Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Error Incidents”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

An investigation of reports of Controlled Flight Toward Terrain (CFTT)

Some 258 reports from more than 23,000 documents in the files of the Aviation Safety Reporting System (ASRS) were found to be to the hazard of flight into terrain with no prior awareness by the crew of impending disaster. Examination of the reports indicate that human error was a casual factor in 64% of the incidents in which some threat of terrain conflict was experienced. Approximately two-thirds of the human errors were attributed to controllers, the most common discrepancy being a radar vector below the Minimum Vector Altitude (MVA). Errors by pilots were of a much diverse nature and include a few instances of gross deviations from their assigned altitudes. The ground proximity warning system and the minimum safe altitude warning equipment were the initial recovery factor in some 18 serious incidents and were apparently the sole warning in six reported instances which otherwise would most probably have ended in disaster.

Porter, R. F.↗
NASA NTRS1995

Accurate estimation of sigma(exp 0) using AIRSAR data

During recent years signature analysis, classification, and modeling of Synthetic Aperture Radar (SAR) data as well as estimation of geophysical parameters from SAR data have received a great deal of interest. An important requirement for the quantitative use of SAR data is the accurate estimation of the backscattering coefficient sigma(exp 0). In terrain with relief variations radar signals are distorted due to the projection of the scene topography into the slant range-Doppler plane. The effect of these variations is to change the physical size of the scattering area, leading to errors in the radar backscatter values and incidence angle. For this reason the local incidence angle, derived from sensor position and Digital Elevation Model (DEM) data must always be considered. Especially in the airborne case, the antenna gain pattern can be an additional source of radiometric error, because the radar look angle is not known precisely as a result of the the aircraft motions and the local surface topography. Consequently, radiometric distortions due to the antenna gain pattern must also be corrected for each resolution cell, by taking into account aircraft displacements (position and attitude) and position of the backscatter element, defined by the DEM data. In this paper, a method to derive an accurate estimation of the backscattering coefficient using NASA/JPL AIRSAR data is presented. The results are evaluated in terms of geometric accuracy, radiometric variations of sigma(exp 0), and precision of the estimated forest biomass.

Holecz, Francesco↗
NASA NTRS1994

Communication Research in Aviation and Space Operations: Symptoms and Strategies of Crew Coordination

The day-to-day operators of today's aerospace systems work under increasing pressures to accomplish more with less. They work in operational systems which are complex, technology-based, and high-risk; in which incidents and accidents have far-reaching and costly consequences. For these and other reasons, there is concern that the safety net formerly built upon redundant systems and abundant resources may become overburdened. Although we know that human ingenuity can overcome incredible odds, human nature can also fail in unpredictable ways. Over the last 20 years, a large percentage of aviation accidents and incidents have been attributed to human errors rather than hardware or environmental factors alone. A class of errors have been identified which are not due to a lack of individual, technical competencies. Rather, they are due to the failure of teams to utilize readily available resources or information in a timely fashion. These insights began a training revolution in the aviation industry called Cockpit Resource Management, which later became known as Crew Resource Management (CRM) as its concepts and applications extended to teams beyond the flightdeck. Then, as now, communication has been a cornerstone in CRM training since crew coordination and resource management largely resides within information transfer processes--both within flightcrews, and between flightcrews and the ground operations teams that support them. The research I will describe takes its roots in CRM history as we began to study communication processes in order to discover symptoms of crew coordination problems, as well as strategies of effective crew management. On the one hand, communication is often the means or the tool by which team members manage their resources, solve problems, maintain situational awareness and procedural discipline. Conversely, it is the lack of planning and resource management, loss of vigilance and situational awareness, and non-standard communications that are implicated in accidents and incidents. NASA/Ames Crew Factors researchers have been developing a model of effective crew coordination in order to understand the sources of performance breakdowns, and to develop effective solutions and interventions. Because communication is a primary mechanism by which information is received and transmitted, and because it is observable behavior, we focus on these group processes in order to identify patterns of communication that distinguish effective from less effective crew performance. Since a prime objective is to develop training recommendations for enhancing communication skills, we interpret our findings in the context of relevant task and environmental conditions, role and procedural constraints, and the normal real-time parameters of flight operations. Another research objective is to consider how communication and coordination can be enhanced through design. For example, flight deck and hardware design as well as procedural and software design may greatly influence the efficiency with which crews communicate and coordinate their work. In addition, teams and tasks may be designed, organized, and trained so that team interactions with each other are based upon appropriately shared knowledge, procedures and situation awareness. In short, we are interested in enhancing communication practices through (1) the training of specific communication skills, and (2) the design of equipment, tasks, procedures, and teams that optimize smooth, unambiguous communication processes. Two examples of communication research will be described; one in aviation and one in space operations. The first example is a high-fidelity full mission simulation study which investigates the affect of flightdeck automation on crew coordination and communication (contrasting crew performance in the DC-9 vs. MD88). Additional information is contained in the original extended abstract.

Kanki, Barbara G.↗
NASA NTRSDate not supplied

Overlapping Conditions in IMPACT

Introduction The IMPACT 1.0 model assumes independence of 119 different medical conditions. That is, it is assumed that one medical event maps to a single medical condition. However, it is often the case that a single medical event may lead to several different concurrent conditions (e.g., a single accident resulting in multiple fractures, chest/abdominal trauma, and sepsis). There is a significant overlap between many of the conditions in ICL 1.0. For example, depression and anxiety are two separate conditions but often co-exist. This overlap may lead to an overestimation in the incidence calculation. In future iterations of the model, we plan to address progression of medical conditions. Methods There are two possible methods to approach progression of a medical condition. The first is to take any medical condition in ICL, calculate its incidence and determine its outcomes no matter what sequelae occur. For example, calculate the incidence of prostatitis and determine its metrics (e.g., loss of crew life, risk of medical evacuation or task time affected) no matter what the sequelae might be (sepsis, hydronephrosis, renal failure, etc.). The second approach is to take any medical condition in the ICL and calculate the outcomes based on transitions to any other condition. For example, calculate the incidence of nephrolithiasis and determine the incidence of each possible transition (e.g., hydronephrosis, renal failure, UTI, pyelonephritis, sepsis) and then determine its metrics. With perfectly informative evidence, the answers should be the same using either method. The question is which approach best reduces the opportunity for overlapping. Results The team identified 31 conditions that were the most likely to transition to a secondary condition such as sepsis and respiratory failure. It was felt that the first approach, as described above, would be the easiest to implement and would have the greatest reduction in overlapping conditions. The identified conditions were primarily infectious conditions, like UTI and pneumonia (which could lead to both respiratory failure and sepsis), toxic inhalations, cardiac arrest, seizures, and trauma. Once these conditions were identified, the conditions were divided between the four clinicians on the team to identify those that were not consistent with the others in way they were approached. There were 13 conditions that were found to be problematic. Some condition definitions needed to be changed to eliminate references to transitions or to update them in cases where the definitions were out of date. Some conditions required new evidence to correct the loss of crew life, and one condition was felt to have so much overlap that it was recommended for elimination. A second effort required modification of the sepsis incidence calculation to prevent double counting of the conditions, such as prostatitis, that could progress to sepsis. Conclusion The team made significant progress in clarifying the method for dealing with transitions from one medical condition to another. In addition, errors were found and corrected in definitions, incidence, and loss of crew life as well as a condition in which reference was made to a CLiFF that was no longer included. These modifications will provide greater fidelity in the IMPACT model and reduce overlap.

Arian Anderson↗
NASA NTRS1984

Analysis of normalized radar cross section (sigma-O) signature of Amazon rain forest using SEASAT scatterometer data

The normalized radar cross section (NRCS) signature of the Amazon rain forest was SEASAT scatterometer data. Statistics of the measured (NRCS) values were determined from multiple orbit passes for three local time periods. Plots of mean normalized radar cross section, dB against incidence angle as a function of beam and polarization show that less than 0.3 dB relative bias exists between all beams over a range of incidence angle from 30 deg to 53 deg. The backscattered measurements analyzed show the Amazon rain forest to be relatively homogeneous, azimuthally isotropic and insensitive to polarization. The return from the rain forest target appears relatively consistent and stable, except for the small diurnal variation (0.75 dB) that occurs at sunrise. Because of the relative stability of the rain forest target and the scatterometer instrument, the response of versus incidence angle was able to detect errors in the estimated yaw altitude angle. Also, small instrument gain biases in some of the processing channels were detected. This led to the development of an improved NRCS algorithm, which uses a more accurate method for estimating the system noise power.

Bracalente, E. M.↗
NASA NTRS1985

Total electron scattering cross sections. I - He, Ne, Ar, Xe

The apparatus and experimental procedures used to obtain total electron scattering cross sections are described, and results are presented for He, Ne, Ar and Xe in the 4-300 eV incident energy range, together with statistical errors. The results are generally found to be in good agreement with previous data except at low impact energies. Serious discrepancies remain in Xe below 20 eV impact energy.

Nickel, J. C.↗
NASA NTRS1985

Pilots of the future - Human or computer?

In connection with the occurrence of aircraft accidents and the evolution of the air-travel system, questions arise regarding the computer's potential for making fundamental contributions to improving the safety and reliability of air travel. An important result of an analysis of the causes of aircraft accidents is the conclusion that humans - 'pilots and other personnel' - are implicated in well over half of the accidents which occur. Over 70 percent of the incident reports contain evidence of human error. In addition, almost 75 percent show evidence of an 'information-transfer' problem. Thus, the question arises whether improvements in air safety could be achieved by removing humans from control situations. In an attempt to answer this question, it is important to take into account also certain advantages which humans have in comparison to computers. Attention is given to human error and the effects of technology, the motivation to automate, aircraft automation at the crossroads, the evolution of cockpit automation, and pilot factors.

Chambers, A. B.↗
NASA NTRS1992

Comparison of direct detection 50 Mbps Q-PPM receiver performance for AlGaAs and Nd doped laser transmitters

We present a theoretical and experimental performance comparison of a free space direct detection 50 Mbps quaternary pulse position modulation (Q-PPM) communications receiver for Nd:YAG and AlGaAs laser transmitters. Using silicon avalanche photodiodes (APD), we achieved a receiver sensitivity of 2.6 nW (264 incident photons/bit) at 1060 nm and 0.77 nW (59 incident photons/bit) at 810 nm (bit error rate (BER) of 10 exp -6). This is the best sensitivity ever reported for a direct detection receiver at 1060 nm. The experimental results were in good agreement with theoretical predictions.

Unger, G. L.↗
NASA NTRS1992

Numerical simulation of a 325 Mbit/s QPPM optical communication system

Optical digital receivers are being considered for intersatellite laser communication links. A demonstration system is being designed to operate at 325 MBit/s, using quaternary pulse position modulation (QPPM). Laboratory experiments have been conducted using a 50 MBit/s prototype system. A numerical model has been developed to simulate a QPPM optical receiver. The 50 MBit/s system was simulated to verify the validity of the model. The model was then used to simulate the projected behavior of the 325 MBit/s system. The model predicts a bit error rate of 10.6 at 38 incident photons per bit for 820 nm light.

Martino, Anthony J.↗
NASA NTRS1997

Analysis of Data from the Transient Gamma-Ray Spectrometer Experiment on the GGS/Wind Spacecraft

The data analysis from the TGRS experiment is continuing, although the UC Berkeley PI, K. Hurley, is no longer funded for this effort. This experiment has been returning data on the energy spectra and time histories of cosmic gamma-ray bursts since November 1994, and continues to operate in good health. Over a 3 year period ending in November 1997, 41 bursts have been detected simultaneously by TGRS and Dr. Hurley's Ulysses gamma-ray burst experiment. By comparing the times of arrival of a burst at Ulysses and TGRS, we can obtain an annulus of arrival directions for the event. Typical 3sigma annulus widths range from several arcminutes to tens of arcminutes. Because the WIND spacecraft is as far as several light-seconds from Earth, it is sometimes possible to obtain a second annulus using the Burst and Transient Source Experiment (BATSE) aboard the GRO spacecraft. 23 of the 41 bursts were also observed by this experiment. Generally, the two annuli intersect at grazing incidence, leading to a long, narrow error box which reduces somewhat the error circles obtained from BATSE alone. Table 1 summarizes the burst data from TGRS. We plan to defer the publication of these locations until a larger number of events has been accumulated. Measuring the energy spectra of cosmic gamma-ray bursts to search for line emission is one of the prime objectives of this experiment. However, an intense gamma-ray burst is required, or the statistics become too weak to draw meaningful conclusions. One such event has occurred to date, on August 22, 1995, and we have examined it in detail. The spectrum shows no evidence for lines, however.

Hurley, K.↗
NASA NTRS2000

Validation of Ocean Color Remote Sensing Data using a Moored Databuoy

NASA's Sea-Viewing Wide Field-of-View Sensor (SeaWiFS) aims to measure global ocean color from space to within 5% to provide insights into fundamental ocean processes. SeaWiFS must be backed by comprehensive calibration and validation programs if the mission is to achieve this. In situ measurements of normalized water-leaving radiance (L(sub wn)) made simultaneously with satellite measurements can complement on-orbit methods of tracking changes in the calibration of the satellite radiometer and allow end-to-end vicarious validation of the remotely-sensed data. A moored optical databuoy was developed at Plymouth Marine Laboratory, UK to measure L(sub wn) in the western English Channel. Tests indicate that the buoy is capable of measuring spectral incident irradiance with less than 10% error and water-leaving radiance with less than 20% error; these errors are reduced by averaging and show no bias. There were 24 match-ups with good quality SeaWiFS data at the buoy site during the ten months of deployment within the period May 1997 and September 1998. The differences between the buoy and SeaWiFS measurements of L(sub wn) were found to be variable and often large. The root-mean-square (RMS) differences varied from 102% at 412 nm to 50% at 555 nm. The RMS differences in measurements of L(sub wn) could be reduced to less than 18% by a combination of increasing the calibration coefficients of SeaWiFS by between 0.2 and 4.3% in the visible bands and by tuning the extrapolation of aerosol radiances from the near infrared to the visible wavelengths. These results imply that the monitoring of the absolute calibration of the SeaWiFS bands is imperfect and errors remain in the extrapolation of aerosol radiances for atmospheric correction.

Lavender, Samantha↗
NASA NTRS1996

Enhancing the Flight Safety Culture Through Training

In the 1970's, flight safety professionals became profoundly concerned about the prevalence of crew-caused accidents and incidents, and the role of human error in flight operations. As result, they initiated a change in the flight safety culture which has grown to significant proportions today. At the heart of the evolution were crew concepts such as flightdeck management, crew coordination, and cockpit resource management, concepts which seemed to target critical deficiencies. In themselves, the concepts were not new but their incorporation into training as a direct means of changing the flight safety culture was an untried, almost 'grassroots' approach. The targeted crew concepts and skills were not an integral part of the typical training program; the methods, curriculum, media, and even course content itself, would have to be developed and implemented from the bottom up. A familiar truism in the pilot culture is that you should 'Train the way you fly; Fly the way you train'. In short, training was expected to provide the pilot with practical operational skills that were consistent with the performance standards they were required to maintain and the operational demands they met on a daily basis. In short, one could not simply command crews to use good CRM; one would have to research and define these skills operationally as well as develop and implement a consistent and effective training program. Furthermore, one would need active support and collaboration among the research, industry and government communities in order to ensure acceptance and continued commitment. Additional information is contained in the original extended abstract.

Kanki, Barbara G.↗
NASA NTRS2023

Considerations for Software Fault Prevention and Tolerance

Mission or safety-critical spaceflight systems should be developed to both reduce the likelihood of software faults pre-flight and to detect/mitigate the effects of software errors should they occur in-flight. New data is available that categorizes software errors from significant historic spaceflight software incidents with implications and considerations to better develop and design software to both minimize and tolerate these most likely software failures.

Avionics↗
DOE OSTI2026

Errors in reconstruction of dichroic X-ray orientation tomography due to polarization rotation of the incident beam

Dichroic X-ray tomography is a technique in which the crystal orientation or magnetization of a sample is resolved in three dimensions. The best-known uses of this technique are for observation of magnetic moments via circular dichroism, using left- and right-handed circularly polarized X-ray beams. Another variant uses linear dichroism to resolve the crystal orientation. In both these techniques, it is assumed that the absorption of X-rays along a path inside a material can be computed as a line integral of a local absorption coefficient along the ray path. For linear dichroism, this assumption is inaccurate because the polarization of the beam changes along the propagation direction when the optic axis of the material is not aligned along the polarization. In this work, a finite-element Maxwell solver is used to simulate tomography and reconstructions. The propagation effect can lead to significant errors in the reconstructed orientations. These errors may be mitigated by taking data at additional angles or by operating at energies at which the dichroism is weak. An iterative approach is proposed which may allow accurate reconstruction with fewer data than would otherwise be required.

X-ray linear dichroism↗
NASA NTRS2019

Using Computational Flow Imaging to Optimize Filtered Rayleigh Scattering Measurements of an Isolator Shock Train

Filtered Rayleigh scattering (FRS) is a laser diagnostic where the intensity of elastically scattered light is measured after it passes through a molecular absorption filter. The filter removes background interference that overwhelms the relatively weak scattering from the gas molecules. However, with a filter, the measured light intensity depends on many of the scattering gas properties, including pressure, density, temperature, and velocity. In this work, CFD simulations of an isolator shock train flow field are input into a physics-based model to predict the values of FRS intensity measurements in a proposed experiment. The goal is to evaluate if a simplistic FRS setup (that utilizes one camera, laser, and absorption filter) can be used to accurately quantify number density despite the fact that the scattered light intensity also depends on other gas properties. It is found that the experimental setup can be optimized such that a linear relationship describes the number density with an average prediction error of 2%. The vast majority of the flow exhibits prediction errors of less than 3%, but small regions of the flow reach up to 11% error. A sensitivity analysis shows that the prediction error increases with the central wavelength of the incident laser light and decreases with the angle between the camera and laser propagation directions. The optimal experimental parameters are chosen based on a compromise between the prediction error, spatial resolution, and the amount of unfiltered light. In the future, the proposed FRS setup will be implemented to acquire new and valuable information on an isolator shock train, a flow field that has been traditionally studied using wall static pressure measurements and path-integrated visualization techniques, such as schlieren and shadowgraphy.

Hunt, Robin L.↗
NASA NTRS2002

Unsafe acts and unsafe outcomes in aircraft maintenance

Road safety studies using the Driver Behaviour Questionnaire (DBQ) have provided support for a three-way distinction between violations, skill-based errors and mistakes, and have indicated that a tendency to commit driving violations is associated with an increased risk of accident involvement. The aims of this study were to examine whether the three-way distinction of unsafe acts is applicable in the context of aircraft maintenance, and whether involvement in maintenance safety occurrences can be predicted on the basis of self-reported unsafe acts. A Maintenance Behaviour Questionnaire (MBQ) was developed to explore patterns of unsafe acts committed by aircraft maintenance mechanics. The MBQ was completed anonymously by over 1300 Australian aviation mechanics, who also provided information on their involvement in workplace accidents and incidents. Four factors were identified: routine violations, skill-based errors, mistakes and exceptional violations. Violations and mistakes were related significantly to the occurrence of incidents that jeopardized the quality of aircraft maintenance, but were not related to workplace injuries. Skill-based errors, while not related to work quality incidents, were related to workplace injuries. The results are consistent with the three-way typology of unsafe acts described by Reason et al. (1990) and with the DBQ research indicating an association between self-reported violations and accidents. The current findings suggest that interventions addressed at maintenance quality incidents should take into account the role of violations and mistakes, and the factors that promote them. In contrast, interventions directed at reducing workplace injury are likely to require a focus on skill-based errors.

Maintenance/manpower/methods↗
DOE OSTI2020

An improved method for direct incident solar radiation calculation from hourly solar insolation data in building energy simulation

Solar radiation considerably influences the energy consumption of buildings and the power production of building integrated photovoltaic (BIPV) systems. Hourly solar insolation (Wh/m 2 ), represented as the amount of solar irradiance collected on the ground during a 1-h period, is the most common solar radiation data available and widely used in weather files applied in building energy modeling programs (BEMPs). Because the solar beam and position vary over time, the use of hourly insolation data as the input might result in errors in the estimation of the direct incident solar radiation on a particular surface. In this study, methods used in BEMPs for direct incident solar radiation calculations are first analyzed, and an improved method adopting a new algorithm for estimating the solar irradiance is proposed. Furthermore, the algorithm assumes that the solar irradiance changes linearly within a 1-h period and can be estimated based on the solar irradiance at the half clock and slope. The collected direct normal solar irradiance data of 2016 from eight solar radiation stations in China were used to demonstrate the proposed method and evaluate its performance by comparing the results with those from three conventional methods used in BEMPs along with the ground truth measurements. In addition, in this study, factors affecting the accuracy of the calculation results are explored. The results of the estimated direct incident solar radiation show that the proposed method achieves the best accuracy, followed by the methods used in DOE-2, EnergyPlus, and DeST. The proposed method guarantees that the hourly direct solar insolation will remain the same and reflects the variation in the direct solar irradiance across a 1-h time frame. The proposed method can be adopted in BEMPs to improve the accuracy of the solar radiation calculation, thereby improving the accuracy of the simulated building performance and the BIPV production.

14 SOLAR ENERGY↗
NASA NTRS1983

Addressee Errors in ATC Communications: The Call Sign Problem

Communication errors involving aircraft call signs were portrayed in reports of 462 hazardous incidents voluntarily submitted to the ASRS during an approximate four-year period. These errors resulted in confusion, disorder, and uncoordinated traffic conditions and produced the following types of operational anomalies: altitude deviations, wrong-way headings, aborted takeoffs, go arounds, runway incursions, missed crossing altitude restrictions, descents toward high terrain, and traffic conflicts in flight and on the ground. Analysis of the report set resulted in identification of five categories of errors involving call signs: (1) faulty radio usage techniques, (2) call sign loss or smearing due to frequency congestion, (3) confusion resulting from similar sounding call signs, (4) airmen misses of call signs leading to failures to acknowledge or readback, and (5) controller failures regarding confirmation of acknowledgements or readbacks. These error categories are described in detail and several associated hazard mitigating measures that might be aken are considered.

Monan, W. P.↗