Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Economic Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

IACMI Project 4.2: Thermoplastic Composite Development for Wind Turbine Blades

(Section 5.1) Composites made from Arkema’s Elium® thermoplastic resin and Johns Manville fiberglass were researched during this project for applications in wind blade manufacturing. A techno-economic model was developed to model this wind blade manufacturing process using these materials in place of traditional composites made with thermoset resin. This model was based on manufacturing a 61.5-meter wind blade, which showed a 4.7% reduction in wind blade cost as compared traditional thermoset materials. These cost savings were not from the thermoplastic material costing less than traditional thermoset materials, but rather from decreased capital costs, faster cycle times and reduced energy requirements and labor costs. (Section 5.2) An infusion and curing model was developed for thermoplastic composite wind blades using PAM-RTM. The primary goal was to demonstrate the infusion simulation for the Elium® resin system on a 13-meter wind blade. Additionally, the exotherm temperature was predicted and compared to measurements, which showed model results within 10% of actual measurements. (Section 5.3) Composite laminate panels and composite sandwich panels with a balsa core were produced; specimens were cut and characterized. Similar composite specimens were made with Elium® thermoplastic resin and Hexion thermoset epoxy (RIMR135/RIMH1366) to enable comparisons between these resin systems. The static test methods included: tensile, compression, in-plane shear, interlaminar shear, flexural, sandwich core shear flexure, and single cantilever beam tests for sandwich beams. Fatigue testing at room temperature was completed to composite laminate panels at a stress ratio of R=0.1 and R=10. In addition, fatigue testing to laminate panels was completed at -30°C, and at room temperature after conditioning specimens at 70°C and 90% relative humidity. Overall, mechanical test results from Elium® composites are similar to epoxy composites. (Section 5.4) Elium composite panels were produced with intentional defects such as voids and nonwetting of fibers to begin to understand performance sensitivity to defects. A thermal digital image correlation (TDIC) method provides high spatial resolution strain field at elevated temperatures and can be used to identify defective regions within composite panels. Flexural modulus differences of 21% were seen between defect and non-defect panels. Other Elium® composite panels were forced to be defective by boiling the resin after infusion, which created voids throughout the composite laminate. X-ray computed tomography scanning was used to view the internal structure of the defect panels. Defect panels had a significant reduction in fatigue life as compared to baseline panels produced without intentional defects. (Section 5.5) Lap shear specimens were fabricated to compare the lap shear strength of an off-the-shelf adhesive (Plexus MA590) and two new adhesives developed by Arkema (Bostik SAF30 90 and Bostik SAF30 120). ISO standard 4587:2003 was used to standardize the testing method and sample fabrication. Lap shear specimens were made at 1mm, 3mm, and 10mm thicknesses. The Bostik adhesive lap shear test results were similar to Plexus for all thicknesses. (Section 5.6) Fiber-reinforced polymer (FRP) composites are typically used in high-performance applications (e.g., aerospace), and their expansion into high-volume industries (e.g. consumer automotive and wind turbine blade manufacturer or similar) is hindered by their cost and a lack of efficient manufacturing techniques. Monitoring the curing process of these composites during manufacturing can improve the efficiency of the process, and therefore reduce the manufacturing cost. Cure monitoring techniques were developed that use probabilistic estimation methods and surface temperature measurements made using infrared cameras. These techniques enable real-time monitoring of the infusion process to locate manufacturing flaws, and they can, potentially, estimate residual stresses in the part. Their commercialization will help facilitate expansion of FRP composites in high-volume industries. (Section 5.7) A 13-meter composite wind blade was produced with Elium® resin and Johns Manville fiberglass; this blade was made with VARTM processing similar to how megawatt-scale wind blades are currently manufactured, but no post-mold heating was used for this thermoplastic composite blade. The wind blade underwent full-scale validation for static loading (4-different load orientations) and flapwise fatigue loading to simulate 20-years of operational loads. The thermoplastic composite wind blade withstood the loading without any noted issues and performed similar to results from a previous full-scale validation to an equivalent epoxy composite wind blade produced with the same blade molds. (Section 5.8) A study was conducted to determine the feasibility of recycling composite wind turbine blade components fabricated with glass fiber reinforced Elium® thermoplastic resin. Dissolution, which is a process unique to thermoplastic matrices, allows recovery of both the polymer matrix and full-length glass fibers, while maintaining their stiffness and strength throughout the recovery process. The economics of recycling is favorable if 50% of the glass fiber is recovered and resold for a process of $\$$ 0.28/kg, and 90% of the resin is recovered and resold at a price of $\$$ 2.50/kg.(Section 10) Recommendations are outlined for commercializing thermoplastic resin for composite wind blade production, in addition to recommended areas for future research.

17 WIND ENERGY↗
DOE OSTI2022

Techno-Economic Wind Blade Manufacturing Model to Identify Opportunities for Cost Improvements Phase II IACMI Project 4.6/4.8

In IACMI Project 4.6 and IACMI Project 4.8, an Excel-based Techno-Economic Model (TEM) of the manufacturing process for composite wind turbine blades and a DELMIA Factory Flow Simulation of a generic wind blade manufacturing facility was developed. Together, these two tools provide a combined economic modeling capability that accounts for the material, labor, overhead and full-lifecycle operating costs associated with wind blade manufacturing as well as the impact of process flow and factory layout on overall manufacturing efficiency. The tools provide a novel means of detailed comparative analysis of the economic feasibility of proposed technologies and process changes for blade manufacturing. The modeling tools were developed with close support from members of industry and visits to multiple blade manufacturing facilities. With industry oversight, a detailed generalized manufacturing process plan and facility layout were developed with manufacturing parameters, material costs and economic factors based on historical data. Dassault Systèmes and the University of Texas at Dallas (UTD) contributed to the development of the Techno-Economic Model by providing macros to enable the generation of Bill of Material (BOM) data from a 3D blade design in either CATIA or NuMAD format, respectively. The TEM was built with the capability to directly import a Bill of Materials for economic analysis, and with the addition of the macros provided by Dassault and UTD, the TEM can directly import blade designs from both CATIA and NuMAD file formats. The modeling tools developed in Project 4.6 were used to investigate four wind blade manufacturing concepts in detail and select one to explore with laboratory-scale experimentation in Project 4.8. The four manufacturing concepts that were investigated were down-selected by the full project team from a larger list of concepts. The selections were made based on a number of criteria ranking viability and level of interest for each concept. The ‘One-Step Close’ manufacturing concept was ultimately selected for investigation in Project 4.8 and the demonstration was performed at the NREL CoMET facility. The TPI advanced manufacturing facility in Warren, RI contributed the production of several prototype components, the designs for which were developed by Janicki Industries. The demonstration project provided clear indication of the viability of the One-Step Close manufacturing concept for blade manufacturing and good validation of the Techno-Economic Model’s prediction of its economic impact.

17 WIND ENERGY↗
DOE OSTI2021

10 New Insights in Climate Science 2020 - a Horizon Scan

We summarize some of the past year’s most important findings within climate change-related research. New research has improved our understanding of Earth’s sensitivity to carbon dioxide, finds that permafrost thaw could release more carbon emissions than expected and that the uptake of carbon in tropical ecosystems is weakening. Adverse impacts on human society include increasing water shortages and impacts on mental health. Options for solutions emerge from rethinking economic models, rights-based litigation, strengthened governance systems and a new social contract. The disruption caused by COVID-19 could be seized as an opportunity for positive change, directing economic stimulus towards sustainable investments.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

Climate-Driven Divergence in Biophysical and Economic Impacts of Agrivoltaics

Increasing global demands for food and energy necessitate innovative land-use solutions. Agrivoltaics, colocating solar photovoltaics with agriculture, shows promise, but its widespread adoption faces complex biophysical and economic trade-offs in a changing climate. Here, we develop an integrated biophysical-economic modeling framework to quantify how agrivoltaics affect biophysical and economic impacts across the Midwestern United States under both current and project climate conditions. We find strong regional divergences driven by climate gradients. In the humid eastern Midwest, solar panel shading limits photosynthesis, leading to reduced yields (maize -24%; soybean -16%) and lower farmers' profitability (maize -16%; soybean -2%) compared to conventional agriculture. Conversely, in the semiarid western region, shading alleviates heat and water stress, moderating yield reductions for maize (-12%) and even boosting soybean yields (+6%), resulting in improved economic returns (-6% for maize; +9% for soybean), for a scenario with 33% photovoltaic ground coverage ratio. Although agrivoltaics generate substantial electrical energy across all regions, high upfront installation costs challenge solar developers compared to standalone solar photovoltaics. However, our analysis identifies “win-win” opportunities where soybean-based agrivoltaics in the semiarid region produce economic benefits for both farmers and solar developers, highlighting the necessity for region-specific designs tailored to local climate conditions. Critically, future climate projections indicate eastward expansion of semiarid conditions, broadening areas where agrivoltaics can mitigate crop yield penalties (even boosting yield) and improve overall profitability, especially under high-emission scenarios. The results provide a mechanistic and economically integrated understanding essential for developing evidence-based and region-specific strategies to scale agrivoltaics in a changing climate.

14 SOLAR ENERGY↗
DOE OSTI2023

Jobs and Economic Development Impact (JEDI) Models

The Jobs and Economic Development Impact (JEDI) models (https://www.nrel.gov/analysis/jedi/) are publicly available, user-friendly tools designed to estimate the economic impacts of both construction and operation of power generation and biofuel plants at a local (usually state) level. Based on project-specific and default inputs (from techno-economic analysis data and NREL's expertise), these models estimate the number of jobs and economic benefits to a region that could reasonably be supported by a particular project. Underlying these calculations is an input-output framework that models the local economy as a network of sectors buying and selling to one-another, creating a multiplier effect. Over the last decade, JEDI has been widely used by both the academic and private sectors, serving as the foundations for multiple peer-reviewed publications and impact analysis reports.

economic impact analysis↗
DOE OSTI2023

A2E2G (Atmosphere to Electrons to the Grid platform) [SWR-23-22]

A2E2G is a platform that integrates 1) forecasting tools to account for weather uncertainty, with 2) aerodynamic wind plant models to account for wake dynamics and wind plant operation, and 3) economic models to advise on operation for a wind power plant that offers grid services in addition to energy. The A2E2G platform can be used as a high-level controller for a wind plant for market participation and real-time wind plant control. The A2E2g platform is a holistic Python tool with modules that can be run to 1) advise on market participation and 2) control and operate a wind power plant in real time. The A2E2g framework assumes two stages: the first stage is in day-ahead and the second stage is in real-time. Managing uncertainty is key in the first stage and managing variability is key in the second stage. The different components have models written and developed in the Python programming language. The code is assembled into a Python package and can be easily downloaded and installed from the A2E2g repository (https://github.com/NREL/a2e2g).

Sinner, Michael↗
DOE OSTI2026

Climate impacts in scenarios: time to close the loop?

Reaching a full understanding of the consequences of climate change for society and ecosystems, and the ensuing needs for adaptation, requires a consideration of the interactions between human and Earth systems. Currently, however, climate research largely separates the influence of society on climate from the influence of climate on society; that is, it doesn’t “close the loop.” A primary example of this approach is the generation and use of earth system model (ESM) simulations in the climate change research community. Large-scale socio-economic models, known as integrated assessment models (IAMs), are used to project emissions and land use change which serve as input to ESMs. ESM projections then serve as input to models of impacts on society and ecosystems. But, according to this modeling chain, those impacts do not affect the emissions and land use that drove the ESMs in the first place. Previous work has not drawn firm conclusions on whether this feedback would be large enough to warrant explicitly accounting for it. Two prominent possibilities, however, are that emissions and land use scenarios representing the high and low ends of the plausible range of future climate change are both too extreme. The high-end scenario may miss damaging impacts that would reduce economic activity, and therefore emissions, while the low-end scenario may ignore climate feedbacks that would make large-scale land-based carbon removal ineffective and therefore would hamper mitigation at the level assumed by the scenario. In this piece, we identify the opportunities and challenges that implementing such feedback loops would face. We argue that recent developments in climate impact research, human system modeling and ESM emulation make the time ripe to use IAMs in a structured model intercomparison exercise. Model intercomparison projects have benefitted the climate modeling community for decade snow, and more recently have also benefitted the impact modeling community. An IAM intercomparison focused on integrating impacts could make large strides in testing the implications of these feedbacks and assessing whether closing the loop would fundamentally change our outlook on future climate changes and their consequences.

Tebaldi, Claudia↗
DOE OSTI2022

Techno-Economic Analysis of Recuperated Joule-Brayton Pumped Thermal Energy Storage

This article describes a techno-economic model for pumped thermal energy storage systems based on recuperated Joule-Brayton cycles and two-tank liquid storage. Models have been developed for each component, with particular emphasis on the heat exchangers. Economic metrics such as the power and energy capital costs (i.e., per-kW and per-kWh capacity) and levelized cost of storage are evaluated by gathering numerous cost correlations from the literature, thereby enabling estimates of uncertainty. It is found that the use of heat exchangers with effectivenesses up to 0.95 is economically worthwhile, but higher values lead to rapidly escalating component size and system cost. Several hot storage fluids are considered; those operating at the highest temperatures (chloride salts) improve the round-trip efficiency but the benefit is marginal and may not warrant the additional material costs and risk when compared to lower-temperature nitrate salts. Cost-efficiency trade-offs are explored using a multi-objective optimization algorithm, yielding optimal designs with round-trip efficiencies in the range 59-72% and corresponding levelized storage costs of 0.12 0.03 and 0.38 0.10 $/kWhe. Lifetime costs are competitive with lithium-ion batteries for discharging durations greater than 6 h under current scenarios.

Carnot battery↗
DOE OSTI2022

Estimating production cost for large-scale seaweed farms

Seaweed farming has the potential to produce feedstocks for many applications, including food, feeds, fertilizers, biostimulants, and biofuels. Seaweeds have advantages over land-based biomass in that they require no freshwater inputs and no allocation of arable land. To date, seaweed farming has not been practiced at scales relevant to meaningful biofuel production. Here we describe a techno-economic model of large-scale seaweed farms and its application to the cultivation of the cool temperate species Saccharina latissima (sugar kelp) and the tropical seaweed Eucheumatopsis isiformis. At farm scales of 1000 ha or more, our model suggests that farm gate production costs in waters up to 200 km from the onshore support base are likely to range between $\$$200 and $\$$300 per dry tonne. The model also suggests that production costs below $\$$100 per dry tonne may be achievable in some settings, which would make these seaweeds economically competitive with land-based biofuel feedstocks. While encouraging, these model results and some assumptions on which they are based require further field validation.

09 BIOMASS FUELS↗
DOE OSTI2023

Thermal & Electrochemical Power Plant Design and Cost Estimation

Public textbook for "Thermal & Electrochemical Power Plant Design and Cost Estimation: Version#1" This public textbook is an extension of class notes from Carnegie Mellon University courses: Energy System Modeling (24-722) and Fuel Cell Systems (24-262), taught by Dr. Nicholas Siefert between 2010-2021. Textbook includes some references to class notes from Dr. Shawn Litster, Department of Mechanical Engineering, Carnegie Mellon University. Textbook covers the equilibrium and nonequilibrium thermodynamics of power systems as well as an overview of system and economic modeling of these systems. There is in-depth coverage of (a) entropy generation, (b) exergy and (c) the redox state of molecules in equilibrium with the natural environment. This textbook is integrated with other materials (such as lecture slides, solved homeworks, and solved exams) that will be posted to the PowerShare: Energy Systems Modeling group on EDX. Publication Number: DOE/NETL-2023/3913

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Modeling and simulation to investigate the electrification potential of medium- and heavy-duty vehicle fleets

This project involves developing and integrating new modeling tools to simulate the dynamics of electric medium- and heavy-duty fleet vehicle adoption. A technical and economic modeling tool, combining a data-driven hardware cost model with a cost-optimal charging strategy microsimulation, enables tailored analysis of the costs and benefits of electrifying individual fleets. Next, a novel text synthesis process, applied to a curated corpus of literature, quantifies trade-offs between technical, economic, and other factors in the fleet vehicle procurement decision. The outcomes of these tasks combine with knowledge from recent literature on fleet decision processes to specify the vehicle procurement model used by fleets in an agent-based model of the medium- and heavy-duty electric vehicle market. This model embodies an especially disaggregated approach to adoption modeling, internalizing factors and dynamics that conventional adoption models externalize. In particular, explicitly modeling the formation and diffusion of opinions among agents enables experiments that conventional models cannot support. Demonstrations show, for example, that increasing the extent of interactions between populations with different proclivities to electric vehicles has an asymmetrical outcome. High-proclivity electric vehicle adoption is generally unaffected as interactions increase, but low-proclivity adoption is accelerated. By representing individual fleets' requirements and costs at a high level of detail, incorporating an adoption decision model informed by a wide body of empirical research, and broadening the array of variables and dynamics available for experimentation, this integrated model offers a new way to understand the urgent challenge of eliminating emissions from the most emissions-intensive transportation sectors.

Trinko, David A.↗
DOE OSTI2020

Building the Foundation for Assessing GOM Offshore CO 2 EOR and CO 2 Storage [Slides]

This PowerPoint Presentation was used in a seminar given to headquarters personnel as well as other stakeholders. The seminar took place on August 7, 2020. The presentation introduces three offshore oil field case studies: Cognac, Petronius, and Horn Mountain. The NETL/ARI Gulf of Mexico (GOM) offshore large oil fields data base provides a strong foundation for the upcoming offshore GOM CO 2 storage and enhanced oil recovery (EOR) assessment. The three Case Studies show that significant volumes of CO 2 can be securely stored in the offshore GOM and that notable volumes of addition oil can be recovered from this area with CO 2 EOR. The Case Studies also show that the CO 2 Prophet Model can serve as an excellent assessment tool. The “next steps” include building the cost and economics models for offshore CO 2 transportation and particularly for conducting seafloor CO 2 EOR and CO 2 storage.

02 PETROLEUM↗
DOE OSTI2025

Low-Cost Sulfur Thermal Storage for Solar Industrial Process Heat Applications

Industrial process heat (IPH) is one of the largest energy demands in U.S., representing about 10% of all domestic energy consumption. Fuel costs to generate this industrial process heat are generally a top three cost for industry, a major component in American manufacturing competitiveness. Roughly 60% of US IPH demand (about 6,500 TBtu annually) falls in the medium-temperature range of 100–250 °C. While concentrated solar thermal (CST) technologies can provide a cost-effective source of heat in this temperature range, solar intermittency limits their adoption in industries that operate 24/7. Element 16 Technologies, Inc. developed a low-cost sulfur thermal energy storage (TES) technology to bridge this gap by capturing excess solar heat during the day and dispatching it reliably during non-solar hours. The core innovation is the use of sulfur, an abundant, industrial waste byproduct that costs ten times less than molten salt used in commercial TES systems. The overall goal of the project was to advance the design and development of molten sulfur TES to a manufacturing-relevant prototype stage for solar industrial process heat applications, while establishing and validating a realistic pathway to commercial success. Key tasks included corrosion and mechanical durability testing to identify cost-effective materials, design investigations using physics-based simulation tools, techno-economic evaluations of system lifetime costs, and pilot-scale testing for performance verification. Corrosion testing of steel alloys under cyclic molten sulfur conditions showed that austenitic stainless steels in the 300 series performed particularly well, with no structural degradation of welds or joints. Thermal cyclic testing of pilot sulfur TES units up to 1.5 MWh quantified charge/discharge rates, heat losses, round-trip efficiency and validated the system's capability to operate effectively under intermittent charging conditions. A techno-economic model, informed by sulfur TES performance model validated using pilot test data, showed that hybrid solar+sulfur TES+NG boiler systems are economically competitive with incumbent natural gas boilers for multiple locations in the southwest US. In summary, this project established molten sulfur TES as a technically viable pathway to improve economic competitiveness of American manufacturing by lowering the cost of solar industrial process heat.

14 SOLAR ENERGY↗
DOE OSTI2022

Predicting Performance of Macroalgae Farms with Hydrodynamic and Biological Modeling

As part of the ARPA-E MARINER program a set of simulation tools and findings were developed for the hydrodynamic, biological, and economic modeling of large scale offshore macroalgae farms. Results suggest the utility of the tools in understanding the complex interplay of design choices and environmental conditions on the structural loading and farm performance which drive the costs for macroalgae production.

09 BIOMASS FUELS↗
DOE OSTI2024

Screening Tool for Equitable Adoption and Deployment of Solar (STEADy Solar)

The Screening Tool for Equitable Adoption and DeploYment of Solar (STEADy Solar) is a database and mapping tool designed to promoting clean energy investments for low-income communities across the United States. The tool indicates locations that may be eligible for the Investment Tax Credit bonus adders defined in the 2022 Inflation Reduction Act (IRA) and combines this information with demographics, social vulnerability, solar technical potential, solar economics (modeled net present value), and building counts by use-type. It can be used by states, municipalities, community-based organizations, developers, and researchers to identify sites where solar projects may be economical and where federal incentives may be available to support equitable adoption of solar. Specific values include: Areas eligible for the Energy Communities Tax Credit Bonus Program (including brownfield site counts) Areas eligible for the Low Income Communities Bonus Credit Program (including Tribal Lands, and covered affordable housing project counts) Areas categorized as disadvantaged by Justice40 Commercial and Residential Solar economics characterized by the Net Present Value and Simple Payback Period Total Population, Race, and Ethnicity Median Household Income, Poverty rate, Household Tenure Social Vulnerability Count of buildings, developable rooftop solar capacity (in kWdc) and estimated annual generation potential (in kWh) on four building types: Government General Services, Government Emergency Response, Grade Schools, and Colleges/Universities. The linked report describes the STEADy dataset metadata and presents high level insights from the data. The downloadable and formatted excel dataset makes it easy for users to gain insights for their locations. Supporting .csv and shapefiles provide users with the full data to run their own analyses on equitable solar siting.

14 SOLAR ENERGY↗
DOE OSTI2023

The cost of direct air capture and storage can be reduced via strategic deployment but is unlikely to fall below stated cost targets

Carbon dioxide removal (CDR) is necessary to minimize the impact of climate change by tackling hard-toabate sectors and historical emissions. Direct air capture and storage (DACS) is an important CDR technology, but it remains unclear when and how DACS can be economically viable. Here, we use a bottom-up engineering-economic model together with top-down technological learning projections to calculate plant-level cost trajectories for four DACS technologies. Our analysis demonstrates that the costs of these technologies can plateau by 2050 at around $\$$100-600 t-CO 2 -1 mainly via capital cost reduction through aggressive deployment, but still exceed the optimistic targets defined by countries such as the US (i.e., $\$$100 t-CO 2 -1 ). A further analysis of existing policy mechanisms indicates that strong, project-catered policy support will be required to create market opportunities, accelerate DACS scale-up and lower the costs further. Our work suggests that strategic DACS deployment and operation must be coupled with strong policies to minimise the cost of DACS and maximise the opportunity to make a planet-scale climate impact.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

A Demonstration System for Geological Thermal Energy Storage of Concentrating Solar Thermal

Energy storage is increasingly necessary as variable energy technologies are deployed. Seasonal energy storage can shift energy generation from the summer to the winter, but these technologies must have extremely large energy capacities and low costs. Geological Thermal Energy Storage (GeoTES) is proposed as a solution for long-term energy storage [1]. Excess thermal energy can be stored in permeable reservoirs such as aquifers and depleted hydrocarbon reservoirs for several months. The energy capacity cost of GeoTES is very low which makes it suitable for both daily- and seasonal storage of Concentrating Solar Thermal (CST) energy, thus enabling CST to provide value to electricity markets and thermal energy off-takers. A CST-GeoTES demonstration system has been funded by the U.S. Department of Energy, Solar Energy Technology Office. In this article, we will describe this demonstration system and progress that has been made in its development. The demonstration system will comprise a 2 MWth parabolic trough with an 8m aperture developed by Gossamer Space Frames, seven wells, and a 100 kWe power cycle. The demonstration system will be deployed in Kern County, California by Premier Resource Management. A techno-economic model for CST-GeoTES systems has also been developed [3] and is applied to the demonstration system and its planned future expansion. The model integrates the output of specialist models of each subsystem, which enables the performance and cost of both the subsurface and surface systems to be captured. Off-design models enable the performance to be evaluated at each hour of the year, before being aggregated to evaluate the economic potential of CST-GeoTES. Initial analysis indicates that CST-GeoTES can provide long duration energy storage capabilities with low marginal costs of energy capacity - leading to a low value of Levelized Cost of Storage (LCOS) compared to alternative technologies, see Figure 2. In this article, we investigate the cost and performance of the specific demonstration site being developed by PRM and explore a range of operational profiles that can deliver different value streams, such as daily and seasonal storage, capacity, and resiliancy.

14 SOLAR ENERGY↗