Since it is difficult to completely remove the salt inside metal foam due to the complex inner structure of the metal foam, only the surface condition was observed with a microscopy and scanning electron microscopy (SEM) image, except for measuring the corrosion rate and average mass loss.
Aluminum-based Al–Si alloys are widely used as phase change materials (PCMs) in thermal energy storage (TES) systems owing to their high volumetric latent heat and superior thermal conductivity. However, their long-term reliability is limited by degradation processes that remain insufficiently understood. In this work, we employ a multimodal, correlative characterization framework to systematically resolve the degradation behavior of eutectic Al–Si PCMs in contact with SS304 containers under repeated thermal cycling. By integrating high-resolution electron microscopy, three-dimensional X-ray fluorescence (3D XRF) imaging, and differential scanning calorimetry (DSC), we directly link spatially resolved compositional and microstructural evolution to changes in thermophysical properties. The correlative analysis reveals that elemental leaching of Fe, Cr, and Ni from the stainless-steel container into the PCM drives the formation of intermetallic compounds (IMCs) both at the interface and within the bulk PCM, leading to pronounced compositional heterogeneity. These interfacial reactions and diffusion-induced transformations progressively destabilize the Al–Si eutectic, reducing the effective phase-transforming fraction. Consistent with these observations, DSC measurements show a decrease in melting temperature and latent heat of fusion with thermal cycling. These results underscore the critical influence of interfacial reactions and material compatibility on the stability, durability, and overall performance of Al–Si-based TES systems.
The heat transfer rate of magnetocaloric regenerators is a topic of extensive research and the cyclability of these regenerators is critical to the operation of systems with a high coefficient of performance (e.g., potentially >22, significantly higher than typical vapor compression cooling technologies). To enable a high operating frequency that will result in a high specific cooling power, the heat transfer fluid should have high thermal conductivity and lower specific heat, i.e., higher thermal diffusivity. Eutectic metal alloys possess these qualities, such as gallium–indium–tin (Galinstan), whose thermal diffusivity has been found to be approximately an order of magnitude higher than water. For this study, the effects of eutectic liquid Galinstan exposure on the phase stability of LaFe13−x−yMnxSiyH1.6 magnetocaloric powders in an active magnetic regenerator device were investigated. The powders were characterized before and after exposure to Galinstan using X-ray diffraction, in which the phases were determined using the Rietveld refinement technique and X-ray fluorescence. It was found that after Galinstan exposure, hydrogen containing phases were present in the powder, suggesting that the hydrogen was lost from the magnetocaloric phase. The magnetocaloric phase degradation indicates that the powder was incompatible with the Galinstan metal in an environment with moisture.
Advancing the batteries is pivotal to propelling our society toward a sustainable, electrified future. The stability of electrolytes forms the backbone of energy storage systems. This is particularly the case for redox flow batteries (RFBs). Their deployability depends on their longevity and dependability. The presence of unstable electrolytes can trigger undesirable reactions, degrade performance, and lead to battery failure. Aqueous electrolytes, with limited electrochemical stability window (ESW), are prone to hydrogen and oxygen evolution. Conversely, non-aqueous electrolytes offer enhanced stability. In this study, we unveil the ESW of a non-aqueous eutectic solvent, comprising choline fluoride and ethylene glycol—a composition that has eluded experimental investigation until now. Our findings show that the stability window, reduction and oxidation potential limits of deep eutectic solvents, are sensitive to variations in the halide component of the ammonium salt. Furthermore, this work not only highlights the benefits of novel deep eutectic solvents but also sets the stage for their strategic use in future battery electrolytes.
Carbon dioxide (CO 2 ) emissions from fossil fuel combustion are a significant source of greenhouse gas, contributing in a major way to global warming and climate change. Carbon dioxide capture and sequestration is gaining much attention as a potential method for controlling these greenhouse gas emissions. Among the environmentally friendly solvents, deep eutectic solvents (DESs) have demonstrated the potential capability for carbon capture. To establish a theoretical framework for DES activity, thermodynamics modeling and solubility predictions are significant factors to anticipate and understand the system behavior. Here, in this study, we combine the COSMO-RS model with machine learning techniques to predict the solubility of CO 2 in various deep eutectic solvents. A comprehensive data set was established comprising 1973 CO 2 solubility data points in 132 different DESs at a variety of temperatures, pressures, and DES molar ratios. This data set was then utilized for the further verification and development of the COSMO-RS model. The CO 2 solubility (ln(x CO 2 )) in DESs calculated with the COSMO-RS model differs significantly from the experiment with an average absolute relative deviation (AARD) of 23.4%. A multilinear regression model was developed using the COSMO-RS predicted solubility and a temperature-pressure dependent parameter, which improved the AARD to 12%. Finally, a machine learning model using COSMO-RS-derived features was developed based on an artificial neural network algorithm. The results are in excellent agreement with the experimental CO 2 solubilities, with an AARD of only 2.72%. The ML model will be a potentially useful tool for the design and selection of DESs for CO 2 capture and utilization.
In this work, we established a novel deep eutectic solvent (DES) using lignin-derived guaiacol as hydrogen bond donor (HBD). The sole ChCl/guaiacol system was found to be inefficient for the fractionation of wheat straw (WS), while the incorporation of trace AlCl 3 significantly facilitated the degradation of hemicellulose and lignin, resulting in a complete enzymatic digestibility of the pretreated WS. Further, this study revealed that the DES-degraded lignin was readily precipitated during the washing process, and thus hindered the enzymatic hydrolysis of poplar and bamboo (with hydrolysis yield of 42.03% and 71.67%, respectively). Alkali washing offers a possible approach to remove the precipitated lignin, after which a near 100% hydrolysis yield was also obtained for poplar and bamboo.
An experimental study was performed with the objective of investigating and characterizing a dry technique for deactivation of sodium metal in a molten salt system. The study was performed in three parts. First, proof-of-principle testing of the technique was performed at bench scale. It involved loading and melting tens of grams of clean sodium metal atop a pool of LiCl-KCl-CsCl eutectic at ∼300°C and then adding ammonium chloride particles while mixing. The ammonium chloride reacted with sodium to form sodium chloride and nitrogen/hydrogen off-gases. The sodium chloride assimilated into the salt pool, forming a quaternary salt mixture of LiCl-KCl-CsCl-NaCl. The proof-of-principle testing repeatedly exhibited complete deactivation of the loaded sodium metal. Second, characterization of a LiCl-KCl-CsCl-NaCl system was performed using differential scanning calorimetry to produce a partial phase diagram of LiCl-KCl-CsCl eutectic versus NaCl, which identified the liquidus, solidus, and two-phase regions of the quaternary system. Third, the dry deactivation technique was demonstrated at kg-scale in an inert atmosphere radiological glovebox with sodium metal that was previously separated in the same glovebox from uranium metal in unirradiated blanket elements for the Fermi-1 nuclear reactor. The quaternary salt product at the end of the demonstration was sampled and showed complete deactivation of the sodium metal. Here, in short, this study qualified a technique to completely deactivate batches of sodium metal in the absence of air or water. While this study focused on the deactivation of sodium metal, including bond sodium from unirradiated blanket elements, the technique is applicable to other sources of sodium metal, such as sodium metal from batteries. Furthermore, the technique could also be extended to other alkali metal systems, including lithium, sodium, potassium, rubidium, cesium, and mixtures thereof.
This report outlines the progress of Idaho National Laboratory in developing a high-fidelity and high-resolution model of the Microreactor Applications Research Validation and Evaluation reactor. The model was developed under the Nuclear Energy Advanced Modeling and Simulation microreactor application driver at Idaho National Laboratory. The overarching objective of this activity is the development of a high-fidelity multiphysics MARVEL model using NEAMS tools, and to verify and validate NEAMS tools against MARVEL reference simulation and experimental data, respectively. This is a unique opportunity to conduct multiphysics analysis on a soon-to-be-deployed microreactor. This multiphysics model developed under the NEAMS-funded INL microreactor application driver leverages three single-physics models coupled via the MOOSE’s MultiApp and Transfer systems. The latter systems enable in-memory data transfer between MOOSE-based and MOOSE-wrapped applications. The first single-physics model, that functions as main application, leverages Griffin to model the neutron transport in the core through the discontinuous finite element (DFEM) discrete ordinates solver (SN). Several optimization flags that were developed by the Griffin developer team were beta-tested to enhance the solver’s performance. These include the combined use of using_average_xs and update_averaged_xs_on that enable to avoid expensive on-the-fly cross sections evaluations at each linear iterations in favor of evaluations of the macroscopic cross sections at each Picard iteration. The second single-physics model uses BISON to handle solid heat transfer and asymptotic hydrogen redistribution analysis in the fuel. While the model returns consistent results for the temperature and hydrogen distribution in the fuel, a mismatch was noticed in the calculated temperature in the reflector due to the value of the gap conductance used in our model. Ongoing investigations are being performed to assess the origin of this discrepancy. Finally, the System Analysis Module (SAM) was used to model the flow of the sodium-potassium eutectic in the primary loop. A first verification was also performed showing good agreement in terms of mass flow rate and inlet temperature. All mesh files were generated using the MOOSE Reactor module, removing the need for external meshing tools. Notably, this workscope represents one of the initial applications of the MOOSE Reactor module for modeling highly irregular geometries. The use of the reactor module significantly streamlined the mesh generation process. The full multiphysics mode, that combines all the single physics models, was leveraged to conduct initial steady-state multiphysics simulations to compute power, and temperature distribution in the reactor. Initial testing was performed for transient simulations as well. In this case, the new checkpoint restart capability for eigenvalue calculations was tested showing the capability for streamlined restart of transient calculations. Future work will focus on improving the fidelity of the model by performing comprehensive code-to-code comparisons. For instance, the full-core Griffin neutronics model will be benchmarked against MCNP reference results, that were provided by the MARVEL design team. Additionally, the SAM T/H model will be verified against reference RELAP-5 results for selected accident scenarios. Besides code-to-code verification exercises, the model fidelity will be improved by replacing the single-channel SAM model with a more complex SAM-Pronghorn coupled model, in which the sub-channel capability is deployed to obtain radial temperature resolution in the coolant. This model will be developed in synergy with the NEAMS thermal hydraulics team.
This report outlines the progress of Idaho National Laboratory (INL) in improving the fidelity of the multiphysics model of the Microreactor Applications Research Validation and Evaluation (MARVEL) reactor developed in FY24. The multiphysics model firstly developed in FY24 leverages three single-physics models coupled via the MOOSE’s MultiApps and Transfer systems. The first single-physics model, that functions as the driver application, leverages Griffin to model the neutron transport in the core through the discontinuous finite element (DFEM) discrete ordinates solver (SN). The second single-physics model uses BISON to compute the solid temperature in the reactor. Finally, the System Analysis Module (SAM) was used to model the flow of the sodium-potassium eutectic in the primary loop. In this report we detail the following improvement and enhancements: • An updated mesh leveraging the latest feature in the reactor module (see Section 3.1.).
Understanding the influences of proton sharing and hydrogen transfer in amine and hydroxyl functionalized eutectic solvents is important for tuning CO 2 binding as they relate to the chemisorption capacity and energetics of solvent regeneration in carbon capture. In this study, we examine how the CO 2 binding mechanism and energetics vary in eutectic solvents composed of choline-based hydrogen-bond acceptors (HBAs) with amine and hydroxyl moieties and ethylene glycol (EG), propylene glycol (PG), 1,2-butanediol (BD), and monoethanolamine (MEA)-type hydrogen-bond donors (HBDs), through absorption–desorption experiments and spectral analysis, supported with density functional theory (DFT) calculations. While the HBD-CO 2 complex is the major and the thermodynamically more favored product of absorption in all of the examined eutectic solvents, this complexation is only possible proceeding a proton transfer from HBD to the HBA in diol-based systems (EG, PG, BD). The interplay between HBA-CO 2 and HBD-CO 2 speciation is governed by the HBD concentration, basicity, and steric effects, with increased HBD-CO 2 interactions in the presence of smaller HBDs (size: BD > PG > EG). On the other hand, in MEA-based systems, CO 2 readily binds to the amine followed by a proton transfer from the amine to the HBA as confirmed by DFT calculations. In this way, the MEA-CO 2 chemisorption capacities exceeded that of the conventional amine (up to 0.93 mol of CO 2 per mol of MEA versus 0.5). Furthermore, the increase in CO 2 capacities and enhanced binding in eutectics including MEA or the more basic HBAs also resulted in regeneration temperatures of 70 to 60 °C with calculated reaction energies of −82 to −57 kJ/mol, compared to 50 °C for others with weaker binding, following CO 2 absorption at 25 °C.