Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Error cancellation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Dynamic Characterization of Galfenol

A novel and precise characterization of the constitutive behavior of solid and laminated research-grade, polycrystalline Galfenol (Fe81:6Ga18:4) under under quasi-static (1 Hz) and dynamic (4 to 1000 Hz) stress loadings was recently conducted by the authors. This paper summarizes the characterization by focusing on the experimental design and the dynamic sensing response of the solid Galfenol specimen. Mechanical loads are applied using a high frequency load frame. The dynamic stress amplitude for minor and major loops is 2.88 and 31.4 MPa, respectively. Dynamic minor and major loops are measured for the bias condition resulting in maximum, quasi-static sensitivity. Three key sources of error in the dynamic measurements are accounted for: (1) electromagnetic noise in strain signals due to Galfenol's magnetic response, (2) error in load signals due to the inertial force of fixturing, and (3) time delays imposed by conditioning electronics. For dynamic characterization, strain error is kept below 1.2 % of full scale by wiring two collocated gauges in series (noise cancellation) and through lead wire weaving. Inertial force error is kept below 0.41 % by measuring the dynamic force in the specimen using a nearly collocated piezoelectric load washer. The phase response of all conditioning electronics is explicitly measured and corrected for. In general, as frequency increases, the sensing response becomes more linear due to an increase in eddy currents. The location of positive and negative saturation is the same at all frequencies. As frequency increases above about 100 Hz, the elbow in the strain versus stress response disappears as the active (soft) regime stiffens toward the passive (hard) regime.

Dynamic sensing↗
NASA NTRS1989

Effects of desired signal on the performance of a sidelobe canceller

The performance of a sidelobe canceller is studied in a communication system where the desired signal is continually present and its amplitude in the auxiliary antennas may be large (above thermal noise). In such a system, to avoid the cancellation of the desired signal, one can use a reference signal and adjust the auxiliary antenna weights to minimize the error between the reference signal and the sidelobe canceller output or one can use a steering vector. It is shown that in spite of the reference signal or a steering vector, the presence of the desired signal in the auxiliary antennas degrades the interference suppression provided by a sidelobe canceller. The amount of degradation depends on the number of degrees of freedom, the strength of the various signals, and the angular resolution of the auxiliary antenna array. Signal scenarios involving a single interfering signal as well as those involving multiple interfering signals are considered.

Gupta, Inder J.↗
DOE OSTI2026

The Ghost Collider: An Innovative Higgs Factory

The Ghost Collider is an innovative proposal for a 550 GeV centre-of-mass, 275 GeV per beam linear collid-er with four interaction regions, each with the design luminosity. The primary innovation is the use of “ghost bunches” containing equal numbers of electrons and posi-trons so they are electrically neutral. In the linacs, energy is transferred between electrons and positrons in the same bunch, decelerating one type of particle and using the energy to accelerate the other: a new class of Energy Re-covery Linacs. At the interaction points, collisions be-tween two neutral ghost bunches occurs with weakened electromagnetic interaction such as the beam-beam effect or disruption, ensuring that the particles and their energy can be recycled with minimal loss. Four “serial IPs” are incorporated, where chromatic errors produced in one IP are cancelled in the following IP. The neutral beam insta-bility at the IP is also addressed. All interaction points have the nominal luminosity per IP of 2.8 x 1034 cm-2s-1 for a facility luminosity of 1.1 x1035 cm-2s-1 @ 100 MW electrical power for the RF systems. The result is a totally original concept for an electron-positron collider.

Hutton, A. [Thomas Jefferson National Accelerator ↗
NASA NTRS1985

The effect of bond functions on dissociation energies

The procedure employing bond functions recently suggested by Wright and Buenker has been applied to the N2 X 1 Sigma g + potential curve within the CAS SCF + MRSD CI treatment of electron correlation. The basis set used herein is identical to that employed by these authors in their SCF + CI calculations. The De and and the shape of the resulting potential curve, as judged by the computed vibrational levels, is not so accurate as would be expected from the results reported by Wright and Buenker (1984). The results indicate that using the CI superposition errors associated with bond functions to cancel basis set incompleteness depends on the treatment of the electron correlation.

Bauschlicher, C. W., Jr.↗
NASA NTRS1991

Office of Space Flight standard spaceborne Global Positioning System user equipment project

The Global Positioning System (GPS) provides users autonomous, real-time navigation capability. A vehicle equipped with GPS user equipment can receive and process signals transmitted by a constellation of GPS satellites and derive from the resulting measurements the vehicle's position and velocity. Specified accuracies range from 16 to 76 meters and 0.1 to 1.0 meters/second for position and velocity, respectively. In a rendezvous and docking scenario, the use of a technique called relative GPS can provide range and range rate accuracies on the order of 1 meter and 0.01 meters/second, respectively. Relative GPS requires both vehicles to be equipped with GPS user equipment and a data communication link for transmission of GPS data and GPS satellite selection coordination information. Through coordinated satellite selection, GPS measurement errors common to both users are cancelled and improved relative position and velocity accuracies are achieved. The background, the design approach, the expected performance and capabilities, the development plan, and the project status are described. In addition, a description of relative GPS, the possible GPS hardware and software configurations, and its application to automated rendezvous and capture are presented.

Saunders, Penny E.↗
NASA NTRS1992

Ulysses navigation at Jupiter encounter

The Ulysses spacecraft encountered Jupiter in February 1992, to provide a gravity assist for its prime mission over the poles of the sun. Orbit determination performed before the nominal final targeting maneuver resulted in the maneuver being cancelled. A surprisingly large Jupiter ephemeris error resulted in a slightly different encounter than planned, but one still meeting requirements. In an accompanying experiment, an alternative method of processing two-way range data was demonstrated, showing that orbit solutions obtained from only range and Doppler data can approach the accuracy of solutions based on Very Long Baseline Interferometry, range and Doppler data. Post-encounter reconstruction of the spacecraft orbit shows that the Jupiter-relative position of the spacecraft is known to within 3 kilometers, and that the Jupiter ephemeris at the time of encounter has an uncertainty of 11, 12, and .8 kilometers in the transverse, normal, and radial directions relative to Jupiter's orbit plane.

Mcelrath, Timothy P.↗
NASA NTRS1993

Comparison of methods for calibrating AVIRIS data to ground reflectance

We are comparing three basic methods of calibrating AVIRIS data to ground reflectance: (1) atmospheric radiative transfer models with the solar flux can be used to calibrate AVIRIS radiance data (Specific methods include the University of Colorado CSES ARP and ATREM algorithms); (2) Robert Green's modified MODTRAN and AVIRIS radiance model (This method is similar to 1 but differs in that the solar radiance is bypassed, so any errors in the solar flux are canceled, too); and (3) ground calibration using known sites in the AVIRIS scene. We are using 1992AVIRIS data over Cuprite, Nevada, and Blackhawk Island, Wisconsin, as our test scenes. Both these sites have extensive field measurements. The Cuprite site had a very clear atmosphere, thus path radiance was dominated by Rayleigh scattering with little or no flux beyond 1 micron. The Blackhawk site has more aerosols, with significant path radiance flux beyond 2 micron.

Clark, Roger N.↗
NASA NTRS1989

Method of resolving radio phase ambiguity in satellite orbit determination

For satellite orbit determination, the most accurate observable available today is microwave radio phase, which can be differenced between observing stations and between satellites to cancel both transmitter- and receiver-related errors. For maximum accuracy, the integer cycle ambiguities of the doubly differenced observations must be resolved. To perform this ambiguity resolution, a bootstrapping strategy is proposed. This strategy requires the tracking stations to have a wide ranging progression of spacings. By conventional 'integrated Doppler' processing of the observations from the most widely spaced stations, the orbits are determined well enough to permit resolution of the ambiguities for the most closely spaced stations. The resolution of these ambiguities reduces the uncertainty of the orbit determination enough to enable ambiguity resolution for more widely spaced stations, which further reduces the orbital uncertainty. In a test of this strategy with six tracking stations, both the formal and the true errors of determining Global Positioning System satellite orbits were reduced by a factor of 2.

Councelman, Charles C., III↗
NASA NTRS1991

Hubble Extra Solar Planet Interferometer

This paper describes a proposed third-generation Hubble instrument for extra-solar planet detection, the Hubble Extra-Solar Planet Interferometer (HESPI). This instrument would be able to achieve starlight cancellation at the 10 exp 6 to 10 exp 8 level, given a stellar wavefront with phase errors comparable to the present Hubble telescope wavefront. At 10 exp 6 starlight cancellation, HESPI would be able to detect a Jupiter-like planet next to a star at a distance of about 10 parsec, for which there are about 400 candidate stars. This paper describes a novel approach for starlight suppression, using a combination of active control and single-mode spatial filters, to achieve starlight suppression far below the classical limit set by scattering due to microsurface imperfections. In preliminary lab experiments, suppression by a factor of 40 below the classical scatter limit due to optical wavefront errors has been demonstrated.

Shao, M.↗
NASA NTRS1992

Coarse-fine residual gravity cancellation system with magnetic levitation

Aircraft flight along parabolic trajectories have been proposed and executed in order to achieve low cost, near free fall conditions of moderate duration. This paper describes a six degree of freedom experiment isolation system designed to cancel out residual accelerations due to mechanical vibrations and errors in aircraft trajectory. The isolation system consists of a fine motion magnetic levitator whose stator is transported by a conventional coarse motion stage. The levitator uses wide gap voice coil actuators and has the dual purpose of isolating the experiment platform from aircraft vibrations and actively cancelling residual accelerations through feedback control. The course motion stage tracks the levitated platform in order to keep the levitator's coils centered within their matching magnetic gaps. Aspects of system design, an analysis of the proposed control strategy and simulation results are presented. Feasibility experiments are also discussed.

Salcudean, S. E.↗
NASA NTRS1976

Improvements in navigation resulting from the use of dual spacecraft radiometric data

If two spacecraft lying along similar geocentric lines-of-sight are simultaneously tracked by two nearby ground stations (dual spacecraft two-station tracking), navigational capabilities may be substantially improved. A thorough accuracy analysis study of dual spacecraft tracking using simulated tracking data based on the trajectories of Viking and Mariner Jupiter-Saturn '77(MJS '77) missions has been carried out. Results of the study reveal the following advantages: (1) cancellation of platform parameter and transmission media modelling errors in short arc solutions, (2) accurate encounter guidance for the trailing spacecraft, (3) reduction of total tracking time requirements, and (4) rapid determination of the orbit following a maneuver on either spacecraft. It is shown that dual spacecraft data types can improve navigational capabilities by a factor of 5 to 10, under the conditions of small angular separation (not exceeding 3 degrees) of the two spacecraft and well determined trajectory of the reference spacecraft. The research to carry out and the data to obtain before the new technique can be used in interplanetary navigation are pointed out.

Chao, C. C.↗
NASA NTRS1977

Improvements in navigation resulting from the use of dual spacecraft radiometric data

When two interplanetary spacecraft lie along similar geocentric lines-of-sight, navigational advantages may be achieved by navigating one spacecraft with respect to the other. Opportunities to employ this technique will become more common as more multiprobe missions are launched. The two Viking spacecraft and the two Mariner Jupiter/Saturn '77 spacecraft will be within two and three degrees of each other, respectively, for a large portion of their missions. Results of simulated analysis as well as the processing of real tracking data from the two Viking spacecraft reveal the following advantages of the dual spacecraft navigation technique: (1) cancellation of platform parameter and transmission media modeling errors in short arc solutions, (2) accurate encounter guidance for the trailing spacecraft, (3) reduction of total tracking requirements, and (4) rapid determination of the orbit following a maneuver on either spacecraft.

Chao, C. C.↗
NASA NTRS2006

Cassini-Huygens Maneuver Experience: Second Year of Saturn Tour

This paper documents the maneuver experience during the second year of the Cassini-Huygens mission at Saturn. Since Saturn arrival in July 2004, the Cassini orbiter has made many flybys of Titan and Saturn's icy satellites. From August 2005 to June 2006, there were 39 planned maneuvers designed to target Cassini to aimpoints near Titan, Hyperion, Dione, and Rhea. Highlights of this paper include maneuver designs and strategies, maneuver performance, maneuver cancellation rationales, and a new maneuver execution-error model based on maneuvers executed to date.

navigation↗
NASA NTRS2008

Flyby Error Analysis Based on Contour Plots for the Cassini Tour

The maneuver cancellation analysis consists of cost contour plots employed by the Cassini maneuver team. The plots are two-dimensional linear representations of a larger six-dimensional solution to a multi-maneuver, multi-encounter mission at Saturn. By using contours plotted with the dot product of vectors B and R and the dot product of vectors B and T components, it is possible to view the effects delta V on for various encounter positions in the B-plane. The plot is used in operations to help determine if the Approach Maneuver (ensuing encounter minus three days) and/or the Cleanup Maneuver (ensuing encounter plus three days) can be cancelled and also is a linear check of an integrated solution.

Stumpf, P. W.↗
DOE OSTI2026

Noise-canceling quantum feedback: Non-Hermitian dynamics with applications to state preparation and magic state distillation

Time-continuous quantum measurement allows for the tracking of a quantum system in real time via sequences of short, and individually weak, measurement intervals. Such measurements are necessarily invasive, imparting backaction to the system, and allowing the observer to update their state estimate based on stochastic measurement outcomes. Feedback control then involves real-time interventions by an observer, conditioned on the time-continuous measurement signal that they receive. Here, we consider here diffusive quantum trajectories and focus on the “noise-canceling” subset of feedback protocols that aim to minimize the degree of stochasticity in the dynamics. We derive such a class of feedback operations, showing that under the idealized assumptions of pure states, unit measurement efficiency, and zero time delay in implementing feedback operations, perfectly noise-canceling feedback always exists. We consider the resulting noise-canceled dynamics generated by an effective non-Hermitian Hamiltonian; while non-Hermitian Hamiltonians from continuous monitoring generally describe rare dynamics (accessible by costly postselection), the use of noise-canceling feedback here leads to non-Hermitian dynamics that occur deterministically. We demonstrate this via examples of entangled state preparation and stabilization. We then illustrate the potential for the application of noise cancellation to boost success rates in magic state distillation protocols. We show that adding feedback based on noise cancellation into a time-continuous five-to-one distillation protocol leads to higher probabilities of successful distillation across a range of input errors and increases the threshold on input errors for which the protocol is effective. Our results highlight the efficacy of noise-canceling feedback-aided protocols for quantum state preparation and stabilization tasks.

Karmakar, Tathagata [University of California, Ber↗
NASA NTRS2019

Polar Coding For Forward Error Correction In Space Communications With LDPC Comparisons

With the surging development of optical telecommunicationsfor space applications, the importance of errorcorrection has become more apparent than ever. Specifically,the exploration of forward error correction code (FEC) methodologieswill be instrumental in developing the standards foroptical communications in space. Despite the widespread useof low-density parity-check (LDPC) codes, alternate FEC codessuch as polar codes have shown immense promise in assistingspace communications error correction with their ability tobypass the error floors that plague LDPC codes. Extremelypromising techniques including cyclic redundancy checks (CRC),successive cancellation (SC), and successive cancellation lists(SCL) that assist polar coding in achieving the Shannon limitin a timely manner are evaluated. MATLAB simulations areconducted with AWGN and burst noise to test each technique'sability to handle noise typically encountered in space and eachtechnique's ability to correct unexpected errors. Results ofsimulations for different rates and message lengths are alsoreported to determine each technique's ability to handle largedata volumes and fix errors. Similar simulations are conductedfor LDPC codes with additional tests for convolutional and nointerleavers. Finally, a discussion regarding the future ability ofpolar codes to satisfy current missions in the place of, or inconjunction with, LDPC codes along with the merits of eachFEC technique's ability to process data efficiently and handledata while maintaining adequate performance will be provided.Preliminary recommendations will be made for each technique'seffectiveness for GEO related missions along with discussionsregarding each technique's ability to fit within the CCSDS standards for optical communications.

Polar Coding↗
NASA NTRS2023

Satellite Remote-Sensing Capability to Assess Tropospheric-Column Ratios of Formaldehyde and Nitrogen Dioxide: Case Study During the Long Island Sound Tropospheric Ozone Study 2018 (LISTOS 2018) Field Campaign

Satellite retrievals of tropospheric-column formaldehyde (HCHO) and nitrogen dioxide (NO 2 ) are frequently used to investigate the sensitivity of ozone (O 3 ) production to emissions of nitrogen oxides and volatile organic carbon compounds. This study inter-compared the systematic biases and uncertainties in retrievals of NO 2 and HCHO, as well as resulting HCHO–NO 2 ratios (FNRs), from two commonly applied satellite sensors to investigate O 3 production sensitivities (Ozone Monitoring Instrument, OMI, and TROPOspheric Monitoring Instrument, TROPOMI) using airborne remote-sensing data taken during the Long Island Sound Tropospheric Ozone Study 2018 between 25 June and 6 September 2018. Compared to aircraft-based HCHO and NO 2 observations, the accuracy of OMI and TROPOMI were magnitude-dependent with high biases in clean environments and a tendency towards more accurate comparisons to even low biases in moderately polluted to polluted regions. OMI and TROPOMI NO 2 systematic biases were similar in magnitude (normalized median bias, NMB = 5 %–6 %; linear regression slope ≈ 0.5–0.6), with OMI having a high median bias and TROPOMI resulting in small low biases. Campaign-averaged uncertainties in the three satellite retrievals (NASA OMI; Quality Assurance for Essential Climate Variables, QA4ECV OMI; and TROPOMI) of NO 2 were generally similar, with TROPOMI retrievals having slightly less spread in the data compared to OMI. The three satellite products differed more when evaluating HCHO retrievals. Campaign-averaged tropospheric HCHO retrievals all had linear regression slopes ∼0.5 and NMBs of 39 %, 17 %, 13 %, and 23 % for NASA OMI, QA4ECV OMI, and TROPOMI at finer (0.05° x 0.05°) and coarser (0.15° x 0.15°) spatial resolution, respectively. Campaign-averaged uncertainty values (root mean square error, RMSE) in NASA and QA4ECV OMI HCHO retrievals were ~9.0 x 10 15 molecules cm –2 (∼ 50 %–55 % of mean column abundance), and the higher-spatial-resolution retrievals from TROPOMI resulted in RMSE values ∼30 % lower. Spatially averaging TROPOMI tropospheric-column HCHO, along with NO 2 and FNRs, to resolutions similar to the OMI reduced the uncertainty in these retrievals. Systematic biases in OMI and TROPOMI NO 2 and HCHO retrievals tended to cancel out, resulting in all three satellite products comparing well to observed FNRs. However, while satellite-derived FNRs had minimal campaign-averaged median biases, unresolved errors in the indicator species did not cancel out in FNR calculations, resulting in large RMSE values compared to observations. Uncertainties in HCHO retrievals were determined to drive the unresolved biases in FNR retrievals.

Matthew S. Johnson↗
NASA NTRS1993

Numerical Simulation of a High Mach Number Jet Flow

The recent efforts to develop accurate numerical schemes for transition and turbulent flows are motivated, among other factors, by the need for accurate prediction of flow noise. The success of developing high speed civil transport plane (HSCT) is contingent upon our understanding and suppression of the jet exhaust noise. The radiated sound can be directly obtained by solving the full (time-dependent) compressible Navier-Stokes equations. However, this requires computational storage that is beyond currently available machines. This difficulty can be overcome by limiting the solution domain to the near field where the jet is nonlinear and then use acoustic analogy (e.g., Lighthill) to relate the far-field noise to the near-field sources. The later requires obtaining the time-dependent flow field. The other difficulty in aeroacoustics computations is that at high Reynolds numbers the turbulent flow has a large range of scales. Direct numerical simulations (DNS) cannot obtain all the scales of motion at high Reynolds number of technological interest. However, it is believed that the large scale structure is more efficient than the small-scale structure in radiating noise. Thus, one can model the small scales and calculate the acoustically active scales. The large scale structure in the noise-producing initial region of the jet can be viewed as a wavelike nature, the net radiated sound is the net cancellation after integration over space. As such, aeroacoustics computations are highly sensitive to errors in computing the sound sources. It is therefore essential to use a high-order numerical scheme to predict the flow field. The present paper presents the first step in a ongoing effort to predict jet noise. The emphasis here is in accurate prediction of the unsteady flow field. We solve the full time-dependent Navier-Stokes equations by a high order finite difference method. Time accurate spatial simulations of both plane and axisymmetric jet are presented. Jet Mach numbers of 1.5 and 2.1 are considered. Reynolds number in the simulations was about a million. Our numerical model is based on the 2-4 scheme by Gottlieb & Turkel. Bayliss et al. applied the 2-4 scheme in boundary layer computations. This scheme was also used by Ragab and Sheen to study the nonlinear development of supersonic instability waves in a mixing layer. In this study, we present two dimensional direct simulation results for both plane and axisymmetric jets. These results are compared with linear theory predictions. These computations were made for near nozzle exit region and velocity in spanwise/azimuthal direction was assumed to be zero.

Hayder, M. Ehtesham↗