Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electrical properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Binder-Free Wood Converted Carbon for Enhanced Water Desalination Performance

Here, the design and synthesis of high-performance and economical carbon electrodes play a critical role in developing energy-efficient water desalination technologies. As a sustainable approach, low-cost and abundant biomass materials are promising candidates to prepare porous carbon for capacitive deionization. In this study, binder-free porous carbon sheets are successfully prepared using natural balsa, pine, and basswood by thermal carbonization and treated by chemical activation. The carbon electrode materials converted from balsa and pine exhibit a comparable salt adsorption performance by capacitive deionization due to the extensive surface area, substantial electrical property, and superior hydrophilic performance. The following activation treatment of the balsa-converted carbon further enhances the surface and electrical properties and benefits the desalination performance. The salt adsorption capacity of the activated balsa electrode exhibits 12.45 mg g -1 . Additionally, 19.52 mg g -1 Pb 2+ and 20.06 mg g -1 Cr 3+ heavy metal adsorption capacity is also observed with the activated balsa electrode in 100 mg L -1 PbCl 2 and 50 mg L -1 CrCl 3 , respectively. To the best of authors’ knowledge, this is the highest NaCl adsorption capacity performance reported thus far by using pure wood converted carbon as the electrode, and these promising results indicate that activated balsa is an extraordinary material for water desalination.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Demonstration of GaN-based metal–insulator–semiconductor junction by hydrogen plasma treatment

We demonstrate a nickel/insulating-GaN (i-GaN)/p-type GaN junction and investigate its electrical properties. The i-GaN is formed by exposure to a low-power hydrogen plasma to passivate the p-GaN layer. Cathodoluminescence spectroscopy of the i-GaN is used to understand the passivation effect of the hydrogen plasma on p-GaN. The junction shows very low leakage (<10−9 A at −50 V), excellent rectifying properties (∼107), high temperature stability, and blue light electroluminescence at forward bias. A bandgap model is proposed to illustrate the electrical properties of hydrogenated p-GaN and to understand the device characteristics.

Yang, Chen (ORCID:0000000230090882)↗
DOE OSTI2022

Electron doping of NdNiO 3 thin films using dual chamber CaH 2 annealing

Hydrogen donor doping has been exploited as a strategy to manipulate the electronic structure and electrical properties of functional oxide systems. Especially, the development of synthetic methods to achieve electron doping of perovskite rare-earth nickelate thin films utilizing interstitial hydrogen is highly desirable considering the rich electronic phase diagram hosting several functional properties. Here, in this work, we present the hydrogenation of NdNiO 3 (NNO) thin films using CaH 2 annealing and the resulting giant modulation of electrical resistivity in hydrogenated NNO (H–NNO) thin films. Magnetron sputtering was employed to deposit epitaxial ~60 nm-thin NNO films on single crystal LaAlO 3 (LAO) substrates. The formation of the pristine perovskite NNO phase was realized after annealing the films at 500 °C for 24 h. CaH 2 annealing of NNO thin films for time durations ranging from 1 to 6 h was performed in a vacuumed ampule with two interconnected chambers at 280 °C. The two-chamber design enables a simple and clean approach for hydrogen doping without physical contact between the powder and sample of interest. X-ray diffraction and Raman spectroscopy revealed the formation of NNO in pristine samples, and the subsequent hydrogen incorporation upon CaH 2 annealing without forming any impurity phases. The conversion of the oxidation state of Ni towards +2 upon CaH 2 annealing was probed using X-ray photoelectron spectroscopy and X-ray absorption spectroscopy. Consequently, a substantial increase in the room-temperature resistivity was observed upon CaH 2 annealing indicating the formation of a strongly correlated electronic configuration of Ni in H–NNO due to electron doping. Overall, the findings of this study highlight the versatility of CaH 2 annealing as an electron doping method to tune the electrical properties of correlated oxides at low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Li-Ion Battery Electrode Contact Resistance Estimation by Mechanical Peel Test

Li-ion battery electrode electronic properties, including bulk conductivity and contact resistance, are critical parameters affecting cell performance and fast-charge capability. Contact resistance between the coating and current collector is often the largest electronic resistance in an electrode and is affected by chemical, microstructural, and interfacial variations. Direct measurements of contact resistance and bulk conductivity have proven to be challenging. In their absence, a mechanical electrode peel test is often used to compare adhesion and electrical contact resistance. However, using a micro-flexible-surface probe, contact resistance can be directly determined. Here, this work compares contact resistance and mechanical peel strength of multiple commercial-grade HE5050 and NCM523 cathodes and graphite and silicon anodes. It was found that peel strength correlates well with contact resistance in a carefully curated data set (p < 0.05) and in some situations may be a good metric to estimate electrical properties. However, there were distinct outliers in the data set, indicating that peel strength may not accurately reflect electrical properties when there is significant variation in electrode composition. These results illustrate the value of the micro-flexible-surface probe in quantifying contact resistance and bulk conductivity to better understand how battery composition and processing steps affect microstructure and resulting cell performance.

25 ENERGY STORAGE↗
DOE OSTI2023

Inclusion of Biological Targets in the Analysis of Electrical Characteristics of Non-Thermal Plasma Discharge

In Plasma Medicine studies, the effect of non-thermal plasma (NTP) on biological targets is typically correlated with the amount of stable reactive oxygen and nitrogen species produced in a liquid medium. The effect of NTP and the response of the biological target on cellular redox mechanisms is overlooked in these investigations. Additionally, the influence of electrical properties of cells on the physical properties of NTP is neglected. Therefore, we used a floating electrode dielectric barrier discharge plasma to explore the impact of cell structure, size, and viability of the biological target on the physical properties of NTP. Lissajous figures were used to determine circuit capacitance and energy per cycle during NTP exposure of different cell suspensions. We show that both, structural integrity and active enzymic processes of cells change the electrical properties of NTP. Correlations were also drawn between NTP-produced hydrogen peroxide and nitrite with measured capacitance. Our studies indicate that the observed changes between different cell suspensions may be due to a feedback loop between the biological target and the NTP source. In future studies, a more detailed analysis is needed to improve the control of clinical NTP devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Point and extended defects in heteroepitaxial 𝛽−G⁡a 2 ⁢O 3 films

G⁡a 2 ⁢O 3 is emerging as an excellent potential semiconductor for high power and optoelectronic devices. However, the successful development of G⁡a 2⁢ O 3 in a wide range of applications requires a full understanding of the role and nature of its point and extended defects. Here, in this work, high quality epitaxial G⁡a 2 ⁢O 3 films were grown on sapphire substrates by metal-organic chemical vapor deposition and fully characterized in terms of structural, optical, and electrical properties. Then defects in the films were investigated by a combination of depth-resolved Doppler broadening and lifetime of positron annihilation spectroscopies and thermally stimulated emission (TSE). Positron annihilation techniques can provide information about the nature and concentration of defects in the films, while TSE reveals the energy level of defects in the bandgap. Despite very good structural properties, the films exhibit short positron diffusion length, which is an indication of high defect density and long positron lifetime, a sign for the formation of Ga vacancy related defects and large vacancy clusters. These defects act as deep and shallow traps for charge carriers as revealed from TSE, which explains the reason behind the difficulty of developing conductive G⁡a 2 ⁢O 3 films on non-native substrates. Positron lifetime measurements also show nonuniform distribution of vacancy clusters throughout the film depth. Further, the work investigates the modification of defect nature and properties through thermal treatment in various environments. It demonstrates the sensitivity of G⁡a 2 ⁢O 3 microstructures to the growth and thermal treatment environments and the significant effect of modifying defect structure on the bandgap and optical and electrical properties of G⁡a 2 ⁢O 3 .

defects↗
DOE OSTI2022

Thermodynamic and electrical transport properties of UTe 2 under uniaxial stress

Despite intense experimental efforts, the nature of the unconventional superconducting order parameter of UTe 2 remains elusive. This puzzle stems from reports of either a single or a double superconducting transition at ambient pressure as well as a complex pressure-temperature phase diagram. To address this issue, we measured the heat capacity and electrical resistivity of UTe 2 under compressive uniaxial stress σ applied along different crystallographic directions. We find that the critical temperature T c of the single observed bulk superconducting transition decreases with σ along [100] and [110] but increases with σ along [001]. Aside from its effect on T c , c-axis stress leads to a significant piezoresistivity. Importantly, an in-plane shear stress σ xy does not induce any observable splitting of the superconducting transition over a stress range of σ xy ≈ 0.17GPa. Furthermore, this result suggests that the superconducting order parameter of UTe 2 may be single component at ambient pressure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Electronic and optical properties of Zn-doped β-Ga 2 O 3 Czochralski single crystals

β-Ga 2 O 3 has several soluble deep acceptors that impart insulating behavior. In this study, we investigate Zn doping (0.25at.%) in bulk Czochralski and vertical gradient freeze β-Ga 2 O 3 . Representative crystals were assessed for orientation (electron backscatter diffraction and Raman spectroscopy), purity (glow discharge mass spectrometry and secondary ion mass spectrometry), optical properties (ultraviolet to near infrared absorption), and electrical properties (resistivity and current–voltage). Purity measurements indicate that Zn evaporation is insufficient to inhibit doping of Zn into β-Ga 2 O 3 . Hybrid functional calculations show Zn substitutes nearly equally on tetrahedral and octahedral sites, with less than ~0.1eV preference for the octahedral (Ga II ) site. Furthermore, calculations show that Zn Ga acts as a deep acceptor with trapping levels ~1.3 and ~0.9eV above the valence band for one and two holes, respectively. The solubility and electronic behavior of Zn dopants are consistent with measured concentrations >1×10 18 atoms/cm 3 and electrical measurements that show resistivity 10 11 –10 13 Ωcm, with no p-type conduction.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Toward improved PVDF-BaTiO 3 composite dielectrics: mechanical activation of the filler versus filler content

Abstract Barium titanate (BT) perovskite particles were surface modified by means of mechanical treatment and used as inorganic component in polyvinylidene fluoride (PVDF) based composites. The changes in electrical properties of the composite films with increasing in filler content were followed by dielectric spectroscopy, breakdown strength andD-Emeasurements. A comparison of the properties of the composites prepared with untreated and mechanically activated particles revealed that there is a significant difference in their performances at low filler concentrations (<20 wt%). Introduction of the surface modified ceramic particles into PVDF matrix led to an increase of the dielectric constant without affecting significantly the electrical breakdown strength. In contrast, when as received BT particles were used a filler, both dielectric constants and breakdown strengths of the composite films were lower than the corresponding values observed for the pure PVDF. At higher concentrations, however, the influence of pre-treatment of the filler on the effective electrical properties becomes less significant. The obtained results were discussed in terms of the pronounced crystallization of polarβandγcrystal phases of PVDF in the presence of surface modified BT fillers, which is confirmed by Raman spectroscopy.

Physics↗
DOE OSTI2022

Developing CdTe homojunctions applying high throughput deposition

In this project, we attempted to make CdTe homojunctions using single crystal p-type doped substrates and closed-space sublimation epitaxy (CSSE) n-type doped films. The project included modeling which determined the ideal thickness for the n-type layer as being <200 nm. Boules of high concentration indium-doped CdTe and CdSe 0.4 Te 0.6 (CST) were grown using modified vertical Bridgman (MVB) methods. Similarly, iodine-doped CdTe crystals were grown for the first time. Washington State University (WSU) stock phosphorus-doped CdTe was used as the p-type substrate layer. The crystals were characterized by Hall effect and time-resolved photoluminescence (TRPL, for electrical properties), photoluminescence microscopy (for uniformity), X-ray diffraction (for crystal structure), and glow discharge mass spectrometry (GDMS, for dopant and impurity concentration). CdTe:I crystals were also characterized by visible and infrared transmission measurements, and various Cd or Te heat treatments were performed to assess changes in optical and electrical properties. The grown n-type materials – CdTe:In, CdSe0.4Te0.6:In, and CdTe:I – were provided to the National Renewable Energy Laboratory (NREL) for growth of CSSE thick films for characterization by two photon TRPL (for carrier lifetime), electron back-scatter diffraction (EBSD, to assess epitaxy), and Hall effect. Several measurements of secondary ion mass spectroscopy (SIMS) were performed. Nearly 100% of the indium from the crystal was incorporated into the measured thick films, while only ~2-22% of the iodine from the crystal was incorporated. The net result of the diffusion issue is that homojunction devices created using CSSE have a buried homojunction, as indicated by the near infrared peak in the external quantum efficiency (EQE). Various parameterization of front and back contacts suggested that the poor device performance was primarily a result of this buried junction and not due to other effects. There may also be an issue with the CSSE film lifetime in addition to the dopant profile.

14 SOLAR ENERGY↗
DOE OSTI2025

What more can be done with XPS? Highly informative but underused approaches to XPS data collection and analysis

Because of the importance of surfaces and interfaces in many scientific and technological areas, the use of x-ray photoelectron spectroscopy (XPS) has been growing exponentially. Although XPS is being used to obtain useful information about the surface composition of samples, much more information about materials and their properties can be extracted from XPS data than commonly obtained. This paper describes some of the areas where alternative analysis methods or experimental design can obtain information about the near-surface region of a sample, often information not available in other ways. Experienced XPS analysts are familiar with many of these methods, but they may not be known to new or casual XPS users, and sometimes, they have not been used because of an inappropriately assumed complexity. The information available includes optical, electronic, and electrical properties; nanostructure; expanded chemical information; and enhanced analysis of biological materials and solid/liquid interfaces. Many of these analyses can be conducted on standard laboratory XPS systems, with either no or relatively minor system alterations. Topics discussed include (1) considerations beyond the “traditional” uniform surface layer composition calculation, (2) using the Auger parameter to determine a sample property, (3) use of the D parameter to identify sp 2 and sp 3 carbon information, (4) information from the XPS valence band, (5) using cryocooling to expand range of samples that can be analyzed and minimize damage, and (6) using electrical potential effects on XPS signals to extract chemically resolved electrical measurements including band alignment and electrical property information.

Baer, Donald R. [Pacific Northwest National Labora↗
DOE OSTI2026

Investigating the electrical transport properties and electronic structure of Zr 2 ⁢CuSb 3

The checkerboard lattice has been proposed to host topological flat bands as a result of destructive interference among its various electronic hopping terms. However, it has proven challenging to realize experimentally due to the difficulty of isolating this structure from any significant out-of-plane bonding while maintaining structural integrity. Here, in this study, single crystals of Zr 2 CuSb 3 , a potential candidate for the checkerboard lattice, were synthesized using the solution (self-flux) method, and their structure was confirmed via x-ray diffraction. Electrical-transport measurements indicate metallic behavior with electron-dominated carriers. Angle-resolved photoemission spectroscopy reveals multiple electron pockets and significant k z broadening due to its large c axis and low dispersion features in k z . Density-functional theory (DFT) calculations further disentangle the contributions from each high-symmetry plane, providing a comprehensive characterization of electronic behavior. The DFT calculations were then used to determine the orbital contributions of the bands and detect the out-of-plane bonding which prevented the flat bands from forming.

Downey, Eoghan [Univ. of Michigan, Ann Arbor, MI (↗
DOE OSTI2022

Development of a Novel Electrical Characterization Technique for Measuring Hidden Joint Contacts in Weapons Cavities (LDRD Final Report 218470)

This report summarizes research performed in the context of a REHEDS LDRD project that explores methods for measuring electrical properties of vessel joints. These properties, which include contact points and associated contact resistance, are “hidden” in the sense that they are not apparent from a computer-assisted design (CAD) description or visual inspection. As is demonstrated herein, the impact of this project is the development of electromagnetic near-field scanning capabilities that allow weapon cavity joints to be characterized with high spatial and/or temporal resolution. Such scans provide insight on the hidden electrical properties of the joint, allowing more detailed and accurate models of joints to be developed, and ultimately providing higher fidelity shielding effectiveness (SE) predictions. The capability to perform high-resolution temporal scanning of joints under vibration is also explored, using a multitone probing concept, allowing time-varying properties of joints to be characterized and the associated modulation to SE to be quantified.

42 ENGINEERING↗
DOE OSTI2019

Assessment of Physicochemical Properties of Electrical Arc Furnace Slag and Their Effects on Foamability

The composition of slags of an electric arc furnace (EAF) in a commercial melt shop was systematically analyzed with a focus on slag foaming. Basic behavior of FeO in an EAF slag was confirmed using fundamental thermodynamics. Monoxide ([Mg,Fe,Mn]O = M’O) and spinel ([Mg,Fe]Al{sub 2}O{sub 4}) phases in EAF slag were confirmed by X-ray diffraction analysis, and these results were interpreted in the context of equilibrium cooling calculation using FactSage™ software. Furthermore, the distribution of MgO with respect to the M’O-saturation limit at different basicity ratios (=CaO/SiO{sub 2}=C/S) and temperatures was evaluated. In particular, the relationship between MgO and FeO for C/S ratios ranging from 1.3 to 1.6 was considered with reference to phase equilibria. Foam height was affected by slag viscosity (η) and gas generation according to changes in C/S ratio and FeO content. Foaming index (Σ) decreased with the increasing C/S ratio and FeO content. The measured foam heights were relatively higher than the calculated values, and the result indicates that the effect of M’O on slag foaming in commercial process is remarkable. Therefore, slag chemistry should be optimized based on thermodynamic considerations and thermophysical properties to achieve good foaming characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fabric properties and electric efficiency limits of mechanical moisture extraction from fabrics

Residential clothes drying consume about 650 TBtu of primary energy per year in the United States, equivalent to 3% of primary residential energy consumption. There is a strong impetus to reduce the energy consumption of clothes dryers by both improving existing technology and developing alternatives that use fundamentally different drying mechanisms. Clothes drying technologies are broadly classified into either evaporative or mechanical drying. The focus of this paper is on mechanical drying, including vibrational, centrifugal, and press-based methods. In this work, the physical processes involved in these mechanical fabric drying processes were analyzed to develop general theories of mechanical cloth drying energy efficiency. Quantitative evaluation of the theories requires measured fabric properties. To accomplish this, a set of experiments was conducted on samples of a standard test fabric. The fabric was a cotton-polyester blend specified by the US Department of Energy to evaluate the standardized efficiency of all residential clothes dryers in the US. Mercury porosimetry experiments were conducted to determine the fabric pore size distribution, apparent density, and porosity. Elasticity experiments were conducted to determine the fabric’s Young’s modulus. Isostatic press experiments were conducted to establish a relationship between compression force and fabric moisture content. The data resulting from these experiments were combined with mathematical models developed in this work to calculate the theoretical maximum performance limits for mechanical drying of the standard fabric. The results of the analysis are used to make recommendations for the most promising technologies that offer the greatest potential energy savings for residential clothes drying.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The synthesis and electrical transport properties of carbon/Cr 2 GaC MAX phase composite microwires

While MAX phases offer an exotic combination of ceramic and metallic properties, rendering them a unique class of materials, their applications remain virtually hypothetical. To overcome this shortcoming, a sol–gel based route is introduced that allows access to microwires in the range of tens of micrometers. Thorough structural characterization through XRD, SEM, EDS, and AFM demonstrates a successful synthesis of carbonaceous Cr2GaC wires, and advanced low temperature electronic transport measurements revealed resistivity behavior dominated by amorphous carbon. Here, the tunability of electronic behavior of the obtained microwires is shown by a halide post-synthesis treatment, allowing purposeful engineering of the microwires’ electrical conductivity. Raman studies revealed the polyanionic nature of the intercalated halides and a slow decrease in halide concentration was concluded from time-dependent conductivity measurements. Based on these findings, the process is considered a viable candidate for fabricating chemiresistive halogen gas sensors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗